Develop Bugs

Downgrade to 4.1.1 HELP!!

Hi everyone, i am trying to downgrade my samsung galaxy s3 t999 from 4.1.2 to 4.1.1 so i could UNLOCK my WIND MOBILE phone and use it with ROGERS sin card. I tried to do the process via ODIN but i am getting this message :
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T999UVDLJC_T999TMBDLJC_T999UVDLJC_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
I REALLY NEED TO USE THE PHONE AS SOON AS POSSIBLE !! SOMEBODY HELP ME PLEASE !!
THANKS !

numberone1 said:
Hi everyone, i am trying to downgrade my samsung galaxy s3 t999 from 4.1.2 to 4.1.1 so i could UNLOCK my WIND MOBILE phone and use it with ROGERS sin card. I tried to do the process via ODIN but i am getting this message :
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T999UVDLJC_T999TMBDLJC_T999UVDLJC_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
I REALLY NEED TO USE THE PHONE AS SOON AS POSSIBLE !! SOMEBODY HELP ME PLEASE !!
THANKS !
Click to expand...
Click to collapse
I do believe the firmware you are attempting to flash is not for your device. That firmware is for the SGH-T999, not the SGH-T999v. Hopefully you didn't brick your phone. Download the proper firmware and try again.
It was only the modem that you needed to flash, anyhow. Not the entire firmware package.

my phone works perfectly though, COULD you please tell me which firmware should i download then to do the downgrade ??

You gave conflicting information. You said it's a T999, but also it's from Wind. The Canadian carriers use model T999V. It is different. I'm assuming you have the T999V, in which case you simply just need to download the WIND 4.1.1 firmware for the T999V (build UVLDLL1 If I remember right). It's all in my firmware thread. Link in Sig.
And look under the battery to know what model you have.
Sent from my SCH-I535 using Tapatalk 4

Please read forum rules before posting
Questions and Help issues go in Q&A and Help section
Thread moved
Thank you for your cooperation
Friendly Neighborhood Moderator

Help Galax S3 T999V wont restart after downgrade to 4.1.1
Hello
I was trying to down-grade Galaxy S3 (T999V wind mobile) 4.1.2 to 4.1.1.
I used Odin to load the new Firmware, as soon as the phone restarted i got the following message:
"Unfortunately, the process android.process.media has stopped"
what have i done wrong and what should i do in order to fix that?
thank you in advance
Kofiko

kofikom said:
Hello
I was trying to down-grade Galaxy S3 (T999V wind mobile) 4.1.2 to 4.1.1.
I used Odin to load the new Firmware, as soon as the phone restarted i got the following message:
"Unfortunately, the process android.process.media has stopped"
what have i done wrong and what should i do in order to fix that?
thank you in advance
Kofiko
Click to expand...
Click to collapse
This is no problem
wipe you're internal storage in recovery, it's best to do a factory reset in the stock recovery including caches and reboot and enjoy a fresh stock ROM

How to flash the modem only
Aerowinder said:
I do believe the firmware you are attempting to flash is not for your device. That firmware is for the SGH-T999, not the SGH-T999v. Hopefully you didn't brick your phone. Download the proper firmware and try again.
It was only the modem that you needed to flash, anyhow. Not the entire firmware package.
Click to expand...
Click to collapse
Can you please tell me how to flash the modem?

[Q] Odin fails for DN3 rom wifi fix?

Hello all
So im trying to flash the MJ5 bootloarder for my note 2 in order to the wifi working for the DN3 rom. But every time i try to flash the bootloader in odin if fails. What should I do?
Thanks
this is what it says in the message box:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BL_N7100XXUEMJ5_1903221_REV04_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> sboot.bin
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)

weedmon21 said:
Hello all
So im trying to flash the MJ5 bootloarder for my note 2 in order to the wifi working for the DN3 rom. But every time i try to flash the bootloader in odin if fails. What should I do?
Thanks
this is what it says in the message box:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BL_N7100XXUEMJ5_1903221_REV04_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> sboot.bin
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
+1

On which bootloader are you currently?
Sent from my GT-N7100 using XDA Premium 4 mobile app

manan999583 said:
On which bootloader are you currently?
Sent from my GT-N7100 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
Not sure. Im guessing the problem because im using the tmobile note 2. I did read through the DN3 posts and someone got theirs to work...

weedmon21 said:
Not sure. Im guessing the problem because im using the tmobile note 2. I did read through the DN3 posts and someone got theirs to work...
Click to expand...
Click to collapse
I don't think your tmobile note 2 is causing the failure. My i317 also have this problem.
I tried different MJ5 but still failed at the same way and also after I flash the DN3 4.4 for , my the baseband will become unknown.

[Q] Note 8.0 N5100 root problem

Hello,i recently got Note 8.0 N5100 with official 4.2.2 and i decided to root it. I used CF-Auto-Root and followed instructions, downloaded newest drivers and everything went well in odin 3.07 but after odin finished i got stuck wirh samsung galaxy note logo and nothing happens now.
what shall i do now, can anybody please help me!!!!!!!
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CF-Auto-Root-espresso10rf-espresso10rfxx-gtp5100.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> recovery.img
<ID:0/003> NAND Write Start!!
<ID:0/003> cache.img
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Removed!!
<ID:0/003> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
Problem solved. I exidently when i was using search in cf auto root website downloaded wrong cf file for p5100 instead of n5100.

miloslavc said:
Hello,i recently got Note 8.0 N5100 with official 4.2.2 and i decided to root it. I used CF-Auto-Root and followed instructions, downloaded newest drivers and everything went well in odin 3.07 but after odin finished i got stuck wirh samsung galaxy note logo and nothing happens now.
what shall i do now, can anybody please help me!!!!!!!
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CF-Auto-Root-espresso10rf-espresso10rfxx-gtp5100.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> recovery.img
<ID:0/003> NAND Write Start!!
<ID:0/003> cache.img
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Removed!!
<ID:0/003> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
Problem solved. I exidently when i was using search in cf auto root website downloaded wrong cf file for p5100 instead of n5100.
Click to expand...
Click to collapse
Your not the only one who had this problem... I which the mod would shut down the thread pushing rooting via flashing.
Too many newbies are having issues flashing.
I recommend saveroot.zip. It leaves your device's counter untouched. Also it is 100% safe.
Now what to do with your device since it is stuck at the Samsung logo.
You can do what I do for stuck screens. Power on, and hold only the up volume key. Keep it held until boot screen is finished.
If that does not work, go into recovery and clear cache and reboot.
If none of the options work, you may have flashed with an incompatible file, there are three versions and only one is specific to your device. you can try re-flashing with a good file.

saveroot
Hello,
I am having a heck of a time finding this. Would you please point me in the right direction?
Thx!
gooberdude said:
Your not the only one who had this problem... I which the mod would shut down the thread pushing rooting via flashing.
Too many newbies are having issues flashing.
I recommend saveroot.zip. It leaves your device's counter untouched. Also it is 100% safe.
Now what to do with your device since it is stuck at the Samsung logo.
You can do what I do for stuck screens. Power on, and hold only the up volume key. Keep it held until boot screen is finished.
If that does not work, go into recovery and clear cache and reboot.
If none of the options work, you may have flashed with an incompatible file, there are three versions and only one is specific to your device. you can try re-flashing with a good file.
Click to expand...
Click to collapse

[Q] [solved] i9195 - doesn't work mobile network and wifi

Hi guys,
after a lot of problem with my s4mini now the phone doesn't call and doesn't active the wifi connection. I've tried to flash all the modem i found, but every time the process is concluded with a fail (in odin)...
So i don't know i can i do.
Thanks to all
Atlantis

Try flashing a complete new firmware with Odin.

RoyaLKurTx3 said:
Try flashing a complete new firmware with Odin.
Click to expand...
Click to collapse
I tried many times but evrytime the process ends with a fail... Odin lets me flash only te recoverys...

atlantis87 said:
I tried many times but evrytime the process ends with a fail... Odin lets me flash only te recoverys...
Click to expand...
Click to collapse
Tell me all the steps that you are doing. And if you can, provide me some screenshots.

RoyaLKurTx3 said:
Tell me all the steps that you are doing. And if you can, provide me some screenshots.
Click to expand...
Click to collapse
Everything starts wit a mistake. I had CM snapshot 12 and i tried to flash the stock rom. Probably i wrong the version of the stock firmware. When the process ends with a fail the phone was softbriccked... I tried many things (exactly i don't remeber every thing i done...) and at the end th only way i found was to flash a new recovery. After that i flash CM12 but when i turn on the phone all the mobile connection (network and wifi) don't work... I tried to flash a lot of different modem but no one works...
I attach the screenshot of the dowload mode...
Thanks

atlantis87 said:
Everything starts wit a mistake. I had CM snapshot 12 and i tried to flash the stock rom. Probably i wrong the version of the stock firmware. When the process ends with a fail the phone was softbriccked... I tried many things (exactly i don't remeber every thing i done...) and at the end th only way i found was to flash a new recovery. After that i flash CM12 but when i turn on the phone all the mobile connection (network and wifi) don't work... I tried to flash a lot of different modem but no one works...
I attach the screenshot of the dowload mode...
Thanks
Click to expand...
Click to collapse
hi man try this :1 instal a custom CWM....2 enter to recovery mode 3-wipe data factory and wipe cach..3 format dalvik cach 4 format system and format modem...5 enter to odin mode 6 flach your stock rom 7 enjoy

Hi man. I have already tried step 1 2 3. Do you know how can i format statemi and modem? Thanks

atlantis87 said:
Hi man. I have already tried step 1 2 3. Do you know how can i format statemi and modem? Thanks
Click to expand...
Click to collapse
ok men 1 go to recovery 2 go to mounts and storage 3 format system 4 format modem 5 fomat cache.and after this flash your stock rom

ok, i tried and....
nothing
when i try to flash something odin answer the row below...
<ID:0/003> Removed!!
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> modem.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> NON-HLOS.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> Transmission Complete..
<ID:0/003> Now Writing.. Please wait about 2 minutes
<ID:0/003> Receive Response from boot-loader
<OSM> All threads completed. (succeed 0 / failed 1)
But... a question... in the download mode the last row is "WRITE PROTECTION: ENABLED"... Can influence somthing this thing??
Thanks

Be careful when you format system, it's dangerous and the only fix for it is flashing a ROM.
Try these:
1. Download this and extract the files in the ZIP: http://www.sammobile.com/firmwares/download/40040/I9195XXUCNK4_I9195OXXCNK5_SEE.zip/
2. You should get 2 files;
I9195XXUCNK4_I9195OXXCNK5_I9195XXUCNK4_HOME.tar.md5
SS_DL.dll
Ignore the SS_DL.dll. You will use the other file.
3. Go to Odin and thick only 'Auto Reboot' and 'F. Reset Time'. Now Insert the .tar.md5 I named above in the AP place.
4. Turn off your phone and boot into recovery. Clear data and cache. Now restart to download mode.
5. If you are asked to continue or to cancel and restart phone, choose continue.
6. Keep your phone like that and check that you have this (or similar) layout in Odin;
Now press start and wait until everything have finished and your phone boots (May take 8-11 minutes) If you followed these steps and you got a fail, then you must have done something wrong or your phone has something wrong in terms of hardware. Good Luck mate.

atlantis87 said:
ok, i tried and....
nothing
when i try to flash something odin answer the row below...
<ID:0/003> Removed!!
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> modem.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> NON-HLOS.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> Transmission Complete..
<ID:0/003> Now Writing.. Please wait about 2 minutes
<ID:0/003> Receive Response from boot-loader
<OSM> All threads completed. (succeed 0 / failed 1)
But... a question... in the download mode the last row is "WRITE PROTECTION: ENABLED"... Can influence somthing this thing??
Thanks
Click to expand...
Click to collapse
put your rom file in odin in (ap)....you can download your rom from sammobile.and try again try the metode up

RoyaLKurTx3 said:
Be careful when you format system, it's dangerous and the only fix for it is flashing a ROM.
Try these:
1. Download this and extract the files in the ZIP: http://www.sammobile.com/firmwares/download/40040/I9195XXUCNK4_I9195OXXCNK5_SEE.zip/
2. You should get 2 files;
I9195XXUCNK4_I9195OXXCNK5_I9195XXUCNK4_HOME.tar.md5
SS_DL.dll
Ignore the SS_DL.dll. You will use the other file.
3. Go to Odin and thick only 'Auto Reboot' and 'F. Reset Time'. Now Insert the .tar.md5 I named above in the AP place.
4. Turn off your phone and boot into recovery. Clear data and cache. Now restart to download mode.
5. If you are asked to continue or to cancel and restart phone, choose continue.
6. Keep your phone like that and check that you have this (or similar) layout in Odin;
Now press start and wait until everything have finished and your phone boots (May take 8-11 minutes) If you followed these steps and you got a fail, then you must have done something wrong or your phone has something wrong in terms of hardware. Good Luck mate.
Click to expand...
Click to collapse
Hi,
i tried also this... Odin says:
<ID:0/003> Removed!!
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> modem.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> NON-HLOS.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> Transmission Complete..
<ID:0/003> Now Writing.. Please wait about 2 minutes
<ID:0/003> Receive Response from boot-loader
<OSM> All threads completed. (succeed 0 / failed 1)
... i'm little bit disperate...

You inserted a modem.tar.md5 not the file I told you.

atlantis87 said:
Hi,
i tried also this... Odin says:
<ID:0/003> Removed!!
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> modem.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> NON-HLOS.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> Transmission Complete..
<ID:0/003> Now Writing.. Please wait about 2 minutes
<ID:0/003> Receive Response from boot-loader
<OSM> All threads completed. (succeed 0 / failed 1)
... i'm little bit disperate...
Click to expand...
Click to collapse
dont be afraid my friend this is simple...so dont put the file in the modem pit it at (ap) colone...try a difirent odin v 3.09 okey ..dont missed to extract the zip file for your file rom okey and gry again

RoyaLKurTx3 said:
You inserted a modem.tar.md5 not the file I told you.
Click to expand...
Click to collapse
Sorry, i wrongly paste the odin row... The follow row are the correct...
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9195XXUCNK4_I9195OXXCNK5_I9195XXUCNK4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> aboot.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

atlantis87 said:
Sorry, i wrongly paste the odin row... The follow row are the correct...
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9195XXUCNK4_I9195OXXCNK5_I9195XXUCNK4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> aboot.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Try everything again on a different computer, if you can.

RoyaLKurTx3 said:
Try everything again on a different computer, if you can.
Click to expand...
Click to collapse
Ok, thanks... i made all these trial on a macbook using vmware fusion with windows 8. I can try on another mac (with vmware and windows 8)... Do you think that can be work with another mac or is necessary to try with a pc?

atlantis87 said:
Ok, thanks... i made all these trial on a macbook using vmware fusion with windows 8. I can try on another mac (with vmware and windows 8)... Do you think that can be work with another mac or is necessary to try with a pc?
Click to expand...
Click to collapse
Try using windows.

RoyaLKurTx3 said:
Try using windows.
Click to expand...
Click to collapse
i tried and.... it works! However wifi and mobile network don't work. Do you have any other suggestion?
Thanks

RoyaLKurTx3 said:
Try using windows.
Click to expand...
Click to collapse
Maybe i found something... My IMEI is null... and i don't have a backup...

[Q] Where can I find stock rom for SGH-M919 4.4.4?

I need to send this back in exchange or update. Have had sim card issues with 4 S4's now this being the 5th. With changing the sim cards many times.
So i need to format back to stock and send in.
Can't seem to find the rom or process to get it done with odin or w/e is needed

http://forum.xda-developers.com/showthread.php?t=2816508

Kriptik210 said:
http://forum.xda-developers.com/showthread.php?t=2816508
Click to expand...
Click to collapse
thanks can i use this with odin or clean install inside recovery?

Use Odin, will recommend full wipe if coming from custom rom.
Pp.

PanchoPlanet said:
Use Odin, will recommend full wipe if coming from custom rom.
Pp.
Click to expand...
Click to collapse
K its only going back to stock to send back to carrier. But you cant clean install with odin so it has to be done in recovery no?

Odin will clean install because you don't need a custom recovery to install, all recovery can do is reset.
Once you Odin stock after factory reset you loose root and you get stock recovery.
Pp.

PanchoPlanet said:
Odin will clean install because you don't need a custom recovery to install, all recovery can do is reset.
Once you Odin stock after factory reset you loose root and you get stock recovery.
Pp.
Click to expand...
Click to collapse
So factory reset via inside rom ?
Then odin flash stock
reboot
all done?

That should do it.
Pp.

Doesn't work for me
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> M919UVUFNH7_M919TMBFNH7_M919UVUFNH7_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
and it wouldn't let me do it in recovery either

Try latest nk2 firmware, otherwise you will need a pit file to fix it.
Pp.

I eventually found a pit and still got this
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> M919UVUFNK2_M919TMBFNK2_M919UVUFNK2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
Click to expand...
Click to collapse
*edit
didn't see that last post but i just tried it and still an error so what now
trying using the following
M919UVUFNK2_M919TMBFNK2_M919UVUFNK2_HOME.tar.md5
M919UVUFNH7_M919TMBFNH7_M919UVUFNH7_HOME.tar.md5

AHHHH I SEE NOW
In Odin up top it shows what phone it is. I flashed a rom and it was not my carriers but I9505 S4
So how to I get the roms i just posted to flash over this to make it back to a T-Mobile variant?
This is the specs I am on if it helps
Baseband
M919UVUFNK2
Kernel
3.4.105-GoogyMax3_GE5-v1.2.7
[email protected] #26

PanchoPlanet said:
Try latest nk2 firmware, otherwise you will need a pit file to fix it.
Pp.
Click to expand...
Click to collapse
I'm familiar with the files for: the modem (modem.bin) and the LTE modem/or WiFi driver (non-hlos.bin); but I'm not familiar with a pit file. What is a pit file?