hi everyone,
I have a problem with my GALAXY WODER I8150 a CM10 alpha 4.1, it stuck on loading screen, before the problem occur I downloaded the "COMBINE MODS MODEL-1" for CM10 alpha 7.. after I boot it and flash using CWM it only run trough loading screen and it always stuck..
I tried to reflash it using ODIN and used the firmware of my phone afterwards my phone still stuck on Loading screen
Please help me with this
thanks
try go to recovery mode and
1. wipe cache
2. go to advance and /format dalvik cache
emmerson00 said:
hi everyone,
I have a problem with my GALAXY WODER I8150 a CM10 alpha 4.1, it stuck on loading screen, before the problem occur I downloaded the "COMBINE MODS MODEL-1" for CM10 alpha 7.. after I boot it and flash using CWM it only run trough loading screen and it always stuck..
I tried to reflash it using ODIN and used the firmware of my phone afterwards my phone still stuck on Loading screen
Please help me with this
thanks
Click to expand...
Click to collapse
Of course it will still be stuck, you didn't clean the mess in your /system folder. ) You now have 2.3.6 and 4.1 having wild fun over there.
So, I assume, at this point, you have the stock ROM, with the stock recovery. So, what I suggest is that you read the little tutorial below and follow it exactly as it was written.
1. Download CWM for Samsung Galaxy Wonder from here. (It's also available in the development section here.)
2. Flash it via ODIN, by following exactly the same steps as for the ROM flashing.
3. Enter CWM and:
clear data (factory reset)
clear dalvik cache (under "advanced" menu)
go back one step and under "mounts & storage menu -> select "format /system" option. This step is crucial for a clean install!! Especially when changing Android versions.
under the same menu, go ahead and format /sdcard. (Be careful NOT to format /external_sd !)
At this point, you can choose if you want to flash the Samsung stock ROM again via ODIN or flash CM10 again (If you choose to flash CM10, I would suggest the latest version).
Now, if you want to reinstall the stock ROM:
4. exit from there and put your phone into Download Mode again (Home button + Volume DOWN + Power Button).
5. flash the stock ROM via ODIN
If you want to reinstall CM10:
4. go back to the main screen in CWM
5. go to "install zip from sdcard"
6. browse to the location of your CM ROM and flash it
7. flash the correct Gapps for your ROM
8. reboot
That's all. Good luck!
just wanna add one more thing in the end, if u wanna re install cm10 then install the alpha7 version so u can apply the combined mod which will work only on cm10 alpha7
Related
Hello friends,
We all love Custom ROMs. Proof of brilliance of Developers on XDA. Many people don't know the correct way of flashing ROM and face various errors during or after ROM flashing. Even most advanced users can face such errors and need to troubleshoot their device.
Since I have been reading a whole lot of such issues here I decided to open a thread to troubleshoot such issues with help of everybody here. So lets get started.......
Before we start
I am trying to help you with best I can (with good experience) and shall not be responsible for any damage you do to your device.
Before flashing anything to your device read, read and read a lot about your device in your device forum especially about
How to recover device from Soft-brick
Bootloaders
Recoveries
Next download most recommended Stock firmware for your device to Computer.
Most important thing here is Bootloader (although most of the times you don't need to touch it at all). This thing can Brick your device . Be very very very cautious about flashing it. Don't if it is not absolutely necessary.
How to flash a Custom ROM
- If you are a new comer (Welcome)
1. Download and install Samsung USB drivers to your PC. Reboot. Connect your phone and check your phone is recognized.
2. Download ODIN 3.09
3. Download PhilZ Recovery 5.15 (Most recommended Recovery right now)
4. Open ODIN. Put Recovery tar.md5 file in PDA tab. Only "F.Reset" will be TICKED and nothing else.
5. Switch Off phone.
6. Put Phone into download Mode by pressing and holding "Vol down + Center (Home) key + Power On"
7. Now connect phone to PC. It will install drivers for your phone. In ODIN it will show connected as Yellow Box with some number.
8. Hit START.
9. After few seconds it will show PASS.
10. Remove your device.
11. Remove battery from phone. Re-insert battery.
12. Now press and hold "Vol Up + Centre (Home) key + Power On". You will enter in Recovery. Congrats :good:
13. Now Reboot System. If it asks if you want to disable Recovery Flash, hit Yes (otherwise on next boot Stock Recovery will come back)
- if you already have Custom Recovery
1. Place the ROM that you want to flash on SDCard (External is recommended)
2. Boot into Recovery
3. a) If you have PhilZ recovery
- Go to Wipe Data/Factory reset
- Clean to install new ROM. Thats it.
b) If you are on TWRP or CWM
- Format all these : /system /data /cache /preload /dalvik-cache
4. Flash the ROM
5. Don't reboot. Clear cache and dalvik cache and then reboot. (not necessary but recommended)
If you need to flash some MOD or OTA update after ROM flashing then
1. Flash the ROM after data wipe
2. Don't reboot to ROM
3. Reboot back to Recovery
4. Flash MOD or Updates
5. Clear Cache and Dalvik cache
6. Reboot System (ROM)
Enjoy the Brilliance of Awesome Developers at XDA :good:
Custom ROM flashing Issues and Solutions
Issues and Solutions:
Aroma installer freezes while flashing ROM or at the end of flashing
Use PhilZ Recovery 5.15. PhilZ v6 is reported to be having issues with Aroma.
Stock Recovery comes back after flashing PhilZ (or any) Recovery in ODIN
Follow the above mentioned method as it is and your problem will be solved. Actually Samsung Stock firmware checks Custom Recovery on reboot and re-write it with Stock recovery. That's why the above mentioned process. It will remove the script (install-recovery.sh) that does it.
I am on MK4 or MKD bootloader. Now what?
If you have flashed Official OTA or MK4 Stock firmware then you are on MK4 or later bootloader which is NOT DOWNGRADABLE (you can't flash any prior dated bootloaders like MJ5). Doing so can permanently brick your device. Although you can flash any Custom ROM that you want and should not face any issues.
Based on your reported issues I will keep updating this thread.
thank you very much for the great help
Apologize for the simpleton question/layout but it's been awhile since I did this to a rband new tablet and wanted to make sure I have it down right before proceeding.
1. Install Samsung USB drivers
2. Root tab following these instructions: http://forum.xda-developers.com/showthread.php?t=2661198
3. Install CWM follwoing these instructions: http://forum.xda-developers.com/showthread.php?t=2666232
4. Download CM11 ROM and GAPPS from here: http://forum.xda-developers.com/showthread.php?t=2666246
5. Copy CM11 ROM and GAPPS to Msd card
6. Boot into recovery (CWM)
7. Factory reset and Dalvik wipe
8. Install CM11 and GAPPS via CWM
9. Reboot
Did I miss anything?
vexille said:
Apologize for the simpleton question/layout but it's been awhile since I did this to a rband new tablet and wanted to make sure I have it down right before proceeding.
1. Install Samsung USB drivers
2. Root tab following these instructions: http://forum.xda-developers.com/showthread.php?t=2661198
3. Install CWM follwoing these instructions: http://forum.xda-developers.com/showthread.php?t=2666232
4. Download CM11 ROM and GAPPS from here: http://forum.xda-developers.com/showthread.php?t=2666246
5. Copy CM11 ROM and GAPPS to Msd card
6. Boot into recovery (CWM)
7. Factory reset and Dalvik wipe
8. Install CM11 and GAPPS via CWM
9. Reboot
Did I miss anything?
Click to expand...
Click to collapse
Make a backup of your stock ROM after step 6
jmill75 said:
Make a backup of your stock ROM after step 6
Click to expand...
Click to collapse
but be aware that that recovery cannot be cleanly restored at this time.
The custom recovery is still very valuable - for installing CM11, and for getting ADB access to the device in recovery mode.
But a restore will need to be accompanied by a factory reset to get the stock OS to boot again, or an Odin reflash of the stock image. My take on it is that the android_secure files cannot be backed up by CWM as of now.
Anyone planning on flashing a ROM might consider downloading the stock image for their device before they start, IMO.
hi
i am newbie and i am trying to install kitkat rom provide by restless from the link below:
http://forum.xda-developers.com/gal...-10/rom-100-stock-4-4-2-kitkat-p5200-t2866066
I am using Philz recovery and below is procedure i am doing.
1) copy rom to SDcard.
2) boot into recovery
3) wipe cache
4) wipe davrt
5) wipe for new installation rom
6) select install zip and then select the zip file and install the rom
after the upgrade/update and rebooting the tab is stuck at samsung logo.
I will really appreciate any help
thanks
Bump
Same thing happened to me when reverting back to 4.2.2.
Hold down pwer and volume up to get into recovery . Do a factory reset. Then boot to sytem. Worked for me.
Hi everyone
Sorry in case of repost.
I have a P5210 (Samsung Tab 3 Wifi). Once rooted everything was allright until I entered in recovery mode from the Rom Toolbox app.
I'm now stuck in a recovery loop mode and can't get out (CWM v6.0.4.7)
I've tried everything from factory reset / cache and dalvik cache wipe, to "fix" zips and so on. But nothing changes.
I've tried to reinstall CWM by putting a recovery image into a script and flash it through CWM. Seems to be done correctly, but when I reboot, it's still the same CWM (no update)
Eventually, i've tried to install some custom ROMs to start fresh : Every installation crashes at "WRITING SYSTEM PARTITION". I get black screen and a reboot.
And I've tried every custom Rom compatible with P5210.
Can you help me to get back to a clean configuration ?
N.
nicobee75 said:
Hi everyone
Sorry in case of repost.
I have a P5210 (Samsung Tab 3 Wifi). Once rooted everything was allright until I entered in recovery mode from the Rom Toolbox app.
I'm now stuck in a recovery loop mode and can't get out (CWM v6.0.4.7)
I've tried everything from factory reset / cache and dalvik cache wipe, to "fix" zips and so on. But nothing changes.
I've tried to reinstall CWM by putting a recovery image into a script and flash it through CWM. Seems to be done correctly, but when I reboot, it's still the same CWM (no update)
Eventually, i've tried to install some custom ROMs to start fresh : Every installation crashes at "WRITING SYSTEM PARTITION". I get black screen and a reboot.
And I've tried every custom Rom compatible with P5210.
Can you help me to get back to a clean configuration ?
N.
Click to expand...
Click to collapse
Hi
It seems you were on kitkat rom which may have updated your bootloader to kitkat version. The CWM needs to be updated to work well with kitkat. I had similar problem with my SM-T210, and solved the problem after updating CWM as per this post for T210:
http://forum.xda-developers.com/showthread.php?t=2433853
Your tab is different from mine so i think you need a fresh stock rom install using odin, then find an updated CWM for your tab.
I am trying to flash cm12.1 to my samsung galaxy grand duos, i have installed it before flawlessly. I flashed stock rom (jellybean 4.1.2) and now every time i install cm12.1 and gapps and then reboot the device, it shows the Samsung galaxy grand duos logo but is stuck on that. I have waited for it, in fact i have left it overnight and still was on that screen. I am using cwm, i have formated file system, cleared cache and dalvik cache.
PLEASE HELP! I HATE THE STOCK ROM!!
xNexeon said:
I am trying to flash cm12.1 to my samsung galaxy grand duos, i have installed it before flawlessly. I flashed stock rom (jellybean 4.1.2) and now every time i install cm12.1 and gapps and then reboot the device, it shows the Samsung galaxy grand duos logo but is stuck on that. I have waited for it, in fact i have left it overnight and still was on that screen. I am using cwm, i have formated file system, cleared cache and dalvik cache.
PLEASE HELP! I HATE THE STOCK ROM!!
Click to expand...
Click to collapse
Bro i think According to Installation guide of CM 12.1 No. 2 "If you were on CM 10.1 or a stock ROM prior to 4.2, upgrade to stock 4.2 first." and "Does not work on 4.1 stock ROM's bootloader, please upgrade to stock 4.2 before flashing".
I hope this will work:
1. Download stock firmware (4.2) Here (choose your region)
2. Download Odin 3.0+
3. put your phone into Download Recovery Mode (Volume down + Home + Power)
4. then flash your downloaded stock ROM (4.2) ' Keep in default setting
5. Reboot
6. Install Custom Recovery ( I assumed that your phone is already in the STOCK ROM 4.2)
7. Reboot into Custom Recovery (Volume up + Home + Power)
8. Perform Wipe Data,cache,dalvik
9. Then Flash/Install CM 12.1
10. Flash/install GAPPS
11. Reboot.
DONE!
Don't forget to hit thanks.
So i just basically flash stock 4.2.2 and then flash cm12.1 with gapps?
ill try it in a few minutes ^_^
dreyedison said:
Bro i think According to Installation guide of CM 12.1 No. 2 "If you were on CM 10.1 or a stock ROM prior to 4.2, upgrade to stock 4.2 first." and "Does not work on 4.1 stock ROM's bootloader, please upgrade to stock 4.2 before flashing".
I hope this will work:
1. Download stock firmware (4.2) Here (choose your region)
2. Download Odin 3.0+
3. put your phone into Download Recovery Mode (Volume down + Home + Power)
4. then flash your downloaded stock ROM (4.2) ' Keep in default setting
5. Reboot
6. Install Custom Recovery ( I assumed that your phone is already in the STOCK ROM 4.2)
7. Reboot into Custom Recovery (Volume up + Home + Power)
8. Perform Wipe Data,cache,dalvik
9. Then Flash/Install CM 12.1
10. Flash/install GAPPS
11. Reboot.
DONE!
Don't forget to hit thanks.
Click to expand...
Click to collapse
Oh my god!!!! Thank you! After so long someone helped