[Q] Samsung Galaxy Pocket S5300L - About xda-developers.com

Hi all xda.
Well, I need some help from the experts, I have a terminal i got a S5300L Latinamerican version i think and flashe few days ago, since then the home screen where it says the terminal model it's desapear, only error 'Logo_LTN_L.jpg' draw failed is showed, now I need to know if any of you know how to fix it, where I have to put the image folder or do I need to restore it and if out there will have some link to the stock rom of my phone how to put it again o something else that i have to do, thanks for your help, and sorry for my english.

Related

I Need Immediate Help Please!!!!

i was upgrading to that new htc rom using the free cid unlock method.
i kept doing it but i kept getting that vendor id error.
then i ran the bat one more time and the screen on my dash went white.
then i ran the ruu and it was like at 50 percent but i didnt know that it was actually installing so i opened the task manager on my pc and i closed it.
then i rebooted the phone and it just stays in a htc screen.
and i didnt have the htc rom, i had the rogers rom.
so i realized it WAS installing while on the white screen and i shouldnt have cancelled it.
so now idk what to do.
is it bricked?
can someone help me please.
flash it again from the bootloader mode
can you give me threough the process please?
or can anyone help me on how to do this through any instant messenger?
im a noob at this
For future reference "noob's" have no place flashing firmware with uncertified firmware and procedures. One should read up fully on what to do if it fails before going at it.
Just a note
merwin said:
For future reference "noob's" have no place flashing firmware with uncertified firmware and procedures. One should read up fully on what to do if it fails before going at it.
Just a note
Click to expand...
Click to collapse
sorry mister a+ certified-senior-know-it-all-member
bootleg16 said:
can you give me threough the process please?
or can anyone help me on how to do this through any instant messenger?
im a noob at this
Click to expand...
Click to collapse
turn it off. hold camera key for three seconds and press power button.

Bricked Samsung Blackjack i600v - PLEAS PLEASE HELP

Hey Guys, so I have done the stupid thing and flashed my samsung blackjack i600v with the update from samsung.com WM6 (think made for the i607). The phone starts up normally displaying the green WM6 screen and goes into the At&t (orignally vodafone) screen, runs across the screen says goodbye and swtiches off. Sometimes if i press buttons and try and make it think i can get to the home screen but then again, it turns off. Any possible ways that I can flash it back or make it work again?
Anything, a program, tools how on earth do you format a mobile phone back to normal.
Any help or direction on this would be greatly appreciated you have no idea.
Many thanks
Kam
Anyone? please help..even if its to say that the phone is not able to be fixed.
thanks
Can You get into bootloader?
If You can - You need to find a full i600 ROM with Radio part and flash it.
Edit: Here is a LINK - check it - there's a link for ROM also
Hi there, I can turn it on n get it into bootloader mode, it says AT&T bootloader! But it's not being recognized by the computer, what is this radio part? I have downloaded theb ROM!
Thank u

[Q] Help me, need the next step in my diagnostics.

Alright, I just recently bought a new Galaxy S3, through Rogers in Canada.
I was successfully rooted and flashed w/ a custom rom.
I then downloaded "VZW GS3 EZ-Unlock (Bootloader)", so I could escape Error Status 7 in CWM while trying to flash a new rom...
Boom, phone doesn't turn on. I guess it wasn't compatible w/ my i747.
If I connect to the PC, the sound when a device is connected plays. If I try and boot to download (3key combination), the sound just repeats (off/on). But the device doesn't turn on. Screen stays blank.
So, I just finished making a 300K ohm usb jig.
This doesn't make the phone turn on either.
So, how do I flash a bootloader in SDMode ?? I read it involves jumping a resistor -- I'm assuming this is the next step I have to take to try and revive my phone. What's the file I need on my sdcard? Who can point me in the right direction?
----
Edit:
Bump::
URGENT!
Can someone PLEASE use QPST and in the Software Downloader program, make a backup from a stockish i747 Rom, upload it, and link me!?
I'm sure I've figured out a way to restore my device!! This will help the whole community since several ppl are having my identical issue.
It looks like you brick your own phone...you should return to the store where you got it from and get replace one. Also, you shouldn't put bootloader b/c it is 100% chance to brick it. 2nd thing is that you need very new version of CWM (v6) which it is found in the thread b/c it happen to me when I have very old one and got same status.
The USB jig should be 301k I do believe. Bootloader mishaps usually need JTAG repair to get functional. mobiletechvideos I think is the name I keep seeing around here. Good luck.
Bump::
URGENT!
Can someone PLEASE use QPST and in the Software Downloader program, make a backup from a stockish i747 Rom, upload it, and link me!?
I'm sure I've figured out a way to restore my device!! This will help the whole community since several ppl are having my identical issue.
Boot_loader.hex
I'm also looking for a hex file of the default boot loader for i747... if anyone knows, that's greatly appreciated
I don't know if you can do it that way - probably not.
In all likelihood you've bricked your phone and it requires a physical modification to work. Software won't do it.
Instead of flashing some strange boot loader you should have just updated your recovery - a quick search and a little reading would have told you that was the cause of the status 7 error.
Sent from my SAMSUNG-SGH-I747 using Tapatalk 2

[Q] Please Help Samsung Galaxy Tab 3 Flickering Screen!

hello i was wondering if there way anyone out there how could please help me with this screen flickering problem i have tried using clock work recovery i have used odin and reset my device a good 6 times today everything works fine its just the screen in flickering non stop no matter what i do it wont work but when i put it into download mode the screen is fine and on the start up when it says "Samsung Galaxy Tab 3" the screen is fine but it only is flickering when the device boots up can someone please help me i just received this as a gift for christmas and barely got any use out of it thanks you can contact me on my email it would be very appreciated :[email protected]
bigdaddywelker1 said:
hello i was wondering if there way anyone out there how could please help me with this screen flickering problem i have tried using clock work recovery i have used odin and reset my device a good 6 times today everything works fine its just the screen in flickering non stop no matter what i do it wont work but when i put it into download mode the screen is fine and on the start up when it says "Samsung Galaxy Tab 3" the screen is fine but it only is flickering when the device boots up can someone please help me i just received this as a gift for christmas and barely got any use out of it thanks you can contact me on my email it would be very appreciated :[email protected]
Click to expand...
Click to collapse
Can make a picture, how it looks when its flickering and post this.
For me it looks like that is an bootloader Problem !!!
Have you testet when your go back to real stock, i mine flash stock Firmware with Odin , is that solved ????
Flickering screen
bierma32 said:
Can make a picture, how it looks when its flickering and post this.
For me it looks like that is an bootloader Problem !!!
Have you testet when your go back to real stock, i mine flash stock Firmware with Odin , is that solved ????
Click to expand...
Click to collapse
How can I go back to real stock and un root this device I have the same problem. I only got it today and I am desperate
bsquirrell said:
How can I go back to real stock and un root this device I have the same problem. I only got it today and I am desperate
Click to expand...
Click to collapse
Take a look to the thread " unbrick and restore " from Tomsgt here you find a guide
galaxy tab 3 7
I have finally managed to fix the flickering screen by re installing a new firmware. Odin 3.07 wouldnt work, but odin 3.185 did for some reason!!! Now is there a root for this that won't put me in this position again. I am sure this has been asked and answered somewhere else, but I can't find it.
The previous root I did installed an old firmware, which caused the problem,
The auto display feature on this tablet still leaves the screen too dark,so I have had to disable this feature. Anny ideas anyone, thank in advance for any help
bsquirrell said:
I have finally managed to fix the flickering screen by re installing a new firmware. Odin 3.07 wouldnt work, but odin 3.185 did for some reason!!! Now is there a root for this that won't put me in this position again. I am sure this has been asked and answered somewhere else, but I can't find it.
The previous root I did installed an old firmware, which caused the problem,
The auto display feature on this tablet still leaves the screen too dark,so I have had to disable this feature. Anny ideas anyone, thank in advance for any help
Click to expand...
Click to collapse
Go to dev Thread and usw the thread Cwm for sm-t210/r
http://forum.xda-developers.com/showthread.php?t=2433853
I had the same issue when i was stuck on boot loop, install a different recovery, i used CWM, and then install a different rom. Allot of the stuff here works across different platforms and it works fine but sometimes it cause the flicker.... good luck
I think you went into the developer options and clicked on the show screen updates. It will flicker all the time until you disselect it.
Sent from my SM-T210 using xda app-developers app

I think my Phone is hardbricked?!

Hey there
Let me tell what happened...
A few days ago i got my Cell Phone back from the Cops, they had taken it to save proofs for a crime i didnt do and i had to take it back from the Department.
Now i gave my autogram and got it back but it won´t turn on
I cannot enter CMW Recovery, neither Download mode
Arrived at home i found out that it connects to the PC and answers to me that i need a QHUSB_DLOAD Driver... so i got this and i read in some Forum that i need to geht QPST...
so now i have qpst and the driver so its identified as Com9 on my computer.... but at this point i don´t have any idea what to do.... Someone in here who had the Same Problem or someone in here who can help me?
The Phone is an Samsung Galaxy S4 Mini Serranoltexx GT-1595
Please help me
Greets
Any Ideas? Please!
Now i downloaded an Debrick Image tryin to fix my phone and wrote it with Win32DiskImager on my SDcard (16gb)
put it into my Smartphone and pressed the Power button but nothing happened....
Whats the Cure for this? i´m loosing all my nerves
May Somebody help me?

Categories

Resources