Bricked Samsung Blackjack i600v - PLEAS PLEASE HELP - Upgrading, Modifying and Unlocking

Hey Guys, so I have done the stupid thing and flashed my samsung blackjack i600v with the update from samsung.com WM6 (think made for the i607). The phone starts up normally displaying the green WM6 screen and goes into the At&t (orignally vodafone) screen, runs across the screen says goodbye and swtiches off. Sometimes if i press buttons and try and make it think i can get to the home screen but then again, it turns off. Any possible ways that I can flash it back or make it work again?
Anything, a program, tools how on earth do you format a mobile phone back to normal.
Any help or direction on this would be greatly appreciated you have no idea.
Many thanks
Kam

Anyone? please help..even if its to say that the phone is not able to be fixed.
thanks

Can You get into bootloader?
If You can - You need to find a full i600 ROM with Radio part and flash it.
Edit: Here is a LINK - check it - there's a link for ROM also

Hi there, I can turn it on n get it into bootloader mode, it says AT&T bootloader! But it's not being recognized by the computer, what is this radio part? I have downloaded theb ROM!
Thank u

Related

Phone is freezing while starting

Hello,
I've just installed HardSPL succesfully, after that I wanted to install MightyRom 4.6, so I did. That went succesfully too according to my computer. Now when i want to switch the phone on, it keeps hanging with the T-Mobile picture on it. I've done a hard reset for several times and also a few soft resets. I also took my battery out for a few minutes, but when I switch it on, the same thing happens.
Please help me out of this !
Ps. sorry for my bad english !
for taking a little stress from your brain take an other rom - orig. rom from your provider.....
(go bootloder from pda; if your orig. rom only one *.exe-file you have to extract (winzip/winrar) it before flashing; connect usb (bootloader screen change from serial to usb); than flash)
but before you do this, how long you have to wait and look to your screen?
it can be sometimes a very long time until a windows-screen is coming.
if your pda gets hot than dont wait and flash asap new rom.
after 5 minutes waiting without any changes you have to flash an other rom.
I think I may have the same problem with my Diamond. I also installed MightyRom 4.6. Now, when I power up my phone, I get through the RGB stage to a white backdrop with instructions in blue to push volume button up for a reboot to manufacturers settings or push volume button down to reboot to manufacturers settings and wipe the movinand....after I select either one, when it gets to the HTC logo (HTC Diamond in white on a black background), it freezes. My pc won't recognise my phone when I plug it in...
Do I now have a really gorgeous paperweight or can I hold my Diamond to my ear again? Insight into my problem would be much appreciated.
By the way, XDA Dev rocks. Thanks to all who made this site possible.
Brick or no brick ?
Oh, I forgot to mention that my phone was a non-branded HTC running a Duttys rom. I did not want to get a DOPOD Diamond from China Mobile as they cost more and I dunno if they put Big Brother software in there.
HateMan01 said:
I think I may have the same problem with my Diamond. I also installed MightyRom 4.6. Now, when I power up my phone, I get through the RGB stage and then when it gets to the HTC logo, it freezes. My pc won't recognise my phone when I plug it in...
Do I now have a really gorgeous paperweight or can I hold my Diamond to my ear again? Insight into my problem would be much appreciated.
By the way, XDA Dev rocks. Thanks to all who made this site possible.
Click to expand...
Click to collapse
hi try and do like okokur has posted
cobbs said:
hi try and do like okokur has posted
Click to expand...
Click to collapse
My pc won't recognise my phone when I plug it in...
HateMan01 said:
My pc won't recognise my phone when I plug it in...
Click to expand...
Click to collapse
do you have it in the boot loader before you plug it in to your pc?
Brickety brick, brick, brick...
My phone does not recognize my pc and vice versa. I tried plugging the phone in before booting it up. I tried while booting up. I tried at the white screen stage...nothing...help...
It also doesn't stay at the RGB screen for long...maybe 2 seconds...
Please break it to me gently if I have killed my HTC...I don't want to start drinking again...
...
My phone is a GSM Diamond. MightyRom 4.6 is for CDMA. If I combine the two(like I did) then am I screwed?
Can someone please give me some insight, please? I have been scouring the net for 3 days non stop now and my eyes are going to explode...
What is Jtag and can your average home user use it? Is it hardware or software...?
Cobbs: I assume when you say bootloader you mean something other than the RGB screen,,,cos as I stated in my first post, my phone does not stop on the RGB screen...

O2 atom life upgrade help needed i read everything to this point!

Hey guys.
Im trying to upgrade my O2 Atom life from WM 5 to the latest O2 official 6.5 WM ROM.
When i tried updating normally by connecting my phone to computer and running the rom setup... my upgrade process gets stuck at Stage 4 with 0%.
If i put my phone in bootloader screen and then upgrade, i get Customer and model ID error.
After reading this forum I tried changing Pass.32 file properties from WWE to CHT and still i get the same customer and model ID error.
I even tried uploading those two files al1.dio and ext rom to a mini sd and upgrade through bootloader that doesn't seem to work either.
Can someone please guide me what else can be done step by step.
Thanks alot in advance for helping.
Ps - im using latest Windows Device center with windows vista.
hey
hey guys... please help... my WM5 keeps shuttin off by itself... really need to upgrade. thanks.
hey
hey guys... any help would be appreciated.... my phone turns off on its own and then when i click power on.. it goes straight to DSUU white screen and has to be factory reset so can't really deal with it.. please help upgrading would help.
Have you read here?
http://wiki.xda-developers.com/index.php?pagename=HTC_Atom
Hope it helps and good luck,
hey
hey sorry. yeh i have read that page... nothing helps me there... ok so i got my phone upgraded somehow to the latest 6.5.... but i'm facing same problem.. whenever phone turns off or restarts it goes straight to DSUU white screen.. and the only way to come out of it is by ressetting the phone to factory by pressing record + power button n pressing the hole.... to restart.
not sure whats wrong with it.
Have you asked on atom section?
perhaps there you can have more chances
hey
hey.
yeh i will post it there as well... people don't really respond nowadays!

How to flash my HTC Touch pro 2 (sprint)

Hi everyone well I'm new to the flashing and dont want to jump any steps as this could possible brick my phone...
I've been having some problems with flashing as i cant find a step by step to flashing my HTC TP2. I've managed to do the RhodiumW Hard-SPL package but after trying to flash to some custom RUU's the installation seems to go fine its not until the phone first boots up, that's when the phone just hangs on the HTC splash screen
From there i cant do anything other then boot up to the tricolor bootloader screen and re-install the original 2.04.651.4 update!
can someone tell me what im missing to be able to flash my HTC correctly, or at least point me in the right direction?
Thank you in advance!!!
step 1
http://member.america.htc.com/download/RomCode/HTC Touch Pro2 (Sprint)/HTC Touch PRO2 MR1.exe
step 2
http://rhodiumw.htc-unlocks.com/hard-spl.php
step 3
http://www.mightyrom.com/mightyrom/touch-pro-2/
Hey Tommy many thanks for the post. I just upgraded my phone and peeling through the information overload, however you direct link does not work for step 1. I want to make sure that I am running the correct piece of software that you recommending. Could you please list the title for that file?
Nevermind I was able to find it via a mirror site.
Back into lurker status for now
Thanks
alright so i was able to install they mightyrom on my phone that went well my phone didnt freeze and everything started the way it should have.
but does that mean i can now flash my phone to other for example "leo cell" or Bxsteez Rhodium" if not how do i get to that point cuz when ever i flas them to they just freese on the white splash screen with the HTC logo in green letters!!
Thanks!
If you have installed Hard SPL then use the sd card method.
1. Format the sd card FAT32 ( they come FAT default) and copy the rom's .nbh file onto it. Rename to Rhodimg.nbh .
2. Insert sd card back into powered off Rhodium. Go into bootloader by pushing down volume and power.
3. If you did it properly and Hard SPL is on your phone then it should say to press power to update os...
If you aren't sure if you have Hard SPL then go to bootloader without the sd card in there, it should say SPL - 0.85.Olinex if you have Hard SPL, anything else won't register the flash file.
Cheers...
OK I was able to update to Winmo 6.5 with no issues....but here is my questions with regards to the Rhodium_W Hard-SPL
I was attempting to run it and it never gets pass 0%...In reading the details of the install instructions it reads
"the device needs to be connected to Activesync or WMDC via USB cable. and it must not be in Flight/Airplane mode (i.e. the phone part should be on).
3) internet access is required as the program checks online for updates and for the license."
Click to expand...
Click to collapse
I have yet to activate my phone with Sprint could this be my error that I need to active my phone? I wanted to have the phone flashed and customized before activating.
signalsoldier said:
OK I was able to update to Winmo 6.5 with no issues....but here is my questions with regards to the Rhodium_W Hard-SPL
I was attempting to run it and it never gets pass 0%...In reading the details of the install instructions it reads
I have yet to activate my phone with Sprint could this be my error that I need to active my phone? I wanted to have the phone flashed and customized before activating.
Click to expand...
Click to collapse
I think you should ask this in the hard spl thread in the cmda section...That is the place for those questions Assuming that you have a cdma phone because you did not mention it. Otherwise check the hard spl thread in the gsm section.
Heading that way thanks for the directions mate!
Alright so ive been able to flash my rom to my first custom rom by energy which i like very much, although still a noob, i want to flash it to a different rom
What is the best way to flash to a different rom with out leaving any files behind that would affect the new rom?!
do i have to do a hard reset or something that would clear my phone from any old files?!
htcru7 said:
Alright so ive been able to flash my rom to my first custom rom by energy which i like very much, although still a noob, i want to flash it to a different rom
What is the best way to flash to a different rom with out leaving any files behind that would affect the new rom?!
do i have to do a hard reset or something that would clear my phone from any old files?!
Click to expand...
Click to collapse
Just flash away
LOL alright thanks i guess im just paranoid but thanks i'll "flash away"
Lock
When you start Rhodium_CDMA_HardSPL_V1_10R3_100HSPL stoppers on 0%.
I removed the firmware via mtty 1.42 entering the command: task 28 \ task 29. Ie fully formatnul system. This is often applied to remove the lock on the HTC 6800. At this time nothing worked. Under bootloger any firmware stoppers on 0%. Besides, even the official RUU_Rhodium_W_S2_Sprint_WWE_2.04.651.4_RS_2.32.00WF_NV_SPCS_2.20_0224_PRL60660_S
hip
and HTC Touch PRO2 MR1 from the official portal hangs at 1%, then is restarted Device, and as expected if there is no OSes lit logo HTC ...
What should I do?? If GSM is blocked, how do I remove it to flash?
Ps Is it possible to disable the lock on the firmware via mtty
1.42??
Thank you very much for your answer!
Scream-krg said:
When you start Rhodium_CDMA_HardSPL_V1_10R3_100HSPL stoppers on 0%.
I removed the firmware via mtty 1.42 entering the command: task 28 \ task 29. Ie fully formatnul system. This is often applied to remove the lock on the HTC 6800. At this time nothing worked. Under bootloger any firmware stoppers on 0%. Besides, even the official RUU_Rhodium_W_S2_Sprint_WWE_2.04.651.4_RS_2.32.00WF_NV_SPCS_2.20_0224_PRL60660_S
hip
and HTC Touch PRO2 MR1 from the official portal hangs at 1%, then is restarted Device, and as expected if there is no OSes lit logo HTC ...
What should I do?? If GSM is blocked, how do I remove it to flash?
Ps Is it possible to disable the lock on the firmware via mtty
1.42??
Thank you very much for your answer!
Click to expand...
Click to collapse
the Hard-SPL will only work if you booted windows mobile. you have to sync the phone in windows mobile to the PC.
is there other way to get through in hard spl because i dont have any account for example, paypal...... http://media.xda-developers.com/images/icons/icon9.gif
chrisjavier666 said:
is there other way to get through in hard spl because i dont have any account for example, paypal......
Click to expand...
Click to collapse
Hard SPL is free for non-commercial users.
my tp2 is bricked
i tried to upgrade my htc touch pro 2's rom. i received error 226 and anytime i switch it on, it gets to the tricolor boot and displays a lot of info and says try again. Can anyone please help me?
nastyrock said:
i tried to upgrade my htc touch pro 2's rom. i received error 226 and anytime i switch it on, it gets to the tricolor boot and displays a lot of info and says try again. Can anyone please help me?
Click to expand...
Click to collapse
Did you try flashing the stock ROM? It's always a good idea to try that if you think there's no hope. It flashes everything.
Also, did you try task29?

[Q] Rookie Mistake

Hi I have and IMATE PDA2k EVDO and I tried a d-two rom and I now have the device sitting on the 4 color screen every time I reset it. Any idea how I reset it back to defaults so I can load another image onto it, I have the original image. any advice would be appreciated.
Thanks,
Actually I just fixed it.
Anyone know of any WM5,6 or 6.5 roms that work on this phone. The EVDO network is dead here in Australia so I just want to convert it into a PDA.
For the love of God... if you are going to make a thread saying "Hey guys, I broke this, how do I fix it?" Do not EVER update with "I fixed it!" without telling us HOW you fixed it.
I thought it was such simple fix it did not requiere explaination. To enter the bootloader you do the following
Press Power + record (above the volume slider) + softreset at the same time.
This puts it into the load mode so you can reflash.
problem with my xda iis
hi nid help... i followed the instruction on how to upgrade my ppc but it seems that the download link for win 6 does not exist anymore and now im stock in the boot loader i think the screen only shows "serial and below shows v2.07" i cant use my phone anymore i tried to reset it and emove the battery but stil it only shows serial... hope you can help me guys tnx...godbless
jayreyes_31 said:
hi nid help... i followed the instruction on how to upgrade my ppc but it seems that the download link for win 6 does not exist anymore and now im stock in the boot loader i think the screen only shows "serial and below shows v2.07" i cant use my phone anymore i tried to reset it and emove the battery but stil it only shows serial... hope you can help me guys tnx...godbless
Click to expand...
Click to collapse
about WM 6 rom, maybe you can look at ftp://ftp.xda-developers.com/BlueAngel/Shipped_Complete_Updates/
or at http://shipped-roms.com/index.php?category=windows mobile&model=Blue Angel
try to flashing rom again
You sir are an idiot.
A Blue Angel rom will not work for a Harrier.
So delete your comment because some other idiot will follow your bad instructions then **** up their phone and make another idiotic post.
Yea so did anyone figure out this whole problem with the white boot loader screen? I'm no where near a programmer or anything but I think my boot loader version is out dated. My HARRIER, not blue angel, is stuck at a white screen that reads Serial(USB when connected to usb of course) and v1.02. I've had a Harrier before this and it had the four color screen for boot loader. Am I on to something here?
Oh btw I already tried to reflash the rom over and over but updater keeps saying it can't connect.
jayreyes_31 said:
hi nid help... i followed the instruction on how to upgrade my ppc but it seems that the download link for win 6 does not exist anymore and now im stock in the boot loader i think the screen only shows "serial and below shows v2.07" i cant use my phone anymore i tried to reset it and emove the battery but stil it only shows serial... hope you can help me guys tnx...godbless
Click to expand...
Click to collapse
I have the same problem, anyone found a fix?
yes I have too same problem..plz help
i have a problem
Obviously.
But which one?
Tell us as elaborate as possible.
Problems Blue Angel Harrier Alpine
B-44 said:
Obviously.
But which one?
Tell us as elaborate as possible.
Click to expand...
Click to collapse
Please be careful: This is a Blue Angel (BA) Thread!
As Hima and Alpine Fora are closed, i will try to help as well as possible,
but please post marked "off topic"- hope moderators won't intervene...
And always first work out which device you're talking about.
Still love Alpine...
@admin: I know it's quite impossible to keep all these legacy threads alive- but what about some rescue thread, e.g. for non-touch-screen-phones,the Hima-BA-Family?
As i know from Siemens/BenQ Phones, it has gone silent around here, but from time to time some collectors appear which shouildn't be left alone.

samsung s5230 stuck on phone lock

hi guys,
i got a samsung s 5230 (toco lite), and it is stuck on phone lock when i turn it on.
is there a way,where i connect it to usb to get the code with a program.
or if i hold down ( down volume,camera,power button) the phone turns on,it wont go to the down load screen/ unless i am doing it wrong?? so i dont know if i can re flash this phone.
thank-you if you can help me!!
-minty- said:
hi guys,
i got a samsung s 5230 (toco lite), and it is stuck on phone lock when i turn it on.
is there a way,where i connect it to usb to get the code with a program.
or if i hold down ( down volume,camera,power button) the phone turns on,it wont go to the down load screen/ unless i am doing it wrong?? so i dont know if i can re flash this phone.
thank-you if you can help me!!
Click to expand...
Click to collapse
you forget pattern/pin or what ? the easy way is to flash again by Odin
keep things as simple as possible I suppose you do not have important data on phone if so just flash again !
Would you have a link to the latest flash files please.
-minty- said:
Would you have a link to the latest flash files please.
Click to expand...
Click to collapse
read on this thread
or just search here (enter 5230 as search string)
you need to subscribe to get access to download link
also you have flashing tool and tutorial on this site search for it !
http://www.sammobile.com/firmware/?page=1&t=2
cheers guys, i found a flash.
now when i started the flash the battery fell out.
have i buggered up the phone????
can i repair it somehow?
please can you help me..
thanks.
-minty- said:
cheers guys, i found a flash.
now when i started the flash the battery fell out.
have i buggered up the phone????
can i repair it somehow?
please can you help me..
thanks.
Click to expand...
Click to collapse
-flash again by Odin check if you can enter recovery/download mode by keys
-when your phone is starting you should see a samsung/android logo this is botloader image..if you can't see it phone is bricked it means bootloader is affected and you need service tools to repair bootloader
never flash it without checking battery status at least 50% and use a laptop on battery to avoid power surge problems
Samsung s5230 is run properiatly os so you cannot use odin, but you can use mulitloader program to flash stock firmware to your phone.

Categories

Resources