Related
I've used many different kinds of screen protectors in the past, and this time I tried XtremeGuard which I found on eBay. The cost was only $2.50 shipped. I must say hands down, this is the best screen protector I have used.
Other kinds I've used in the past were a thin hard plastic, kind of like a clear overhead sheet, but thinner and sticky on one side. These were not good IMO, because they make the touchscreens less sensitive and since they were hard, the edges would start to peel first and it would be all downhill from there.
The XtremeGuard is a more stretchy film material, kind of like 3M clear bra, or the kind you would find on a car. Its got a nice grippy rubber feel to it, which I actually like. Its "softer" so it sticks better to the screen.
I used a mild soapy water solution to put it on, and at first was kind of concerned with my results. Some areas were cloudy, there were some visible bubbles and when the screen was on it looked all rainbow cuz of the water trapped inside. After a couple days though, all the moisture evaporated, the cloudiness cleared up and all the bubbles were gone. I was left with a perfectly crystal clear screen that adhered all the way around, even on the edges. You would not be able to tell there was a screen protector on here (I have the OEM HTC silicone skin that covers the edges as well so you can't see the edge of the screen protector). The touchscreen works perfectly, and the screen protector does not interfere at all.
The screen protector was the exact size of the screen, perfect cut. Which is good, but makes it challenging to install, if you're off by a tiny bit, the screen protector will stick off the screen and that will be prone to peeling up later on. So take your time during the install to ensure its on there straight and perfectly. I started from the top where the speaker is and lined it up around those lines, and used a credit card to press it down and get as many bubbles out as I could. If this is your first time installing a screen protector, I would suggest getting 2-3 to make sure you get it right. At only $2.50ea, you really can't go wrong here. I'm 100% satisfied.
http://cgi.ebay.com/NEW-XtremeGUARD...ewItem&pt=PDA_Accessories&hash=item35a9e73eed
I would also like to note that I do not work for, or am in any way affiliated with XtremeGuard at all. I simply tried their product, and I liked it, so I'm leaving my feedback here.
I have tried it, but it is like a mm to long on top to bottom. And it was like 2mm to short in width.
That was my experience. Could be wrong for everyone.
I like mine, it fits perfectly. Doesn't stick over the edge and covers the whole thing. Mine was a perfect fit, not too long or short on any sides.
I'll try to get some pics up later when I get the chance
Man, I want to order it so bad, but with Otterbox covers around the corner, I think its a little waste of money.. :S
Any tackiness or stickiness with this protector? I'm currently using Phatom Skinz and love it, but I'm always looking around for something that may potentially be even better...especially with a price like this. How about orange peel?
thanks,
Alan
There is a very slight tackiness with this screen protector, but I actually like it. It gives a good feel when typing. It might interfere with pong or some other games where you need to move your finger really fast, but that doesn't really apply to me.
No orange peel, or any peeling at all for that matter.
The cloudiness really bugs me. The Zagg I had did not cloud like this one does.
The item from ebay is too pricier. This site offers products with much lower price and free shipping world wide. The 3 packed screen protector is much cheaper than 1 packed from ebay.
http://www.geartaker.com/product/3x...opers&utm_medium=minqing&utm_campaign=FA0070B
this 3 packed protector was once sold at $0.01 during its 2nd super deal.
Hey guys, I recently bought one of these off Amazon when I ordered my Otterbox case, it was only $2 so I figured I had nothing to lose. Here's my take on it.
http://forum.xda-developers.com/showthread.php?p=19109961#post19109961
I was wondering if there are any go to screen proctectors? Any to avoid, like do any cause issues with the touch screen?
Sent from my Galaxy Tab!
I'd avoid the hard plastic static-type. They're difficult to put on without dust. I've been using the ones from clearprotector (.com). 50% off and free ship with the code iwantultra (have it memorized cause I've gotten several). The corners and edges are kind of a ***** to get on, but they work well and come with a lifetime warranty (or so they say...). This is a wet-application so don't use them unless you're willing to take the time to watch the youtube videos to learn how to install, and then takes about 20 minutes to install.
I get mine from www.bestskinsever.com. I've had no problems with them. The screen protector is easy to apply and very durable.
I have Ghost Armor on mine and like it, it is a bit smoother than Zagg or Bestskinsever.
Be warned if you want the full body protection, adding this to the back of my tab caused me to have the newton ring problem. I never had the problem with just the screen protector on, I should I have just stuck with the screen and not the entire thing but I really wanted the matte back on my tab.
Thanks fellas. I have and used to do/use the wet application ones for a while. Then I got tired of them and just went with the cling ones. I think I'll get the wet app and it should last a longgg time. Especially since Im not going to be using the tab every day.
I went with Clarivue on the recommendation of a friend.
It's decent enough, no tackiness or anything like that but it's not the best fitting, could've been a couple of mm wider and taller.
Other than that, whilst I've had a long-standing dislike for them, recently I've found Zagg's InvisibleShield protectors to be pretty decent - they seem to be very well fitted and the tacky feel to them that I remember doesn't seem as noticeable.
Kinda wish I'd gone with them for my Tab
Which would you guys say offers the smoothest screen experiences of all? I don't care about longevity as I only use my tab about once every 2 weeks
Imo the smoothest would be the cling on ones.
Sent from my Galaxy Tab!
I purchased these in July from Amazon. http://www.amazon.com/gp/product/B0058NXPLK
I was never a fan of the "wet" applications, to me it just seemed like too much work and I was never comfortable spraying any type of liquid all over my devices, regardless of how harmless they might be.
But anyway, this is a clear, non-matte protector that is the "static cling" kind of application. Once it goes on properly, you cannot see that is even there. The touch feeling is the same as if you had no protector on. I really feel that those matte ones, while they do reduce sun-glare, a lot of them provide a "tacky" feeling that maybe is fine for a smaller screen such as a phone, but can become very annoying for a larger screen if you do a lot of swiping across the larger surface area of a tablet. But that is a personal thing....I usually don't use my tablet outside in the bright sun anyway, so the matte types are useless for me.
I've had it on since the end of July and it's held up very well. You do have to wipe the smudges off the screen occasionally, but you'd have to do that anyway even with no protector. I'm extremely satisfied with these.
So I've got an Invisible Shield en route for my Tab, will post back when it arrives.
Same here haha.
Sent from my Galaxy Tab!
I just bought the glare-reduction screen protector from BodyGuardz. Has anyone else had any experience with them? I wanted something that would offer a decent amount of protection for the screen (fingerprint and physical pressure), but also not reduce the touch sensitivity at all. (I type with the tip of my nose since I can't use my fingers, and trying to press too hard hurts )
Not sure where you can get it, but here in Singapore there's a brand called DataFlex and their screen protectors seem really good.
I bought SGP steinheil shield ultra optics. I liked it.
Raistlin1 said:
I have Ghost Armor on mine and like it, it is a bit smoother than Zagg or Bestskinsever.
Be warned if you want the full body protection, adding this to the back of my tab caused me to have the newton ring problem. I never had the problem with just the screen protector on, I should I have just stuck with the screen and not the entire thing but I really wanted the matte back on my tab.
Click to expand...
Click to collapse
So this newton ring issue is a major problem. What if I just protect the back and leave the screen open? I have the new logitech keyboard case on the way and the front is protected in the case, but the back is exposed. I planned on protecting the back only. But I wont do anything if it'll case the newton rings.
Newton Ring?
nuprotocol said:
So this newton ring issue is a major problem. What if I just protect the back and leave the screen open? I have the new logitech keyboard case on the way and the front is protected in the case, but the back is exposed. I planned on protecting the back only. But I wont do anything if it'll case the newton rings.
Click to expand...
Click to collapse
Yeah. Same here. Just want a more "grippy" back. How does one produce Newton Rings from the back of the device. Methunked it was a display issue resulting from the interaction of the protector and display glass...kinda by definition...
Hopefully we'll find out soon. I just want to protect the back.
skeeter123 said:
Yeah. Same here. Just want a more "grippy" back. How does one produce Newton Rings from the back of the device. Methunked it was a display issue resulting from the interaction of the protector and display glass...kinda by definition...
Click to expand...
Click to collapse
I blame the install of the rear skin because I had the screen skin installed first and then three weeks later I had the rear done. He turned the tab face down and installed the skin. When he turned it over, bam, Netwon Rings...
I never had them before the front screen protector, during the front screen protector install or after the front protector was on the Tab.
Will it happen to you? I have no idea but from what I have read about the problem it is caused because of the Tab moving/flexing which can be caused by excessive heat and certain handling of the Tab.
thanks!
Raistlin1 said:
I blame the install of the rear skin because I had the screen skin installed first and then three weeks later I had the rear done. He turned the tab face down and installed the skin. When he turned it over, bam, Netwon Rings...
I never had them before the front screen protector, during the front screen protector install or after the front protector was on the Tab.
Will it happen to you? I have no idea but from what I have read about the problem it is caused because of the Tab moving/flexing which can be caused by excessive heat and certain handling of the Tab.
Click to expand...
Click to collapse
Thanks for taking the time to explain the details. Sounds like a warranty kinda thing mebbe. Hope it gets resolved! Mine is on order and I'll watch out for this issue.
Cheers!
slack04 said:
I'd avoid the hard plastic static-type.
Click to expand...
Click to collapse
I bought an anti-glare protector from Cellularbuy on eBay and managed to get it on in one go with no dust at all. The protector fits perfectly and the camera and light sensor holes line up spot on. The anti-glare makes the screen look a little grainy, but I hear that even the Steinhell ones that are many times more expensive have the same problem.
This has been gone over millions of times on each forum here, but here's how I did it:
-Wipe the screen down with a soft cloth and glasses cleaner or isopropyl to get any grease off
-Run the shower in a small bathroom on hot until the room is unbearably steamy
-Put on a hat to keep your hair and head funk from falling on the screen
-Line the protector up on the screen before removing the film and tape it on one side with a few pieces of Scotch tape
-Also make a "handle" out of tape to put on the top of the protector opposite the taped-down end. This will help with alignment
-Go into the bathroom and clean the screen with a good microfiber cloth. Also clean the front and back protective sheets on the film so there's no dust to come off when you start peeling them. The steam should be enough to wet it. Take one final look
-Peel the protector back and lay it down pulling the taped edge taut to keep it lined up
-Smooth any bubbles out with a credit card BEFORE peeling the top sheet off
IF you do have any dust, use a piece of tape on a corner to lift up the protector and another piece of tape to pick up the dust. If the room is steamy enough and you did a good job of wiping the screen this shouldn't happen.
Hello all,
I am looking for some advice on the SPIGEN Screen Protector Steinheil (Ultra Fine or SQ Crystal Clear). My main concern is too keep the spen as precise as possible, as if im using it bareback. I have seen the Zagg Invis on some of my friends and tried it and I just dont like the drag, rubbery feeling and scratch like marks it leaves.
If it helps I do alot of art work and sketches, i just can't drag a Cintiq around.
Any thoughts would be great.
Thanks.
codeflight said:
Hello all,
I am looking for some advice on the SPIGEN Screen Protector Steinheil (Ultra Fine or SQ Crystal Clear). My main concern is too keep the spen as precise as possible, as if im using it bareback. I have seen the Zagg Invis on some of my friends and tried it and I just dont like the drag, rubbery feeling and scratch like marks it leaves.
If it helps I do alot of art work and sketches, i just can't drag a Cintiq around.
Any thoughts would be great.
Thanks.
Click to expand...
Click to collapse
I have the Spigen SPG Ultra Fine. The install was easy. I do screen installs in my bathroom with the shower on hot so that the humidity is up. It prevents dust from floating in the air.
The screen went on easily, smoothed out easily, and looks great. The smudge / finger print resistance is great so far and the pen works with no issue aside from the traces of what you wrote being left on the shield. It wipes off though.
But you can definitely see what I'd call a chalk-like outline on the screen after using the pen so regularly cleaning will be necessary with this shield.
I have a ultra fine on my n7k and its nice. Held up good so far 8 months down the road. .
Sent from my GT-N7000 using Tapatalk 2
it's definitely less rubbery than Zagg, if you don't like any drag, change your wacom pen nib to the pure white one. It's dam smooth with it.
The ultra fine isnt even close to zagg in the way it feels....
Sent from my GT-N7000 using Tapatalk 2
tokendog said:
I have the Spigen SPG Ultra Fine. The install was easy. I do screen installs in my bathroom with the shower on hot so that the humidity is up. It prevents dust from floating in the air.
The screen went on easily, smoothed out easily, and looks great. The smudge / finger print resistance is great so far and the pen works with no issue aside from the traces of what you wrote being left on the shield. It wipes off though.
But you can definitely see what I'd call a chalk-like outline on the screen after using the pen so regularly cleaning will be necessary with this shield.
Click to expand...
Click to collapse
As meticulous as I am, I made all precautions for adhering the Spigen Clear protector. Cleaned my surroundings in the bathroom, washed my hands, Steamed the room with fogged mirrors, and closed door and STILL static and dust particles!! The more I tried, the more dust there was! I gave up about a half hour later with about 30 dust particles under the protector. Plus, those small adhesive strips they provide to a terrible job in removing dust from the back side of the protector. Years ago, I bought a Boxwave protector for my GF's Sony Clie TH55. Obviously a smaller screen, but no problem what so ever and NO precautions necessary. $22 down the drain which is too much for a piece acetate with adhesive. Probably cost pennies to make. The printing and assembly of the product box probably cost more.
For big screens like this one, you guys should get wet apply protectors.
I got Xtremeguardz, and they're amazing. No dust, and I switched the pen tip to one of the plastic one so there's no residue and it flows smoothly.
Sent from my SGH-T989 using Tapatalk 2
theking_13 said:
For big screens like this one, you guys should get wet apply protectors.
I got Xtremeguardz, and they're amazing. No dust, and I switched the pen tip to one of the plastic one so there's no residue and it flows smoothly.
Sent from my SGH-T989 using Tapatalk 2
Click to expand...
Click to collapse
Thanks, if Spigen sends out an other one free of charge, then I'll take further precautions like wearing a hazmat suite IN the shower.
Just an update:
I went ahead and purchased the Ultra Crystal and the Ultra Fine. Both were very easy to apply I just followed this video on youtube. Since I cant post links just search this in youtube "Installation And Review Of Steinheil Screen Protector Galaxy Tab 10.1".
I applied the Ultra Fine on a Galaxy Tab and the Ultra Crystal on my Galaxy Note 10.1 both with ease.
To follow up the results of my original question about possible spen scratch marks.
Ultra Crystal: The black nib left no signs of scratch marks, though there was slight resistance.
Ultra Crystal: The white nib felt smooth and similar to bareback. But when I turned off the Note, I noticed marks everywhere. I tried to wipe it off and had no luck. Dissapointed at this point I tried to do more research on my desktop to find another screen protector. Approximately 30 minutes later I come back to my Note and lo' and behold the spen scratch marks were gone. I don't know if the protector has some self healing property but it is certainly different from the Zagg I have seen on my friends were the marks stayed.
As for fingerprints, the Ultra Crystal does pick up prints, were the Ultra Fine does not.
Codeflight, what's the quality of the ultra fine one like? I believe it is anti-glare or matte, so does it pixellate the screen or make it harder to read in any way? Must you turn up the brightness to compensate?
I got the ultra-fine (matte) a couple days ago and I'm pretty happy with it. I found the solid white plastic s-pen tip works much better than the black tip, and I've yet to notice any marks or scratches after a couple days of solid note taking. Like any matte screen protector, it diminishes the sharpness of the screen somewhat and requires a slight bump in brightness to compensate, but I read a lot of pdfs and the reduction in glare is worth it to me. I haven't noticed any pixelation or grain effect.
holgalee said:
Codeflight, what's the quality of the ultra fine one like? I believe it is anti-glare or matte, so does it pixellate the screen or make it harder to read in any way? Must you turn up the brightness to compensate?
Click to expand...
Click to collapse
Beetmonger has already posted, I have had similar experiences with the Ultra Fine, so in addition to your question about brightness, Yes I do have to turn up brightness a couple of notches.
codeflight said:
Just an update:
I went ahead and purchased the Ultra Crystal and the Ultra Fine. Both were very easy to apply I just followed this video on youtube. Since I cant post links just search this in youtube "Installation And Review Of Steinheil Screen Protector Galaxy Tab 10.1".
I applied the Ultra Fine on a Galaxy Tab and the Ultra Crystal on my Galaxy Note 10.1 both with ease.
To follow up the results of my original question about possible spen scratch marks.
Ultra Crystal: The black nib left no signs of scratch marks, though there was slight resistance.
Ultra Crystal: The white nib felt smooth and similar to bareback. But when I turned off the Note, I noticed marks everywhere. I tried to wipe it off and had no luck. Dissapointed at this point I tried to do more research on my desktop to find another screen protector. Approximately 30 minutes later I come back to my Note and lo' and behold the spen scratch marks were gone. I don't know if the protector has some self healing property but it is certainly different from the Zagg I have seen on my friends were the marks stayed.
As for fingerprints, the Ultra Crystal does pick up prints, were the Ultra Fine does not.
Click to expand...
Click to collapse
one review I read says there is no hole for the sensor?
wyou2 said:
one review I read says there is no hole for the sensor?
Click to expand...
Click to collapse
Yes. I can confirm that.
Using ultra crystal. Slightly more rubbery but love it after i change to the white pen nib.
One of the good screen protectors is the clearplex protector. Check it out here: http://clearplex.myshopify.com/coll...r-shield-guard-protector-skin-cover-case-note
thanks for the post kenny but the OP is asking specifically about the spigen. That clearplex is already in the "what is the best protector" thread.no need to hijack this one.
Does the ultra fine affects the sensor, since there is no hole for it?
Sigh. I think I'm just too sensitive. I found the Ultra Fine unbearably scratchy. I just installed the Crystal and it still feels pretty different from the bare screen. It's definitely rubbery, and whenever my stylus catches any dust particle it feels like I'm scratching sand onto the screen. Plus sometimes it even squeaks! Maybe I just can't have a protector if I'm using a stylus. I'm waiting for a Just Like Glass protector for my new Nexus 7, and if the stylus works on it I might just try one for the Note.
Sent from my GT-N8013 using Tapatalk 2
Update: 12/16/12
Been using this for 3 days and I'm very satisfied with it:
How it feels - It feels like touching a regular paper but smoother.
Spen tip - White tip
Big improvement: I can put my palm on the screen without zooming in on the note, I guess my palm slides a little on the glass surface causing it to zoom.
Screen doesn't look as dirty because of the finger prints.
Can read longer because the screen isn't too bright and glare is greatly reduced.
Overall I like it because it feels like writing on a paper rather than glass. I'm not really a fan of writing on glass and since I was little I've been writing on paper ^_^v
Original post:
Well I finally got my Ultra Fine and all I can say is wow. I had moko screen protector before and I've felt it restrict my fingers from doing swipes and forget about the spen. I took that moko screen off my note after 30 minutes from installation. The end result with any screen protector is subjective, but I do urge you guys to try Ultra Fine.
Install: Easy if you follow the directions. Orient your note "portrait" so the camera/sensor would be on your left side and the charging port will be on your right. clean with provided solution and towel. Peel off about 1~2 inches. Align it close to the edge from top and peel halfway let the screen protector adhere it self. double check for any dust particle then proceed installing to the rest of the tablet. Squeeze out the bubbles and check for dust particles. I had 1 dust particle and used the supplied tape to lift the edge and another tape to get the dust. So let me say it again. only peel off the backing halfway to reduce dust particle from getting between the screen and protector.
Spen - use the white tip and don't need to press to hard to write ^_^ it feels good writing.
Brightness compensation - Very Subjective. I like mine with cool feeling so that means dimmer.
Fingerprints - Reduced greatly.
I'll update with images.
The Ultra Fine sound amazing for stylus/art use; But how lacking is the visual quality of watching movies on netflix and such? I heard the brightness/sharpness is slightly degraded. I was wondering if you'd even notice after maxing out the the brightness? I don't normally do screens but this tablet is so awesome. Want to keep it that way.
Hi,
I'm launching this question mainly to those who use the Note for drawing with the S Pen.
Before the Note I had an Acer Iconia A500 and I chose a Matte screen protector and I think it was a good decision for that tablet. I used it a lot for watching movies while in the underground, bus or train and the antireflectiveness of the matt finish helped a lot with dark scenes. also, it was a good antifingerprints solution. The drawback was the clarity of the image suffered a little but not very much so it was ok.
Galaxy Note is a totally different matter. I will still be using it for watching videos, of course, but I bought it mainly for drawing and painting.
Being a Wacom Intuos user for more than 15 years, I've always loved the feel of the finish of Intuos surfaces trying to imitate the feel of paper. The finish is matt and it wears with the years so you have to replace it from time to time but you can perfectly live with a very scratched surface for a long time. Of course, over a screen, it is a different matter.
So, I would like to hear the impressions of artist who are using or have used their S-Pen over Matte and Clear screen protectors. Does the S-Pen leave marks on matte surfaces? Does it move more naturally?
I've been holding off on a screen protector for the same reason( but I do have a case with a cover already). I mainly use my Note 10.1 for sketching and drawing.
One thing I will tell you is that some screen protectors, such as the Zagg protectors have a sticky feel to them. I have one on my S3, and I tried using my stylus on it and it adds to much grip to the surface. I think any screen protector that has anti-glare properties but is not matte will have this problem.
Another thing to keep in mind is that even on a standard Wacom tablet the drawing surface gets worn but you just don't notice it because it doesn't have light coming through it.
Also a matte surface will not only show more wear quicker but will also wear down the nib in the stylus faster.
The areas where you draw the most will become shinny, compared to the rest of the surface, from the constant friction.
Matte screen protectors also lower the contrast ratio. It lightens the black areas to be more dark grey.And they slightly distort the picture.
I would think it would feel similar to a Intous. Right now the bare screen is too slippery for my tastes.
Would love to hear from someone who has a matte screen protector and uses their tablet for drawing or painting, but I think one day I'll just break down and try it myself.
P.S. you might want to check out another post I had about my modded S-pen. I bought one with an eraser and modded it to make it easier to hold the button down and bigger so it's easier to hold for extended periods.
http://forums.androidcentral.com/samsung-galaxy-note-8-0/278396-s-pen-alternative.html
jedikalimero said:
Hi,
I'm launching this question mainly to those who use the Note for drawing with the S Pen.
Before the Note I had an Acer Iconia A500 and I chose a Matte screen protector and I think it was a good decision for that tablet. I used it a lot for watching movies while in the underground, bus or train and the antireflectiveness of the matt finish helped a lot with dark scenes. also, it was a good antifingerprints solution. The drawback was the clarity of the image suffered a little but not very much so it was ok.
Galaxy Note is a totally different matter. I will still be using it for watching videos, of course, but I bought it mainly for drawing and painting.
Being a Wacom Intuos user for more than 15 years, I've always loved the feel of the finish of Intuos surfaces trying to imitate the feel of paper. The finish is matt and it wears with the years so you have to replace it from time to time but you can perfectly live with a very scratched surface for a long time. Of course, over a screen, it is a different matter.
So, I would like to hear the impressions of artist who are using or have used their S-Pen over Matte and Clear screen protectors. Does the S-Pen leave marks on matte surfaces? Does it move more naturally?
Click to expand...
Click to collapse
I have been using the clear screen protector and so far I like it. At first it didn't feel as smooth as without the screen protector so then I put the white touch leads included with the s-pen and it now feels smooth. I think Samsung included the white s-pen leads to use specifically with screen protectors. I haven't tried it on the matte screen protector but I think it will work fine.
smdexin said:
I have been using the clear screen protector and so far I like it. At first it didn't feel as smooth as without the screen protector so then I put the white touch leads included with the s-pen and it now feels smooth. I think Samsung included the white s-pen leads to use specifically with screen protectors. I haven't tried it on the matte screen protector but I think it will work fine.
Click to expand...
Click to collapse
Do you mean the leads that are fully made of hard plastic, not the ones made of plastic and rubber?
jedikalimero said:
Do you mean the leads that are fully made of hard plastic, not the ones made of plastic and rubber?
Click to expand...
Click to collapse
Yes those ones!
The courier delivered a tempered glass type protector from China this morning and I have some spare time to install it in the afternoon. This protector is actually a sample from the manufacturer and I have rejected several of them previously due to the poor placement of cutouts. I did not even bother installing them coz the cutouts were just so so misaligned and I doubt if they are for P600 while I am having a P605 (This is the reason the manufacturer gave although I wonder if the button placement are THAT different between P600 and P605).
This one should be the third one and it is reasonably fit for my P605. It doesn't have any indication on its thinkness and by the look of it I guess it's the common 0.05mm type.
In Short:
Pros:
- The protector is WAY*100 better than the traditional clear plastic protector I had on the P605.
- It's clear (oops... ). Crystal CLEAR!
- VERY smooth to write on with the S-Pen (NO more dragging by the plastic protector) This is the MOST important point! I can live with those traditional plastic screen protectors on phones / pads with no pens but with S-Pen I need a MUCH better writing experience. This is DEFINITELY a personal preference coz I am a fountain pen lover and has always been VERY demanding on writing surfaces.
- The edges of the protector and around area around the cutouts are smooth (but not those tapering curved ones as the one I have on my Note 3).
- I guess one does not need to worry about this protector in fear that it will scratch the screen if it is smashed coz I smashed the one on my Note 2 but it had caused absolutely no harm to the screen.
Cons:
- Obviously, expensive. Way more expensive than those plastic one yet it lasts longer.
- And there aren't too many manufacturers making tempered glass protector for P605. I guess may be the Note 10.1 2014 just isn't popular enough YET. The market is flooded with tempered glass protector for IPAD and Note III but not for P600/P605.
- Not AS resistant to scratches as you may think. The one on my Note III was scratched after three days and I still did not know why (Not with keys or sharp objects in the pocket but it was scratched). Er...a mystery huh.
- Not compatible with some cases.... especially those bumpers. I use a metal bumper on my Note III and it can't be "assembled" (The slot-type) due to the added thickness of the protector. On Note 10.1 2014, I use the original book case so NO problem so far. I would love to have a metallic bumper for my P605 tho. Still yet to find one.
- You can feel the WEIGHT of it. It adds a bit weight to the already-quite-heavy tablet .
- May be a bit difficult to install but I can say it's FAR FAR easier than installing the plastic one. Just do it slowly... don't rush it... then... OK!
The Installation and my experience with it
The installation is about the same as the way we install the plastic one tho it's a lot easier. There is a trick: peel the 1st layer (marked with a label) of the non-sticky film diagonally half way down and careful align the cutouts with the Home button and the sensors. After aligning them, pull the remaining half away from the corner underneath
and SLOWLY.... REMEMBER SLOWLY and SOFTLY put little pressure on it at the center. This will stick the protector onto the screen while not too strong that you can still move the protector around with your nails by pushing it on the sides. After inspecting closely that there is no dust and the alignment is perfect, just apply little force smoothly across the surface and peel off the blue film on the surface of the protector then ..........YEAH... your screen is now very well protected!
After playing it for about two hours now, what I like most is the smoothness when writing on it. Definitely unbeatable on this. I use the Samsung S-Pen Holder Kit on it and it turns writing and drawing on P605 even more enjoyable. I enjoy sketching on it.
Reflection may be a problem when reading... em...but I like the crystal clear screen a lot more now.
My Verdict on P605's accessories:
Emm... It is one of the best accessories I have bought so far for my P605.... I recommend getting a tempered glass protector and the Samsung S-Pen holder kit to my friends.
The original book cover is a short term solution until there are more options on the market (hope there will be)
I will DIY a leather case anyway during the holiday anyway
Photos of the protector are attached. You can see the edges of it are still 2-3mm away from the rim of the tablet. Macro photos showing the cut outs too.
** Update: The protector claims to have an Oleophobic coating yet it stills attract fingerprint quite easily. A gentle swipe with a clean cloth can clean it.
Mind sharing the link to buy this screen protector ?
Thanks
Sent from my SM-P605 using xda app-developers app
Sorry.. this one is not from an online store. It's a sample for my shop.