Develop Bugs

HTC DINC2 clocking/volting.

Hey everyone. What type of values do you prefer to run on the DINC2 when it comes to clocks/volts? I've searched and read that this CPU is similar to the Thunderbolt, and people on the thunderbolt tend to overclock it anywhere between 1.4-2.0 GHz. Can I get some general statistics/info here? I'm looking for safe/typical statistics for the following:
1) Minimum clock speed (underclocking, for those who do not like to mess with voltage)
2) Maximum clock speed on STOCK voltage (overclocking without messing with voltage)
3) Minimum voltage on STOCK Speed (undervolting)
I plan on running either CM7Kang or SRZ1.3 and am wondering what I could do with it.

I normally run SRZ1.3 rom with overclock to 1.4GHz using SetCPU and undervolt to -50 on all values using IncrediControl.
Get the pretty close to the same battery life as stock and most of my apps load a bit faster.

It all depends on your phone man, each is a little different, I can only go to 1.4 something ghz before my phone locks up but I've heard of others going much higher, I wouldn't set my Max speed any lower than 768 because of lag. I would under volt all values by 50, then set the 245 MHz value to 725 mil volts and use the smart ass v2 gov so when the screen is off it uses that speed and sips battery...
Sent from my Incredible 2 using XDA App

I know phones are different, but I just wanted to know a generic thing. 1.4 GHz is your typical OC on stock voltage? Sounds about what the Thunderbolt guys said.

I've had my phone extremely stable at 1.8, but battery life sucked. Currently, I'm running cm7 with voltages -50, governor set to ondemand, min 384, max 1.4. I do get a little bit of lag coming from unlocking screen. So i would say 700mhz would be a good minimum.

sjpritch25 said:
I've had my phone extremely stable at 1.8, but battery life sucked. Currently, I'm running cm7 with voltages -50, governor set to ondemand, min 384, max 1.4. I do get a little bit of lag coming from unlocking screen. So i would say 700mhz would be a good minimum.
Click to expand...
Click to collapse
700 min? I think that would drain battery like crazy...
Sent from my Incredible 2 using XDA App

Here's my setup. I'm running mikrunny with stock kernel, and stock voltages.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
And here's my battery level info.

tylerlawhon said:
Here's my setup. I'm running mikrunny with stock kernel, and stock voltages.
View attachment 864113
And here's my battery level info.
Click to expand...
Click to collapse
Run the same with -50mv
Sent from my ADR6350 using xda premium

I am running at 1.1ghz with -100 all. No reboots so far
Sent from my Incredible 2 using Tapatalk

kevdliu said:
I am running at 1.1ghz with -100 all. No reboots so far
Sent from my Incredible 2 using Tapatalk
Click to expand...
Click to collapse
How good is your battery life with that setup?

klabit87 said:
How good is your battery life with that setup?
Click to expand...
Click to collapse
60 percent after 7hr 30min. thats with 83 percent of the time no signal and one bar the rest.
Sent from my Incredible 2 using Tapatalk

Whic kernel are you on?
Sent from my ADR6350 using xda premium

faehsemc said:
Whic kernel are you on?
Sent from my ADR6350 using xda premium
Click to expand...
Click to collapse
I am running touchpro's ICS with aeroevan's v6 kernel here
if you decide to switch there is currently a market download bug with the combo. the solution is in the ICS discussion thread over at the general section.

kevdliu said:
I am running touchpro's ICS with aeroevan's v6 kernel here
if you decide to switch there is currently a market download bug with the combo. the solution is in the ICS discussion thread over at the general section.
Click to expand...
Click to collapse
U wrote 1.1 I wasn't thinking GHz I was thinking mikrunny 1.1 and was like damn.. never could get past -75mv
Sent from my ADR6350 using xda premium

im trying the -50 undervolt on condemned as we speak. 245/1209

I always oc to 1.3ghz, I am currently using the smoothass governor on aeroevans v6 ics kernel. I undervolt -25 across the board for AOSP roms and -50 for Sense roms. Currently running Touchpros ICS beta 3 build, Last night before I plugged in my phone I was at 67% after 16 hrs 32min. My phone runs silky smooth, no lag and very fast.

dankblaze said:
I always oc to 1.3ghz, I am currently using the smoothass governor on aeroevans v6 ics kernel. I undervolt -25 across the board for AOSP roms and -50 for Sense roms. Currently running Touchpros ICS beta 3 build, Last night before I plugged in my phone I was at 67% after 16 hrs 32min. My phone runs silky smooth, no lag and very fast.
Click to expand...
Click to collapse
so is -50 bad on a aosp rom?

mighty_markus12 said:
so is -50 bad on a aosp rom?
Click to expand...
Click to collapse
No I'm -75 on liquid and its awesome
Sent from my Incredible 2 using XDA App

mighty_markus12 said:
so is -50 bad on a aosp rom?
Click to expand...
Click to collapse
not necessarily bad but most of the time not needed due to less processes running all the time to suck battery like in a sense rom, it may work for people but it can lead to lagging and freezing when you undervolt too much.

Battery Saver Script - 6.30.12

Greetings all!
I have modified Calkulin's Battery Saver Script to work with our GNex devices. I updated the undervolt init.d script to work on both CPUs and tweaked the voltages based off Apex's voltage table. If you are setting cpu setting on boot via control app (ie: Glados, Franco, performance settings) please disable since the conflicting scripts will cause issues. The default governor and other settings can be modified by manually changing values within the scripts.
Prerequisites:
A kernel with init.d support
-default CM9 kernel doesn't work (still looking for a fix)
Flashing Instructions:
1. Reboot into recovery and make Nandroid backup
2. Flash attached zip file just like you would a rom.
3. Reboot and enjoy.
REMOVED FOR STABILITY/COMPATIBILITY
Undervolt Steps are based on # of CPU frequencies available:
Code:
STEPS_10="1475 1375 1325 1275 1225 1175 1050 975 850"
STEPS_9="1425 1375 1325 1275 1225 1175 1050 975 850"
STEPS_8="1375 1325 1275 1225 1175 1050 975 850"
STEPS_7="1325 1275 1225 1175 1050 975 850"
STEPS_6="1275 1225 1175 1050 975 850"
STEPS_5="1225 1175 1050 975 850"
CPU profiles:
Code:
BATTERY_PROFILE_1: From 100% - 85% battery level
MAX_CPU_SPEED="1200000"
MIN_CPU_SPEED="0"
BATTERY_PROFILE_2: From 84% - 0% battery level
MAX_CPU_SPEED="1000000"
MIN_CPU_SPEED="0"
AWAKE_GOVERNOR_ON: Changes to this initially after screen turns on
AWAKE_GOVERNOR="interactive"
AWAKE_MAX_CPU_SPEED=max profile speed
AWAKE_MIN_CPU_SPEED=max profile speed
AWAKE_DURATION="5"
SLEEP_GOVERNOR_ON: Changes to this once screen turns off if no SCREENOFFMAX file is found
SLEEP_GOVERNOR="conservative"
SLEEP_MAX_CPU_SPEED="800000"
SLEEP_MIN_CPU_SPEED="0"
The script at work.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
CREDITS:
98% of the credit goes to Calkulin -
bigxie for posting the voltage table
ME

I'll most def be giving this a shot.
D
Sent from my Sprint Galaxy Nexus CDMA using xda premium

installing
so i just flash threw recovery right? if i make a nandroid back up will it remove it if it makes my phone go crazy?

justro said:
so i just flash threw recovery right? if i make a nandroid back up will it remove it if it makes my phone go crazy?
Click to expand...
Click to collapse
yes
Sent From My Sprint Galaxy Nexus via XDA Premium

do I need to install anything else besides this .zip?
script manager?
setCPU??
anything?

Just installed combined with samurai kernal and let me say its pretty damn cool
Sent from my Sprint Galaxy Nexus CDMA using xda premium

broad_st_bully said:
do I need to install anything else besides this .zip?
script manager?
setCPU??
anything?
Click to expand...
Click to collapse
No, the script looks for those programs and deactivates itself. You should only run this script for cpu scaling.
Sent from my Sprint Galaxy Nexus CDMA using Tapatalk 2

justro said:
Just installed combined with samurai kernal and let me say its pretty damn cool
Sent from my Sprint Galaxy Nexus CDMA using xda premium
Click to expand...
Click to collapse
I just installed this combo. I'm using stock rom though. How's your bat life been?
Also are there any setting/options, I havent found any going through settings.

Is there a way to easily remove the script... another zip to flash perhaps? Or is a nandroid restore the only way?
In any case, thanks OP this looks good :thumbup:
Sent using Tapatalk 2

jten9 said:
Is there a way to easily remove the script... another zip to flash perhaps? Or is a nandroid restore the only way?
In any case, thanks OP this looks good :thumbup:
Sent using Tapatalk 2
Click to expand...
Click to collapse
You should be able to just delete the script from the init.d directory.

So far day one test and I'm loving the results so far
Sent from my Sprint Galaxy Nexus CDMA using xda premium

justro said:
So far day one test and I'm loving the results so far
Sent from my Sprint Galaxy Nexus CDMA using xda premium
Click to expand...
Click to collapse
Thanks looks about right to me.
Sent from my Sprint Galaxy Nexus CDMA using Tapatalk 2

Bradart said:
You should be able to just delete the script from the init.d directory.
Click to expand...
Click to collapse
Thanks, easy enough!
Another noob question- what is an easy way to verify that the script is running? I think its possible to check with Script Manager (smanager), can anyone point me to directions? I didn't come up with much from searching...
If it matters, I'm running Franco m3 and stock rom
Sent using Tapatalk 2

justro said:
So far day one test and I'm loving the results so far
Sent from my Sprint Galaxy Nexus CDMA using xda premium
Click to expand...
Click to collapse
What's your screen on time?
Sent from my Sprint Galaxy Nexus CDMA using Tapatalk 2

This is what I've got today. Much improved compared to the same usage before I was getting approx 6-7hrs if I was lucky.

will this work with stock rom + kernal

raisinbagel said:
will this work with stock rom + kernal
Click to expand...
Click to collapse
No, you must have a kernel with init.d support.
Sent from my Sprint Galaxy Nexus CDMA using Tapatalk 2

raisinbagel said:
will this work with stock rom + kernal
Click to expand...
Click to collapse
Sent From My Sprint Galaxy Nexus via XDA Premium

What kernel are you using?
Also with this work with franco and or samurai ? i keep switching back and forth not sure what one is better with black ice rom

cheddaface said:
What kernel are you using?
Also with this work with franco and or samurai ? i keep switching back and forth not sure what one is better with black ice rom
Click to expand...
Click to collapse
It causes reboots on Franco milestone 3
Sent from my Galaxy Nexus using xda premium

[KERNEL] ASDK 4.2.2 Reborn v2.0| 2013-04-23

{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
PRESENTS:
ASDK v1.0/ASDK Reborn v2.0
(All-Star Devs Kernel)
BIG THANKS TO AYYSIR FOR LETTING ME TAKE OVER!!
LEARNING as I go.
PLEASE keep thread CLEAN and on TOPIC.
ASDK 4.1.2
Features for 4.1.2 kernel version
Only for AOSP Roms running 4.1.2
Linux kernel 3.0.49
GPU clock to 320MHz
Governors (ABYSSPLUG, BADASS, SUPERBAD,LAGFREE, SLEEPY, SCARY,WHEATLEY, LAZY, ADAPTIVE, INTERACTIVE, PEGASUSQ, CONSERVATIVE, ONDEMAND, USERSPACE, PERFORMANCE)
Schedulers (CFQ, BFQ, VR, SIO, NOOP, DEADLINE, ROW, ZEN)
Overclocking & Undervolting
Max OC 1.9ghz (PLEASE DON'T OC TO 1.9 AND EXPECT IT TO BE STABLE THEN COME TO THE THREAD AND COMPLAIN)
Fast Charge
Voltage Control App included [Link to App Thread]
ASDK 4.1.2 Final
DOWNLOADS
ASDK-GS2-4.1-Final-Fixer.zip​
Click to expand...
Click to collapse
ASDK 4.2.2 Reborn v2.0
Features for 4.2.2 kernel version
Only for AOSP Roms running 4.2.2
Linux kernel 3.0.74
GPU clock to 320MHz fixed
Governors (FANTASY, SAVAGEDZEN, MINMAX, SLP, ABYSSPLUG, INTELLIDEMAND, ASSWAX, BADASS, SUPERBAD, LAGFREE, SLEEPY, SCARY, WHEATLEY, LAZY, ADAPTIVE, INTERACTIVEX, SMARTASSV2, INTERACTIVE, PEGASUSQ, LIONHEART, CONSERVATIVE, POWERSAVE, ONDEMAND, USERSPACE, PERFORMANCE)
Schedulers (CFQ, BFQ, VR, SIO, NOOP, DEADLINE, ROW, ZEN)
Overclocking & Undervolting
Temperature Throttle
Fast Charge
Hotplug
Max OC 1.836ghz (PLEASE DON'T OC TO 1.836 AND EXPECT IT TO BE STABLE THEN COME TO THE THREAD AND COMPLAIN)
Compiled with Linaro 4.7.3 toolchain
I need testers, if it did not boot for me I would not upload it.
These are beta.
DOWNLOADS
ASDK-testing-HERC4.2-04-23-2013.zip
DO NOT RELINK MY KERNELS ON OTHER SITES, NO MIRRORS..
I would suggest people BACKUP and reflash CLEAN, setup (CLEAN ROM), and then Flash my kernel. Leave it at default settings a few hours to settle, and then tweak if you like.
If you Brick your device, kill your sd, or lose data, It's on you. And you probabally shouldn't be on XDA downloading and flashing ROM's and KERNEL's.​
Click to expand...
Click to collapse
Credit/Thanks
BIGGEST THANKS TO DAGR8 FOR HIS KKO KERNEL AS IT WAS THE BASE FOR ASDK KERNEL FOR SGS2
Ayysir
Ktoonsez
Imoseyon
Thomas.raines
Krazeecracker
Android88
Ptmr3
Cl3Kener
elbermu
And many, many more.
TESTERS
PJcastaldo
Mycars12
gigoo25
​
Click to expand...
Click to collapse
IF YOUR GOING TO USE THINGS FROM THIS SOURCE, PLEASE ASK FIRST!!!
Source: https://github.com/thdDude/ASDK-GS2​

Reborn - [KERNEL][JB-4.1/4.2][3/25/13] All-Star Devs Kernel: Reborn v1.4
4-12-13
- OC to 1.8 ghz
- Re did Undervolt in code
- Fixed min/max at boot
- ASDK Gov tweaked a bit

Im first!!! LOL . Ive never been first before!

Re: [KERNEL][JB-4.1][1/22/13] All-Star Devs Kernel
Sweet thanks! I'll try this out later but so far the stock PACman kernel has been doing wonders. Hopefully this is the same!

Re: [KERNEL][JB-4.1][1/22/13] All-Star Devs Kernel
Second!
Sent from my SAMSUNG-SGH-T989 using xda app-developers app

Re: [KERNEL][JB-4.1][1/22/13] All-Star Devs Kernel
Reserved
Edit: nvm lmao

Everybody: Enjoy the kernel! You'll love it! This is ayysir's second kernel as a part of the team. He has been working extremely hard on this. Let us know how it is!

Re: [KERNEL][JB-4.1][1/22/13] All-Star Devs Kernel
Am here..
So far so good...all seem well.. Great job guys:thumbup:
ROW scheduler missing
Sent from my SAMSUNG-SGH-T989 using Tapatalk 2

Re: [KERNEL][JB-4.1][1/22/13] All-Star Devs Kernel
Exelent....my friend....:beer::thumbup:
Enviado desde mi SAMSUNG-SGH-T989 usando Tapatalk 2

does this kernel support Capacitive Buttons Backlight changing?

Re: [KERNEL][JB-4.1][1/22/13] All-Star Devs Kernel
The kernel, flashed on all star Rom v7 is working better than I thought, got an extra hour of battery life than lightning kernel. (5 hour with screen on whole time before)
~°~°~°~°~°~°~°~°~°~°~°~°~°~°~°~
Phone: Samsung Galaxy s2 T989 Hercules
Rom: Jedi Jelly 4
Kernel: Insecure Kernel
Radio: LB7 Blaze
~°~°~°~°~°~°~°~°~°~°~°~°~°~°~°~
I am going to try and make an app, if anyone wants help this beautiful talented celebrity in making it just message me!

Re: [KERNEL][JB-4.1][1/22/13] All-Star Devs Kernel
This kernel sends awesome! But rotation is off on slimstar 1.21. I wiped system and caches, installed rom and gapps, rebooted, then went back into recovery to flash kernel. Looking forward for a fix. This doesn't happen with nibbles.
Sent from my SAMSUNG-SGH-T989 using xda app-developers app

Re: [KERNEL][JB-4.1][1/22/13] All-Star Devs Kernel
niccuany said:
This kernel sends awesome! But rotation is off on slimstar 1.21. I wiped system and caches, installed rom and gapps, rebooted, then went back into recovery to flash kernel. Looking forward for a fix. This doesn't happen with nibbles.
Sent from my SAMSUNG-SGH-T989 using xda app-developers app
Click to expand...
Click to collapse
For now just flash the rotation fix.
Sent from my Nexus 4 using xda premium
---------- Post added at 10:03 AM ---------- Previous post was at 10:02 AM ----------
kamilmirza said:
does this kernel support Capacitive Buttons Backlight changing?
Click to expand...
Click to collapse
What do you mean "changing"?
Sent from my Nexus 4 using xda premium

Re: [KERNEL][JB-4.1][1/22/13] All-Star Devs Kernel
First of all ayysir I love you!
And second of all flashing right now =)
Sent from my SGH-T989 using xda premium

android88 said:
For now just flash the rotation fix.
Sent from my Nexus 4 using xda premium
---------- Post added at 10:03 AM ---------- Previous post was at 10:02 AM ----------
What do you mean "changing"?
Sent from my Nexus 4 using xda premium
Click to expand...
Click to collapse
can i change the brightness level of capacitive buttons in this kernel?

i dont know if im missing it or what, but abyssplug is not there.
had the rotation problem but it was nothing that fixer couldn't handle.
also, camera lag is still lingering. however, its definitely not as bad as it was. its a lot more bearable. 4 out of 5 pics taken are lagfree.
GOOD WORK, TEAM!

Re: [KERNEL][JB-4.1][1/22/13] All-Star Devs Kernel
kamilmirza said:
can i change the brightness level of capacitive buttons in this kernel?
Click to expand...
Click to collapse
Pretty sure that feature doesn't exist at all for our device.
Sent from my SAMSUNG-SGH-T989 using Tapatalk 2

Re: [KERNEL][JB-4.1][1/22/13] All-Star Devs Kernel
Getting sod on SLP gov.
Sent from my SAMSUNG-SGH-T989 using xda premium

corwest said:
Pretty sure that feature doesn't exist at all for our device.
Sent from my SAMSUNG-SGH-T989 using Tapatalk 2
Click to expand...
Click to collapse
really?

Re: [KERNEL][JB-4.1][1/22/13] All-Star Devs Kernel
android88 said:
For now just flash the rotation fix.
Sent from my Nexus 4 using xda premium
---------- Post added at 10:03 AM ---------- Previous post was at 10:02 AM ----------
What do you mean "changing"?
Sent from my Nexus 4 using xda premium
Click to expand...
Click to collapse
Specifically , flash the rotation fix FIXER not just the rotation fix , took me a while to figure this out , loving the kernel!
Sent from my SAMSUNG-SGH-T989 using Tapatalk 2

[Kernel][3.4.20][MpDecision][OC]Forzaferrarileo JB kernel V4

So , let's start again with jb kernel .
It's only for stock JB(4.1.2) based rom, don't use it for AOSP BASED ROM (CM9,CM10,CM10.1,AOKP,EOS, etc... ) I'm not responsible for any damage caused by my kernel , use it as your risk
Features
[V1] Prerooted and with cwm recovery (thanks to Doomlord)
[V1] CPU OC up to 1900 Mhz and UC to 30 Mhz
[V1] Build Optimization
[V1] Compiled with Linaro
[V1] VDD sysfs (voltage control interface)
[V1.1] Boot freq capped at 1512Mhz
[V1.1] Upstream to Linux 3.4.3
[V1.1] Two version : 1.7 Ghz and 1.9 Ghz
[V1.4] WriteBack tweaks
[V1.4] Gpu 2D/3D OC
[V1.4] Tweaked a bit Lionheart
[V1.4] Use glibc for memcpy and memmove
[V1.4] Increased Sd card cache(READAHEAD)
[V1.4] LINUX 3.4.4(from 3.4.0)
[V2] Added and tweaked MpDecision to have best performance and battery life
[V2] LOAD_FREQ (4*Hz+61) avoids loadavg moire
[V2] Some scheduler Tweak
[V2] Pipe compiling
[V2] Arm Thumbee support
[V2] Emmc latency decreased (more reactive)
[V2] Tweaked slub allocator
[V2] Tweaked Lionheart Governor to be less aggressive , so more battery friendly
[V2] Tweaked Pegasusq Governor to be more interactive and with better hotplug decision
[V2] Linux 3.4.20
[V2] Reworked a bit GPU OC
[V3] Improved WorkQueue for high priority
[V3] Switched build optimization
[V3] Tweaked Badass governor
[V3] msm :kgsl : Process all idle checks
[V3] Cpu1 fix : Cpu1 will follow cpu0 governor and min/max freq
[V3] Added Simple GPU governor (thanks to @faux123 ) ->>>>>>>>> To enable it use Trickster Mod app or Fauxclock app
[V3] Base for thermal management
[V3] Switched to westwood TCP congestion algorithm
[V4] Updated Fm radio drivers from CAF
[V4] Added Fastcharge , thanks to @DooMLoRD http://forum.xda-developers.com/showthread.php?t=2305591
[V4] Added optimized AES and SHA1 algorithms
[V4] Enabled thermal managment
[V4] Enabled Mpdecision inputboost
[V4] Enabled NTFS
[V4]Enabled UTF8 (unicode character)
Governor
[V1] Enabled Interactive governor
[V1.4] Lionheart governor
[V2] Added Pegasusq governor -> [Removed in V3 ]
[V3] Added Badass governor ( thanks to @show-p1984 )
[V4] Added Dancedance governor
Scheduler
[V1] Added SIO scheduler
[V1.4] Added Zen scheduler
[V2] Added Row scheduler
[V3] Added Fifo scheduler
[V3] Added Row scheduler
[V3] Added Fiops scheduler
Credits
Doomlord for his ramdisk and for helping me http://forum.xda-developers.com/showthread.php?t=2305591
Sony for the source
Dpiroto for the bootlogo (it's the same of the ICS v3.1)
Showp1984 for mpdecision and help
Faux123
Download link
V4 1.7 GHz version :https://app.box.com/s/9oadz509u6jw7epsp0p5
V4 1.9 GHz version :https://app.box.com/s/408x8ft0ar48qbesocc7
Older version
1.9 Ghz version V1.4 : https://www.box.com/s/65palxlrf2csznvccyb9
V3 1.7 Ghz version : https://www.box.com/s/vnfd8qo08554i4jq82zh[/URL]
V2: 1.7 Ghz version : https://www.box.com/s/zq1utioo2ucjcug68bqy
V2: 1.9 GHz version : https://www.box.com/s/6p0v26wode816plmvwa5
1.7 Ghz version V1.4 : https://www.box.com/s/2ss323q9v71m5dak5b2m
My sources are visible on github : https://github.com/Forzaferrarileo/fuji-msm8660-JB-3.4.0
The thread is going to be improved
The bootlogo is going to be changed

FAQ
WIFI PROBLEM
If you want leave my kernel , remember to flash stock wifi modules in recovery . You can download it from here : https://www.box.com/s/jcl0as39lz1zxdlcwrcc
[PAY ATTENTION , ITS ONLY FOR V2 ]If your wifi doesn't turn on try to reflash the kernel , or flash this : https://www.box.com/s/fhjo0zfciti5gfab7dt7
if the problem persist , reflash it in recovery and next fix permission

Does the kernel boot with those frequencies or the stock ones?

WOOOW..... XS has so many great developer ...... thank you ... will try this ... :good: :good: :good:

revan17 said:
Does the kernel boot with those frequencies or the stock ones?
Click to expand...
Click to collapse
Yes the kernel boots at 1900. This evening 1.7 ghz version and also 1.5 ghz. V2 will have boot freq capped at 1512 mhz
Sent from my LT26i using xda app-developers app

thanks for your good work
can i use this for SL too?

Jamal_RS said:
thanks for your good work
can i use this for SL too?
Click to expand...
Click to collapse
Yes
Sent from my LT26i using xda app-developers app

Forzaferrarileo said:
Yes
Sent from my LT26i using xda app-developers app
Click to expand...
Click to collapse
hi ..i use xs
on first run i've got 10117 score on antutu v3.3 ( antutu set on 1900 mhx x 2, even though i set on 1.782 mhz ) ...., using no frills cpu and set to 384 - 1.782 , interactive and sio ....
on other run ( 5 time ) , no mather seting on no frills cpu i use, the score never get pass 6000 .... did i miss something ?

Try setting both cores with performance governor, which keep the cpu at max freq.
The frequencies above 1728 mhz(1782 , 1836 and 1900) have an overclocked bus (360 mhz instead of the stock 310) , so you'll get more boost using these frequencies.
Sent from my LT26i using xda app-developers app

. elf file please.
edit: sorry, elf file included. thanks.
Sent from my LT26i using xda premium

jaxzkeren said:
hi ..i use xs
on first run i've got 10117 score on antutu v3.3 ( antutu set on 1900 mhx x 2, even though i set on 1.782 mhz ) ...., using no frills cpu and set to 384 - 1.782 , interactive and sio ....
on other run ( 5 time ) , no mather seting on no frills cpu i use, the score never get pass 6000 .... did i miss something ?
Click to expand...
Click to collapse
During test put phone into fridge (freezer is the best), coz it reaches 80*C and decreases freq to 800MHz. In freezer it doesn't heat itself so much But I got 10260 points and I don't think that more is reachable without any other tweaks than OC...

How is the performance? Anyone tried play games with this kernel?
I'm on Trinity's kernel right now and it works great ,performance is very good and games work super fast. Please ,any feedback?

davidbar93 said:
How is the performance? Anyone tried play games with this kernel?
I'm on Trinity's kernel right now and it works great ,performance is very good and games work super fast. Please ,any feedback?
Click to expand...
Click to collapse
For now only Antutu, but 2d/3d is similar, so should be similar
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

kubekpop said:
For now only Antutu, but 2d/3d is similar, so should be similar
Click to expand...
Click to collapse
There's no gpu oc, this will come later
Sent from my LT26i using xda app-developers app

What's the difference between this and doomkernel? Except overclocking coz I don't use it
Sent from my LT26i using xda app-developers app

Forzaferrarileo said:
There's no gpu oc, this will come later
Sent from my LT26i using xda app-developers app
Click to expand...
Click to collapse
All right, but does it give sth? On ICS it didn't give any points for me, dk how about games...

zaidx said:
What's the difference between this and doomkernel? Except overclocking coz I don't use it
Sent from my LT26i using xda app-developers app
Click to expand...
Click to collapse
Governor
[V1] Enabled Interactive governor
Scheduler
[V1] Added SIO

Also the compiler and the build optimization(they made a very little speed up)
Sent from my LT26i using xda app-developers app

Forzaferrarileo said:
Also the compiler and the build optimization(they made a very little speed up)
Sent from my LT26i using xda app-developers app
Click to expand...
Click to collapse
Thanks Linaro 4.7 Works xD

1.9Ghz?
Nice, but XS won't last long with that kind of OC...
Excellent work, many, many tnx but are you sure it's wise to OC to 1.9?
Sent from my LT26i using Tapatalk 2

|KERNEL| SaberN3Kernel_10.7 || 3.4.75 || OC for all || exFAT | 12/23

{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
SaberN3Kernel ​This Kernel Is Compatible with all TW/Samsung based JB ROMS for this device--- (Not AOSP)​
READ, READ, READ before downloading, flashing, or posting questions
Not all phones are created equal meaning some phones will not handle Overclocking / Underclocking or Undervolting as well as others.
So far this is tested and working on:
(SD 800 Processor N3 Only!!)
SM-N900T
SM-N9005
SM-N900W8​
Features
OC to 2.649GHz
UC to 266MHz
Kernel Version 3.4.75
UV Support to 700
Advanced Power Emulation
Default Scheduler= Row
Default Governor= Ondemand
Default boot set to 2..3Ghz (2.2656)
Built using arm 4.7 toolchain
Touchwake
CPU Boost Driver
Init.d
Ramdisk Mods
- Temporary patch solution for wifi, forcing change in build.prop (Jovy23)
- SELinux= Permissive
- Insecure (Remount not yet online)
Exfat Supported
Added Schedulers:
-FIOPS
-ZEN
-SIO
Edits to DEADLINE for better performance
Added Gov:
-Wheatley
USB FastCharge (USB Charges at AC level)
Faux's Overall Stats for quad core devices (This will show overall CPU frequency statistics via sysfs.)
Faux's CPU Freq Limiter (This driver limits MSM CPU frequency through sysfs file system)
More...
Github
In my GITHUB you can find my sources and code changes
Credits
Samsung for Official Source Code
Xiaolu
Faux123
DoomLord
danieljamie
dormanx
Jovy23
markbencze
livlogik
Imoseyon
Yank555!
Instructions
TWRP Recovery HIGHLY Recommended!
-Download Kernel
-Flash Kernel
-Boot system and DO NOT TOUCH FOR 2-3 MIN
Changelog
Code:
12|23--10.7
There have been many Jedi Elite exclusive versions of Saber so this is a catch up Changelog
-Upgraded to to 3.4.75!
-Touch Wake Implementation Thanks to Yank555!! (will drain battery faster)
-CPU boost driver thanks to Yank555 and Saravana Kannan
-Voltage Modifications
-Removed ifdefs. Unified kernel now
-Edits to Defconfigs
-Dropped bottom freq to 266mhz
-Voltage mods for STABILITY ;)
-Thermal edits
-Edits to Defconfigs
10|25-- 5.2
Patched All the way up to 3.4.67!! (Imoseyon responsible for patches from 3.4.6-3.4.66)
Cores should now all behave as instructed
ALOOTT of voltage work, we can now ALL Run with a RED Saber!!!
Thermal edits
Edits to Defconfigs
Ramdisk edits to improve USB connection Recognition
10|16-- 3.0
3 different kernel choices
-Green = No OC + All Features
-Yellow = OC to 2.5 + All Features
-Red= OC to 2.7 + All Features
Added Schedulers:
-FIOPS
-ZEN
-SIO
Edits to DEADLINE for better performance
Added Gov:
-Wheatley
USB FastCharge (USB Charges at AC level)
Faux's Overall Stats for quad core devices (This will show overall CPU frequency statistics via sysfs.)
Faux's CPU Freq Limiter (This driver limits MSM CPU frequency through sysfs file system)
10|15-- 2.3
-Dropped UV limit
-Work with cpu
10|15-- Initial Release (See Features List)
Downloads
READ BEFORE DOWNLOADING
SaberN3Kernel_Red-10.7
http://d-h.st/znG
Support this Development By clicking this Button,,, Thank you
http://forum.xda-developers.com/donatetome.php?u=4488450
Guide to Thread Participation":
Generally speaking, we are a pretty calm group of people, but as with so many other things in life, there are those that evoke a negative response from the very start. THAT is why we are such believers in maintaining a polite, respectful thread. Most everyone here is eager to help, and the only thing we ask is (despite the associated tedium) read the entire thread, it can only help. If and when you are still stuck, feel free to ask questions, we're all here to help one another.
--TMobTim
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------​
XDA:DevDB Information
|KERNEL| SaberN3Kernel_10.7 || 3.4.75 || OC for all || exFAT | 12|23, a Kernel for the T-Mobile Samsung Galaxy Note 3
Contributors
ptmr3
Kernel Special Features:
Version Information
Status: Stable
Created 2013-10-15
Last Updated 2013-12-23

mine

Great work as always bro. Killing it already!
Sent from my SM-N900W8 using Tapatalk now Free

Very nice work done, looking forward to using this when I get my note 3.
Sent from my note 2 ya bish!

You are the man, again!
Sent from my SM-N900T using Tapatalk now Free

Downloading now!!! Thank you for your hard work and support of the Note 3 :thumbup:
Sent from my SM-N900T using XDA Premium 4 mobile app

Thanks for for the Beast, banging on it right now:good:

Woot!
Sent from my SM-N900T using Tapatalk

Nice downloading now. Thanks once again ptmr3
Sent from my SM-N900T using Tapatalk

Installed fine with darthstaker rom wifi seems to be working great as well. Thanks for the kernel. Looking forward to a rom son too hopefully .
Edit: it seems that using an app like trickster mod to put the max cpu at say 1.3ghz only caps cpu 1. Cpu2,3,4 still go to 2.5ghz. Anyone else have this problem?
Sent from my SM-N900T using Tapatalk

For uv do we need trickster mod, or should setcpu work?
Sent from my SM-N900T using Tapatalk

Nice to see you around ptmr3. Been looking forward to seeing you post in here.
Sent from my SM-N900T using XDA Premium 4 mobile app

Admiral2145 said:
For uv do we need trickster mod, or should setcpu work?
Sent from my SM-N900T using Tapatalk
Click to expand...
Click to collapse
Trickster will flash right in along with the kernel. One of the best apps for kernel control available IMO

Admiral2145 said:
For uv do we need trickster mod, or should setcpu work?
Sent from my SM-N900T using Tapatalk
Click to expand...
Click to collapse
I usually try to stick with what the Dev uses, in this case I'm fairly certain it's Trickster, but to each his own.. Let us know either way you go what kind of results you're getting.. :thumbup:
Sent from my SM-N900T using XDA Premium 4 mobile app

This one will not go lower than 800 on voltages. Have a more aggressive kernel testing now
Sent from my SM-N900T using xda app-developers app

ptmr3 said:
This one will not go lower than 800 on voltages. Have a more aggressive kernel testing now
Sent from my SM-N900T using xda app-developers app
Click to expand...
Click to collapse
so i assume we need to wipe cache and dalvik correct? thats what i always did for kernels.

So much smoother, the responsiveness is better, not just blowing smoke. My floating toucher app is actually working flawlessly now, it would be unresponsive to my first touch half the time, now no issues .. I'm pretty happy already and I haven't done any tweaking.. So happy you're working on this device
Sent from my SM-N900T using XDA Premium 4 mobile app

XxLostSoulxX said:
so i assume we need to wipe cache and dalvik correct? thats what i always did for kernels.
Click to expand...
Click to collapse
Not necessary but you can if you want
Sent from my SM-N900T using xda app-developers app

ptmr3 said:
This one will not go lower than 800 on voltages. Have a more aggressive kernel testing now
Sent from my SM-N900T using xda app-developers app
Click to expand...
Click to collapse
When i load up tickster it shows everything from 576mhz and lower at 775. This is the default that loads for me? is it going to that or is it only really at 800.

Prod1702 said:
When i load up tickster it shows everything from 576mhz and lower at 775. This is the default that loads for me? is it going to that or is it only really at 800.
Click to expand...
Click to collapse
It is that low, but if you go to change them, they will default to 800. I will have a fresh one up in maybe an hour
Sent from my SM-N900T using xda app-developers app