Develop Bugs

[Q] Odin fail, bricked?

I attempted to return my phone to stock via Odin, I used the T-Mobile ROM and I have a Telus phone, stupid I know. The Odin attempt failed.
I then tried with the Telus version and Odin just gave me a quick run through, didn't flash, I hit the reset button, tried again, same thing.
I closed Odin in desperation, restarted it and tried to flash the Telus version, it is now stuck here:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T989DTLKJ3_T989DTLKJ3_T989DTLKJ3_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
I followed the guide, I do have the correct ROM, the phone is still in recovery and I know if I attempt a restart it will likely hard brick, can I save this???

Just re-run it until it completes. keep trying, sometimes it takes a few tries to go through

xcrazydx said:
Just re-run it until it completes. keep trying, sometimes it takes a few tries to go through
Click to expand...
Click to collapse
+ 1
Sent from my SGH-T989 using xda premium

I ended up unplugging the phone, shutting down Odin and reinstalling Samsung drivers. Plugged the phone back in and it installed, phone is all good now.

trying to odin back to stock odin has frozen

odin seems to have frozen no blue line on the phone
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> SPH-D700-FC09-8Gb-REL.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
I really dont want a brick here any ideas?

zsnethen said:
odin seems to have frozen no blue line on the phone
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> SPH-D700-FC09-8Gb-REL.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
I really dont want a brick here any ideas?
Click to expand...
Click to collapse
What cable are you using? Usually this means its stuck and its not going to continue you wont brick it totally pulling it out but you will soft brick it which is fixable by what your doing now. I would suggest pulling it off, go get a good thick cable, and hope that the phone goes into download mode still.

unplugged and got back into download mode odin back to stock. on a different note i'm doing all this to activate my phone on sprint agian is there an easier way?

zsnethen said:
unplugged and got back into download mode odin back to stock. on a different note i'm doing all this to activate my phone on sprint agian is there an easier way?
Click to expand...
Click to collapse
Take it to a sprint store? Probably would be the best bet, but not now that you have soft bricked it. Probably should have asked that before trying to go back to full stock. You could have just flashed a stock gingerbread ROM if you were rooted.

Just get a better cable.
Sent from my SPH-D700 using xda premium

U will be fine. Just pull the battery, put it back in, and boot back into download mode. Just make sure u have a good data cable like blackberry...etc..
Sent from my SPH-D700 using xda premium

Fyi, if u get a diamond and android guy on the screen when booting. Keep battery off for about 5 mins
Sent from my SPH-D700 using xda premium

My Samsung Note 2 is...BRICKED? Don't start (Galaxy Note 2 Brikkato, Non Parte !)

Hiii!!!
My Name is Adonis and i'm Italian Boy ^_^ Best fan for The GREAT JOB of This Site! i Vey Vey Love XDA! *_*
Mhhhh...but I try to ask your help..... :good: Pleasssseeeeee
I have the Some Problem with My NEW Samsung Galaxy Note 2....................
I recently installed a Root Permissions on Original Firmware, and I then installed a Custom Rom (I am Italian so I chose an Italian ROM COOKED ^ _ ^) of cis80. Up to yesterday's .. All okay!
For a Stroke, unfortunately, the phone started to reboot without any reason, and the last time it was restarted .. in a like Boot Loop... O_O The Phone Locked on screen "Samsung Galaxy Note 2 N7100" Without going on Next Logo of Loading (As Default What Samsung).
I've tried EVERYTHING .. but really .. I say to ALL! But nothing to do ..... What is the only one that I can to enter into "Download Mode" .. with Odin I've tried everything but everything I always returns "FAIL" or "Error Pit" & more .... or another Error. Also NAND Erase, nothing nothing... :_(
AIUTOOOOO!! I do not know Do! I have the Note 2 to 10 days c.a. ... and now I can't use it ..... My Beast is Down...

First, this isnt be .. a phone for kids.
Second, if you can enter into Download Mode, could be fixed. (If you couldnt enter you should need jig usb)
3rd, if you dont know what the hell are you doing, leave stock ROM.
Cya

Kashamalaga said:
First, this isnt be .. a phone for kids.
Second, if you can enter into Download Mode, could be fixed. (If you couldnt enter you should need jig usb)
3rd, if you dont know what the hell are you doing, leave stock ROM.
Cya
Click to expand...
Click to collapse
Ok Thanks.
But i Try....and i don't have any solution.
i tried load a Stock ROM with ODIN....but i have a Error....Because i have a "Error with a Table Partition"... "Error with Pit File"....i try load a Pit file, but not load anything.... can i do?

This is un example of report of ODIN:
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MODEM_N7100XXALIH.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7100OXXALJ1_BTU_CSC_factory.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Removed!!
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003>
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
<OSM> All threads completed. (succeed 0 / failed 0)
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_N7100_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Removed!!
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
Click to expand...
Click to collapse
and ODIN with last line come in standby... if i insert a PIT File for remapping of partition..if i not insert this, say there is an error with partition..... (
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003>
<ID:0/003> There is no PIT partition.
Click to expand...
Click to collapse

Adonis4U said:
This is un example of report of ODIN:
and ODIN with last line come in standby... if i insert a PIT File for remapping of partition..if i not insert this, say there is an error with partition..... (
Click to expand...
Click to collapse
What version of odin r u using? Try to get 1.85 version, redownload software for ur note2(try diferent version), run as administrator and try again.
Sent from my GT-N7100 using xda premium

szymi22 said:
What version of odin r u using? Try to get 1.85 version, redownload software for ur note2(try diferent version), run as administrator and try again.
Sent from my GT-N7100 using xda premium
Click to expand...
Click to collapse
I used the Version 3.04 e 3.07. But the Version 1.85 Not. Ok i Try!
I Tried used various Version of Stcok Firmware...All Italian...but nothingfor All...

Adonis4U said:
I used the Version 3.04 e 3.07. But the Version 1.85 Not. Ok i Try!
I Tried used various Version of Stcok Firmware...All Italian...but nothingfor All...
Click to expand...
Click to collapse
Try 1.85 odin and if that wont help try to download non italian rom, uk one works for me before when i fixed my friend note 2
Sent from my GT-N7100 using xda premium

You try
1. download Stock ROM file
2. Use Odin 3.07 (recommend)
3. Open Odin (on computer use normal harddisk. Not solid stat drive,SSD) check Auto Reboot and F. rest Time and Nand Erase All OR Repartition (If you have PIT file)
4. Check PDA and select Stock ROM (your downloaded)
5. Start
6. Finished Flash Rom. You Remove USB and restart Your phone will stop at samsung logo. Never mine. You restart again (Hold power button). Enter stock recovery mode (Vol Up + Home + power button).Your Phone show error can't read data.
7. In stock recovery menu. You check wipe cache. and wipe cache+factory reset. and restart your phone.
8. Your phone may come back normal.
good luck.

[Q] Bricked GT-N7100, is the my problem hardware or software?

Good day, guys! Sorry if my first post is related to a problem. I'm pretty new to Android so please bear with me...
So I woke up this morning and my Note 2 won't completely boot, it goes as far as "Samsung Galaxy Note II GT-N7100" screen and just completely gets stuck. I tried to charge it but it just shows the empty battery icon. I left it charging overnight so I don't exactly know what happened. My phone is completely stock, rooted it before then un-rooted later. No custom ROM, no custom recovery etc.
I tried to boot to Recovery Mode but it won't let me. Luckily it can boot to Download Mode. I figured I would flash it to stock ROM since I was still at 4.1.1 maybe I would just update to 4.1.2. I downloaded the firmware from sammobile.com and used Odin but it fails every time with this message:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_N7100XXDLJ2_422394_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/015> Odin v.3 engine (ID:15)..
<ID:0/015> File analysis..
<ID:0/015> SetupConnection..
<ID:0/015> Initialzation..
<ID:0/015> Get PIT for mapping..
<ID:0/015>
<ID:0/015> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/015> Removed!!
Can someone point out the problem to me? I've read around that this is probably SDS but I'm still hoping that it's not. I bought my phone from another country so taking it back would be a little difficult.
Any help appreciated. Thank you!

Need Help. Bricked phone after trying to rollback to 4.4.4

So I was trying to rollback to 4.4.4 from the latest Att update 5.0.1 that we got a week ago. Now my phone is stuck in Download mode and does not reboot. I even tried the Keis method with no luck. Still keeps going back to this screen with this error.

I kno this might not be much help, but with the latest AT&T update 5.0.1 COC5, I think you can't rollback to 4.4.4
I kno 100% Verizon latest 5.0.1 you can't rollback either...
But for all these reasons is why I'm still on 4.4.4 NK3 update had this update since day one I bought this phone
But hope the best luck to you... you might have to install 5.0.1 again
Sent from my SAMSUNG-SM-N910A using Tapatalk

Yes I hope someone can please help.
Sent from my SAMSUNG-SGH-I337 using Tapatalk

If I need to return phone to fix? Who should I deal with AT&T or Samsung. I was going to blame it on the latest software update.
Sent from my iPod touch using Tapatalk

borijess said:
If I need to return phone to fix? Who should I deal with AT&T or Samsung. I was going to blame it on the latest software update.
Sent from my iPod touch using Tapatalk
Click to expand...
Click to collapse
Flash the new firmware back onto your phone. ..

I could not flash anything. It just kept failing. I even tried kies method with no success.
So I called AT&T and blamed it on there latest update. Took it to an AT&T warranty store and they gave me a new note 4. They tried to flash with there software and had no success either.
So I walked out with new note 4. So beware people do not try to rollback if you accepted att latest update. You will brick device. [emoji20]

hi guys,
looks like i just did the same thing. I was trying to downgrade my wife's AT&T note 4 since she's been having tons of issues with this phone (this is actually her second note 4). anyways, long story short, i am now stuck at the same screen you are at. i've tried odin 3.09 and downloaded the COC4 files (4 files, BL, AP, CP, and CSC). and when i run odin i get an error message, and it fails to install.
here's the message i get:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BL_N910AUCU1COC4_CL4160876_QB4512549_REV00_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> AP_N910AUCU1COC4_CL4160876_QB4512549_REV00_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CP_N910AUCU1COC4_CL4160876_QB4512549_REV00_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_ATT_N910AATT1COC4_CL4160876_QB4512549_REV00_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl1.mbn
<ID:0/003> rpm.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
can anyone help me out here? should i start my own thread?
thanks in advance

Try just flashing system and nothing else

thanitos said:
Try just flashing system and nothing else
Click to expand...
Click to collapse
sorry for the dumb question, but which file is that?

Won't work. I had to return phone to att. They gave me a new one. I told them the latest update killed my phone.
Sent from my SAMSUNG-SM-N910A using xda premium

itsjustlenny said:
sorry for the dumb question, but which file is that?
Click to expand...
Click to collapse
Try with out BL file.

senseless returns like these two are what makes modders look bad in their eye; on the other hand if the bootloader was unlocked and they didn't lock it down so tight they wouldn't have these issues as well

Making up a lie and committing Fraud is not something I recommend doing.
It sucks but if you mess around with your device and ruin it/can't fix it then take responsibility for what you did.

davidstech11 said:
Making up a lie and committing Fraud is not something I recommend doing.
It sucks but if you mess around with your device and ruin it/can't fix it then take responsibility for what you did.
Click to expand...
Click to collapse
Get off your high horse. If att didn't lock this phone up so tight we wouldn't have these issues. If you don't want to do it don't go around judging others.
Sent from my SAMSUNG-SM-N910A using xda premium

borijess said:
Get off your high horse. If att didn't lock this phone up so tight we wouldn't have these issues. If you don't want to do it don't go around judging others.
Sent from my SAMSUNG-SM-N910A using xda premium
Click to expand...
Click to collapse
If you did your homework, you would have known not to downgrade. It's irresponsible people like yourself that have caused these phones to be locked down. It's also the reason we are now paying so much for them. And finally, davidstech11 was accurate with his comment. Course it's not human nature to do the right thing which is what makes those that do stand out from the rest.

are there a solution i have the same problem n910a

firebird7880 said:
are there a solution i have the same problem n910a
Click to expand...
Click to collapse
Read this whole thread. http://forum.xda-developers.com/showthread.php?t=3335880
Sent from my SM-N910T using Tapatalk
---------- Post added at 09:06 PM ---------- Previous post was at 09:03 PM ----------
itsjustlenny said:
hi guys,
looks like i just did the same thing. I was trying to downgrade my wife's AT&T note 4 since she's been having tons of issues with this phone (this is actually her second note 4). anyways, long story short, i am now stuck at the same screen you are at. i've tried odin 3.09 and downloaded the COC4 files (4 files, BL, AP, CP, and CSC). and when i run odin i get an error message, and it fails to install.
here's the message i get:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BL_N910AUCU1COC4_CL4160876_QB4512549_REV00_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> AP_N910AUCU1COC4_CL4160876_QB4512549_REV00_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CP_N910AUCU1COC4_CL4160876_QB4512549_REV00_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_ATT_N910AATT1COC4_CL4160876_QB4512549_REV00_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl1.mbn
<ID:0/003> rpm.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
can anyone help me out here? should i start my own thread?
thanks in advance
Click to expand...
Click to collapse
You're using the wrong files. You must use the same OS files that your phone is on or newer OS files. It's showing that the authorization is not letting it write to the system because it's not the right files.
Sent from my SM-N910T using Tapatalk