Hey guys,
I've searched the forum for like 5 hours or so
to find a thread that could help me solve this solution...
I've tried everything that had something to do with "dead"
in the BlueAngel and Blueangel Update etc. section
What it does:
- The screen stays black
- If I try to charge, the Red 'Charging' LED doesn't become red
unless I take the battery out of the Qtek and charge..
Then it gets red (WEIRD)
- No connection with activesync or rom update utilities
What happened:
- Rom update stopped after a few percentages...
If i try to get a new rom in it with or without cradle
with the following rom update utilities:
- BaUpgradeUt.exe:
then I get a Connection Error (101) when I try to update
- MaUpgradeUt_noID.exe:
ERROR 150: ROM UPGRADE UTILITY ERROR
(Rom Utility not designed for this device)
or "Finished" immediately (but it's not finished)
(Depends on the rom I use, and I used like 10 different roms)
Soft reset / Hard reset doesn't work,
I even tried to Hard Reset by holding the
Voice Record button + Power button + Reset button for 2 minutes
(I tried Camera + Power + Reset too) with the battery,
and I tried these without the battery...
No reaction...
If someone can help me, please do...
Thnx in advance
Maybe you can try thingds from this
http://forum.xda-developers.com/viewtopic.php?p=291989#291989
sep said:
Maybe you can try thingds from this
http://forum.xda-developers.com/viewtopic.php?p=291989#291989
Click to expand...
Click to collapse
Nope,
I've tried that too, but I don't get the USB or WCEUSB in mtty...
The COM ports don't react.
I know how to use it, because I used it like 10 times or somethin'
But I think the problem is, that I can't get in the bootloader mode
(or any other mode)... So there's no response from my Angel..
Thanks anyway..
have you tryed to remove battery, leave it without battery fo an hour or two then put the battery back and power on the device ?
this method may boot your device. If it worked go imediately in bot loader mode and reflash your favorite rom
If it does not helps maybe it is hardware problem ... and you should leave your device in service center
Tried this too
Isn't there any solution except for service center?
I want to know how I can solve this problem,
'cause it could happen again when I update the rom later.
And I know I'm not the only one with this problem.
It would help me and a lot of other BlueAngel owners..
Is it possible to make a serial connection with the bottom I/O port and issue the necessary commands with mtty? could be that there is some logic powered on the board but not enough to make the "USB" section powered up.. similar to serial a console cable on network gear etc. OR.. is there any known secrets such as a hardware debug mode initiated with certain pin(s) on the I/O connector.. such as grounding one or two.. any HTC tech documents floating around for troubleshooting?
You are not one with this problem. The same happens with me too.
Let searching for solution together.
If you want you can contact with me by icq: 190812766
Hi,
I have a Samsung Galaxy S Plus here which is almost brand new and has only been used for some phone/texts/emails so far.
I connected it to a PC running Samsung Kies and it told me there was a firmware update available for this phone, so i clicked ok and had it install.
During the installation, at 22%, everything freezes and locks up, it remained at 22% for 45 minutes until (after some googling) i was recommended to just turn it off / reboot it.
After rebooting, i constantly get this icon on the screen :
Copy & paste the following in a web browser (as I'm not allowed to place a link or picture apparently)... : img267.imageshack.us/img267/930/fotofg.jpg
I tried removing the battery for 10 seconds and then boot it up again - same screen.
And it doesn't matter if its connected to the PC or not, its always that screen.
And when it IS connected to the pc, samsung Kies shows the 'connecting' screen but it never actually connects.
What do I do ?
How is it possible that someone's phone gets locked/frozen for simply trying to update ?!
orangewall said:
Hi,
I have a Samsung Galaxy S Plus here which is almost brand new and has only been used for some phone/texts/emails so far.
I connected it to a PC running Samsung Kies and it told me there was a firmware update available for this phone, so i clicked ok and had it install.
During the installation, at 22%, everything freezes and locks up, it remained at 22% for 45 minutes until (after some googling) i was recommended to just turn it off / reboot it.
After rebooting, i constantly get this icon on the screen :
Copy & paste the following in a web browser (as I'm not allowed to place a link or picture apparently)... : img267.imageshack.us/img267/930/fotofg.jpg
I tried removing the battery for 10 seconds and then boot it up again - same screen.
And it doesn't matter if its connected to the PC or not, its always that screen.
And when it IS connected to the pc, samsung Kies shows the 'connecting' screen but it never actually connects.
What do I do ?
How is it possible that someone's phone gets locked/frozen for simply trying to update ?!
Click to expand...
Click to collapse
have the same problem ... did u solving ?
XXX.hard-reset.com/samsung-i9000-galaxy-s-hard-reset.html
Copy and paste into address bar not allowed to post links. Substitute xxx for www
Custom solution
Hello,
It's a big problem, but maybe can you blame samsung? However, I don't know if you have CMW, but try to boot that and than install custom rom (a zip rom). After that you can install original firmware.
If that doesn't work find a rom that works with odin, boot in download mode and install that rom, after that install original firmware.
Similar thing append to me but wile using odin i got the same screen.
What i did was connect it gain to the pc, odin detected it and was able to flash the rom.
It was pretty scary i assure you.
My advise is if the phone is brand new take it to your dealer a let them sort this out as it was not your fault at all.
If it's a brand new phone I'd use Samsung's warranty or maybe even return it.
Hi all!
i wrote reviews for two devices that are very interesting on checking together.
iPega 9023 rev2 -> Telescopic bluetooth controller for smartphones/phablets/tablets and standalone usage.
Teclast X89
There is a summary of the Teclast X89 Device. (sorry, but i can´t post complete article here, due the limitations of the characters by message on this forum)
_______________________________________________________________________________
[REVIEW] Teclast X89 Baytrail Tablet Dual OS (Windows & Android)
Acknowledgments
To Geekbuyingstore for send me a sample of their product Teclast X89 to test it and write this review.
Note about this review
This article is the first part of the main review of the device. Currently i get bricked the device when trying to update/install a clean windows version, and i can´t keep testing for now, until i found the way to recover it
When i get the device unbricked (if i get this), i will post a second part with steps for recovery, firmware update, tips and tricks for this device.
This article is based on general usage of the device, and for windows get many videos of games running directly on the device itself, for showing what you can expect of this.
For technical info and benchmarking on windows, when i get this device operative again, i will update this article with these sections.
Apologize if the article is not enough informative as you can expect. I'll do my best to bring a second part with more info about this device.
Product showcase(Checking of the external view of the package)
First of all, i never mention about packaging of the store that sent to me their articles, because usually i don´t consider interesting to mention, but this time i will do an exception because i get so pleased about this point.
For this review, Geekbuying sent to me two devices (but i wrote in different articles) that correspond to a suggested (by me) combo for use together:
Tablet Teclast X89
iPega 9023 controller
Both of them come in the same package, but fully protected, first with the typical plastic with bubbles, covering all the content:
Then, there is a bag with protective system for avoiding shocking of the devices.
The package arrives without any kind of problems, with the original packaging of the devices in perfect condition.
I wanted to remark this because is not usual that stores give this attention on the devices they send.
Now, back to the device itself. the packaging of it is simple, but all main texts are in chinese.
In the front we found the name of the product (Teclast tPad), and the Intel logo, that give to us a main clue about what is inside.
Back part is the description of the product in chinese
Note that there is no info about the specific model of the tablet (Teclast X89)
Inside we found the basic distribution of the package
Product information
According with the manufacturer, or searching info on web pages, we can found many sources of information about the device and sometimes these information may be not consistent (may be different from one web page to other), and this may cause some confusion for anybody that wants to get info about this product.
On this section i will post the info i get from the manufacturer (or is not possible, the web page that i consider more reliable), listing only the relevant points for a tech analysis of the product, and omit these points that don´t get any relevant info about the device (as many time we found on many pages, things such video capabilities, mail capabilities, etc, that really are software based features that we can install on the device, and not a real feature of the device itself)
I did not found the official specs on Teclast webpage. There is the specs of the previous version (X89HD), but not for this specific device (Teclast X89, or Teclast X89 Retina Display)
Operating System: Android 4.4 & Windows 8.1 OS (Dual Boot)
Model: Teclast X89 Dual OS
Announced: 2014-07
Color: White
Shell Material: Plastic
Display
Size: 7.9 Inch
Resolution: 2048*1536
Display Technology: IPS Retina capacitive touch screen
CPU&GPU
CPU Manufacturer: Intel
CPU Model: Bay Trail-T Z3735F
CPU Core: Quad Core
CPU Speed: 1.83GHz
RAM&ROM
RAM Type: DDR3L
RAM: 2GB
Hard Drive Type: eMMC
Hard Drive Capacity: 32GB
Extend Card: T-FLASH(Support 32G MAX)
Other Functions
Camera
Front: 2.0MP
Back: 5.0MP (Autofocus)
HDMI: Up to 1080p
3G: Supporting external 3G modem
Bluetooth: 4.0
GPS: NO
G-Sensor: Four way
Power
Battery Type: Li-ion battery, 5000mAh
Battery / Run Time(up to)
Wifi On: 4 hours
Wifi Off: 8 hours
Power Device Type: AC Adapter, AC 100-240V
Charging Voltage: DC 5V, 2A
Communications
Wireless ConnectionWIFI
Wireless Protocol802.11 b/g/n
Dimensions200 ×138 ×7.4mm
Net Weight512g
Connectors Ports
1 x Micro USB Port
1 x Earphone jack
1 x Micro HDMI port
1 x Micro SD Card slot
Hope you found interesting and useful.
_______________________________________________________________________________
Zalu2!
Not booting to windows after root
Hi,
I was reading your review about teclast x89, it is awesome.
I was following your instruction for rooting my dual boot teclast x89 (E7ED), and everything went great, i was rooted.
But then my problem apear, i can't boot into windows. Menu for selecting which OS to boot, dissapear. I try every single combination of key, but everytime it boots to Android. CAN YOU PLEASE HEEEEELP ME?
Thanks
djshorty said:
Hi,
I was reading your review about teclast x89, it is awesome.
I was following your instruction for rooting my dual boot teclast x89 (E7ED), and everything went great, i was rooted.
But then my problem apear, i can't boot into windows. Menu for selecting which OS to boot, dissapear. I try every single combination of key, but everytime it boots to Android. CAN YOU PLEASE HEEEEELP ME?
Thanks
Click to expand...
Click to collapse
Hi.
The rooting method will not affect to booting selectiong of OS.
of select, power on the device, and after release the power button, press VOL- & VOL+ at the same time.
the device will ask you to select an Operating System.
another way is connect any USB keyboard (via USB OTG cable), and when turning on the device hit quickly and repeat the "supr" key, for entering to BIOS.
once you get on BIOS interface, go to second screen and select "OS Selection" (or something this way, sorry i can´t check now) as first booting method.
This will enable the OS selection screen
check my review (on my blog) and follow the instructions for configuring the bios for select OS, and add more time for pressing Supr (by default is 1 or 2 seconds, i don´t remember. i suggest 4 or 6 seconds)
Greetings!
Deen0X said:
Hi.
The rooting method will not affect to booting selectiong of OS.
of select, power on the device, and after release the power button, press VOL- & VOL+ at the same time.
the device will ask you to select an Operating System.
another way is connect any USB keyboard (via USB OTG cable), and when turning on the device hit quickly and repeat the "supr" key, for entering to BIOS.
once you get on BIOS interface, go to second screen and select "OS Selection" (or something this way, sorry i can´t check now) as first booting method.
This will enable the OS selection screen
check my review (on my blog) and follow the instructions for configuring the bios for select OS, and add more time for pressing Supr (by default is 1 or 2 seconds, i don´t remember. i suggest 4 or 6 seconds)
Greetings!
Click to expand...
Click to collapse
thanks for the reply,
i try both of your method but no luck,
First, i select power on the device, and after release the power button, press VOL- & VOL+ at the same time. It goes in "dmx" fastboot mode,
Second,
When i enter in bios (supr-del key), in boot manu i have 3 options:
1. UEFI OS (it boots directly to android)
2. Windows boot manager (it boots directly to win)
3. UEFI: built in EFI shell( it opens shell)
can you please check in your tablet what option you have at boot manu?, are they same with mine, what did you select?
What ever i try, i can only boot to android or windows, i cant get screen where i can choose what os to start. Before it was screen this screen
with Operating System selection, but now is gone..
please help!!
p.s in windows now, touch is not working, android is ok.
Thanks
djshorty said:
thanks for the reply,
i try both of your method but no luck,
First, i select power on the device, and after release the power button, press VOL- & VOL+ at the same time. It goes in "dmx" fastboot mode,
Second,
When i enter in bios (supr-del key), in boot manu i have 3 options:
1. UEFI OS (it boots directly to android)
2. Windows boot manager (it boots directly to win)
3. UEFI: built in EFI shell( it opens shell)
can you please check in your tablet what option you have at boot manu?, are they same with mine, what did you select?
What ever i try, i can only boot to android or windows, i cant get screen where i can choose what os to start. Before it was screen this screen
with Operating System selection, but now is gone..
please help!!
p.s in windows now, touch is not working, android is ok.
Thanks
Click to expand...
Click to collapse
If you has been removed this View attachment 3193425
TRY IT →bbs.teclast.com/forum.php?mod=viewthread&tid=389148
mooncake5874 said:
If you has been removed this View attachment 3193425
TRY IT →bbs.teclast.com/forum.php?mod=viewthread&tid=389148
Click to expand...
Click to collapse
Yes, i removed that Stupid of me
Thanks, i will try this, but i dont know chinese, i try to download and tell you results.Is this apk?or all firmware?
Thanks
djshorty said:
Yes, i removed that Stupid of me
Thanks, i will try this, but i dont know chinese, i try to download and tell you results.Is this apk?or all firmware?
Thanks
Click to expand...
Click to collapse
I made the same mistake:crying:,but I can't find download for this apk at that time. so I reinstall all firmware.
this APK backup. file path“/system/app/”
↓
View attachment VManager.apk
GOOD LUCK!
mooncake5874 said:
I made the same mistake:crying:,but I can't find download for this apk at that time. so I reinstall all firmware.
this APK backup. file path“/system/app/”
↓
View attachment 3193597
GOOD LUCK!
Click to expand...
Click to collapse
Thanks,
i install it but no luck.
Should i open this program and select something, or is it enough thaat i installed it?
ANd it will be very good if someone who knows to make a tutorial in english to flash new firmware from scratch (instaling dual boot, android, windows) like x98, that is good tutorial.
Thanks
djshorty said:
Thanks,
i install it but no luck.
Should i open this program and select something, or is it enough thaat i installed it?
ANd it will be very good if someone who knows to make a tutorial in english to flash new firmware from scratch (instaling dual boot, android, windows) like x98, that is good tutorial.
Thanks
Click to expand...
Click to collapse
Maybe you can use google translation
mooncake5874 said:
Maybe you can use google translation
Click to expand...
Click to collapse
I use google translate, but it is awful, i downlod tutorial pdf file, and translated, but i am afraid that i can make mistake because translation is awful.
If someone who knows chinese and english can translate it right it will be good.
Or someone can confirm that tutorial for x98 3g is the same as this only the files are different, that is also good think to do.
currently, i'm writting a second part of the review, with instructions for flashing the device, installing android and windows (both)
for now, i'm a little bit busy and i can´t give so much time, but let me some days and i will publish this part of the review, for helping flashing the device.
Deen0X said:
currently, i'm writting a second part of the review, with instructions for flashing the device, installing android and windows (both)
for now, i'm a little bit busy and i can´t give so much time, but let me some days and i will publish this part of the review, for helping flashing the device.
Click to expand...
Click to collapse
Thanks for everything i manage to repair my tablet by installing dual boot.
If you need help about your review, i can help just tell me. And as suggestions to your review, you can write what apps are safe to remove, so people cant get into trouble like me. Also you can write how can we install only android or only windows, for big storage 32gb to be used only for 1 system
Thanks everybody.
Hibernat does not work
Hello X89 owners,
i also have the newest dual boot retina display version and i am really impressed by the tablet. All works fine and great performance. Only one thing does not work that worked fine for all my other windows tablets i use before. I am not a big fan of connected standby because it still drains battery, so i use "%windir%\System32\rundll32.exe powrprof.dll,SetSuspendState" command to hibernate the devices (because default button is not visible).
Unfortunately it does not work with the teclast x89. If i run "%windir%\System32\rundll32.exe powrprof.dll,SetSuspendState" hibernate command it shuts down the tablet but after reboot it does not restore the hibernate state, it simply boots up normally. I also checked event log having error:
error: Windows failed to resume from hibernate with error status 0xC000000D.
I also tried recreating hiberfil.sys and checking disc consistence. But nothing helped. So can you try this on your devices? I simply want to know if its a general Teclast X89 problem...
Thx and br
Arangato
Hi Arangato.
I'm doing some testings with MeegoPad T01 (similar baytrail than Teclast), and as you i can´t get this thing to hibernate by command line
messing with the device, in some moment i get an effective hibernate state, but i'm not sure how i get.
in some testings, after unplug the power and connect again, the device boot windows (quick than normal) from scratch, and show me the application i get running previous the sleep (burnout paradise)
i will keep doing tests, but i really don´t know how to replicate for now. This messages really is for confirme that there is some way to do a sleep on this device, but of course, is not the standard way.
i'm thinking now... may be when i sleep the device, i think i keep the power button pressed to shutdown... for long time, after this unplug power source, wait few seconds and plug again. (something like this i did, i think)
keep testing...
"powercfg -h on" should enable hibernate mode
But the difference between a cold boot and hibernate resume is not that long
aitnog said:
"powercfg -h on" should enable hibernate mode
But the difference between a cold boot and hibernate resume is not that long
Click to expand...
Click to collapse
i tried but did not enabled.
yeah, may be on timing is the same, but there is a good difference. With Hibernating, when you get back, get all the tasks you're doing in the same status (games, work, etc). i really prefer hibernate than complete turn off for this reason.
but thanks anyway.
i recovered the tablet and doing some testings (but for now i´m centered on other devices i must release reviews).
meanwhile, i published the guide for flashing and recover the device, translating the original in chinese, and adding some other stuff that may be useful.
http://manguiro.blogspot.com/2015/03/guide-teclast-x89-installation-guide.html
Note: if your device cannot recover (like mine) with normal steps, or there is some message about corrupt partition table, invalid disk, etc, you must do some manual steps (the flashing tool can´t handle this)
i will put my steps on other article (really, i need to publish another reviews first), but basically i opened the flashing xml file, and check that there are some commented lines that, if you uncomment, the flashing tool will omit anyway, then you must do these steps manually, from fastboot command.
with this, i be able to 100% recover the device. Now i get android and windows working without problems.
hope you found useful.
Touch has stopped working! In windows.
djshorty said:
Thanks for everything i manage to repair my tablet by installing dual boot.
If you need help about your review, i can help just tell me. And as suggestions to your review, you can write what apps are safe to remove, so people cant get into trouble like me. Also you can write how can we install only android or only windows, for big storage 32gb to be used only for 1 system
Thanks everybody.
Click to expand...
Click to collapse
Hey my touch stopped working in windows too.
Anyone have any idea how to fix it? I have only had this for 1 hour and now it is useless for what I got it for...
I need to find out how to restore the touch capabilities to windows. I tried refreshing, it happened after I went to android for the first time.
I've got the Atom Z3736 Win 8.1 version of this but does anyone know if it's possible to install dual boot because this version uses the Z3735?
Because just about all the forums for this device are in Chinese and using Google translate is a nightmare to even find the right people to ask.
com.android.systemui keeps crashing when charging level at 100%
Hello,
recently I get my Teclast X89 tablet, but unfortunately it appeares to have a problem. When the battery charging level comes to 100% (at 99% everything is OK) tablet becomes totally unusable. When the screen is switched off it cannot be waken up and when I use the tablet a window pops up telling that "Process com.android.systemui has stopped", like here:
imgur.com/hjWI1lP
After restart everything is OK, but it really grinds my gears. Maybe someone know how to fix this problem?
Please halp!
Bogusz
Hello Deen0X, thanks for your reply and explanation. Now i know it seems to be a general problem. If you have a tablet like this connected standby is activated and with this hibernate is also enabled by default (you should find a hiberfil.sys file in C root, its used for fast boot option) so you normally can hibernate with the command i mentioned before: "%windir%\System32\rundll32.exe powrprof.dll,SetSuspendState" this works fine for my other acer win 8.1 tablet (OOTB system) directly after install. But not for the Teclast x89. Of course having a normal boot and restore from hibernate is pretty same time, also fast boot does not have that big impact. I like hibernate because it "freezes" actual system status without draining battery after that.. i often have several browser windows opened, some other metro apps and i like to resume to that state and not to have a clean boot.
@Deen0X: could you check your event log? Is there also the message that device could not restore from hibernation?
So keep me updated, or maybe anybody else can try the "%windir%\System32\rundll32.exe powrprof.dll,SetSuspendState" command to hibernate the teclast x89 dual boot. It will not harm the device. I have the experience if hibernation is disabled and you run this command it simply locks the screen..
Thx and br
Arangato