Develop Bugs

Qtek 9090 Dead - Update not 100%, no reaction, no bootloader

Hey guys,
I've searched the forum for like 5 hours or so
to find a thread that could help me solve this solution...
I've tried everything that had something to do with "dead"
in the BlueAngel and Blueangel Update etc. section
What it does:
- The screen stays black
- If I try to charge, the Red 'Charging' LED doesn't become red
unless I take the battery out of the Qtek and charge..
Then it gets red (WEIRD)
- No connection with activesync or rom update utilities
What happened:
- Rom update stopped after a few percentages...
If i try to get a new rom in it with or without cradle
with the following rom update utilities:
- BaUpgradeUt.exe:
then I get a Connection Error (101) when I try to update
- MaUpgradeUt_noID.exe:
ERROR 150: ROM UPGRADE UTILITY ERROR
(Rom Utility not designed for this device)
or "Finished" immediately (but it's not finished)
(Depends on the rom I use, and I used like 10 different roms)
Soft reset / Hard reset doesn't work,
I even tried to Hard Reset by holding the
Voice Record button + Power button + Reset button for 2 minutes
(I tried Camera + Power + Reset too) with the battery,
and I tried these without the battery...
No reaction...
If someone can help me, please do...
Thnx in advance

Maybe you can try thingds from this
http://forum.xda-developers.com/viewtopic.php?p=291989#291989

sep said:
Maybe you can try thingds from this
http://forum.xda-developers.com/viewtopic.php?p=291989#291989
Click to expand...
Click to collapse
Nope,
I've tried that too, but I don't get the USB or WCEUSB in mtty...
The COM ports don't react.
I know how to use it, because I used it like 10 times or somethin'
But I think the problem is, that I can't get in the bootloader mode
(or any other mode)... So there's no response from my Angel..
Thanks anyway..

have you tryed to remove battery, leave it without battery fo an hour or two then put the battery back and power on the device ?
this method may boot your device. If it worked go imediately in bot loader mode and reflash your favorite rom
If it does not helps maybe it is hardware problem ... and you should leave your device in service center

Tried this too
Isn't there any solution except for service center?
I want to know how I can solve this problem,
'cause it could happen again when I update the rom later.
And I know I'm not the only one with this problem.
It would help me and a lot of other BlueAngel owners..

Is it possible to make a serial connection with the bottom I/O port and issue the necessary commands with mtty? could be that there is some logic powered on the board but not enough to make the "USB" section powered up.. similar to serial a console cable on network gear etc. OR.. is there any known secrets such as a hardware debug mode initiated with certain pin(s) on the I/O connector.. such as grounding one or two.. any HTC tech documents floating around for troubleshooting?

You are not one with this problem. The same happens with me too.
Let searching for solution together.
If you want you can contact with me by icq: 190812766

O2 XDA Exec Dead after interrupted Rom Upgrade :-(

Hi,
I was upgrading my XDA Exec using Xda_Exec_Upgrade_v1.30.162.exe
My laptop died. It sometimes overheats but it hadn't happened in a while.
I now can't progress past the bootloader even after full clean reset.
Anyway. I have the O2 screen reading:
R 1.04.01
G 42.37.P8
D 1.13.82 WWE
My laptop detects a USB connection, although it says "USB Device Not Recognised". Activesync 4.1 won't detect it, however, I've tried changing settings etc but to no avail.
I've trawled the board here and found people recovering from similar situations with other devices. Am I gonna be able to restore my beloved exec from paperweight-status?
btw: am in Ireland where O2 don't support the exec and bought it from a guy in the UK who got it as an unwanted upgrade. have flashed it before just fine...but don't think I'll be able to return it to O2 as UK and IRL are not the same company...
Help?
Mark
p.s. ran BL10_RUU_UNI_V11.exe and got 101 connection error :-(
EDIT:
Fixed, using bootloader mode and re-running the upgrade. thanks

xda neo crash
You need to reinstall your windows mobile 5 system. If you are using orginal german neo rom, you can download rom from o2 web site, or you can download from this sites ftp server

thanks for the feedback,
I found the info on restarting in bootloader mode (i had previously misunderstood "bootloader") and was able to re-flash it by USB no probs.
I now have a happy XDA

Hello there ...I have about the same problem with my MDA Vario....could you explain how do I "restart in bootloader mode"?
My PPC just stucks before loading windows...
thanks

How to get bootloader mode
Ok, did a bit of a lookaround and got this (I thinkg the MDA Vario is the XDA Mini)
For Xda II and Xda IIi
- Press & hold the power button
- Press & hold the D pad (5 way directional button)
- Push the stylus into the soft reset hole - until you see the word 'Serial' on the screen.
You should now be able to follow the upgrade process above for a device stuck in Bootloader mode.
For Xda IIs
- Press & hold the power button
- Press & hold the Camera button
- Push the stylus into the soft reset hole - until you see the word 'Serial' on the screen.
You should now be able to follow the upgrade process above for a device stuck in Bootloader mode.
For Xda Exec
- Press & hold the power button
- Press & hold the Backlight button
- Push the stylus into the soft reset hole - until you see the word 'Serial' on the screen.
You should now be able to follow the upgrade process above for a device stuck in Bootloader mode.
For Xda Mini S
- Press & hold the voice command button
- Push the stylus into the soft reset hole (short quick press). Keep hold of the voice command button until you see the screen with multicolored horizontal stripes). The device is now in Bootloader mode and you can follow the upgrade process above for a device stuck in Bootloader mode.
EDIT:
The rest of the process (just in case you need to know) is as follows:
(and if you have problems open your connection settings in activesync and ensure that USB is unchecked...that is OFF. remember to reset the USB settings once you've successfully upgraded)
in 'Bootloader' mode
When this happens the device screen will be blank except for the words;
Serial
v 1.00a
The word 'Serial' should change to 'USB' when the cradle is plugged into the PC, and the version number below this will vary. When you get this screen, a soft or hard reset will not make any difference.
It is still possible to run the ROM upgrade file again, WITHOUT using Activesync (activesync will not restart anyway).
Firstly unplug the USB cradle and reboot the PC
Plug the cradle back into the USB port (this must plug directly into the USB port and not into a USB Hub/adaptor).
Now run the ROM upgrade file again from the PC. This should just run as per normal and correctly reflash the device.

Thanks bob_jesus!!
I am already in bootloader mode....Could you tell me where I can find the files to flash it? My device is Tmobile MDA Vario. Are there different files for flashing for every device? (O2 XDA mini s, MDA Vario, imate kjam...)??
Thanks again

Hi Ermoscow,
I'm sure if you trawl around the boards a bit you'll find it. I'm pretty new to this but yes, all these devices tend to have a different Rom, and each device itself tends to have a different Rom based on your mobile carrier.
e.g. I use an XDA exec which is the same as an HTC universal, they could theoretically use the same Rom but not the same rom as an XDA mini.
Again, this is all in my understanding and keeping it simple.
another idea would be to check the t-mobile site and download your rom directly from them, it should be available. if i find anything for you i'll post back.

Thank you everybody!
After managing to get to the bootloader mode I made a rom update which solved the problem!
Now it works great again!
thanks

Botloader Mode
I have a bricked MDA as I had a power outage while flashing the ROM. Can someone tell me how to recover. I find references to folks entering bootloader mode and then recovering, but I cannot find a post that tells me how to do it. Can anyone help? [email protected]
I'm desperate!
Regards,
Bob

Hi, which MDA is it because the instructions should be included in my post up above. You just need to find which XDA your device corresponds to and go from there. All that info's in this forum somewhere for sure.
Best of luck!

XDA Exec Dead after interrupted Rom Upgrade
XDA Exec Dead after interrupted Rom Upgrade
Hi
I was installing new ROM WM6.1 on autom exec when it rebooted it was showing black screen and just vibrating. as when I hard rebooted it after removing my phone battery and again press the power button it was again showing the black screen and vibrator continues it is not bootng up.
can any one help me please.
How can I reinstall the the old rom using usb
help required....
Please help....

It´s always good to READ the Wiki:
http://wiki.xda-developers.com/index.php?pagename=Uni_ROM_Upgrade
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader_Serial

Keys dont work
Hey i just put WM6.1 on my xda exec and it works fine apart from the keys not working so i have to type using the touch screen and the WI-FI randomly turns off and on i was wondering if anyone else had these problems and if they could help.
Thanks

Urgent Help Required Please>

Is This the correct section ?
I have a xda2 exec. I tried to update my rom, the congratulations screen displayed with a checking informaton on device message, this froze for some time so I disconnected the usb cable. when I tried to reset it, I get is a dispaly with just colours on it and it does nothing else, when I try to update again it shows an error connection error 101, also the device is not recognised. Is there a way to resolve this issue please and can someone be kind enought to direct me.
I used the rom update from - my-xda.com/xdaexec_soft2.html
Thank you in advance.

Try to hard reset your device
hold buttons: "-" + "-"
and then reset
so in practical terms, push the top 2 dash keys which are between your green and red phone icon buttons, and while holding them reset your device using the pen.
this should give you a white screen with a little menu.
You can now select clear device or something, I think it's the 0 or the X
it should work
if that doesn't work try to put your device in Bootloader
buttons: Backlight (front little button) + power button + reset button (with your pen)
again, hold the backlight and power button, then reset button
the screen should be dark, but if you look real close it would say USB or Serial v1.0 or v1.1 or something
you should be able to flash now using the tool
Also look around on this forum, loads of topics about upgrading/flashing and hanging problems
more info: http://forum.xda-developers.com/showthread.php?t=290234

u might have to update bootloader, try 2 read wiki.xda-developers.com lots of usefulll infos for beginers

Thank you
To both members above, thank you for your time. I am now using the update tool, hopefully this will now work. I used the method pressing the light button and power and reset. (Bootloader)

Dead SPV M5000 / Universal

Hi All
I posted this in another forum... but hope its better suited here.
My Father has an SPV M5000 (HTC Universal). He has unlocked the SIM lock from IMEI number some time ago.
Recently it started going screwy and so he did a soft reset and then it wont turn on at all.
He has let me play with it and if I try a hard reset it comes up with the screen saying "press 0 to restore...", but if you press 0 it says "clearing now" and then appears to switch off. If you press x it also appears to switch off.
You can enter bootloader mode and it displays SERIAL on the screen - when you plug it in to a PC the screen changes to USB. But when I try connecting using MTTY I get no USB port - although selecting COM5 seems to open a command prompt window - but to be honest I dont know where to go from here.
If I try a soft reset it seems to do nothing - although the orange charging light blinks once.
With it connected to a PC in bootloader mode I was able to reflash the ROM and it went through all three stages correctly and indicated it had been successful - but when you finish with a hard reset it appears to turn off.
Before I use it to wedge my living room door open, can anyone offer any advice? I have perused the forum, but cannot find anything which seems to match the fault I am getting.
I know its not the battery as I have the same model and the battery is new.
I suppose if nothing can be done... does anyone have any ideas what to do with it now?
Thanks in advance
SlipMat

Perhaps you can find something on the Wiki:
http://wiki.xda-developers.com/index.php?pagename=HTC_Universal
Hope it helps,

Phone won't start up ?

Here's the thing , I unlocked my bootloader and rooted my phone a while back (probably using an already outdated software , if i remembered correctly it was 2.3.3 , but i knew i followed the instructions here
http://forum.xda-developers.com/showthread.php?t=1133650)
Today, my phone asked if I wanted to update the software (like an automated software update) and i could choose to update or not and i chose yes but now , my phone won't start up for like 3 hours already . I tried turning it on but it won't turn on , i tried charging it but there isn't any lights which was supposed to be there .
So I decided to google it and i followed the instructions here
http://talk.sonyericsson.com/thread/26720
but after installing both , choosing my phone , followin the instructions on update service , it gets stuck on "it contains a modified software that cannot be updated" so decided to come back here to ask you guys what I should do .
Right now , all I want to do is for my phone to start up again , any ideas ?
edit : right now , i took out the battery , and put it back in . This time when I tried to turn it on , the vibrate is there which wasn't there initially and theres 1 flash of the green light on the side of the phone .
and also , i think its recognized by the computer because i can hear the sound notification (the same sound when you plug a USB into a computer) which wasn't there before I did the update service thingy .
edit 2 : it won't go into safemode either when i tried clicked the right and left buttons below the display (the menu and back button) and the power button after that . yes i tried reinserting the battery .
edit 3 : I'm not sure if this'll help but my phone is recognized as SEMC flash device (i checked on device manager) and theres a green colour non flashing light when i plug my phone into the pc .

http://forum.xda-developers.com/showthread.php?t=1304634

OMG
Thanks
Sorry for not searching , I tried looking for Xperia arc won't load up / start up but it didn't give me this thread .
Thanks again
edit : i thanked you too

same problem!!!
Guys, I was trying to modify my phone so that applications would be saved in memory card instead of internal storage, so I rooted it and stuff.. Now it won't turn on!!! When I switch it on, it shows the SE logo and does nothing else.. I tried to enter the safemode menu (holding left and right keys when switching on, or volume down key and home key when turning on) but nothing works!!! I'm like desperate now so any help would be really appreciated!

gadjet87 said:
Guys, I was trying to modify my phone so that applications would be saved in memory card instead of internal storage, so I rooted it and stuff.. Now it won't turn on!!! When I switch it on, it shows the SE logo and does nothing else.. I tried to enter the safemode menu (holding left and right keys when switching on, or volume down key and home key when turning on) but nothing works!!! I'm like desperate now so any help would be really appreciated!
Click to expand...
Click to collapse
Try to flash a new(er) kernel with recovery and install a new rom (your phone is ota-bricked, so if that doesn't work, search on XDA)
Sent from my LT18i using xda premium