On previous android file systems I was able to manually assign the phone a static ip, dns, gateway, subnet, however I can't seem to figure out how to do it on ICS. Can this no longer be done or has it been moved somewhere in settings I'm overlooking? I'm having trouble connecting to my home network, however I know if I set up everything manually using static values I'll be set. I go to Settings -> Wifi -> : -> Advanced -> but nothing there to change the phone static information.
-EDIT-
Nevermind got it, but have another question below. Under wifi, hold the network and then choose modify. Put in IP address you want phone to be, gateway for router, Internet DNS information, and the subnet 24 for 255.255.255.0. I did it wrong the 1st time and assuming it was asking for router info and IP and not to assing the phone a specific IP address too
Long press on your networks SSID in the list of available networks and select 'modify network'. From here you can set everything manually.
Long press on the access point you want to change the settings for and choose "modify network". From the pop up window tick "show advanced options".
Sent from my Galaxy Nexus using Tapatalk
Thanks guys I figured it out. When I originally did that I thought it was for router info, so I stuck the IP address of the router in IP slot and not gateway at the time. Went back in and it just dawned on me. Back to setting up the new toy.
Don't want to waste space with a new thread, but must the router be broadcasting? I've always been able to setup without broadcasting the router, however I turned off wifi and turned it on and ICS cannot find the router and connect unless I'm broadcasting. I prefer to not broadcast my router for the neighborhood to see, despite having security encryption on
Related
Hi,
I'm experiencing a weird problem and please let me know if it's only my problem or there is some work around for it.
My phone is SX66 upgraded to 1.40 ROM + 1.13 Radio stack
I can connect Wifi fine whenever I have some phone signal (at work). Whenever I go home where the phone signal is weak then the WIFI couldn't get connected (I believe I set up my home network correctly as I've been using it for so long and configure it for several computer/laptop in house). The network could detect the AP with the SSID but I just couldn't connect to it even I'm sitting right next to the AP.
ROM 1.40
Radio: 1.13
MDD
Are you sure it isn't connecting? What has led you to this conclusion?
Is it possible that it is connecting, but that you just can't browse the internet, in which case check your connection proxy settings. If your work uses a proxy server and you've enabled the pass-through setting in ActiveSync, your network connection may be configured with your work proxy server.
If you're sure you're just not connecting however, things to check are;
WEP/WPA Encryption - If you're using it and have other wireless devices on your network, you no doubt know what to do. If not, say so & I can help you.
DHCP - Does your router/AP support Auto-IP Addressing? Is it enabled? If not, you'll have to configure the WiFi card with a static IP within the same subnet as your router. Ask if you need help.
MAC Filtering - Are you blocking unauthorised MAC Addresses (on your router/ap)?
Interference - Wireless A/V Senders and digital cordless phones are common culprits for RFI. 802.11x APs support multiple channels (most default to channel 11), and you can change these in case of interference. Once again, if you have other WiFi gear already connected with good, strong signals, you can probably discount this one.
Sorry if this is all elementary to you - I don't know how technical you are.
Thanks for your reply.
> Are you sure it isn't connecting? What has led you to this conclusion?
Yes, I've check wireless status on the phone. "Connected to the network", and the AP with DHCP on showed the status of an IP has been allocate to the SX66 mac address. However I dont' really believe it then I check the "Adater", it said network available, and the WIFI icon just didnot show any traffic.
> Is it possible that it is connecting, but that you just can't browse the internet, in which case check your connection proxy settings. If your work uses a proxy server and you've enabled the pass-through setting in ActiveSync, your network connection may be configured with your work proxy server.
I've experience once with the internet connection via Active Sync so I disable the passthrough. Both home and work doesn't have proxy server so I selected not to have any on the phone.
> WEP/WPA Encryption - If you're using it and have other wireless devices on your network, you no doubt know what to do. If not, say so & I can help you.
At work, I have 128 WEP and the connection works fine with the key. At home, I open my network but using MAC filtering to protect it. I have problem with the open network one at home. Perhaps, I will try to setup WEP at home and see if it can work.
The only thing I'm not really clear is the difference between setting "WPA" and "WPA-PSK" from the phone.
> DHCP - Does your router/AP support Auto-IP Addressing? Is it enabled? If not, you'll have to configure the WiFi card with a static IP within the same subnet as your router. Ask if you need help.
Yes, DHCP enable as I don't want to change it back and forth when traveling.
> MAC Filtering - Are you blocking unauthorised MAC Addresses (on your router/ap)?
I do it and I already opened the network and then captured the MAC address into the AP memory. (that's why I think it's connected but will check).
> Interference -
Not really, I'm 6' away from the AP and I don't have any cordless device in my computer room.
> Sorry if this is all elementary to you - I don't know how technical you
are.
No problem, I'd like to learn more about this PDA. The concept is about the same with PC, but the tools to debug is not there. I can't use tracert/traceroute, ifconfig or ping broadcast to really know if I'm the network.
Once again, thanks a lot.
Okay, well it sounds like you're on the right track & know what you're doing.
A useful troubleshooting tool, which gives you tracert, ping, whios, ipconfig and a host of other tools is "vxUtil", which is freeware. I'd give you a URL for downloading it, but I'm on my iMate now (sipping coffee by the Yarra in a Melbourne Cafe - oh what a techno-wanker am I!), but search these forums or Google it and you'll find it.
Now, regarding the proxy thing... These PPCs are a little tricky with their internet settings, and I had to create a different 'connect using...' connection profile, if that makes sense. The important setting within the profile, which is under the Proxy tab, from memory, is "This network connects to the internet".
Now for some reason, if you don't enter in a proxy server here, that check-box doesn't stay checked when you ok your way out. So what I've had to do is go into the advanced area & enter anything in the "wap" proxy, then ok out.
Strange, but it seems to work. Although I always leave my "Private network" on "My Work Network", I can now browse the 'Net through the WiFi AP/Router.
Download vxUtil & see if you can ping your AP, then go from there.
I've worked around the problem by using static IP address instead of depending on DHCP. Thanks to Hitchhiker software. I noticed that it was trying to obtain IP address from DHCP but failed. (The very same DHCP work wells for the rest of my network). Anyway, I will use Hitchhiker to switch IP back and forth if necessary.
Thanks a lot!
MDD
Great to hear you found the problem - well done.
I have a t-mobile Dash. I'm trying to connect to my home router/AP using WPA2-PSK. I've double-checked my network key and other settings, but I can't seem to get it to connect. Here are my settings:
Network name: GTHOME <- matches my router's broadcast SSID
Network type: Internet
Not a hidden network
Not an ad-hoc connection
Authentication: WPA2-PSK
Data encryption: AES
The key is not automatically provided
Network key: (matches my router's key)
Key index: 1
Does not user IEEE 802.1x network access control. (I've tried it both ways, with PEAP
On trying to connect, my Dash give this message:
"Cannot connect to the network. Check your network and service provider settings and try again."
The AP is a Netgear WPN824 v2 with the latest firmware. Any suggestions?
TIA
Try using a 9 letter word for your key.
I had an 8 letter key before. I tried 9 - no luck. What's magic about 9?
Mac Address Filter
skyguy said:
I had an 8 letter key before. I tried 9 - no luck. What's magic about 9?
Click to expand...
Click to collapse
Guy, do you have a Mac Adddress Filter area on your router?Open your router so no key is required to make a connection and after you establish a connection use the WEP or WPA2-PSK key option! Can you find your Mac address and your Phone's Ip address on your router. You can find this info on your phone also in Comm Manager> setting> Wifi> Connection Status area. There is a place on your router to put this info, so that the router will know that its ok to connect to this device with this info, I believe its in the advance area on your router and use the 10 key WEP if possible!
Install NetWorkMagic To You System
Go to http://www.networkmagic.com and install the trail version on your PC. Networkmagic will tell you if your system is setup correctly or if their is some kind of problem. Use the network map, this will give you a good ideal of whats going down on your system......! If you cannot see your phone on the network map, then Houston, we got a problem...........!But we will fix it! Happy Thanksgiving!
skyguy said:
I had an 8 letter key before. I tried 9 - no luck. What's magic about 9?
Click to expand...
Click to collapse
Yep 8 is secure enough. try again without any caps or numbers. e.g. give aaaaaaaa a try
And see that error you mention, that looks like the one IE gives. What happens when you press connect in the wifi list?
I found that having any character other than a-z, 0-9 would cause the dash to fail to connect even though pc's and laptops had no problems. My initial key contained a "-" and "$"-- it drove me crazy trying to figure out the problem until I realized only the dash couldn't connect.
Technology said:
Guy, do you have a Mac Adddress Filter area on your router?Open your router so no key is required to make a connection and after you establish a connection use the WEP or WPA2-PSK key option! Can you find your Mac address and your Phone's Ip address on your router. You can find this info on your phone also in Comm Manager> setting> Wifi> Connection Status area. There is a place on your router to put this info, so that the router will know that its ok to connect to this device with this info, I believe its in the advance area on your router and use the 10 key WEP if possible!
Click to expand...
Click to collapse
Thanks for the suggestions. I hope everyone had a wonderful holiday
I double-checked the MAC address filter - it's turned off.
I was able to connect with Open Authentication and WEP Data encryption, and if I disable security altogether. Neither of these options is satisfactory.
I also tried 'aaaaaaaa' as the key. It doesn't work in either WPA-PSK or WPA2-PSK with TKIP or AES encryption.
The warning I get when I press the connect key in the wi-fi list is -
"Cannot connect to the network. Check your network and service provider settings and try again."
Make sure the Key Index on the phone matches the Key Rotation on the router.
sesinger said:
Make sure the Key Index on the phone matches the Key Rotation on the router.
Click to expand...
Click to collapse
I don't think I'm using Key Rotation. Isn't that just for WEP? And, only if you have a RADIUS server? I just have a simple home network, nothing fancy.
I have a basic USRobotics router and it supports key rotation for WPA2. I had it set to 0 (meaning off), however there was no equivalent setting on my S621. The S621 could only be set at 1,2,3,or 4. When I set both the S621 and the router to the same number (in my case 4) I was able to connect.
My netgear doesn't have a place to set key rotation. I tried each key order (1 - 4) on the phone - no luck.
I even tried installing the evaluation version of CommView for WiFi (http://www.tamos.com/products/commwifi/) so I could see what each device is doing. But, I don't have a compatible adapter.
Your Router's IP Address Is 192.168.1.1 Not 192.168.0.1
skyguy said:
Thanks for the suggestions. I hope everyone had a wonderful holiday
I double-checked the MAC address filter - it's turned off.
I was able to connect with Open Authentication and WEP Data encryption, and if I disable security altogether. Neither of these options is satisfactory.
Click to expand...
Click to collapse
For your router with IP address 192.168.1.1 with the WPA encryption, turn on the MAC address Filter and install the phone's MAC address in the router in the appropriate area, save settings (soft reset)! Now your phone will now be able to connect to your network via wifi.........!
Well, it's working now in WPA-PSK(TKIP) mode. Here are the changes I made:
I installed a new battery (my Dash started dying every time I turned on wireless while on the battery).
I removed a network called "Free Public Wireless." The Dash would try to connect to this network when it failed to authenticate on my encrypted network.
I suspect the "Free Public Wireless" network was interfering with the login to my home network. I'm just happy that it's working.
Hi, all,
I have the same problem:-
"Cannot connect tot the network. Check your network and service provider settings and try again."
After some troubleshooting, I found that this problem will go away when I set some IP address in the network adapter.
I have confirmed that my password (network key) is correct and my MAC filter are also correct.
The only changes that I can think of is that I went to US last week and connected using hotels' wireless access. No IP settings were done during the connection.
Please let me know if anyone has any idea on how to solve this problem.
Many thanks in advance.
Joe
I have the HTC Touch HD for a few days now and I love it.
I only have the following problem with wireless network connection.
At home I am using a dynamic IP address at work an static address (wtih different DNS and gateway settings)
Does someone knows an program to set these settings for the different connections?
Thanx!
No one any idea
I think other persons will have the same problem. A tool should be available right?
you shouldn't have any issues really. It's odd that you doi. I use mine to connect to multiple wireless networks and it all works fine.
When you turn on the wireless to connect to a new network it will pop up at the bottom and tell you the networks it has found. Then you choose the network you want and connect to it. This will then store it as a favourite connection. Once this has been done whenever you turn on your wireless it will look for networks in range and then automatically connect to which ever one is in range in the Favourite connection list.
Your connection list can be accessed through Start>Settings>Connections>WiFi then Wireless networks. It may be advisable to delete them all and start again if you are having problemss.
Thanks
Dave
You're right for the wifi settings. But the ip settings (static / dynamic gateway dns) are not set through the wireless connection.
But I have found a program called wifiprofiles which does exactly what I want
Hi everyone,
I'm in a company and when i'm connecting to the network with my laptop they told me to put a default gateway 10.20.30.10. I have to put on both wireless and wired connections otherwise i wont be able to get internet. I was wondering how can i change the default gateway on my Desire so i can get wifi internet. I looked everywhere, and nobody mentioned anything like this i guess.
Thank you
You can find the gateway setting, by pressing "menu" when you are in "wi-fi settings", then choose "advanced".
OMG thank you so much, i'm sooooo stupid.
Cumpz
Hmm i put the default gateway and still no internet. I think it's because on my laptop everything else it's obtain automaticly even the IP i only have to change the default gateway. But when i'm on android, i have to put a static ip gateway and mask :S
Too bad
Edit: Done
cmd
ipconfig /all
and then put all the fields IP,Mask,gateway,DNS on android
been having trouble with wifi connecting. It was working fine... i decided to give a different rom a try (express 3.61 landscape). i couldnt get wifi to work and there were a couple things i didnt really care for, so i switched back to my energy 2/6/12 with anthrax kernel and still not connecting to wifi... well thats only partially true. I have a linksys WRT54GS2 router and i use CISCO NETWORK MAGIC to manage/monitor my network. When i try to disable the network lock to add my phone back in it just keeps searching and never finds it, but my phone will be connected to my network. As soon as I cancel the scan it drops the wifi connection. I even tried using WPS with no luck. Do you think it has something to do with updating my PRL and profile while on the Express rom? this is really annoying me.
UPDATE: I've been playing around in my routers configuration utility and i got this figured out. I jsut couldnt do it with in Network Magic. Ill post my steps incase anyone had this same issue:
1. open web browser on pc enter you address to get into your router(this is usually 192.168.1.1 on linksys routers)
2. leave the user name blank and type admin in the PW section(unless you changed it when you did setup)
3. Go to the "wireless" tab
4. Then goto "wireless MAC filter" subtab
5. click edit mac filter list button
6. get your phones mac address( menu\settings\about phone\hardware information
7. enter phones mac address into an open slot then click save settings at the bottom of the page. then save the changes in the router setup.
It may vary some for different routers but this worked for me... WHAT A PITA!