Develop Bugs

WPA Authentication Key

Where the hell is it?
After using the preferred W2003 method of tapping everything in sight in the vain hope that I might stumble across what I'm looking for, I've failed miserably. So, having configured my shiny new router for WPA encryption, how the bl**dy hell do I configure the XDA2s to talk to it via WPA?

crocodile said:
Where the hell is it?
After using the preferred W2003 method of tapping everything in sight in the vain hope that I might stumble across what I'm looking for, I've failed miserably. So, having configured my shiny new router for WPA encryption, how the bl**dy hell do I configure the XDA2s to talk to it via WPA?
Click to expand...
Click to collapse
Connect to your shiny new router with your XDA2s. A "window" will popup and ask you for the key.

Assuming that the PPC can use (WPA) Authentication, which I can not prove since I use 64bit (WEP) encryption. If WPA auth. doesn't prompt on your PPC, try using WEP for WiFi security on your shiny new router.

I'm using WPA-PSK with my Linksys WRT54G (Firmware v3.03.6) without problems ..
QTEK9090
ROM: 1.22.00 WWE
RADIO: 1.10.00
PROTOCOL: 1337.391
EXTROM: 1.22.557 WWE (cooked)
BT: 3500 (with patch)

Yes, but is your router shiny?

Try putting the WINS address "192.168.0.1" or whatever address of your router is.
Also some devices would only accept the Hex variety of the key you choose.
Good luck.

I have a similar problem. I have a linksys wireless router set to secure.
My SX66 asks me for the password. When I enter it I get an error message that it is not the correct password.
The SX66 then says it is connected to the network and shows the SSID and other details, but other than this message it doesn't seem to be connected and I cannot connect to the internet.
What am I'm doing wrong?

To get to the options:
1) turn on the wireless
2) wait for it to pop up asking you if your router connects to "work" or the "Internet". I assume you will want to click "work".
3) Open the wireless LAN manager
4) Click the TOOLS menu at the bottom.
5) Choose NETWORK CARDS
6) You should have a "Configure Wireless Networks" window up.
7) Tap your shiny router one time (it should say connected BTW)
Now you should have 3 tabs at the bottom, General - Network Key - 802.1x . Under the Network Key tab you should have 4 options for Authentication - Open, Shared, WPA, WPA-PSK. The data encryption option will depend on which authentication you choose. I beleive you should choose WPA for authentication and WEP for data encryption. Then put in the key. If that does not work, try TKIP for data encryption maybe.
I have not tested out any of this myself yet. I still have an old linksys running 128 bit WEP. I am getting a Sonicwall TZ-170 SP (think that is the model #) and will then try WPA and maybe even see if I can get RADIUS working through the PDA2K.

WiFi Security
Thank you ed207_us for those instructions!!! They helped so much.
For everyone's general consumption, I thought y'all might be interested in WiFi security:
http://windowssecrets.com/comp/050526/#story1
(towards t e bottom of the page -- it's worth looking for)
http://blogs.zdnet.com/Ou/index.php?p=43
I just got my home WiFi network running; this is so cool!

Unable to connect Wireless Lan when phone signal is weak?

Hi,
I'm experiencing a weird problem and please let me know if it's only my problem or there is some work around for it.
My phone is SX66 upgraded to 1.40 ROM + 1.13 Radio stack
I can connect Wifi fine whenever I have some phone signal (at work). Whenever I go home where the phone signal is weak then the WIFI couldn't get connected (I believe I set up my home network correctly as I've been using it for so long and configure it for several computer/laptop in house). The network could detect the AP with the SSID but I just couldn't connect to it even I'm sitting right next to the AP.
ROM 1.40
Radio: 1.13
MDD

Are you sure it isn't connecting? What has led you to this conclusion?
Is it possible that it is connecting, but that you just can't browse the internet, in which case check your connection proxy settings. If your work uses a proxy server and you've enabled the pass-through setting in ActiveSync, your network connection may be configured with your work proxy server.
If you're sure you're just not connecting however, things to check are;
WEP/WPA Encryption - If you're using it and have other wireless devices on your network, you no doubt know what to do. If not, say so & I can help you.
DHCP - Does your router/AP support Auto-IP Addressing? Is it enabled? If not, you'll have to configure the WiFi card with a static IP within the same subnet as your router. Ask if you need help.
MAC Filtering - Are you blocking unauthorised MAC Addresses (on your router/ap)?
Interference - Wireless A/V Senders and digital cordless phones are common culprits for RFI. 802.11x APs support multiple channels (most default to channel 11), and you can change these in case of interference. Once again, if you have other WiFi gear already connected with good, strong signals, you can probably discount this one.
Sorry if this is all elementary to you - I don't know how technical you are.

Thanks for your reply.
> Are you sure it isn't connecting? What has led you to this conclusion?
Yes, I've check wireless status on the phone. "Connected to the network", and the AP with DHCP on showed the status of an IP has been allocate to the SX66 mac address. However I dont' really believe it then I check the "Adater", it said network available, and the WIFI icon just didnot show any traffic.
> Is it possible that it is connecting, but that you just can't browse the internet, in which case check your connection proxy settings. If your work uses a proxy server and you've enabled the pass-through setting in ActiveSync, your network connection may be configured with your work proxy server.
I've experience once with the internet connection via Active Sync so I disable the passthrough. Both home and work doesn't have proxy server so I selected not to have any on the phone.
> WEP/WPA Encryption - If you're using it and have other wireless devices on your network, you no doubt know what to do. If not, say so & I can help you.
At work, I have 128 WEP and the connection works fine with the key. At home, I open my network but using MAC filtering to protect it. I have problem with the open network one at home. Perhaps, I will try to setup WEP at home and see if it can work.
The only thing I'm not really clear is the difference between setting "WPA" and "WPA-PSK" from the phone.
> DHCP - Does your router/AP support Auto-IP Addressing? Is it enabled? If not, you'll have to configure the WiFi card with a static IP within the same subnet as your router. Ask if you need help.
Yes, DHCP enable as I don't want to change it back and forth when traveling.
> MAC Filtering - Are you blocking unauthorised MAC Addresses (on your router/ap)?
I do it and I already opened the network and then captured the MAC address into the AP memory. (that's why I think it's connected but will check).
> Interference -
Not really, I'm 6' away from the AP and I don't have any cordless device in my computer room.
> Sorry if this is all elementary to you - I don't know how technical you
are.
No problem, I'd like to learn more about this PDA. The concept is about the same with PC, but the tools to debug is not there. I can't use tracert/traceroute, ifconfig or ping broadcast to really know if I'm the network.
Once again, thanks a lot.

Okay, well it sounds like you're on the right track & know what you're doing.
A useful troubleshooting tool, which gives you tracert, ping, whios, ipconfig and a host of other tools is "vxUtil", which is freeware. I'd give you a URL for downloading it, but I'm on my iMate now (sipping coffee by the Yarra in a Melbourne Cafe - oh what a techno-wanker am I!), but search these forums or Google it and you'll find it.
Now, regarding the proxy thing... These PPCs are a little tricky with their internet settings, and I had to create a different 'connect using...' connection profile, if that makes sense. The important setting within the profile, which is under the Proxy tab, from memory, is "This network connects to the internet".
Now for some reason, if you don't enter in a proxy server here, that check-box doesn't stay checked when you ok your way out. So what I've had to do is go into the advanced area & enter anything in the "wap" proxy, then ok out.
Strange, but it seems to work. Although I always leave my "Private network" on "My Work Network", I can now browse the 'Net through the WiFi AP/Router.
Download vxUtil & see if you can ping your AP, then go from there.

I've worked around the problem by using static IP address instead of depending on DHCP. Thanks to Hitchhiker software. I noticed that it was trying to obtain IP address from DHCP but failed. (The very same DHCP work wells for the rest of my network). Anyway, I will use Hitchhiker to switch IP back and forth if necessary.
Thanks a lot!
MDD

Great to hear you found the problem - well done.

Can't connect to my home wireless router.... help please

Hey
I just got this phone.
Anyways, thought it'd be great to connect to my home internet.
We have an Airport Base Station. It's passworded with WPA Personal.
Anyway, it goes to connect, says I need a network key. I type the password in and it fails to connect. I figure I need to set it to WPA.
I go to configure and then click my router in the list.
In 'General' Tab I've got it as 'connects to the internet'.
In Network key I'm pretty sure i've tried them all. Some settings has the network key grayed out. Other settings I type it in, click ok and it INSTANTLY says the network key isnt correct. Wouldn't it need a moment to verify with the router if I'm typing the right password?????
Anyway I think I've tried all combos. Then when I click my router and hit connect, it says connecting for a moment, then goes back to available.
Any ideas?
I did a hard reset. I havent updated the ROMs or anything yet... would that be wise?
Cheers

bt home hub2 connects but no net
I am wirelessly connected to our BT homehub2 network, but cannot use internet explorer, all the wpa, channel, passkey's etc are the same?
O2xda2s on T-mob rom 2003 2GbSD - Pre-pay O2sim

Last I checked, the angel only supports 802.11B, not G.
No G = no WPA, only WEP.

hmmm
but it has WPA settings in the network key tab?
also it refers to it as 802.11X I think?

ok guys do not confuse encryption with network speed, personally i use in my BA and router with setup WPA PSK (Personal Key) with TKIP encryption, secure and compatible solution
if encrypption is WPA2 the BA will not connect

xplode said:
ok guys do not confuse encryption with network speed, personally i use in my BA and router with setup WPA PSK (Personal Key) with TKIP encryption, secure and compatible solution
if encrypption is WPA2 the BA will not connect
Click to expand...
Click to collapse
Shows how long it's been since I updated my angel then, I was not aware that a WPA stack had been added to the available ROM's.

Desire: Connecting to WiFi Unsuccessful [SOLVED]

Hey everyone,
I just got a brand new HTC Desire yesterday and I can't seem to connect my phone to the internet via WiFi. I don't know why but I entered the right password and everything... Every time it goes 'Obtaining IP address from (router name)', but ends up unsuccessful. I tried forgetting and doing it again but still does not work. Anyone have any ideas? Please let me know what information I should post to solve this matter quicker. I'm running on 2.1 update1
[SOLVED]

It seems that most HTC Android phones are very fussy about the routers they will reliably connect to. Whether it's a really a phone problem, or the router that is at fault isn't really known.
Try changing the channel and/or encryption method on your router, as this may help.
Regards,
Dave

Solution
I found my way around solving this issue. Here's how I solved my problem:
Problem: Unable to connect to WiFi. Able to scan network but 'Unsuccessful' everytime WiFi attempts to 'Obtain IP Address from (network name)'.
Solution:
1) Press Menu key under WiFi window on HTC Desire
2) Choose Advanced Settings
3) Under IP Settings, Check 'Use Static IP'
4) Insert all the information below that: IP address, Gateway, Netmask, DNS1, DNS2 (it should all be in numbers)(I only had one DNS1, so I typed the same numbers in DNS2)
You can get the information via Laptop:
Right Click on your network>select 'Status'>select 'Details' under signal quality>All the information you need
5) Once all information is filled in, press 'Return' key and it SHOULD connect successfully.
Additional Notes: I selected the WiFi network and entered the passkey before I did all the steps above.
Hopefully this helps those who had the same problem I did!

Haven't you just given your Desire the same IP address as your laptop??
If your wireless network is set up to use DHCP, you shouldn't need to do any of this.
Regards,
Dave

I dont understand why also but IT WORKS! Rightfully, mine is running on dynamic IP. Will it have any problem connecting again once IP address is refreshed?

jxleung said:
I found my way around solving this issue. Here's how I solved my problem:
Problem: Unable to connect to WiFi. Able to scan network but 'Unsuccessful' everytime WiFi attempts to 'Obtain IP Address from (network name)'.
Solution:
1) Press Menu key under WiFi window on HTC Desire
2) Choose Advanced Settings
3) Under IP Settings, Check 'Use Static IP'
4) Insert all the information below that: IP address, Gateway, Netmask, DNS1, DNS2 (it should all be in numbers)(I only had one DNS1, so I typed the same numbers in DNS2)
You can get the information via Laptop:
Right Click on your network>select 'Status'>select 'Details' under signal quality>All the information you need
5) Once all information is filled in, press 'Return' key and it SHOULD connect successfully.
Additional Notes: I selected the WiFi network and entered the passkey before I did all the steps above.
Hopefully this helps those who had the same problem I did!
Click to expand...
Click to collapse
A BIG THANK YOU..have been trying to connect with all possibilities minus setting up the static as Im using dynamic which doesnt make sense.

Keep in mind that you have to give all your devices on that network then a static ip-adres, because otherwise you run the risk of another device already having the ip you assigned to your phone.

So is there a valid (non-static IP) solution????
I just got this problem both at home and at other places as well.
I can't find any errors in Android, and wifi scans as it should, it connects but as the topic starter stats, it can't assign an IP-adress!
Static IP is not a solution for me, nor should be for anyone, this is basic function that should work with out issues.
Please advise if there is any, thanks in advance!

Connecting to Wifi Unsuccessful [NOT SOLVED]
boas said:
Static IP is not a solution for me, nor should be for anyone, this is basic function that should work with out issues.
Please advise if there is any, thanks in advance!
Click to expand...
Click to collapse
I was able to connect but noted that my phone wouldn't even completely charge, got hot and emptied in about an hour, so I installed "Startup Auditor" and" JuiceDefender" but somehow these seem to have broken the Wifi. I uninstalled JuiceDefender and there's nothing disabled in Startup Auditor that could explain it. But the phone can see Wifi points, but can't connect.
Wassup?

Of course it's possible that as the phone is rooted, juicedefencer changed something as root and I have no idea how to change it back.

glad u got it fixed!

[Q] Wifi connected but no internet . please help !

My wifi at home worked perfectly fine until about a week or two ago. Since then when I connect to my home wifi it appears to be connected with 5 bar signal but the internet is not working . Sometimes I have internet for few seconds, but than it's gone.
I tried 3 different roms including stock , viperx and cyanogenmod 11 all with the same problem.
What do you suggest me to do ?

are you sure it's not a router issue?

lukes91 said:
are you sure it's not a router issue?
Click to expand...
Click to collapse
I just tried to use my laptop as a wifi hotspot and it worked so the router seems to be problematic .
But I have 2 laptops connected to the same router and are working fine.
Maybe some bad settings
My router uses Openwrt with most settings default.

r33fd said:
I just tried to use my laptop as a wifi hotspot and it worked so the router seems to be problematic .
But I have 2 laptops connected to the same router and are working fine.
Maybe some bad settings
My router uses Openwrt with most settings default.
Click to expand...
Click to collapse
check if something like parental control is enabled or if the hox mac number is blacklisted... check also if there are conflicts in dhcp and ip reservation....

I would disable DHCP in your phone and put a static ip.
Hold down on the network name till a windows pops up then go on Modify Network>Show Advanced Options>Ip Settings>Static
IP Address: 192.168.x.128 (The X depends on what range your router is. Just do an ipconfig on your laptop to see, 1 is the most commonly used)
Gateway: 192.168.x.x (That is your router address do ipconfig on your laptop to find the 'Default Gateway'
DNS 1: 192.168.x.x (Same as the router as most routers have their own DNS)
DNS 2: 8.8.8.8 (I normally put google's )

Kahun said:
I would disable DHCP in your phone and put a static ip.
Hold down on the network name till a windows pops up then go on Modify Network>Show Advanced Options>Ip Settings>Static
IP Address: 192.168.x.128 (The X depends on what range your router is. Just do an ipconfig on your laptop to see, 1 is the most commonly used)
Gateway: 192.168.x.x (That is your router address do ipconfig on your laptop to find the 'Default Gateway'
DNS 1: 192.168.x.x (Same as the router as most routers have their own DNS)
DNS 2: 8.8.8.8 (I normally put google's )
Click to expand...
Click to collapse
Thanks for suggestion. Unfortunately It still doesn't work. It have internet access for a few seconds after I connect but then
it's gone.
lukes91 said:
check if something like parental control is enabled or if the hox mac number is blacklisted... check also if there are conflicts in dhcp and ip reservation....
Click to expand...
Click to collapse
I wasn't able to find parental controls on my openwrt router firmware. I am pretty sure mac filtering is not enabled.

try to hard reset the device...