I know theres a similar thread with only 4 replies.
a: i re opened the phone disconnected and made sure the screen was properly conected.
b: yes the buttons do respond to touch
is there a piece of code or something that will re enable the lights to go off. Ive had issues with the phone before thinking it was the hardware but it was indeed code...(i.e charging port. on and off button) thought it was the hardware but it was just bad code...
has anyone seen this and been able to make them light up again?
thanks!
You probably damaged the ribbon cable, they are very sensitive. If they still respond to touch, that means only one of the contacts is bad.
I know the answer
I have wondered the same thought but I have found the answer . I replaced ky EVO screen 2 months ago . It was glass only replacement first time for this device. So got the whole thing apart and connected it. successful onto Tue touch and all but i notice the lights so taken a look at the of screen their are clear caps under the touch button and the cap had a tail and it lead to device and it is where the light is in the device so I took each cap off and cleaned it up and put it on at first no epoxy or holding agent and i got the light but i suppose if u use a clear epoxy at the bottom of the screen it may have desired effect
Related
So my phones earpiece began to cut in and out, which I found to be a chafed and broken flex cable. No biggie, I ordered a replacement piece and waited for it to show. As I waited the phone began to get worse, I lost the earpiece entirely, the leds stopped working as well as the sleep button. The screen, now only able to be woken by sliding, would not come on when slid out, but only once it returned..also the screen would shut off when I would slide it out again.
I have seen disassembled the phone again and installed the new cable and all is well, with one exception. The slide function of the screen no longer works, period. It will not wake, it will not rotate, and the keyboard doesnt illuminate unless I press a key. I have been through this phone 4 more times now and I simply cannot pin down exactly what tells the phone that it has been slid. I have heard talk of magnets, but found no sensor or magnet, I saw small contacts..that are all functioning properly. There is no cable or connection to the screen portion that connects to any sort of switch that I can see.
Does anyone know what triggers the slide?!
Sorry mate, im not an expert but I thought this may help.
https://fjallfoss.fcc.gov/oetcf/eas...e=N&application_id=259614&fcc_id='NM8RHOD300'
The link is to the FCC website showing links to internal photos of the phone, SAR values, micellaneous stuff, etc.
Maybe a different perspective of the phone might help.
Hope this helps you
Hey guys, I cracked the screen on my HOX so I replaced the screen with a unit from directfix.com
After double checking all of the flex cables I tried to power the phone on and I am getting nothing from the screen and the vibration motor is constantly buzzing.
The only signs of life is the red LED, the three capacative buttons will light up, and the aforementioned constant vibrating. If i hold the power button to attempt to turn it off the buttons blink several times then it seems to stay on after that.
Has anyone heard of a problem like this before? Its killing me not having my HOX! I had to put my sim card in my old iphone 3gs and I have to say that this sucks really bad.
Are you sure you've connected everything correctly? It sounds like there's something being shorted! I'd recommend you to dissassembly again, an assembly again BUT THIS TIME VERY CAREFUL. Best is if you use a video tutorial if you think you're not experienced enough.
nitrous² said:
Are you sure you've connected everything correctly? It sounds like there's something being shorted! I'd recommend you to dissassembly again, an assembly again BUT THIS TIME VERY CAREFUL. Best is if you use a video tutorial if you think you're not experienced enough.
Click to expand...
Click to collapse
Thank you for the advice. I disassembled the phone and carefully put it back together. I took care to make sure the flex cables for the LCD, vibrator/button strip, antenna, volume buttons and digitizer were all carefully connected.
Now the vibrate function seems to work fine as it just gives me a short pulse when I turn the phone on as it usually does. The screen however, still refuses to turn on. I made extra sure that its flex cable was put in the right way and that it was secured with the jaw bone connector.
This video here www youtube com/watch?v=OIeO0DueMcg&feature=youtu.be at about 6:00 shows that you can test the LCD midway through the assembly process.
I tried exactly that and the LCD would still not turn on. I am just hesitant to return it because I know that the chances of the screen being a complete dud are very slim.
Now when the phone is turned on the three capacitive buttons remain on which I know didn't used to happen.
Swilli89 said:
Thank you for the advice. I disassembled the phone and carefully put it back together. I took care to make sure the flex cables for the LCD, vibrator/button strip, antenna, volume buttons and digitizer were all carefully connected.
Now the vibrate function seems to work fine as it just gives me a short pulse when I turn the phone on as it usually does. The screen however, still refuses to turn on. I made extra sure that its flex cable was put in the right way and that it was secured with the jaw bone connector.
This video here www youtube com/watch?v=OIeO0DueMcg&feature=youtu.be at about 6:00 shows that you can test the LCD midway through the assembly process.
I tried exactly that and the LCD would still not turn on. I am just hesitant to return it because I know that the chances of the screen being a complete dud are very slim.
Now when the phone is turned on the three capactive buttons remain on which I know didn't used to happen.
Click to expand...
Click to collapse
Update: So I was thinking the phone was booting up all the way, but I just saw that my computer won't recognize the phone beyond making a connection sound; I just can't see it in windows. As i said the capacitive lights stay on, but if I fold the power button they blink 15 times exactly and the phone seems to power off. Should I assume the SoC is dead or gamble with a replacement LCD?
Swilli89 said:
Update: So I was thinking the phone was booting up all the way, but I just saw that my computer won't recognize the phone beyond making a connection sound; I just can't see it in windows. As i said the capacitive lights stay on, but if I fold the power button they blink 15 times exactly and the phone seems to power off. Should I assume the SoC is dead or gamble with a replacement LCD?
Click to expand...
Click to collapse
Hi, I'm in the exact same situation you have described above! Did you ever manage to work it out, what was the solution? Any info or help at all would be great, thanks!!
I did replace my lcd+digitizer as well as yous. And I had same problem. But it does work now.
1.open up your phone . Take all parts off, separated.
2. Take battery off.
3.Now connect power button.
4. Connect battery.
5.Switch it on (hold pwbt for 2sec), mobo+battery+power button itself.
6.Now wait 20 sec.
7.Now connect LCD ribbon(bottom one),make sure it's right in, push it in far as you can.
8.Now put it righ on bezel and connect digitizer ribbon.
9.Press pwbt and see does it work. If does put rest of stuff together and be happy.
I can make phototutorial on request.
I did it few times. The battery was touching the LCD ribbon and it comes of very little but screen comes off and I have to start all over again.
So make sure that ribbon it's not getting any pressure from battery.
Let me know does that help.
Sent from my repaired HTC One X
Please excuse this repost.
At first my phone would boot and the soft keys would light up and the LED would shine while charging. Shortly after that, I had no display and no illumination whatsoever on my screen. I just disassembled the phone to make sure all of the bands and connecters are connected and they are fine. I have reason to believe the screen works because when I receive a call, i can press where I usually would to accept calls and it works.
I opened up my phone and found the Slide Flex Cable was detached and I'm ready to try to get this fixed finally.
I found the replacement ribbon for about $15, but I also am finding broke devices for only a little more cost. Do you think it would be wise to go ahead and get a scrap Epic 4g and get the cable out of it? I could also use some other parts of hardware anyway. Any suggestions?
It would probably be easier to get a scrap with a working screen and switch motherboards. So much simpler.
Sent from my SPH-D700 using Tapatalk 2
Yesterday i dropped my device from one feet. It turned off and i turned it on.
Now lower part of screen and capacitative buttons dont work. i will attach a image(non-working area outlined in red)
My warranty has expired so i cant exchange it for a new one. What should i do? Can i fix it by myself?
Please help me
Fycola123 said:
Yesterday i dropped my device from one feet. It turned off and i turned it on.
Now lower part of screen and capacitative buttons dont work. i will attach a image(non-working area outlined in red)
My warranty has expired so i cant exchange it for a new one. What should i do? Can i fix it by myself?
Please help me
Click to expand...
Click to collapse
Hi,
Only thing I can think of is that somehow it has damaged the cable from the touchscreen or the tiny wires that feed into the cable without damaging the screen. I came across a brand new screen I was replacing once for someone that had a similar problem where the bottom left hand corner wouldn't respond to touch unless there was firm pressure on the screen to create contact, and this was a brand new screen. It could also be that the touchscreen connector needs to be pushed back onto the board if it's come a bit loose.
If this is the problem, you can fix it by yourself although I'd have a good look around youtube, there are heaps of DIY videos of how to replace screens. If you do go down this path I recommend you replace the touchscreen/LCD/LCD frame in one go, as it's generally already pre- assembled the only thing here is that there are 3 brands of LCD's HTC used with the phone and they aren't all compatible, and you can only tell by pulling down your phone and looking at the LCD flex cable colours, and the other thing is that the screens that are available aren't always the same quality as the original. If this sounds to hard your best bet is to take it somewhere and diagnose the problem just in case it's something else
Its been some days, I'm experiencing this weird touch screen problem.
My DZ touch screen doesn't respond properly.
For example:
If i see an image and slide just one finger up and down then it would zoom in and out. And then the whole screen becomes unresponsive.
It seems as if, its touched by itself. Even the softkeys would go numb. Only the haptic feedback of my search button works at that moment.
But the trackpad works perfectly.
But, If i lock and unlock the screen using power buttons, it would work properly for some few moment and then again the problem repeats.
At present I'm repeating this process of locking and unlocking screen to use my phone.
One even worst weird thing is that, if the device is connected to a charger and kept on the table or floor. This problem doesn't occur.
I have done system format, restored my nandroids and even changed Roms. The problem still exists.
Please note, i don't use any Casing or covers that would press the device hard for malfunctioning of screen. I have even removed and replaced my screen guard.
I'm sure, its not a software issue.
And even i dont think its a strip issue, because i dont use my physical keyboard always.
Can anyone say what hardware issue it might be..?
Or what i need to do? I'm really out of options.
Do i have to replace my whole screen or the digitizer..?
Thanks...
Thats no fun,
As you stated it's more than likely a hardware fault, the two most likely culprits would be the digitizer or the main flex cable
Which would be this and this
both relatively easy to replace depending on your experience
in 4.x and up ROMs check the developers setting to show touch or use apps like
z device test
or
yet another multitouch test
these wont help you fix the issue but may show you where the bad points are on the screen
best of luck
I know the problematic spot. Its near Search softkey. Even Yet another multi-touch test would stuck at that spot....
As you can see in the image, that i'm not holding anywhere, still it shows that somewhere around Search softkey its touched by itself.
In second image, If i move my fingers around, it would show the other touch responds, but if i slide near search, it would go and stuck there itself.
So, i guess i would first go with the flex cable.
In actuality I'm leaning toward the digitizer in your case, but its possible to be either.
And if you have a spare phone it may be worth disassembling even without buying anything. On a G1 I once fixed a similar issue just taking out the digitizer and cleaning the contacts on the ribbon and the edges of it as well, when I put it back it worked like new. I think some dust may have gotten into the edges but it may be worth a shot before buying anything... But could make matters worse so if you don't have a spare, buy parts first
Best of luck
Sent from my Nexus 7 using XDA Premium 4 mobile app
I guess i should try disassembling and clean it first. If it still persists then i would go for digitizer.
And thanks for giving a hope.
Thanks...