How to hardware reset Touch Pro2?
RHOD100 MFG 32M SS-BC 0.74.1000
I recive answer from HTC:
The way you do a hard reset on a touch Pro 2 is :
1. With the device turned off, press and hold the VOLUME UP and VOLUME DOWN buttons, then briefly press the POWER button.
2. Continue pressing the VOLUME UP and VOLUME DOWN buttons until you see this message on the screen:
3. Release the VOLUME UP and VOLUME DOWN buttons, press the VOLUME UP button to perform the hard reset, or press any other button to cancel the reset
Thank you once again for your continued patronage.
Best regards, Europe customer support team HTC Corp. Global Service Division
But, this instruction not work.
Try holding the Vol Up and Down together and Reseting with the Stylus. (Just a guess BTW )
P.S. Did you get my PM ?
Thanks
Dave
DaveShaw said:
Try holding the Vol Up and Down together and Reseting with the Stylus. (Just a guess BTW )
P.S. Did you get my PM ?
Thanks
Dave
Click to expand...
Click to collapse
Not Work
Does it get to the point where it shows you a reset message on screen?
This is screen
Goran Anicic said:
This is screen
Click to expand...
Click to collapse
From what I've read about the Topaz:
Hold Vol UP and Vol DOWN together (keep them pressed down and do not release). Then press the reset button with the Stylus and hold it for a few seconds, then remove the stylus keeping vol up and down pressed.
Or if the device is off hold down Vol Up and Vol Down (keep them both pressed until you see the message) and then Power On.
A Hard Reset is usually a two button combo whilst the device is powering on (either from a reset or from a cold boot).
Dave
That screen reads like the software is dead due to it being a beta test.
Jacina said:
That screen reads like the software is dead due to it being a beta test.
Click to expand...
Click to collapse
Yep, but you can still Hard Reset and change the date.
Ta
Dave
I have the same problem. Can anybody PM me with a solution to this? Tried all I know and nothing works...
Ok, here it is.
To hard reset Touch PRO 2 you have to press power + start call (green) + end call (red) buttons. Hold them all and press reset button. Keep holding them untill you see screen that says to press volume up button to reset .
Ciciban said:
Ok, here it is.
To hard reset Touch PRO 2 you have to press power + start call (green) + end call (red) buttons. Hold them all and press reset button. Keep holding them untill you see screen that says to press volume up button to reset .
Click to expand...
Click to collapse
And what am I supposed to do with my other four arms whilst I'm doing that?
rb14 said:
And what am I supposed to do with my other four arms whilst I'm doing that?
Click to expand...
Click to collapse
LMAO now that just made my morning..( idont have a pro2 just skimming through threads lol but u made my day )
daeshawn said:
LMAO now that just made my morning..( idont have a pro2 just skimming through threads lol but u made my day )
Click to expand...
Click to collapse
Haha, me 2.
Think he meant to say, turn the phone off, hold start call and end call keys and then press power on while holding down the two buttons. Nothing needed with the reset button.
Ciciban said:
Ok, here it is.
To hard reset Touch PRO 2 you have to press power + start call (green) + end call (red) buttons. Hold them all and press reset button. Keep holding them untill you see screen that says to press volume up button to reset .
Click to expand...
Click to collapse
yes this is accurate and just so you guys know, this is in the manual lol.
mallman said:
yes this is accurate and just so you guys know, this is in the manual lol.
Click to expand...
Click to collapse
There is this saying amongst IT guys... RTFM = Read the ****ing Manual
hehe mostly the answer is closer than u think
Wrong post.
DELETE
mallman said:
yes this is accurate and just so you guys know, this is in the manual lol.
Click to expand...
Click to collapse
Manual? Think I threw mine away when I got it Never read the manual
Ciciban said:
Ok, here it is.
To hard reset Touch PRO 2 you have to press power + start call (green) + end call (red) buttons. Hold them all and press reset button. Keep holding them untill you see screen that says to press volume up button to reset .
Click to expand...
Click to collapse
Thanks! That did it! Team effort though!
What is this, some pre-release touch pro 2?
Is there a way to manually hard reset the TP2 w/o having to go into settings??
Please help!!
Turn off your phone completely. If buttons and touch screen become unresponsive, pull the battery out.
Hold both "send" and "end" button, then press and hold "power" button. Follow the on screen instructions.
for verizon
Hold down the end key till the device powers off, then hold volume down, send
and end till you see blue text on a white background. Follow hard reset prompt
http://forum.ppcgeeks.com/showthread.php?t=85339
I think this is for the At&t version below
1. Turn off the TP2. In my case, I had to pull the battery out since the on-off button didn't work
2. Press and hold the SEND and END keys simultaneously
3. While continuing to hold the SEND and END keys, press the POWER BUTTON (a bit of finger contortion here)
4. Press the VOLUME UP button
amurch said:
Is there a way to manually hard reset the TP2 w/o having to go into settings??
Please help!!
Click to expand...
Click to collapse
Hold the TALK, END, and backlight( on top of the phone) With the phone off till you get the reset screen. or if the phone is on then hold all 3 and use the stylus to hit the reset button till you get to the screen to reset.
Info found here
Okay i have been gone for a while but I'm hoping you guys can help me out.
Long story short i was in the Bahamas last week and got engaged. took tons of pictures with my factory note 3 tmobile. i dropped it and broke the screen. completely black screen and cracks. when i try to connect it to the laptop i can sometimes get it started to where the led turns blue and i can hear the t mobile jingle but then i get the little vibration and it feels to me like it gets stuck in a boot loop. please guys i was once a very active member and probably could figured this out on my own but i could really use some help! thanks in advanced!!!
You didn't say but my guess is that you want to recover some data.
R1. Starting with it off, press and hold the volume up and the home button, then press the power button until the short vibration. Wait about five more seconds then release the other two buttons.
R2. It should now be in Recovery mode. Try ADB.
D1. If no access through ADB then do paragraph R1 again but instead of volume up, press volume down.
D2. After releasing all buttons in D1, press and release volume up.
D3. It should now be in Download mode. Try ADB.
Frank
Frank Westlake said:
You didn't say but my guess is that you want to recover some data.
R1. Starting with it off, press and hold the volume up and the home button, then press the power button until the short vibration. Wait about five more seconds then release the other two buttons.
R2. It should now be in Recovery mode. Try ADB.
D1. If no access through ADB then do paragraph R1 again but instead of volume up, press volume down.
D2. After releasing all buttons in D1, press and release volume up.
D3. It should now be in Download mode. Try ADB.
Frank
Click to expand...
Click to collapse
Thanks brother... I'm going to give that a try
If you have an mhl adapter, you can try to connect it to your tv before you power on (while trying to boot into recovery). That might show you what would be on your screen. I have no idea though. Just a suggestion.
Sent from my SM-N900T using Tapatalk
I've noticed that holding the power button for ~10 seconds no long turns off the note for a soft reset. Is there another key combo or is it just me?
Power and volume down
Hey, so I was messing around with my phone and using TWRP, I deleted the original ROM and then, having forgotten that I'd deleted the ROM, tried to reboot the phone. My phone is now stuck on the HTC splash screen (which at the bottom has the text "This build is for development purposes only...") and won't turn off, despite me holding the power button for probably 1+ minutes. I'm planning to wait until the battery dies, then once I can boot again try to get into TWRP by holding the power button and volume down. Does anyone know if there's a way I can get to TWRP without having to wait until the battery dies (my phone is at full charge), or whether this will not work and I should try something else?
Thanks in advance!
Press and hold power & volume up buttons until the screen turn black then release both buttons and quickly press & hold volume down button only. This will get you to hboot
ckpv5 said:
Press and hold power & volume up buttons until the screen turn black then release both buttons and quickly press & hold volume down button only. This will get you to hboot
Click to expand...
Click to collapse
Thanks this worked!