Hardware reset Pro2? - Touch Pro2, Tilt 2 Windows Mobile General

How to hardware reset Touch Pro2?
RHOD100 MFG 32M SS-BC 0.74.1000

I recive answer from HTC:
The way you do a hard reset on a touch Pro 2 is :
1. With the device turned off, press and hold the VOLUME UP and VOLUME DOWN buttons, then briefly press the POWER button.
2. Continue pressing the VOLUME UP and VOLUME DOWN buttons until you see this message on the screen:
3. Release the VOLUME UP and VOLUME DOWN buttons, press the VOLUME UP button to perform the hard reset, or press any other button to cancel the reset
Thank you once again for your continued patronage.
Best regards, Europe customer support team HTC Corp. Global Service Division
But, this instruction not work.

Try holding the Vol Up and Down together and Reseting with the Stylus. (Just a guess BTW )
P.S. Did you get my PM ?
Thanks
Dave

DaveShaw said:
Try holding the Vol Up and Down together and Reseting with the Stylus. (Just a guess BTW )
P.S. Did you get my PM ?
Thanks
Dave
Click to expand...
Click to collapse
Not Work

Does it get to the point where it shows you a reset message on screen?

This is screen

Goran Anicic said:
This is screen
Click to expand...
Click to collapse
From what I've read about the Topaz:
Hold Vol UP and Vol DOWN together (keep them pressed down and do not release). Then press the reset button with the Stylus and hold it for a few seconds, then remove the stylus keeping vol up and down pressed.
Or if the device is off hold down Vol Up and Vol Down (keep them both pressed until you see the message) and then Power On.
A Hard Reset is usually a two button combo whilst the device is powering on (either from a reset or from a cold boot).
Dave

That screen reads like the software is dead due to it being a beta test.

Jacina said:
That screen reads like the software is dead due to it being a beta test.
Click to expand...
Click to collapse
Yep, but you can still Hard Reset and change the date.
Ta
Dave

I have the same problem. Can anybody PM me with a solution to this? Tried all I know and nothing works...

Ok, here it is.
To hard reset Touch PRO 2 you have to press power + start call (green) + end call (red) buttons. Hold them all and press reset button. Keep holding them untill you see screen that says to press volume up button to reset .

Ciciban said:
Ok, here it is.
To hard reset Touch PRO 2 you have to press power + start call (green) + end call (red) buttons. Hold them all and press reset button. Keep holding them untill you see screen that says to press volume up button to reset .
Click to expand...
Click to collapse
And what am I supposed to do with my other four arms whilst I'm doing that?

rb14 said:
And what am I supposed to do with my other four arms whilst I'm doing that?
Click to expand...
Click to collapse
LMAO now that just made my morning..( idont have a pro2 just skimming through threads lol but u made my day )

daeshawn said:
LMAO now that just made my morning..( idont have a pro2 just skimming through threads lol but u made my day )
Click to expand...
Click to collapse
Haha, me 2.
Think he meant to say, turn the phone off, hold start call and end call keys and then press power on while holding down the two buttons. Nothing needed with the reset button.

Ciciban said:
Ok, here it is.
To hard reset Touch PRO 2 you have to press power + start call (green) + end call (red) buttons. Hold them all and press reset button. Keep holding them untill you see screen that says to press volume up button to reset .
Click to expand...
Click to collapse
yes this is accurate and just so you guys know, this is in the manual lol.

mallman said:
yes this is accurate and just so you guys know, this is in the manual lol.
Click to expand...
Click to collapse
There is this saying amongst IT guys... RTFM = Read the ****ing Manual
hehe mostly the answer is closer than u think

Wrong post.
DELETE

mallman said:
yes this is accurate and just so you guys know, this is in the manual lol.
Click to expand...
Click to collapse
Manual? Think I threw mine away when I got it Never read the manual

Ciciban said:
Ok, here it is.
To hard reset Touch PRO 2 you have to press power + start call (green) + end call (red) buttons. Hold them all and press reset button. Keep holding them untill you see screen that says to press volume up button to reset .
Click to expand...
Click to collapse
Thanks! That did it! Team effort though!

What is this, some pre-release touch pro 2?

Related

Motorola Q9H Hard Reset

Hey guys,
I had a quick search through the forum here and i couldnt see it posted,
My boss's q9h wouldnt boot up so i had to figure the hard reset function with keys.
Incase anyone needs it:
Turn device off
Press and hold the "E" and "Z" keys
Press Power button once
When screen comes on, let go of "E" and "Z"
Press Power button once again.
There should be a black message atop the screen saying reset activated.
Then wait several minutes while it resets itself to factory.
Hope this helps someone.
thank you very much, got mine done as well
cheers
Thanks MAN..
Thanks man its work
djcreedy said:
Hey guys,
I had a quick search through the forum here and i couldnt see it posted,
My boss's q9h wouldnt boot up so i had to figure the hard reset function with keys.
Incase anyone needs it:
Turn device off
Press and hold the "E" and "Z" keys
Press Power button once
When screen comes on, let go of "E" and "Z"
Press Power button once again.
There should be a black message atop the screen saying reset activated.
Then wait several minutes while it resets itself to factory.
Hope this helps someone.
Click to expand...
Click to collapse
Thanks man its work
djcreedy said:
Hey guys,
I had a quick search through the forum here and i couldnt see it posted,
My boss's q9h wouldnt boot up so i had to figure the hard reset function with keys.
Incase anyone needs it:
Turn device off
Press and hold the "E" and "Z" keys
Press Power button once
When screen comes on, let go of "E" and "Z"
Press Power button once again.
There should be a black message atop the screen saying reset activated.
Then wait several minutes while it resets itself to factory.
Hope this helps someone.
Click to expand...
Click to collapse
thak you man gert job............
thaks
Thanks for the help bro

Manual Hard reset??

Is there a way to manually hard reset the TP2 w/o having to go into settings??
Please help!!
Turn off your phone completely. If buttons and touch screen become unresponsive, pull the battery out.
Hold both "send" and "end" button, then press and hold "power" button. Follow the on screen instructions.
for verizon
Hold down the end key till the device powers off, then hold volume down, send
and end till you see blue text on a white background. Follow hard reset prompt
http://forum.ppcgeeks.com/showthread.php?t=85339
I think this is for the At&t version below
1. Turn off the TP2. In my case, I had to pull the battery out since the on-off button didn't work
2. Press and hold the SEND and END keys simultaneously
3. While continuing to hold the SEND and END keys, press the POWER BUTTON (a bit of finger contortion here)
4. Press the VOLUME UP button
amurch said:
Is there a way to manually hard reset the TP2 w/o having to go into settings??
Please help!!
Click to expand...
Click to collapse
Hold the TALK, END, and backlight( on top of the phone) With the phone off till you get the reset screen. or if the phone is on then hold all 3 and use the stylus to hit the reset button till you get to the screen to reset.
Info found here

[Q] Volume up + Volume down

Hey lads,
this is probably a very dumb Q, but since I am new to all this android schmuzzle and couldn't find ballocks on that, don't judge me too hard ;]
I've noticed that when u press both VolUp and VolDown ( put pressure kinda in the middle or the rocker ) the phone vibrates once and then after several seconds (seems to vary) it vibrates three times fast. Now what the flick is that? Not that much of a big deal but it gets annoying given that even when the screen is off and the phone is locked doesn't seem to give a damn
thanks
has happened to me too but hard to reproduce. I have no ideas why it happens. Sometimes it occurs when the phone is booting up for me as well.
Put ur finger in the middle of the rocker and press ( not even hard ). It happens every time in my case. even when the phone is locked
I get the same behaviour, sure is strange.
Kinda old thread but I didn't want to start a new one either. I've noticed this too by accident. When you turn off your screen and press both volume buttons at the same time it vibrates once and every other time twice or thrice. If it vibrates only once it will vibrate again a couple of times after about 10 seconds. Has someone found a reason to this already?
Hawks556 said:
Has someone found a reason to this already?
Click to expand...
Click to collapse
Maybe HTC thought "Why not? Let's do this and see how they discuss about it." ^^
Sent from my Desire HD
These buttons are part of combimation of three finger salute (at least look like that)...if you press voulme up + Down and power button, phone will reboot....so might be vibration is just an indicator to show go ahead and press the power button for restart.......Just a Guess
Pressing Volume Up + Down simultaneously while having USB Debugging turned on creates a bug report in the bugreports folder on your SD card.
G1sanju said:
These buttons are part of combimation of three finger salute (at least look like that)...if you press voulme up + Down and power button, phone will reboot....so might be vibration is just an indicator to show go ahead and press the power button for restart.......Just a Guess
Click to expand...
Click to collapse
I can't get it to reboot by pressing the 3 buttons.
olivierlee said:
Pressing Volume Up + Down simultaneously while having USB Debugging turned on creates a bug report in the bugreports folder on your SD card.
Click to expand...
Click to collapse
This is correct, there's always a new bugreport after I press the volume buttons. I don't think that it's even necessary to have usb debugging on.
Thanks for the quick answers, but could there be something more to it?
Hawks556 said:
I can't get it to reboot by pressing the 3 buttons.
Click to expand...
Click to collapse
Press the power button first and then press volume up and down..you will get a reboot...
Nope, can't get it to reboot. Perhaps this is rom related?
Hawks556 said:
Nope, can't get it to reboot. Perhaps this is rom related?
Click to expand...
Click to collapse
It shouldn't be, but its really hard to get it if you are trying to press three button, you can try power button and middle vol button......any ways I also tried lot of times before I got my first reboot....
1) Pressing both VOL UP & VOL DOWN at the same time = Vibrations & all processes' states and stacktraces dumped to /data/arn/traces.txt (thanks to alind_)
2) Pressing both VOL UP & VOL DOWN at the same time + POWER BUTTON once = instant reboot
Works for me with CM7 and Stock Sense.

[Q] Hard recovery reboot not working (Vup+Vdown+Pow)

Is there some secret to the Volume UP + Volume DOWN + Power hard key combo? I've pressed it hundreds of times with different timings and can't get into the bootloader. Tips?
Also, the power key takes sooooo long to turn this thing on. At first I thought it was doa. Thought that was interesting...
ronpandolfi said:
Is there some secret to the Volume UP + Volume DOWN + Power hard key combo? I've pressed it hundreds of times with different timings and can't get into the bootloader. Tips?
Also, the power key takes sooooo long to turn this thing on. At first I thought it was doa. Thought that was interesting...
Click to expand...
Click to collapse
There really isn't any secret method. Just make sure the unit is powered off then hold the power button and vol down button until you see the Android robot and you can through the options using the vol up and down keys.
[email protected] said:
There really isn't any secret method. Just make sure the unit is powered off then hold the power button and vol down button until you see the Android robot and you can through the options using the vol up and down keys.
Click to expand...
Click to collapse
Wow, I did Power + Vol Down and it worked immediately. I know I've been reading all over that its both Vol UP and Vold Down. Arggggh. :silly:
And Thanks :laugh:

hello my phone won't start

I can't start it up anymore, the screen went black and just won't turn on anymore. The computer doens't recognize the phone as a device anymore, I've tried taking the battery out and all, it was running cm12
Hold vol down + power. As soon as you see the LG logo, release both buttons and quickly hold them together again. You have to be quick. If it works that is, you'll be presented with the factory reset screen, vol buttons to highlight, power button to select good luck
speedyjay said:
Hold vol down + power. As soon as you see the LG logo, release both buttons and quickly hold them together again. You have to be quick. If it works that is, you'll be presented with the factory reset screen, vol buttons to highlight, power button to select good luck
Click to expand...
Click to collapse
nothing worked, I tried it already and stuff now this morning I removed the battery for the 10000000 time and now it did but thanks
vikke1234 said:
nothing worked, I tried it already and stuff now this morning I removed the battery for the 10000000 time and now it did but thanks
Click to expand...
Click to collapse
If you still want help to fix your phone go here and ask for help http://forum.xda-developers.com/showthread.php?t=2785089
Hope this helps you to recover your phone.

Categories

Resources