HI THERE, I WAS TRYING TO DOWNGRADE MY NEW I MATE AND SUDDENLY I GOT THIS MSG ON THE IMATE SCREEN "USB" ON THE TOP AND "V2. 06" WHILE THE IMATE IS ON THE CORDLESS. WHEN I TAKE IT OFF, IT DISPLAYS THIS MSG ON THE TOP" SERIAL" AND "V2. 06" AT THE BOTTON OF THE SCREEN . I WAS SICK OF THE CURRENT WORKING OPERATING SYSTEM AND TRYING TO DO SOME THING WITH IT.. HELP PLEASE
Do This first:
Press these 3 buttons at the same time:
Power button + Press the circle between the call answer and reject buttons + Soft Reset
Put the mobile into the cradel again and restart the (upgrade/downgrade) process.
which device do you have?
is it XDA2, XDA3 or?
if it shows 2.06 i suppose you have XDA3/Qtek909/pda2k.
right?
buzz
Can some pls help me how can I enter the bootmenu in Universal. I tried the combination given by wiki "camera + reset " but it doesnt works for me the device just soft rests. So pls can anyone help how can I enter the bootmenu pls.
thx
jeet
to get the bootloader you need to do power off + backlight + softreset.
i got the same problem as jeet got it, i cant get into the boot menu to get a sd bakup of my complete os
greetz
http://forum.xda-developers.com/showthread.php?t=549207
i know about that thread orb3000 but we dont talk about the BOOTLOADER, we talk about the BOOT-MENU where u can bakup ure ROM from current device to an SD card
i cant get into the boot menu if i push reset+camera !!!
thats the problem
grretz
didn't know Uni had a boot-menu
I believe for backing up ROM, you can use MTTY
I'm sure it's there in the wiki somewhere
Reset your device (using the SR hole) and then HOLD the camera button tight until you get the menu.
So the key thing is to HOLD the button after you hit the reset.
DOMy
you're joshing me? I have G3 and can't do that... (On WM6.51)
It simply boots up as normal. What does this 'bootmenu' allow you to do?
Can anyone help me out i was trying to downloading a new software upgrade for my mda pro and the computer froze on me no the phone is stuck with the screen saying with no light on serial at the top of it and at the bottom it say v2.01 but when i put the usb cable in or charge it it says usb on the screen instead of serial.The programme crash and now i cant ger out of that screen ive just told u about.I can do i hard restet and the light goes on saying press 0 to restore factory default and press x to exit.
When i press 0 it just goes back to the 1st screen i jst told u abt.With no light on and cant get light on or do anything with it.HELP i think when the update crashed on me it crashed the phone to and just kept on that screen with the serial on it.ACTIVE Sink will not work anymore when i put cable into the comptuer with my phone so updaing my phone agine will not work.Can anyone please point me in the right place to fix this promblem.Many thanx mono33
PS sorry it was so long winded but i needed to give you all the info possible i could give you.If there anything asle u need to know ust ask me and ill tell u what i can.Many thanx mono33
If this software upgrade was ROM upgrade, you're stuck in the Bootloader - check out the answers in the wiki and in the Universal Upgrading thread.
mono33 said:
Can anyone help me out i was trying to downloading a new software upgrade for my mda pro and the computer froze on me no the phone is stuck with the screen saying with no light on serial at the top of it and at the bottom it say v2.01 but when i put the usb cable in or charge it it says usb on the screen instead of serial.The programme crash and now i cant ger out of that screen ive just told u about.I can do i hard restet and the light goes on saying press 0 to restore factory default and press x to exit.
When i press 0 it just goes back to the 1st screen i jst told u abt.With no light on and cant get light on or do anything with it.HELP i think when the update crashed on me it crashed the phone to and just kept on that screen with the serial on it.ACTIVE Sink will not work anymore when i put cable into the comptuer with my phone so updaing my phone agine will not work.Can anyone please point me in the right place to fix this promblem.Many thanx mono33
PS sorry it was so long winded but i needed to give you all the info possible i could give you.If there anything asle u need to know ust ask me and ill tell u what i can.Many thanx mono33
Click to expand...
Click to collapse
If you have reached the bootloader mode and the word 'serial' changes to 'USB', you are in luck. Only before you connect to PC for upgrade open Active Sync on the PC and go to File / Connection Setting and UNCHECK 'allow USB connection' Checkbox. Then connect your device and follow the upgrade procedure. Actually you have posted this in the wrong forum. This should have been in the upgrade forum. Upgrade is not difficult. Please do let us know if you require any further help.
Dear all,
i've got 2nd hand xda stealth for 2 weeks, now my stealth cannot boot (black screen, call and End Button are light) after i flash my stealth with wrong ram with nb0 extension on miniSD. please any one can help me to recover my Stealth ?
sorry for my bad english.
xda stealth..
go to www.seeo2.com, download a rom upgrade utility from there.. then start upgrade procedure again. As xda stealth is a hybrid phone..dont try any custom roms on it..
thank's malhar for responding my thread.
i already download the upgrade rom from the o2 site (now is www.mwg.com), i put the rom to my SDCard, the problem is how can i enter the boot loader, in case my stealth always in blank screen with call and end button are light.
i already press press power + call + end button, but my stealth stuck on that condition. every method of flashing mode i already try but no response from my stealth.
Syaipul
oh yea malhar, for information i read the procedure for upgrading on o2 site that connect status is required for upgrading procedure in activecync, my stealth has disconnected status when i plug to my com. can i do the upgrade the rom in this case?
buddy, remove ur sd card from the device first..and then hard reset ur device by pressing reset button via stylus, then flag which is windows home key and then ok key..reset+flag+ok.. maintain the sequence..press reset first keep on pressing then flag and ok key.. it will format ur device.... then try to flash new rom on it
ok malhar, i'll try tomorrow. thanks.....1000x
sad-sad-sad
my stealth cannot boot (black screen, call and End Button are light) after i flash my stealth with wrong ram on miniSD. please any one can help me to recover my Stealth
Your SPL boot loader sounds like it is gone, formatted...
You may be able to patch it, using scripts & mtty if you can get into DL mode. Sounds like you're stuck in OEMSBL though.
help me !!!!
i have try pressing flat and ok botton to format . but nothing appear on the screen . is the other way to format or upgrade rom .
• The device doesn't boot, I see only O2 logo. Hard reset doesn't help and the Firmware update process stops with the first message?
1. turn off the device;
2. enter engineering mode;
3. in Main menu choose Boot Config;
4. in Configuration menu choose EBOOT-Launch Image;
5. turn off the device;
6. now hard reset or upgrade firmware.
Sometimes helps another method: leave the device without the battery for about 30 minutes, then turn your O2 XDA Stealth on.
• How to enter engeneering mode?
1. turn off your O2 XDA Stealth ;
2. hold Flag, OK and Camera + press and hold Power button;
3. use navigation buttons to select the settings.
Click to expand...
Click to collapse
follow this thread from YUC wm6
http://forum.xda-developers.com/showthread.php?t=352468
blank screen
for my case, i cant even see the o2 logo, only blank screen. is there any other way to reboot ?
cant see o2 logo
for my case, i cant even see the o2 logo, only blank screen. is there any other way to reboot ?
randysng said:
for my case, i cant even see the o2 logo, only blank screen. is there any other way to reboot ?
Click to expand...
Click to collapse
Have you tried removing the battery for few hours ??? Does the engineering mode work???
engineering mode
engineering mode ? how to set engineering mode ?
randysng said:
engineering mode ? how to set engineering mode ?
Click to expand...
Click to collapse
How to enter engeneering mode?
1. turn off your O2 XDA Stealth ;
2. hold Flag, OK and Camera + press and hold Power button;
3. use navigation buttons to select the settings
can u see..lights on keypad??what happens when u connect to pc..any sound or error
??
malhaar said:
can u see..lights on keypad??what happens when u connect to pc..any sound or error
??
Click to expand...
Click to collapse
i have a O2 tealth hanged on O2..... i tried hard reset but din work .... i downloaded new rom and software for updation .....but the problem is i cannot connect to pc.... active sync is installed...... plz help
khalifa_smart said:
i have a O2 tealth hanged on O2..... i tried hard reset but din work .... i downloaded new rom and software for updation .....but the problem is i cannot connect to pc.... active sync is installed...... plz help
Click to expand...
Click to collapse
It worked for me
Goto to your PDA setting and uncheck USB to PC.
Note: Check task before connecting to USB ensure no task including Active Sync.
FYI.
Im using VISTA Ultimate to update my XDA.
From WB 6.1 back to WM5. WM 6.1 too buggy and battery drained fast.
Cheers!
Please help me O2 stealth it dead not boot and blank screen .Are you Jtag for it please post it here.
i have the same problem --- my stealth is absolutely dead after using a cheap local charger
i have dismantled the board and taken some pics of the jtag connectors -- made the common LPT port jtag cable
how to proceed from here ?????
is the procedure similar to that of jtag recovery of a flame or an atom exec ??
how do i find the bootloader for O2 Stealth for flashing the NAND memomy Disk on Chip ??
please share your insights
hello i have wm6 on my ba and i wanna give hard reset!!! i don't know how! please help!!!!
Have a look here:
- http://wiki.xda-developers.com/index.php?pagename=HTC_Blueangel
- http://wiki.xda-developers.com/index.php?pagename=BlueAngel_For_Beginners
And next time try this one: http://forum.xda-developers.com/search.php
Greets Rossi
pls help~~~
where? i have ba whit wm6!!! i try all of them for there, not working! there is for ba whit wm5 or wm2003! for wm6 nothing!
helppp!!
on/off + reset button at the same time... not work!
recor+ on\off+reset =serial message on the screen ( i think that is bootloader)
anything alse i need! please helppp!!!
I can't hard reset either
I have followed all of the directions on the wiki, I have even tried to install another rom and it still will not remove all of the data, it changed the information in the about section of my settings but that's it. I want to change ROMs but it is not working. any ideas?
What version of windows is on your PC?
also try the enter BL which is on most ROMs
Hard Reset
To hard reset you do a soft reset (power + reset)
and before it shows the version numbers at the bottom you have to press Record + Camera & also power (i think) and then you come to an options screen using the record button to go down the list and camera to select you select Yes for option 2 and 3 and then hit the mail button to apply.
jidi22 said:
hello i have wm6 on my ba and i wanna give hard reset!!! i don't know how! please help!!!!
Click to expand...
Click to collapse
swick off button & rest buton in the same time but take care if is not the original windows you may have problems
Warm Boot: Reset the unit by pressing reset button.
Cold Boot: Press Power ++ Reset the unit simultaneously.
Read this. It's how to hard reset your BA. Hope it helps. Make sure you already formated the storage.
Code:
http://wiki.xda-developers.com/index...izzardUpgrade4