Blue Angel crashes - MDA III, XDA III, PDA2k, 9090 General

Well my MDAIII turns itself off or crashes. Mostly on the HTC screen from the new 6.5.5 Rom from D-Two. This problem persists since the first WM6 rom I flashed on the system.
Sometimes it crashes on the screen with the four colors. SOmetimes in the touchflo or in settings.
Everytime the screen goes black and you see some stripes. When I put out the battery and stick it back in it runs until the HTC boot logo or one of the other mentioned above.
When I clean the Registry Hive and format the Storage. The BLueAngel runs a bit longer without crashing.
The battery is still at 60 percent.
Is this a known problem?
Also I think that I need a new microphone. The one in the BlueAngel is defect. No one can hear me. When I put a Headset in to socket on top. Everything is fine.

Similar Problems
Hi,
I know, that won´t help U, but my Blue Angel has similar problems.
I´ve tried 6.1 Manila and 6.5.5.
Both run well and then, without any obvious reason I get a black screen.
In 6.5.5 the reset lead to a hang and showed R None G None D 6.5.5
After a further reset it showed R 1.1.5 G 1337.45 D 6.5.5
but it didn´t boot at all.
WLAN didn´t work at all in 6.5.5, so I´ve turned to 6.1 + Manila.
But there my device also hangs up, but I can reboot it.
Sadly the Blue Angel don´t run stable and crashes also, like in 6.5.5 without any obvious reason.
Maybe d-two can help, but I´m a new User and not allowed to post in the rom-developer forum.
Stay tuned
Greez from good old Germany

Related

Dead O2 Orbit

Need help...after 7 months of trouble free use my Orbit has suddenly died. It basically started last week where the phone would for no reason at all soft reset itself. After it booted up the clock would go back to its original setting back in 2006 & had to be adjusted again. The soft reset would happen without any pattern e.g. when I push the talk button when call comes through, when I try to open a program or even just pressing a button to wake it up from standby.
Anyway yesterday it did the same thing but this time it boots up to the O2 splash screen i.e. the blue screen with the picture of the glass building, & then just remains there with the backlight still on. I've resorted to a hard reset but again it will only boot up to the blue screen.
Any ideas?
zen123 said:
Need help...after 7 months of trouble free use my Orbit has suddenly died. It basically started last week where the phone would for no reason at all soft reset itself. After it booted up the clock would go back to its original setting back in 2006 & had to be adjusted again. The soft reset would happen without any pattern e.g. when I push the talk button when call comes through, when I try to open a program or even just pressing a button to wake it up from standby.
Anyway yesterday it did the same thing but this time it boots up to the O2 splash screen i.e. the blue screen with the picture of the glass building, & then just remains there with the backlight still on. I've resorted to a hard reset but again it will only boot up to the blue screen.
Any ideas?
Click to expand...
Click to collapse
Well... do u use any overclocking software ?? To me happend the same today morning... i used BatteryStatus overclocking tool @ 260 MHZ
I got a call from my dad, we talk about 5 minutes and than, one second to the other the MDA screen was black, made a softreset, booting to the o2 screen (i used Orbit WM6 Rom with MDA Compact III),set, made a hard renothing changes, once more booting to the Bootlogo...
Okay, so i tried it with bootloader mode and flash the rom, the same ****..., try the original TMO WM5 Rom, nothing changes... Now he show me the TMO bootscreen for more than 5 hours and backlight is also active all the time...
If i try to charge the MDA there is no LED lightening...
How have u sloved the problem ? New device ??
Thanks for your answer !
Regards,
Andy
mr.trader said:
Well... do u use any overclocking software ?? To me happend the same today morning... i used BatteryStatus overclocking tool @ 260 MHZ
I got a call from my dad, we talk about 5 minutes and than, one second to the other the MDA screen was black, made a softreset, booting to the o2 screen (i used Orbit WM6 Rom with MDA Compact III),set, made a hard renothing changes, once more booting to the Bootlogo...
Okay, so i tried it with bootloader mode and flash the rom, the same ****..., try the original TMO WM5 Rom, nothing changes... Now he show me the TMO bootscreen for more than 5 hours and backlight is also active all the time...
If i try to charge the MDA there is no LED lightening...
How have u sloved the problem ? New device ??
Thanks for your answer !
Regards,
Andy
Click to expand...
Click to collapse
I'm having a similar problem and I have posted my symptoms here (http://forum.xda-developers.com/showthread.php?t=344335) , though I never overclock my orbit before. ANyone have any solutions? Thanks in advance

TyTn sticks in flight mode is it a WM 6 ROM bug?

Mod, please move my message to Hermes WIN Mob 6 forum
I upgraded to WM 6 with the repackaged version of the ROM WM6 Dopod WWE 3.54.707.3 yesterday and mighty pleased with it, however I have one problem and I do not know if it is ROM related or just some setting I've screwed up in the process of changing a lot of settings.
When I turn off the phone in Comm manager and turn it on later the phone will not find the network and keeps asking for the phone pin. Entering the PIN you can see it searching on the antenna icon at top of the Today screen but then it just pops up the Phone PIN screen repeatedly.
The only way to get the phone back on is a soft reset. Pretty annoying as I turn off the phone regularly each day
Also I do not have the old flight mode/wifi balloon now when tapping on the antenna/wifi icons in main sceen, I assume this has been dropped from WM5?
Any ideas guys?
Al
moving to hermes.
Alabama978 said:
Mod, please move my message to Hermes WIN Mob 6 forum
I upgraded to WM 6 with the repackaged version of the ROM WM6 Dopod WWE 3.54.707.3 yesterday and mighty pleased with it, however I have one problem and I do not know if it is ROM related or just some setting I've screwed up in the process of changing a lot of settings.
When I turn off the phone in Comm manager and turn it on later the phone will not find the network and keeps asking for the phone pin. Entering the PIN you can see it searching on the antenna icon at top of the Today screen but then it just pops up the Phone PIN screen repeatedly.
The only way to get the phone back on is a soft reset. Pretty annoying as I turn off the phone regularly each day
Also I do not have the old flight mode/wifi balloon now when tapping on the antenna/wifi icons in main sceen, I assume this has been dropped from WM5?
Any ideas guys?
Al
Click to expand...
Click to collapse
Do a Hard Reset then test the ROM out for a few days. If you are not satisfied with it try one of the cooked WM6 versions (since they are superior).
Thanks
I will play with it as you suggest, also forgot to mention the keyboard no longer illuminates :-(
My radio too is an old version 1.03.03.10. Should I upgrade it first before flasing another ROM ( I have Hard Spl loaded OK)
After adding all my email settings for different accounts and loading apps I don't feel like a change of ROM for a few more days ;-)
Thanks,
Al
i think the problem is with your radio, try any radio at least 1.23 and above
I've been on WM6 since the second day I had my hermes, about 3-4 months ago. I've been on 4 or 5 different trips on planes requiring flight mode. Various LSVW and Sleuth ROMs used with various radios from 1.38 and on...
Not once, despite many layovers, have I had an issue with the phone not coming out of flight mode.
So, in my experiance, no, not a WM6 bug.
Alabama978 said:
Mod, please move my message to Hermes WIN Mob 6 forum
I upgraded to WM 6 with the repackaged version of the ROM WM6 Dopod WWE 3.54.707.3 yesterday and mighty pleased with it, however I have one problem and I do not know if it is ROM related or just some setting I've screwed up in the process of changing a lot of settings.
When I turn off the phone in Comm manager and turn it on later the phone will not find the network and keeps asking for the phone pin. Entering the PIN you can see it searching on the antenna icon at top of the Today screen but then it just pops up the Phone PIN screen repeatedly.
The only way to get the phone back on is a soft reset. Pretty annoying as I turn off the phone regularly each day
Also I do not have the old flight mode/wifi balloon now when tapping on the antenna/wifi icons in main sceen, I assume this has been dropped from WM5?
Any ideas guys?
Al
Click to expand...
Click to collapse
I have almost the same problem, but in my case it doesn't ask for PIN code. If I disable PIN request, everything is fine. Try to do the same and see if it's OK. This is the first ROM with this behaviour, but I can live with it in exchange of the amazing speed and phone respondivness !
I haven't seen this problem, but I do see a problem with opening a data connection after being in Flight Mode. It tries to connect to the provider 3-4 times (with quick connects), and then fails with an unable to connect message. At that point, I need to reset in order to connect to data again.
seems to be like the same problem that i am having!! i think its linked to the SOD bug, my herm100 continously reboots the 'radio' part of the phone.. when making a call the phone shows full signal however after placing the call the signal drops before connecting and it searches again for network... im sure that the phone is doing this whilst in standby mode too (maybe linking to the SOD problem) and since you've got you pin request on it seems to be cycling and asking for a pin code!! hope we can find a solution i've tried a few things but nothing seems to cure it!
Did anybody find a solution to this? My TyTn does the same

BA hung at startup screen!!!

Hi,
I have just upgraded my Blue Angel's (BA) ROM to the WM5 AKU3.5.2 R5 Rom Kitchen v2 last night, but start having issues already!
There are a couple of scenarios that I found the BA will hang at the startup screen when the Windows Mobile logo appears.
1. The first scenario was when I changed my battery. I turned off the screen, pull the battery out and replaced it. The BA hung!
2. I installed SPB Pocket Plus 3 and uses the embedded RESET function (icon) to restart the BA. Every single time I did it, the BA hung. (And I have tried more than 5 times. It really started to piss me off!)
The only solution that I can get back to the WM5 system was to give my BA a hard reset! The paid was to LOSE ALL the programs I have installed!
Has anyone experienced this before? What was wrong with it?! Did I do something ridiculously wrong or just another bug (a big one!) of the ROM? If it's a bug, anyone has a smarter way to get around it rather than hard resetting the BA before the fix comes out?
Many Thanks!
Spent hours on it!!!! Resolved by upgrading the ROM to the latest AKU3.5.2 R5 Rom Kitchen v2 and use the default setting with "BuildOS.exe".
Cheers

P3300 goes black??

Hey.. kan anybody help me?. My P3300 goes black several times a day?? i have flashed it back to its original ROM to check if that would help, but i didn´t.
The phone just goes black and i cant turn it on again without soft-resetting it. Sometimes the screen flicker and some stribes are showing across the screen before it turnes black??
I hope you can help me
Best regards Michael
i had the same problem, i send it to repair by t-mobile and they changed the lcd screen problem fixed
Seems to be a common problem, as I have exactly the same with my P3300. Send and email to the HTC customer support to ask if it could be a software issue (no reply yet) - but now that I read this post I guess I can send my device for repair right away...
I don't think the LCD is to blame for this issue. (why would the phone firmware "crash" - and unable to reboot ? )
@MicTh : those updates you've installed ? were they recent Mobile6 (B&B > 4.1, Vanilla 2.0,.. ?) from this board ?
I've got the same problem, T-Mobile replaced my handset twice (new IMEI) - reason "motherboard replaced" ???
I DO believe that USPL unlock is causing this problem now - too many MDA 3c's failing - while HTC 3000 / Orbits seem to run fine.
No.. I run the original WM6 ROM
No.. I run the original WM6 ROM, and I have also switched back to the one it came with, but i does not help
I'm getting this problem too... screen fades to black, and only way to re-start is to soft-reset. I have had two new motherboards in my original, and now HTC have replaced with a new unit, with factory WM6 and problem is the same. I was wondering if it was anything to do with software, as i do have a number of applications installed - but which one is to blame?
After I removed Spb Time, my P3300 works fine (for a week now)
pnyg
do I have sbp time? (is it "standard" or 3rd party s/w?) if I do, how do I remove it?
no, I've not got spb time, so its not that in my case....
I also experienced this problem when I installed Meschle 3.01 ROM. Cant remember if its vanilla or full version as I installed both.
I am now back to Original WM6 WWE from HTC. No problem at the moment.
first hang-up end with black scream
I have the same problem..I think
started with WM5 ..but even with WM6 is the same!
Problem description:
first of all app is hanging (ones a week)
first time rest ,its trying to start windows but will hang-up by start-up windows
second rest hangs on white scream (with WM version number)
further resetting doesn't help
white scream changes to black (some times in columns) and them totally black
some time the black scream is flashing
can any one help me?
i don’t know what to tray anymore? I think is some Hardware issue?
hang-up and later ended with black scream
I have the same problem..I think
started with WM5 ..but even with WM6 is the same!
Problem description:
first of all app is hanging (ones a week)
first time rest ,its trying to start windows but will hang-up by start-up windows
second rest hangs on white scream (with WM version number)
further resetting doesn't help
white scream changes to black (some times in columns) and them totally black
some time the black scream is flashing
can any one help me?
i don’t know what to tray anymore? I think is some Hardware issue?
I've had at least 3 separate P3300s with this problem. I'm sure its a hardware issue, and I have finally persuaded my supplier to refund 75% of my purchase price, so I can buy something different. I am sure HTC must know this is a problem, but the uk repair centre seem unable to fix it, presumably as its a batch problem, and all the boards they have are faulty.
i have exactly the same problem with my Dopod M70 (Artemis300). Maybe it have some problem in the motherboard design which HTC should let us know
My orbit do the same, when it boot win everythink is working fine. Someone did say: When you apply pressure, it fade to black. I think it maybe have something with the housing design or battery.
keckek said:
i have exactly the same problem with my Dopod M70 (Artemis300). Maybe it have some problem in the motherboard design which HTC should let us know
Click to expand...
Click to collapse
I think i solve my own problem, after hours, i found out when we press in the back phone, near the display cable position, the screen become black and hang immediatetly. so i try to open back cover, remove cable and motherboard. Use alcohol to clean the contact display cable then put its together. Tighten motherboard, and wow, my Dopod M700 are back to life again, now how hard i press, everything stay fine. No strange behavitor for 5 days. GREAT!!!
Hope everyone think my experience useful
Sounds great but...
Hey.. sounds great.. but i´m affraid to take mine appart.. i think it is very difficult to take the cover appart without ruin it
MicTh said:
Hey.. sounds great.. but i´m affraid to take mine appart.. i think it is very difficult to take the cover appart without ruin it
Click to expand...
Click to collapse
No it is easy(much easier than TyTN) to open Orbit/P3300, you have intructions in the wiki. First you check if you have right tools...
igord said:
My orbit do the same, when it boot win everythink is working fine. Someone did say: When you apply pressure, it fade to black. I think it maybe have something with the housing design or battery.
Click to expand...
Click to collapse
That's probably me from this post?
http://forum.xda-developers.com/showthread.php?t=290414
I find that if you apply pressure on the outside casing at approximately where the simcard would be it switches itself off....
Yes it's your post. I have same problem. My orbit is working fine all day, but it is on the desk, didn't touch it. I bought P3300 housing, so I will change it, maybe it fix a problem.

XDA Orbit not running right

My XDA Orbit went crazy today, first I couldn't start him at all, he wasn't react on "power button". After few attemts he finally started. I connected him to PC but he turned off after couple minutes. From this moment I can't start windows, it stops at starting screen (with IPL, SPL, GSM, OS). After a while screen starting to quakes (like a low frequency on CRT). I tried hard reset, it won't help and run it in bootloader mode but Orbit just reset.
Additonal info:
IPL 3.04.0001
SPL 3.04.0000
GSM 02.67.90
OS 3.4.0.0
ROM: Original WM6 from O2
Can anyone help me?
Have you tried a different barttery?
No, I didn't. I don't know anybody with artemis to borow another battery.
EDIT: I checked battery voltage, it's about 3,85V and now i noticed something, on battery sticker is printed it is for ARTE160 3.7VDC-1200mAh but on the phone it's printed ARTE200 5VDV-1A. Is that can cause the problem?
Finally I forced it to run in bootloader mode and flashed with the same O2 WM6 ROM. He started and I was abble to flash USPL and other ROM. It's better but still sometimes phone just poweroff with no reason
flisak said:
Finally I forced it to run in bootloader mode and flashed with the same O2 WM6 ROM. He started and I was abble to flash USPL and other ROM. It's better but still sometimes phone just poweroff with no reason
Click to expand...
Click to collapse
Hi
Had a similar problem!!! Try reflashing the rom....It worked for me..I used the o2 stock rom found on the the artemis wiki in the ftp section.... Can also highly recommend the Touch rom found in the windows mobile 6 section of the artemis section here..
regards
Lohtse
I bought a new battery but phone still turning off and freezes. Now I can't even turn it on, sometimes it starts but screen slowly fades away and after few seconds its only black screen with black light. It's propably a hardware problem but what?
EDIT: I started it, working fine when it's connected with pc but when I disconnect it freezes after couple of minutes.
flisak
open the device and check the screen is connected propperly, piss easy, just be very carefull.
if this does not work buy a new LCD.
Hi, I have the same problem with my Artemis, did anyone find a solution? Can be a problem with the LCD?
And plus one here. The device always turn off, and is difficult to turn on again. Rplaced battery and is the same.....
I've got an XDA Orbit that periodically hangs (full black screen and occasionally this seems to drain the battery very quickly). I've taken it apart and reseated the connectors and these all look ok.
Seems to happen when you're taking it out of a pocket to answer a call etc. Sometime it just requires a soft-reset but occasionally it just doesn't respond. In these instances I have found that twisting it slightly across the diagonal (top left to bottom right bending back slightly) and then resetting the device seems to bring it back to life and it's ok for a few hour/days again. If I leave it alone, i.e. not in my jeans pocket - it's fine, so think it's hardware related but not sure which bit is faulty - screen, touch-screen, mainboard etc.
If I bend it the same as above when it's working the screen goes screwy and causes it to crash so think it's definitely this is what's causing the device to crash. However, the clock seems to keep going (I'm assuming so as in most incidents it doesn't seem to lose the correct time - although I might just be seeing the problem the instant after it has crashed) so don't know whether the mainboard is still ok.
Just thought it might help some if you try the slight twisting described above to see if that helps with these to get them working and if anyone has any ideas how I can work out which bit of mine is faulty I'd be grateful.
when I try to flash the ROM 6.5 for my HP3300 after 4% flashing it restrats again. Pls help me out. I think this problem might be with my Ext_ROM. How to unlok EXT_ ROM
what is the best touch rom to use for my xda orbit. and where can i get it
lohtse said:
Hi
Had a similar problem!!! Try reflashing the rom....It worked for me..I used the o2 stock rom found on the the artemis wiki in the ftp section.... Can also highly recommend the Touch rom found in the windows mobile 6 section of the artemis section here..
regards
Lohtse
Click to expand...
Click to collapse
what is the best touch rom to use for my xda orbit. and where can i get it
Well it seems that I'm having similar issues with my Orbit.
I've been having problems with it for a few weeks and they seem to be getting much worse now.
Occasionally it would just lock up and freeze, but after frantic tapping it will unfreeze itself and continue working fine. But over the past few days it's been locking up regulary. Removing the battery was the only way to get it going again.
But now it just won't do anytihing. As soon as I start it up I either get a white screen (it phases in during the splash screen), or it'll start up, freezes after a few seconds, then eventually switches itself off. Hard resetting it makes no difference at all. Changing the battery didn't work either. I always keep it on charge overnight, could that be the problem? Maybe I'm just overcharging the battery (if that's even possible).
Note: As I've typed this, I've switched it on again only to find the battery's flat, even though it's been off for most of the day (I gave up trying to start it up). The battery usually lasts for the whole day - maybe even 2 days if I don't use it much. I had it on charge overnight as I said.
I'll try another battery to see if that works. If not then what can I do?

Categories

Resources