Related
Everyone has experienced some problems with their phone, whether its white screen/d-pad syndrome or some other fault.
Today my phone has decided not to turn on. It was working perfectly then all of a sudden screen went blank.
I have tried taking battery and sim card etc out and putting it back in. Phone won't even pick up charger.
I have had white screen of death before and dismantled my phone following alkizmo directions. This fixed my phone for a number of weeks, though problem started to re-appear.
Could this be whats caused my phone to switch off.
Does anyone have any ideas on how to get my phone to turn on again.
Warranty is well gone!!!
Seeing as there doesn't appear to be any ideas, I may go hunting for a new phone, though I'll probably take my hermes apart first!!
Fallen Spartan said:
....though I'll probably take my hermes apart first!!
Click to expand...
Click to collapse
Yeaaaaa, kill the bast...rd and go for Diamond
My hermes just started showing the same symptoms. None of the front buttons work, not even the leds... I took the phone apart i did the foam trick but it didn't work. However, it could be because the mail button is faulty (it doesn't click when pressed) so I've ordered a flex cable which includes that button. Its a good thing I've already pre-ordered the touch pro, so its not too much longer with my faulty hermes..
So... all of a sudden, everytime i slide the screen up, it shuts the screen off. I slide it back, hit the power button a few times, then it turns back on?
NRG GTX 5/9 release
TMO USA
Is my screen busted?
Power off your phone, remove the battery and then put it back in, making sure it fits in there snuggly.
That has happened to me, and removing/replacing the battery fixed it.
Yes, as Amy noted this behavior is often attributed to the battery not sitting exactly right in the compartment. Sometimes just popping it out and back in is enough, but some people have reported needeing to slip a small piece of paper or something similar under the battery cover as well to help keep it snug. (It seems that the sliding motion can be enough to shake the battery off the contacts if it's not secure enough).
Let us know if that clears it up
okay. what the deuce.
my tp2 just literally started doing the same.
earlier today it was perfectly fine.
but now.
i slide out the keyboard and the screen goes blank.
i tried the remove battery and restart.
didn't help.
i tried the paper between battery and cover.
didn't help either.
the screen only goes blank when completely slid out.
if i hold it open just before completely open the screen is still on.
any suggestions?
thanks.
Yea, none of those things worked. However, keeping the battery snug helped with the issue of not hearing anything through the handset.
It honestly sounds to me like both of you are dealing with a loose connection between the screen and the motherboard somewhere, either power or video feed, can't say for sure which. Unless you're willing to disassemble your rhodium (which isn't impossible, just complex), it sounds like it's time to send it to a service center (for AT&T) or to HTC, since that would be a warranty repair.
I hope that this is just freak coincidence that both of you had this happen just now, and not a sign that we're all at risk of having the same issue eventually
How long have each of you had your phones?
EDIT: One more question for you guys...whatever is on the display on your screen rotates into landscape before the display shuts off right?
sirphunkee said:
It honestly sounds to me like both of you are dealing with a loose connection between the screen and the motherboard somewhere, either power or video feed, can't say for sure which. Unless you're willing to disassemble your rhodium (which isn't impossible, just complex), it sounds like it's time to send it to a service center (for AT&T) or to HTC, since that would be a warranty repair.
I hope that this is just freak coincidence that both of you had this happen just now, and not a sign that we're all at risk of having the same issue eventually
How long have each of you had your phones?
EDIT: One more question for you guys...whatever is on the display on your screen rotates into landscape before the display shuts off right?
Click to expand...
Click to collapse
i have own the phone for about three weeks...
though. bought it used from a friend who had it for four months.
but my friend bought it used from somebody too...
aka. not sure how long it has been used.
the display is rotated. and stays on as long as the right side is held.
before the 'tilt piece' is revealed. as soon as it is. the screen goes blank.
and i believe it would be the video feed...
i can still type with the keyboard. just can't see what i am typing.
unless i hold the screen from sliding completely out on the right.
and about the warranty...
would i have a warranty with htc still?
don't have proof of purchase.
just the phone and original box.
thanks.
My AT&T Tilt 2 has been exhibiting this behavior for some weeks now. It seems to be centered around the keyboard slide, but the behavior comes and goes. I found that slamming the phone on the desktop would bring it back to life for a little while, but then it would start to clap out again in a few days. What a pile.
Anyway, I have a fresh one from AT&T to swap out. Now all I have to do is get all my applications and stuff transferred over to the new phone before sending the craprod back to them.
sh4d0w86 said:
i have own the phone for about three weeks...
though. bought it used from a friend who had it for four months.
but my friend bought it used from somebody too...
aka. not sure how long it has been used.
and about the warranty...
would i have a warranty with htc still?
don't have proof of purchase.
just the phone and original box.
thanks.
Click to expand...
Click to collapse
Oh boy...yeah I didn't realize you'd gotten it third-hand. Well it has been less than a year since the Rhodium was released, so it's possible that HTC will still honor the 1-year manufacturer's warranty, but I can't guarantee it. My suggestion would be to just contact HTC America's service group (1-888-617-1113) and see what they say.
Best case: they agree to cover the repair
Worst case: an example of one of the risks you take when you buy something through "unofficial" channels
Yea luckily for me, I bought it second hand, but it was purchased from a retail store, meaning I got a warranty exchange. I just sent it back.
having same issue
im having same issue, when the phone is slid open, goes black, nothing gets it back on, the buttons light up, display dead
however, if i place it in stand by via power button in regular mode, then slide it open, it works, ive rattled and shook the phone, never goes back off, im typing this with it open and tilted....
any ideas?
prob leaving the htc community, samsung captivate, blackberry torch, or htc aria are my choices from at
I just bought my phone 4 days ago, and I'm having issues with the screen responsiveness. It just freezes up at times, sometimes it thinks one finger is touching it and does the whole zoom in/out thing when I touch it, randomly issues commands, touch buttons at the bottom don't respond, and only way it works for a lil again is to touch the power button to turn the screen off and back on. I have a link attached which shows the main problem area is when a lil pressure is put near the bottom, everything starts getting glitchy. It does this with all 3 ROMs I've used, which is another thing, I have to un root it so I can bring it to the sprint store. Since it's a brand new phone, and only 4 days old so far, do you think they will just replace it with another new model, or a refurb? I'd be extremely mad if it's a refurb since it's still in the 30 days. They also added TEP to my plan which I havent taken off yet. But since this is a hardware issue..
http://www.youtube.com/watch?v=I7-sNFfQhMY
The video doesn't even begin to show all the problems, but that's one I can replicate pretty well by holding it at the bottom.
Sometimes you get a bad phone HTC isn't perfect since you are within 30 sprint will switch it for a new one no charge.
Just go get a replacement
like others have said get a replacement simple and easy
CheesyNutz said:
like others have said get a replacement simple and easy
Click to expand...
Click to collapse
Eh, I'm on my third replacement, and gettng the last wasn't exactly "simple and easy ". Oh, and guess what needs to get replaced again due to another faulty display (interestingly this is the first phone I'm returning for the display... unless you count screen separation)?
Order a replacement, and when you get it, don't walk out of the store until you're sure the phone is working as it should.
Make sure they are not going to place an upgrade 20.00 fee on your bill.I had a bad screen as far as lifting up out of the frame from the bottom and light leaking out.When I went online a few days later to view my bill there was a upgrade fee and I had to call them but it was painless just had to give up about 5 minutes to get it done.
Just FYI
I'm really hoping when I go in tomorrow, they can return my phone and get a NEW one on the spot. I dont want them telling me they have to order it, etc, because I know they have a lot in stock. Do I just tell them I want a replacement because my screen is messing up when touching the rim of the screen? I really hope I dont get hassled. The phone is back to stock, S-ON, fully unrooted.
This video shows the issue even more. It's so bad today, I can barely use the phone
http://www.youtube.com/watch?v=qW5f1nHUmwY
I got my replacement today, brand new, hardware 0004. My first one was 0003. I am slightly disappointed because I can tell I have the "bad" screen version. It has a much more yellow tint to it than my first one. My rebate is also going to be declined now unfortunately, and it's going to be a hassle I can already tell.
Edit: I thought I have the worse screen, but it looks a lot better than the youtube comparison video I have seen. It also fades the different brightness settings rather than a solid quick change using power control. It still is a tad more yellow I think. I hope I can root this one just as easy as my last one.
I've noticed from day one that sometimes the proximity sensor seems to be a bit goofy on my phone. Sometimes the screen would go blank immediately after starting a call, and nothing I could do could bring it back except for putting it back up to my face and pulling it away again.
Welp, now the sensor seems to be totally dead unless I smack the phone with my hand. It makes calls, but the display goes blank and no buttons will work at all until the other person hangs up (doesn't matter if it's incoming or outgoing). I've only had the phone for a week. If I have it away from my face and smack the front of the phone with the palm of my hand the display comes back on and all buttons start working again for a few seconds, then it'll go blank again.
I've reverted it back to the stock DI18 that it came with and formatted the SD card (along with wiping everything more times than I can count). Anything else I should try before I take it back to Sprint tomorrow?
lifeofbean said:
I've noticed from day one that sometimes the proximity sensor seems to be a bit goofy on my phone. Sometimes the screen would go blank immediately after starting a call, and nothing I could do could bring it back except for putting it back up to my face and pulling it away again.
Welp, now the sensor seems to be totally dead unless I smack the phone with my hand. It makes calls, but the display goes blank and no buttons will work at all until the other person hangs up (doesn't matter if it's incoming or outgoing). I've only had the phone for a week. If I have it away from my face and smack the front of the phone with the palm of my hand the display comes back on and all buttons start working again for a few seconds, then it'll go blank again.
I've reverted it back to the stock DI18 that it came with and formatted the SD card (along with wiping everything more times than I can count). Anything else I should try before I take it back to Sprint tomorrow?
Click to expand...
Click to collapse
Mine is doing the same.... even worse actually. If the other side doesn't hang up (after taking call and it going blank)..... I have to do a battery pull to fix the issue until the next call. Other times (smaller percentage)... the screen won't turn off at all while talking on it. Either way is unacceptable. I don't know what is causing it... I tried to do a complete wipe and have stock rom.... but it didn't fix the problem. This only starting happening a few weeks ago. I took it into a sprint store and they ordered me a new phone (out of stock). It's still under warrantly... so all is good I hope. I plan on dumping Samsung once a better Gingerbread HTC phone comes out early next year. Samsung support sucks!
Mine goes blank on every single call - only way to get the phone to respond is by removing the battery or smacking the **** out of the front of it with my hand (at which point it brings up the normal in-call screen). Really annoying especially since I just got it on Tuesday.
Hopefully the store near me has some of them in stock. It's also a service center, and a fairly large corporate owned store, so I'm pretty sure I'll be able to swap it tomorrow.
So, the screen stays black until the call is ended right? Well, I have a solution for ending the call if the otherside doesnt hang up anyway, if your running 2.2...
You can set the power key to end calls, that way you can easily disconnect the call without having to have the screen on. I know this isnt a solution, but it may work as a stop gap until you can get it working correctly.
Menu->Settings->Accessibility-> (If a box pops up saying 'No accessibility applications found', just hit cancel) -> Check the box next to 'The power key ends calls'
If your not running 2.2, you can do this by editing one of the key map files, just follow the how to in this thread: http://forum.xda-developers.com/showthread.php?t=849075
That is an option, but it'd be a lot nicer if the phone actually worked the way it's supposed to.
Turns out the corporate owned stores are open late during the holidays, I swung by a little while ago and they confirmed the sensor was borked. Swapped it out on the spot.
Thanks though.
lifeofbean said:
That is an option, but it'd be a lot nicer if the phone actually worked the way it's supposed to.
Turns out the corporate owned stores are open late during the holidays, I swung by a little while ago and they confirmed the sensor was borked. Swapped it out on the spot.
Thanks though.
Click to expand...
Click to collapse
same here... they were out of stock though...and ordered me one. I wonder what caused the sensor to be broken?
this is not a sensor problem, i have this problem and only had it after having the "leaked" 2.2 froyo build, and flashing back to eclair.
this problem didnt happen on 2.2, but now it happens to me on 2.1
Same thing, when i make a call, screen is dead, the only way to get it back is to have the other person hang up.
I have the same issue. I make a call, put the phone to my ear and the screen goes blank. Say I'm calling my credit card company and need to enter in my credit card number via the keypad to continue, I take the phone from my ear back to horizontal in front of me and the screen won't turn on. I can press all buttons, open and shut the keyboard but nothing gets the screen to turn back on until the phone call is disconnected, or I pull the battery.
I don't have insurance through Sprint or Best Buy. I got the phone the first day it was available last fall. I flashed back to stock and still had the issue, the most I ever did was root and clockworkmod. What should I do? Do I have a manufactures warrenty? What kind of process is that, will I be stuck with a POS phone for a month like I was with my Touch Pro back when I had Best Buy replace that...
bmasephol said:
I don't have insurance through Sprint or Best Buy. I got the phone the first day it was available last fall. I flashed back to stock and still had the issue, the most I ever did was root and clockworkmod. What should I do? Do I have a manufactures warrenty? What kind of process is that, will I be stuck with a POS phone for a month like I was with my Touch Pro back when I had Best Buy replace that...
Click to expand...
Click to collapse
I think this would fall under the "manufactures warrenty" since you might have a possible hardware failure already within a year. I would call and ask to find out.
While I'm waiting to stop at the Sprint store after work I downloaded a few sensor test programs from the market. The ones that support the proximity sensor never give me a value when doing the tests. They usually just sit there in a status of "Waiting for sensor". Does anyone know how Sprint can test the sensor or will they just do what I've done?
bmasephol said:
While I'm waiting to stop at the Sprint store after work I downloaded a few sensor test programs from the market. The ones that support the proximity sensor never give me a value when doing the tests. They usually just sit there in a status of "Waiting for sensor". Does anyone know how Sprint can test the sensor or will they just do what I've done?
Click to expand...
Click to collapse
I know there are phone codes that will put you in the test hardware mode, I did this a while back when I got the epic. If I can remember as you come closer to the phone with the hand or whatever you use either the screen would turn off or it would vibrate maybe it did both like I said I can't remember.
I did some homework for you via Google of course, I tried it out and it worked, a screen will popup when you enter the codes pick sensors...just cover up the prox sensor and the value will change from 0 to a 1 and vibrate.
*#0*# - LCD TEST
red/green/blue/melody/vibration/dimming/megacam/Sensor/touch/sleepmode/LED/RECEIVER
Very useful tests for the LCD
I didn't know they had a hardware diagnostics built in. Thanks for the info. Looks like my proximity sensor doesn't change from 1.0 when I cover up the phone. I had a friend do similiar tests with his EVO and it switch from 1.0 to 0.0 when you got your finger about 0.25 inches away from the sensor. Thanks again.
Just to follow up, I took the phone to my local sprint store, which now is a repair center, and they took a look at it and said that they could fix it for $35. I don't have TEP on it so that is why I paid $35. I picked it up today and they put a new screen (top half of the slider) on to fix it and tightened up the looseness of the slider as well. Well worth the $35 in my mind. Although they forgot to put the micro usb cover back on so I have to stop back and see if that is laying around on the work bench.
I just got my Xperia play today and notice that I can hardly feel the button being pushed down (power button). Is this supposed to happen? First time it worked fine, but now it won't even work (e.g. to turn the screen on etc).
Should I give it a few days to see if it wears in, or return it? Thanks
Fully agree with you on this. I got mine yesterday and the button was sticking. There must be some sort of knack to put the battery cover on.
Would filing down the plastic be the answer? Seems a bit odd to resort to this when it should just work.
If it isn't working now to even turn the screen on, you should return it and get another, the sooner the better . Mine works fine, always some response from it.
Sent from my XPERIA PLAY 4G
I've got the same thing ; resorted to keeping the case around the power button slightly open - works fine like that.
Well what I meant was that it was so far stuck down that pressing it had no effect whatsoever. Even if I tried to use my fingernail to dig into the button, nothing happened. It returned to the normal state after pulling the back cover and put it back again, but after a bit of mashing the power button round, it got stuck and became useless again.
I was thinking of filing the back cover a bit, but I might as well return it instead.
I've just got mine unlocked (via Jinx13) so I'm loathed to return mine now. Let me know how the filing goes
Sent from my R800i using XDA App
This happened to mine too.
It resulted in the button acting like I was long pressing it when I was simply tapping it.
It seems the top of the button was getting stuck on the casing, I flicked it off the casing a few times and haven't any problems in a while.
But still, seems an issue.
I have a similar issue or had. I was able to wiggle it free gently.
Noticed it was the hard case protector I bought for it.... It's temporary for now until my skin comes then will go caseless.