Related
I tried to upgrade my rom but the process crashed. The utility mtty doesn't work because when I connect the universal, boatloader mode by the cable, to the pc, it says "USB not recognized" (sometimes when I connect the computer is frozen till I disconnect the cable of the universal)
Please, I tried to have some solutions in the forum but all the posts indicates is needed previously the usb connection.
Do you know if should be possible to run the flash of the rom in other way, for example using a serial cable connected into the miniusb of the universal, because the boatloader screen says "Serie, v.1.01"
I apprecite what you can say please, I'm really in a hole.
Try this...
Try taking out the battery for a few minutes (10-30mins) and reboot your PC then repeat upgrade process. Hope that helps. Good luck!!!
I have the same problem on my PC at work, it's caused by a poor USB chipset in the PC, or trying to connect through a USB hub.
The only thing I found that worked was to try a different PC, then it was fine...
sl9 said:
I have the same problem on my PC at work, it's caused by a poor USB chipset in the PC, or trying to connect through a USB hub.
The only thing I found that worked was to try a different PC, then it was fine...
Click to expand...
Click to collapse
In my case it still happening in other computers. Conclussion: some piece of the software in the universal has been lost. The screen shows "Serial" that means on some way that is opened to comunication but not USB.
My questions are:
- should be possible to put some starting software in SD and do the universal boot on it.
- do you know how to connect to the computer COM! port from the usb miniport of the Universal.
I appreciate, I was not planning to replace now the Universal...
beginner said:
sl9 said:
I have the same problem on my PC at work, it's caused by a poor USB chipset in the PC, or trying to connect through a USB hub.
Now works.... I still thinking windows is so stupid software made for distroy our mind ....
Solved after install drivers for a converter usb -rs232 ( I was looking for the way to connect from rs232 the universal)
I'm happy again and I promise don't try to change rom again (at least for a while)
If some person is interested in what brand of software/hardware I installed, send me a mail...
Thanks hearing me ...
Click to expand...
Click to collapse
Click to expand...
Click to collapse
i have the same problem with my friend's uni
does it mean that you don't have to own any adapter, just have to install drivers for USB to RS232 adapter
if yes, where to find it?
thanx
respectfully
ZeD
zedino said:
i have the same problem with my friend's uni
does it mean that you don't have to own any adapter, just have to install drivers for USB to RS232 adapter
if yes, where to find it?
thanx
respectfully
ZeD
Click to expand...
Click to collapse
I want to say that is running after doing some things and obviously some of it solved my problems. I made:
- unistall last version of activesync and go back to version 4.0
- delete all the applications using ports usb.
due the connection still not running (windows message: device not recognized) and because in the screen of universal I saw: "COMM1" I tried to connect from computer port rs232. By that I purchased some special cable, name: hama brand, rs232 serial, 9 pin - usb.
As you can imagine all the steps I followed were followed by the typical restart of windows. In this sense is important to say that the universal, after connect, need to do a soft reset each time (again windows....)
Other comment is that I unmark the option to connect by usb in activesync and mark the connection by com1.
and after all was done, connecting by usb the unniversal, kill wcescomm, windows said "NEw usb device, sync device". I started mtty and now appears the USB option, great! same time the screen in universal changed from comm1 to usb, more great....
and that's all.
does it mean you solve your problem using special USB 2 RS232 connector?
ZeD
PS: it was my first idea , but i still believe i can solve the problem using USB port
zedino said:
does it mean you solve your problem using special USB 2 RS232 connector?
ZeD
PS: it was my first idea , but i still believe i can solve the problem using USB port
Click to expand...
Click to collapse
I think my english wording was not fine. I mean I solved my problem after install the sofware -drivers- of the rs232 connector, but connecting to the universal by usb as on standard way I was syncronizing previous the crack with activesync.
OK, where to get this driver?
thanx
?????????? NOTHING ?????????????
zedino said:
OK, where to get this driver?
thanx
Click to expand...
Click to collapse
Try here.
http://www.hama.de/portal/type*3/action*1026/searchMode*1/q*039703
I have had the same problem several times now (search the forum for the thread).
I tried three different PC's/laptops and three different USB cables all with the same error as yourself.
Eventually I got a connection but the laborious process of trying - failing, restarting windows and soft resetting the phone, trying - failing........... until it finally worked. I did nothing differently the time that it worked but the strange thing is that it has worked every time since! Maybe the USB driver the phone has a bug in it that causes it to get 'stuck' in a mode where it will no longer correctly operate but once you have managed to 'kick' it into action it seems toi then carry on working.
It was also a ROM upgrade that caused my USB phone driver to stop functioning. Maybe the fact that the phone has a slightly diffferent software configuration after the upgrade but exactly the same hardware fingerprint causes the driver to fail.
Every time that I have had this problem it is after an upgrade but once I have gotten it to work once with the new ROM, it always continues to function - until the next upgrade.
shrubbery said:
I have had the same problem several times now (search the forum for the thread).
I tried three different PC's/laptops and three different USB cables all with the same error as yourself.
Eventually I got a connection but the laborious process of trying - failing, restarting windows and soft resetting the phone, trying - failing........... until it finally worked. I did nothing differently the time that it worked but the strange thing is that it has worked every time since! Maybe the USB driver the phone has a bug in it that causes it to get 'stuck' in a mode where it will no longer correctly operate but once you have managed to 'kick' it into action it seems toi then carry on working.
It was also a ROM upgrade that caused my USB phone driver to stop functioning. Maybe the fact that the phone has a slightly diffferent software configuration after the upgrade but exactly the same hardware fingerprint causes the driver to fail.
Every time that I have had this problem it is after an upgrade but once I have gotten it to work once with the new ROM, it always continues to function - until the next upgrade.
Click to expand...
Click to collapse
not works, probably is this device lost forever, i have restarted device and PC almost hundred times, still the same result, uni stuck in Bootloader screen top of page "Serial" bottom of page "v1.00"
nothing changed, even if i connect to USB port
if someone have some solution to this s*it pls let me know
thanx
i have had the same. my device wast recognized by my pc, bur i used maupgradeno_id and installed a other rom, even installed the original rom from qtek (latest) then after i was finished it started then i tried the other rom and it was working. ( pc did see a unknown device ) hope you have the same and its working also.
good luck
mrijnvis said:
i have had the same. my device wast recognized by my pc, bur i used maupgradeno_id and installed a other rom, even installed the original rom from qtek (latest) then after i was finished it started then i tried the other rom and it was working. ( pc did see a unknown device ) hope you have the same and its working also.
good luck
Click to expand...
Click to collapse
no, my problem persist, hundred times i tried to recover friends device using upgrade by original shipped ROM but the device is not recognized by system so there is allways connection error, so this kind of reliving this UNI is not usable
anyway, thanx for raply and suggestion
ZeD
mrijnvis said:
i have had the same. my device wast recognized by my pc, bur i used maupgradeno_id and installed a other rom, even installed the original rom from qtek (latest) then after i was finished it started then i tried the other rom and it was working. ( pc did see a unknown device ) hope you have the same and its working also.
good luck
Click to expand...
Click to collapse
If you're stuck in bootloader mode only, visit www.buzzdev.netand look for ExitBootloader utility written by the great Buzz. Just follow his instructions or scroll thru' Universal's forum here and there for problems relating to "stuck in bootloader"
hope this helps
no device is not recognized by PC so any trying to use exitbl is not available, anyway this option was one of the first what i have tried
thanx anyway
ZeD
i had the same problem with the QTEK of my principal after I upgraded his ROMs.
(after the hard reset, the pocket remained in bootloader mode).
you can solve this problem in a very simple way:
you have to launch the bootloader installation (BL1.01_RUU_UNI_V.1.2.EXE) from the PC (still connected with the PPC through USB) while the PPC is in bootloader mode (on your display you see "USB > Serial 1.01" or something like that).
then you do a SOFT reset and the pocket boot normally.
very simple.
i hope to be helpful to someone.
zedino said:
no device is not recognized by PC so any trying to use exitbl is not available, anyway this option was one of the first what i have tried
thanx anyway
ZeD
Click to expand...
Click to collapse
I had some problem. After uninstall all usb applications in the pc and install the software for cable usb -rs 232, doing some softreset in the pda connected, it turned the screen message "Com" by "Usb"
Hi all,
I was trying to upgrade my Qtek9000 with an official ROM Updater, but my device went immediately into the Serial bootloader mode and I've not been able to do nothing to run out from this mode...
I've tryied the solutions suggested in http://forum.xda-developers.com/showthread.php?t=290234 without any luck...
The problem is that neither Mtty nor the UNI_exitbootloader tool are able to connect to USB.
I'm using no usb hub, I'm running on a Dell Precision M90 notebook, I've disabled USB connection in Activesync (4.2.0) and also tryied with a pc without activesync installed.
Any idea?
Thanks
Paolo
Are you on XP or Vista, and what version of AS/WMDC do you have?
Hi,
I'm running Xp, ActveSync is 4.2.0, don't know what WMDC is sorry, can you please explain?
Don't worry about WMDC - it's only relevant if you have Vista.
Are you using the proper cable that came with the Universal? Some cables don't have all the pins wired. That (or a broken USB port) would explain why your Universal isn't going to USB mode when you plug in the USB cable. Have you looked carefully to see if it changes from saying "Serial" to "USB" at the top of the Bootloader screen when you plug in the cable?
If it does change to "USB", I would try upgrading to ActiveSync 4.5 - go to http://www.microsoft.com/windowsmobile/activesync/activesync45.mspx
Make sure you disable USB Connnections in the Connection settings before plugging in your Universal. Then try flashing the CE ROM again.
Good luck
BTW did you try doing a hard reset to get out of bootloader (both soft keys and then the reset button, then select 0).
Good advice, especially with upgrading to AS 4.5, it's a full release now on Microsoft Update site, and I have a feeling the WM6 ROMs may require it... Good luck with it, keep us posted.
Ok, thanks all!
This morning I connected the PDA to my office's PC with it's original cable and it instantly switched to USB mode...
So, I launched the upgrade and it's now in progress... let's hope!!!
It might really be a cable problem, yesterday night I tried with 2 different PC and a not original cable (I think it's my camera one...)
Thanks a lot, by now... I'll let you know own this story will end...
Ok, new ROM is up and running!
Thanks all!
Bye
Paolo
Good stuff.
I tried to upgrade my ipaq 3950 to wm2003 English version from wm2002 Chinese version and something went wrong so now I can only get into what I understand is called "parrot": Red background with Compaq in and Serial or USB when I connect w/ usb cable. It is v0.48. I've been trying to use mtty.exe to load a backup rom I downloaded off the net but every time I use the command lnb rom.bin it says "start download" then waits for a few minutes, then says "Fail to synchronize with the host". I know I should just buy a new pda but I don't have the cash. Any help would be appreciated.
Unbrick H3950
Well, here is what worked for me. Get the PDA in bootloader mode again ( that is the mode where the screen is red and says USB or Serial ). Connect to your computer via USB sync cable. Then you want to run the Ipaq Softpaq again to install your WM2003. It should start installing, leave it alone until it says that it is complete. Don't wiggle it or even touch it, because sometimes those Ipaq sync cable connectors get to the point where they will loose connection if moved.
My Qtek 9000 just don't wanna turn on. When on USB, my computer says "can not find USB device"! But, when I click "power button" + "light button" + "reset button", on Qtek screen is "USB" on the top of the screen and "v2. 01" on the bottom, and computer finds "USB device".. Still, I don't know what to do and how to turn my Qtek on. Please help me. I need my phone!
Thanks..
Milos
Perhaps a hard reset could help
If not try to reflash a ROM
Instructions here:
http://wiki.xda-developers.com/index.php?pagename=Uni_ROM_Upgrade
Good luck,
Look, I CAN NOT turn my device on. I'm holdind the "power button" but NOTHING!
P.S. I need boot loader v2.01. Can you find it for me please?
I think that I need the corect ROM that I had before "this situation".. Can someone find me a ROM v2.01? Or tell me what to do!?
You are in bootloader mode with USB showing on the top and bootloader version on the bottom. Just connect to your computer and flash another ROM.
The numbers on the bottom are NOT version of the ROM, but a bootloader, just try different ROMs or try shipped ROM for your device, or better still READ WIKI.
enigma1nz said:
You are in bootloader mode with USB showing on the top and bootloader version on the bottom. Just connect to your computer and flash another ROM.
The numbers on the bottom are NOT version of the ROM, but a bootloader, just try different ROMs or try shipped ROM for your device, or better still READ WIKI.
Click to expand...
Click to collapse
Hey Enigma your 500th post LOL ...
and EMO_Raver as you said when you connect your device to computer there is usb onthe top and v2.01 in bottom so it means you have G4 device and you can flash a uni rom G4 one....see instruction in first post by Orb3000...
I was trying to flashi it, but even my PC finds Qtek as new device, when I want to chose "USB" in "port" menu (in mtty), there is only com1, com2 and com3! There is NO "USB", so I cannot flash it!
And when I just click on the "new ROM" icon that I dowonloaded here I always get: ERROR 101 - CONNECTION ERROR
Pleace Check:
1. Your device is properly connected to the USB cable or cradle (of corse it is, my PC founds it as new device)
2. Your USB cable or cradle is properly connected on PC (same as in first, cable is 100% connected)
3. Your device is turned on (it's in booter mode, USB on top and v2.01 on bottom)
So, what is the problem. Someone told me that my softwere died, so I need to "feed" my Qtek with new software, new ROM. Is that a problem? How to do it? HOW TO START MY PHONE AGAIN?
I need help! Asap!
...
what OS do you have on your pc ? windows XP ?
If Vista or Windows Seven u must change driver of Microsoft USB Device ...
ANd be carefull of baterry .. if u will discharged battery u will have big rpoblem ...
FIXED! Thanks everyone!
Hi guys, sorry for my bad english.
Since today can't sinchronize my ppc with wm 5.0.
Here's the problem: when I pug it with usb cable, nothing happens.The orange light is on, the phone is in charge but nothing happens.Usually when I connect the phone I can see windows looking for ip address, and the activesynch shows... but this is not going to happening anymore.
I tried to reistall activesinch, I've cleaned the registry and i tried to connect it with others software.Still nothing.
Firewall is disabled.Any solutions?
Thank you in advance.
Zealot87 said:
Here's the problem: when I pug it with usb cable, nothing happens.The orange light is on, the phone is in charge but nothing happens.Usually when I connect the phone I can see windows looking for ip address, and the activesynch shows... but this is not going to happening anymore.
Click to expand...
Click to collapse
I had the same problem sometime ago. I've changed the wire first but nothing happened. My speaker, my Mic was dead and I could switch on FMRadio without the Hands-free!!!
What I did...??? I updated my mobile's Radio with 3.39.90 Version. How can you do this without active sync???
1. Remove SIM Card and Storage Card from the Mobile.
2. Press and Hold the Right Button (Recording Button) and Press together the Power Button. You will be in the Bootloader Screen. Try to update the Radio first.
3. Check it if it's working ok.
2nd way...
1. Copy the official ROM of WindowsMobile to the Storage Card.
2. Press Right Button (you know the Voice Rec) and holding that press the Power Button...
the mobile will be bootloader mode and will try to install the official ROM from the Storage Card...
wait a bit and then when it finish, check it if it is working properly!
Hope to help... waiting to "hear" sorry, to read good news
I have the same problem i cant sincronize the pda whith the activesync and i wish to change the rom. Now it's in france and i wish to change it to english, and it's locked to orange france i think. What can i make? It starts in bootloader, but the instalation from the card is not starting. thankx
le. and if i want to install something gives error 260
I had the same problem 1 month back, checked the mini usb data cable with a multimeter just to find that one of the data TX/RX wire was short with +5v wire, cable was faulty. the 1st and the last wires (+5v , -5v) were ok thats why it was charging the phone, but not connecting to pc, it was giving error unrecognised usb device.
u can also check for bent contacts at the USB mini connector on ur phone.
strange
hy guys
i´ve got a strange problem with my arte110.
for some reason i cant establish an activesync-connection,a few days ago i had some wm6.5 rom running and couldnt connect my device, then suddenly today (maybe because i reinstalled windows on my computer yesterday, i dont know) i was able to connect the phone while in bootloader... so i flashed happy and lucky the original wm (os 5.2.1620 build 18125.0.4.2) rom i got from t-mobile austria.
now its the same problem as before, i cant connect my device, i've restartet artemis and my computer several times, i've reinstalled activesync 4.5 a million times, i've tried all available usb-ports- different usb cables (same cable works with external harddrives) and even my office-computer, and so on...
my pda is (and was allways) charging but i cant syncronize.
has anyone any idea what could cause this problem?- please don't tell me the usb port of the pda is damaged, I wouldn't want to have to fix anything in this case...
hoping for good news, McPerfuntory
[by the way, please dont judge me for spelling mistakes, i'm from austria!!!]
done
okay guys, no need to respond anymore, i got it right..
but i don't really know how i repaired that one, i disassembled the devive cleaned everthing in there and cleaned the usb connector..
..works again