After I installed tomtom navigator I got the message that blue tooth could not start because there was no memory for it. So I did a reset, but the problem is still there. I wanted to do a factory restart and thats were thing got wrong.
Somehow the device starts loading and stops after a couple of seconds turning of the screen an gets non responsive. I have to take the battery out and it will try again but fails to load wm6.
I tried to do a factory reset again but it wakes up and starts loading wm6. I can boot into ps format but is will freeze after a few seconds E-boot is the same problem stays there for a few sec and then starts loading wm6.
I think its trying to load a corrupted firmware image and lockup. I can not find the correct wm6 image anymore the links are dead the upgrade to wm6 topic old.
Please help me get my HP HX2790b running again.
Kind regards
Sebastian.
voyager2 said:
I can not find the correct wm6 image anymore the links are dead the upgrade to wm6 topic old.
Click to expand...
Click to collapse
Just look 9 threads lower and there's my thread with hx2000 series wm6.5 - try it. [here]
Thats so cool, I thought it was a dead forgotten device, I will give it a try hope I still can get in the bootloader. Thank you!
Did the update, but stil no joy, formating PS after update it hangs, wil not load WM, sceen light go's out end of story.
Update it now boots, something the do with the battery cover being of?
Related
well i just downloaded and proceeded to flash the latest ROM from clubimate..
everything went normal, upgraded Radio, ExtROM, and CE ROM, then i was asked to unplug the device, and cold boot it, which i did.
after clearing the storage, the device reset, showed the splash screen, the version strings (latest ones) and stayed there.. i kept it for 15 minutes to no avail..
i reflashed again from the bootloader and still the same behaviour
Radio ROM takes 20 minutes to flash, EXT Rom takes less than a minute, then when CE flashing is done, i cold boot.. again it gets stuck on the boot splash screen
i tried a different PC, different cable, older ROM version.. all the same..
any clues as to what may have gone wrong here?
Thanks in advance
me too
Got the same problem and same description of proces
well,
i tried flashing the radio rom again, tried every mtty trick in the book and still got nothing.
eventually i've taken the phone to i-mate service center, and it's been there for a week
they said the motherboard is faulty and needs replacement, i'm suspecting the flash chip has gone bad.
now i'm not sure if this applies to all of us here with the same symptoms after the upgrade, but i really find it strange that after all these years with i-mate devices, upgrading, downgrading and flashing different roms, half the forum hits the same dead-end when a new update comes out from i-mate and they try to flash it on.
something is strange about the latest rom. i just wish i knew what it is
AntiProxy said:
...i'm suspecting the flash chip has gone bad...
Click to expand...
Click to collapse
you bet it is!
buzz
HELP PLEASE BUZZ
I have upgraded to rom JASJAR_WWE_13076_164_10900_wwe_ship
when rebooted I just get blank grey screen.
after messing about with mtty I got it so I can reinstall it again at last but then same problem.
Any I deas Buzz you da man
Cheer in advance
Jon
same problem here
damn, same problem with me
its not recognized by the pc and there is absolutely nothing on the screen
anyone found a solution for my thousand dollar paperweight?
AntiProxy said:
after clearing the storage, the device reset, showed the splash screen, the version strings (latest ones) and stayed there.. i kept it for 15 minutes to no avail..
Click to expand...
Click to collapse
I now have the same problem as well. I however received this through the trials and tribulations of getting my JJ into the damn bootloader...
Hi all,
Plz bear with my ignorance when it comes to upgrading ROMS etc.
Basically yesterday I upgraded to O2's official WM6 ROM .... and find it "not so good". It is slow to respond etc( i found it slower than my WM5 )
So now I wanna move to BB4, question is how do i do it??
I have downloaded an Artemis_USPL from Prof. So what are the steps I need to do??
Is it ...
1) Run start_uspl.exe from the zip file and let it complete.
2) Run( double click ) the img-46785-Tom_B_B_v4_0_TouchFlo_Professional.exe
Is that all I need to do?
Also, if I brick it .... what do i need to do to revert to an original ( say o2 WM6 ROM) ... is it USPL it again then run the O2 rom??
Many thanks
Fahd
yep, thats what you need to do. both 1) and 2) will need some user input and after it's done the device resets itself. so after 1) wait until restart is complete, then do 2).
for your original roms you dont need uspl. but if you are not completely sure, run it anyway.
Thanks for that. Time to give it a whirl! Wish me luck!!
Hmmm doesnt wanna play ball.
Did the above and ran uspl .... got stuck on a white screen. So I rebooted the Orbit and tried running the BB4 .exe ... got to 3 % and told to that .......
Error 270: Update Error. The image file is corrupted. Please check your update ultilty.
Can anyone help?? It will not upgrade ROM.
I keep getting the white screen and it cant run ROM utility(Error 224: Device not responding ).
I then reset the device and run BB4 ... I get to 3% and then I get error:270 ( image file is corrupt ). I have downloaded the ROM again and still get this error.
Any helpers out there??
Thanx
Fahd
I had the ame problem mate. What you need to do is revert back to the original 02 WM5 Rom which can be found on this forum somewhere. Then once installed, run uspl & then the BB4 Rom & hey presto your sorted.
For some reason i couldnt get uspl to work on WM6 02 rom either
Hi fadhp,
Ensure that your windows firewall is disabled and also you shut down any anti-virus programs running on your PC
I also found that turning off all the plugins on the today screen helped me to upgrade my O2 orbit.
I went through the same issues as you with corrupted images at 2% , however following the steps above helped me.
The firewall was disabled and so was AV ... so not sure about next steps.
I thibnk I shall try downgradind to original O2 WM5 rom and then upgrade ....
question is where in this forum is that Rom!! I had seen it before but as usual when u dnt need something you find it and when you need it u cant!
Will keep on searching .... anyone know the link plz save me some time!
Thanx
F
question is where in this forum is that Rom!!
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=314866&page=2&highlight=orbito2uk-wm5
The link for the original O2 WM5 is in post #13, the 3rd one down.
Thanks for that.
Downgraded to WM5 now .... and tried to run BB4 .... still no joy. Same error.
Maybe i'll try another ROM just to see if that works and if it doesnt then MUST be my PC or something.
Here goes!
Cheers guys will kepp u posted.
F
Tried another machine ..... XP SP2 not FW or AV still failed.
Always get to 3% then crash.
HELP!!
Tried BB3.7 still no luck. 3% and crashes .... on 2 diff PC's.
I noticed that USPL runs ver 3.0.3.0 of the update utility but the actual ROMS when you launch them are running 3.6.3.6 ... does this make a difference?
Help guys plz!
Those are the issue no's of the rom upgrade utilities - it does not matter. It appears you are still not cid unlocked. whats your spl no? take it from first bootscreen.
SPL is 1.25.0000
IPL is 1.25.0001
Ideas??
The spl from uspl is 1.110000 so you need to run uspl again. Even if the screen goes blank wait till it says your rom has been upgraded.
Thing is when i run USPL and it gets to 100%, all i get is a white blank screen and nothing happens. So i have to reset the device.
Then i try and run the BB4 etc install and get to 3% before it conks out.
When I get the white screen ... what else can i do??
Some people had to run uspl 3 times in a row for it to work. Did you wait a while on white screen before giving up? I guess you are on 02 wm5 at the moment if not flash to that and try again. If you are do a hard reset and try again - few times in a row.
OK looks like USPL doesnt work for me!
Everytime I ran it under WM5 i still had 1.25.0000 and then i upgraded ROM to O2 WM6 and now everytime I run USPL it stays at 3.04.0000.
It doesnt do anything after the white screen ..... just sits there like a duck!
With so many ppl having succesfully done this surely someone can be a Wizard of Orbit??
fahdp said:
Thing is when i run USPL and it gets to 100%, all i get is a white blank screen and nothing happens. So i have to reset the device.
Then i try and run the BB4 etc install and get to 3% before it conks out.
When I get the white screen ... what else can i do??
Click to expand...
Click to collapse
Had same problem. Dont reset the phone but just if you see only the black screen, run the USPL update.
I have an orbit and uspl flashed first time from wm5 and wm6 - is yours usa orbit? If you really cant run uspl then it will need cid unlock from imei check - it costs but you have permenant cid unlock so you need not worry again.
Hi! I have recently flashed my hp ipaq hx2410 to wm2005, the update process went fine but the device doesn't boot anymore. It shows the loading bar and it gets stuck when it fills up. I have tried hard reseting it but the problem persists. I can't flash it because active sync doesn't "see" it anymore... just a local area connection X - limited or no conectivity. What can I do ? Is there a way to boot the device in some sort of flash mode or something? Thank you very much
I had to do hard reset about 3 times when upgrading my hx2490B.
f1xxx3r said:
Hi! I have recently flashed my hp ipaq hx2410 to wm2005, the update process went fine but the device doesn't boot anymore. It shows the loading bar and it gets stuck when it fills up. I have tried hard reseting it but the problem persists. I can't flash it because active sync doesn't "see" it anymore... just a local area connection X - limited or no conectivity. What can I do ? Is there a way to boot the device in some sort of flash mode or something? Thank you very much
Click to expand...
Click to collapse
I have done a lot of hard resets but the device still gets stuck.
Another thing... I did not hard reset the device before de WM05 rom update. I thought it should do that by itself.
And second... If I get it to work I want to flash it to WM06. I have the rom but are there some special steps to be followed for this update ?
My pda still gets stuck in the bootloader and then the backlight turns off. Should I leave it that way untill the battery is completely flat ?
Some people say that removing the battery for 24 hours may help.
Try that.
When i flashed my 2490 i did format the device and than did the flash.
But I don't think that matters cause the first time when i did flash i didn't format the drive and it was OK.
f1xxx3r said:
I have done a lot of hard resets but the device still gets stuck.
Another thing... I did not hard reset the device before de WM05 rom update. I thought it should do that by itself.
And second... If I get it to work I want to flash it to WM06. I have the rom but are there some special steps to be followed for this update ?
My pda still gets stuck in the bootloader and then the backlight turns off. Should I leave it that way untill the battery is completely flat ?
Click to expand...
Click to collapse
I'll remove the battery then and see tommorow. The main question is: is my device completely dead or is it "resurectable" ? I don't think that it need servicing .... but ... just asking
Thank you for the replies. If the batterry removal fix works I'll post here. In the meantime any other possible sollutions are welcome.
My pda still doesn't boot. I have removed the battery for 24 hours and nothing. I have drained the battery and nothing. Did numerous hard resets and still no result. Can anyone help me ?
Just an idea (since I had to do this yesterday) maybe try formatting the device.
After flashing 4PDA ROM to my device it would get stack on the same screen as yours. After formatting it all went OK and I had WM6.
For my device I had to click calender + power + messaging + reset, release reset - release all.
f1xxx3r said:
My pda still doesn't boot. I have removed the battery for 24 hours and nothing. I have drained the battery and nothing. Did numerous hard resets and still no result. Can anyone help me ?
Click to expand...
Click to collapse
It's still dead....
It's back. P.S. Format did the trick
Same problem
i have " HP IPAQ hx2410 " with WM2003 CE 1.10.0 and i upgraded with this window 5.2 it upgraded successfully but i m stuck on the first loading screen. its stuck when loading complete i have tried every thing such as boot-loader thing and also cant downgrade it . . . so kindly plzzz any one tell me how can i go to my initial state on wm2003 ASAP.
WHAT IS P.S. Format ??? and how can i do that . . .
The answer is here:
http://tinyurl.com/2d4cza7
Hey guys, I've updated to wm6 and sometimes after my p3300 started to either black out or get into a irresponsive mode where the screen is just lightly on. No buttons replies! Once its happens the only solution is to do a soft reset and then pass to phase 2, try to restart it. That bad boy gets stuck directly at the loading process and its maybe - with luck- that it will go through the os loading after 10 tries and soft resets. The phone can work then from five minutes to ten hours and will get stuck again. What is Happening???!!! Also I don't think its the battery cause it does the same thing even with full battery. Last detail, I just passed the warranty limit and its too late to send it back. What can I do??
Did you updated with the official Rom?
Try to flash it again.
Or just try it out a cooked WM6.1 ROM. I recomend Artemis touch Vanilla 4.02.
Cheers
You tried a hard-reset?
babar_almighty said:
Hey guys, I've updated to wm6 and sometimes after my p3300 started to either black out or get into a irresponsive mode where the screen is just lightly on. No buttons replies! Once its happens the only solution is to do a soft reset and then pass to phase 2, try to restart it. That bad boy gets stuck directly at the loading process and its maybe - with luck- that it will go through the os loading after 10 tries and soft resets. The phone can work then from five minutes to ten hours and will get stuck again. What is Happening???!!! Also I don't think its the battery cause it does the same thing even with full battery. Last detail, I just passed the warranty limit and its too late to send it back. What can I do??
Click to expand...
Click to collapse
did u run a uspl first?
jahrami said:
did u run a uspl first?
Click to expand...
Click to collapse
If he upgraded it, then he didn't need it or it was the original WM6 ROM.
The problem was after upgrade!
Flash it again or do a hard reset!
Cheers
Thanks for the help. Yeah I installed the touch Vanilla 4.02 cooked WM6.1 ROM. And I believe the uspl was in the file. As far as I remember I ran it but had no feedback whether it worked or no...
Would a hard reset get the bad boy back to wm5 or reboot with wm6.1?
I *should* reset/default to factory settings for whatever ROM was last successfully flashed to the device. You will lose any installed programs/data so so a PIM backup/ActiveSync before hand if required.
hey, I'm only 1.40 Olinex unsigned;
when i first boot up I have this:
R 52.2.25.12h
G 1.00.25.05
D 1.93.0.0.0
My phone shuts down by itself, after i see the HTC logo and i hear the shut down sound.
why is that happening, is it software or hardware?
PS: RUU_Diamond_HTC_Europe_1.93.401.2_Radio_Signed_Diamond_52.29.25.12_1.00.25.05_Ship
I am flashing with this ROM, and with some other ROMs it is not even booting up
try this mate
try running mtty then reflash your rom, mtty formats your nand chip and repairs any erroes read THE DEFFINATIVE MTTY THREAD all explained there got to be worth a try hope this helps
trying this now will report on results thank you mate
still having problems, now phone wont boot up at all
i think i can make it boot
(I got USB error after i pressed <- and Vol Down to flash ROM )
is there a problem in my SPL? is my phone bricked?
i can boot into WinMo after i have left the phone for a few hours
but now 5-20 minutes after booting (depending on each time), suddenly i see the HTC logo, and here the shut down beep
any help ?
could it be a bad battery issue?
because when i turn it on i see an exclamation mark next to the battery icon in the bar on top
any suggestions? plzplzplz !!
MTTY Thread
Reflash your phone doing EXACTLY what it says in that thread and you should be good to go.
mzaouar said:
could it be a bad battery issue?
because when i turn it on i see an exclamation mark next to the battery icon in the bar on top
any suggestions? plzplzplz !!
Click to expand...
Click to collapse
Buy another battery, It looks like battery problem.
Good luck
now the battery looks like it's working fine, i've flashed a new radio ROM, but it's getting turned off again :S
should i upgrade to the 1.93 HSPL? because i have a 1.93 ROM
can the problem be from the radio?
Same thing here,
Been flashing the diamond to the bone.
After flashing the (22 jul) verion of the NRG warhawk rom
I have been experiencing some glitches.
As it was my first step from wm 6.1 to 6.5 and I dont want to go back.
The errors ive experienced are not related to rom issues.
Because i got em almost with every rom.
- random restarts
- loss of contacts
- no responding of the device
And ive been reading about the MTTY sollution I go and try that one.
Enonoid, so you didnt find a soltuion to your problem?
and if not, what do you suspect the culprit is?
Been flashing the diamond to the bone.
After flashing the (22 jul) verion of the NRG warhawk rom
I have been experiencing some glitches.
As it was my first step from wm 6.1 to 6.5 and I dont want to go back.
The errors ive experienced are not related to rom issues.
Because i got em almost with every rom.
- random restarts
- loss of contacts
- no responding of the device
And ive been reading about the MTTY sollution I go and try that one.
Reply With Quote
the problem isn't rom related running MTTY formats the chip where the rom resides its like reloading windows on your computer when you know there are bad sectors on your hard drive. it just wont happen follow the THE DEFINATIVE MTTY THREAD and honestly all should be fine it sounds quite tricky at first, but I use mtty everytime i reflash now saves whishing you'd done it once you've reinstalled everything and believe me its so easy if you just follow the guide.