Please please help me!! - Touch Diamond, MDA Compact IV ROM Development

so, i don't know where i went wrong with trying to get wm6.5 on my diam500, but now all it will do is turn on, go to the screen that says touch diamond then it turns off.
or if i hold down the volume down+the power button it goes to the .. boot loader?(i believe thats what its called)
can someone please help me. or tell me what to do from this point to fix it so i can at least use my phone again.

Did you Hard Spl before flashing the cooked ROM?
Press and hold Volume Down + "OK" (the round botton) and meanwhile press and hold the soft reset bottom to enter the Hard Rest menu then press Vol up to Hard reset the mobile.

well, the latest hapdSPL's werent workingon my phone, so i had to use tha HardSPL 1.24.
the bootloader screen shows:
security unlocked
diam500
spl-0.57.CMONEX
MicroP-Diam (led) vB
PSOC-DIAM STAGE_EVT V20
and it will only go to that when i press the voldown + power key, otherwise it just continuously turns on then off.
i really hope its not fried

1- Try the original ROM: Go to bootloader, connect phone to pc by USB and install Original ROM
2- Try MTTY (described in this forum)

Related

Bricked Diamond

Hi folks,
Can anyone help me?
I was using BSB 6.5L WM6.5 on my Diamond and i had some problems with that.
Mainly, my Diamond was "hard reseting" the manufactures settings everytime i turned it on.
So i decided to downgrade it to WM 6.1
At this point i started to have serious issues.
I installed Rom 1.93xx and just after the uptade, my Diamond froze in the first black screen (Touch Diamond and radio/Rom version).
Even if i do the hard reset, it freezes again in the boot screen.?
So, how could i go back to the Rom i was using before or install another one?
My Diamond is useless now... Hope someone can help me.
Thanks
should've used search, this is also a wrong forum for this topic.
with that said, power off the phone, press and hold power, volume down and reset until you see the tri-colour bootloader screen, connect the phone to your PC, you should be able to flash at this point.
do report back.
Japex said:
Hi folks,
Can anyone help me?
I was using BSB 6.5L WM6.5 on my Diamond and i had some problems with that.
Mainly, my Diamond was "hard reseting" the manufactures settings everytime i turned it on.
So i decided to downgrade it to WM 6.1
At this point i started to have serious issues.
I installed Rom 1.93xx and just after the uptade, my Diamond froze in the first black screen (Touch Diamond and radio/Rom version).
Even if i do the hard reset, it freezes again in the boot screen.?
So, how could i go back to the Rom i was using before or install another one?
My Diamond is useless now... Hope someone can help me.
Thanks
Click to expand...
Click to collapse
What technote said is incorrect, doing that will just cause it to try and read from the Internal Storage, what you want to do is what I did when I had the exact same problem;
With the phone on the frozen screen - make sure the USB cable is DISconnected, open ActiveSync/WMDC on the PC and in connection settings, disable USB connections. Now press the red reset button on the phone and as the phone is turning on (before it vibrates - 'touch Diamond' splash), you need to press Volume Down once, don't hold it. Just press it once. Now plug the USB cable in when the tri color screen appears, and Serial should be written near the bottom. Renable USB connections in ActiveSync/WMDC and then flash a ROM. All should work.
Thanks...
It worked flawlessly....
incredulous said:
What technote said is incorrect, doing that will just cause it to try and read from the Internal Storage, what you want to do is what I did when I had the exact same problem;
With the phone on the frozen screen - make sure the USB cable is DISconnected, open ActiveSync/WMDC on the PC and in connection settings, disable USB connections. Now press the red reset button on the phone and as the phone is turning on (before it vibrates - 'touch Diamond' splash), you need to press Volume Down once, don't hold it. Just press it once. Now plug the USB cable in when the tri color screen appears, and Serial should be written near the bottom. Renable USB connections in ActiveSync/WMDC and then flash a ROM. All should work.
Click to expand...
Click to collapse
When i do this, it still keeps going to the splash. I reset, press vol down, and it continues to go to the splash. If i do it the other mentioned way, power, reset, vol down i get to the tri colour screen.
how to enter in bootloader = press volume down and reset simultaneous !
link

Phone Stuck On SPL and IPL mode

Hi all,
I have a HTC P3300 phone, it was freezing, soi decided to do a hard reset, by pressing the two button and the pwr button - i get the screen where i can see the screen stating that the Phone wil be reset to the manufactures default, and whn i press the send button - there is an error " format Failed" and then the phone boots and i see a gree bar'd line with the :SPL" and the "IPL" numbers displayed on the screen , and then the phone switches off , the phone when plugged into a pwr socket has the charging light "orange" that comes on/off at intervals, i have tried to flash the phone using the flash utility but no luck, i have also tried to press the Rest button with the camera button "still no luck"
- I have tried to replace the phones battery - still nogo,
cold sme one help me on this in a step by step procedure ( and the links if i have to download any file)

I can't access my orbit's bootloader

I've try all the way to get my ppc in the bootloader mode but it seems doesn't work(Record+SR,....)
any body can tell me why it is?
thks
does hard-reset menu work?
if so, try to hold both Rec + Power at once and softreset, don't release the keys until you see the tricolor screen

Ran task 29, now phone is stuck on bootscreen HELP!!!!!

I ran task 29, and after its done all my phone does is stay at the olds roms startup splash screen!!!! What do i do??? Is it bricked??? Why would someone tell me to do that if it was gonna break my devise??? can someone please help
alroco20 said:
I ran task 29, and after its done all my phone does is stay at the olds roms startup splash screen!!!! What do i do??? Is it bricked??? Why would someone tell me to do that if it was gonna break my devise??? can someone please help
Click to expand...
Click to collapse
lmfao relax. Hold your volume button down, hold the end key down(the button you hang up the phone with) then push the power button.
When your phone boot you should see a gray screen that say serial, plug your device into the computer and serial should change into usb. Then run the rom and there u go
BeEazy10 said:
lmfao relax. Hold your volume button down, hold the end key down(the button you hang up the phone with) then push the power button.
When your phone boot you should see a gray screen that say serial, plug your device into the computer and serial should change into usb. Then run the rom and there u go
Click to expand...
Click to collapse
Doesn't that trigger Ramdump mode (well, I don't know what that means, actually)?
All the OP needs is to go to Bootloader Mode to flash a ROM via USB. Bootloader is easily accessed by: Turn off phone, then press/hold Volume Down + Power button.
thanks guys, ive been using android, and never a minmo device, thanks everyone!!
sumflipnol said:
Doesn't that trigger Ramdump mode (well, I don't know what that means, actually)?
All the OP needs is to go to Bootloader Mode to flash a ROM via USB. Bootloader is easily accessed by: Turn off phone, then press/hold Volume Down + Power button.
Click to expand...
Click to collapse
Yes that mode what ever its called
If you read the sticky posting on Task29, you would see it tells you that this is normal behavious for Task29, and it also tells you how to get out of it
steviewevie said:
If you read the sticky posting on Task29, you would see it tells you that this is normal behavious for Task29, and it also tells you how to get out of it
Click to expand...
Click to collapse
Sortof. I just tried task29 for the first time a few days ago. I freaked out when I got in the same situation as him, but then read through the thread. There's the option of shutting the phone off, and pressing vol down + power key. I ended up doing vol down + power key + push reset with stylus at the startup screen. Simplest solution for me.
taking off the battery, istnt that simplest?
Amd here is the theme about this
raz1337 said:
Sortof. I just tried task29 for the first time a few days ago. I freaked out when I got in the same situation as him, but then read through the thread. There's the option of shutting the phone off, and pressing vol down + power key. I ended up doing vol down + power key + push reset with stylus at the startup screen. Simplest solution for me.
Click to expand...
Click to collapse
In the very first posting of the Task29 thread, it says :
When phone boots to "Touch Pro 2" screen (or whatever your splash screen happens to be), I hold down the volume down button while hitting the reset button.
Click to expand...
Click to collapse
IMO, the smartest thing to do is when Task29 is near 100% (I think it pauses at around 96%), hold down the Volume Down button. That way, when the phone (tries to) reboots, it goes straight to Bootloader.
thanks all you have been more than helpful, ive been using this site for a while (for my android device) but just recently made an account. All of you keep on getting it done!!!
Moved as not ROM Development.
BeEazy10 said:
lmfao relax. Hold your volume button down, hold the end key down(the button you hang up the phone with) then push the power button.
When your phone boot you should see a gray screen that say serial, plug your device into the computer and serial should change into usb. Then run the rom and there u go
Click to expand...
Click to collapse
Hey, I have a Touch Pro2 and I tried the key combination above and it didn't work for me. I did get it to work however using the send key (green button) instead of the end key....
I.e, held volume down button, held send key and pressed power key once... ;-)
Phone MUST be off before doing the key combo...

[Q] How to reset OS??

I was facing some problems with my touch diamond from past few days. So I have installed new ROM 6.5, it was working properly but after next day I found OS is hanged so I restarted windows. But then it is stopped at the beginning only, it cannot able to boot completely. So I have tried hard reset (vol down + action + reset) but it also doesn't work. So I can't able to connect it to laptop through activesync.
Any body have solution on this to reset OS??
Please tell me...
X
Reinstall ROM from Internal storage
Press Vol Down + Back button (Bottom right) + Reset
Keep hold of First two buttons, and only press reset once, keep hold of first two buttons until coloured bootloader screen appears, follow instructions
Hard Reset
Press Vol Down + Middle Circle button + Reset
Keep hold of First two buttons, and only press reset once, keep hold of first two buttons until coloured bootloader screen appears, follow instructions
Re
I have tried Vol Down + Back button (Bottom right) + Reset
but it was showing the screen showing message like 'Trigger USB host...' and after some time it was showing 'Retry Enter USB'
After that I supposed to press vol down + action(circle button) for some time until coloured boot loader screen appears, to enable USB connection. After that I could reinstall the system.
Thanks for the help.
X
SO it is all working now ?

Categories

Resources