Hi All,
My diamond screen suddenly stopped responding. The screen calibration is also not working. I tried a hard reset and after that, it stopped at the screen 'Tap the screen to setup your windows phone'. I am not even able to do that. Any help is appreciable. Thanks in advance.
jitheshg said:
Hi All,
My diamond screen suddenly stopped responding. The screen calibration is also not working. I tried a hard reset and after that, it stopped at the screen 'Tap the screen to setup your windows phone'. I am not even able to do that. Any help is appreciable. Thanks in advance.
Click to expand...
Click to collapse
Try re-flashing a rom, or maybe your touch screen (digitizer) needs replacing, if you do this yourself i would recommend buying the digitizer and lcd together as one, it will make a whole lot easier trust me lol. The lcd screen is easy to break.
Had this problem, too, but since I couldn't get back to stock SPL at that time I put my Diamond into a shelf for about 2 days.
When I then tried to get back to stock SPL the screen suddenly responded again.
So, try to take off the battery for a long time (more than a day) and hope it recovers.
Didn't have the problem again.
Change the Touch Screen
jitheshg said:
Hi All,
My diamond screen suddenly stopped responding. The screen calibration is also not working. I tried a hard reset and after that, it stopped at the screen 'Tap the screen to setup your windows phone'. I am not even able to do that. Any help is appreciable. Thanks in advance.
Click to expand...
Click to collapse
I had a similar problem solved with changing the touch screen since the phone was under warranty I have to revert to the stock SPL and stock ROM before I gave it for service. If your phone is not under warranty you can buy the touch screen from ebay.com with a manual and all required instruments for replacing the same.
This happened to me because I was talking to someone over an hour in a humid place which caused sweat to get into the phone through the speakers.
Regards,
V.Balaji
Solution
Okay, I've just had this problem with an HTC Touch, and I think this works with any HTC that has a "digitizer" rather than an all-in-one touchscreen (I think newer phones have digitisers).
I'm not sure if this will always work, but I've just done it - sometimes the inactive touch screen is "broken" because the layers are stuck together (so the phone can't tell where the touch is, hence unresponsive). With mine, I looked at the screen side on and could see a kind of "oily" patch in the light.
The solution is to get masking/gaffa tape - the very sticky brown one. Stick it down on the screen/digitizer and then keep pulling it off - this pulls the layers from each other. I kept repeating this lots before it worked - and in the end I pulled the top layer completely off (I think you should pull from the top of the phone, as the layers need to be attached at the bottom of the screen/digitizer). Once it pulled away, I gently lay it back down (after panicking!!) and hey presto it started working again.
Good luck!
salterlee said:
Okay, I've just had this problem with an HTC Touch, and I think this works with any HTC that has a "digitizer" rather than an all-in-one touchscreen (I think newer phones have digitisers).
I'm not sure if this will always work, but I've just done it - sometimes the inactive touch screen is "broken" because the layers are stuck together (so the phone can't tell where the touch is, hence unresponsive). With mine, I looked at the screen side on and could see a kind of "oily" patch in the light.
The solution is to get masking/gaffa tape - the very sticky brown one. Stick it down on the screen/digitizer and then keep pulling it off - this pulls the layers from each other. I kept repeating this lots before it worked - and in the end I pulled the top layer completely off (I think you should pull from the top of the phone, as the layers need to be attached at the bottom of the screen/digitizer). Once it pulled away, I gently lay it back down (after panicking!!) and hey presto it started working again.
Good luck!
Click to expand...
Click to collapse
Thanks alot the method really worked , i really owe you dude thanks again
Putting the phone in the fridge makes screen work!
I know this is an old thread but why does putting the phone in the fridge for a few minutes make the touch screen work? Even if I put it out of a moving car and it cools down, then it works for a bit.
Anyone know why this is and how I can fix the phone permanently?
Related
Hi,
I have a problem with XDA - it is stuck at the align screen and keeps looping the cross over the screen forever.
I have reflashed rom a few time, I have disassambled the phone - cleaned the contacts, cleaned the screen, removed the schotch from the lcd 4 connectors. I even tried to glue a big piece of schotch to the screen pull the touchscreen of the lcd a bit...
nothing helps so far!!!
Do I need a new touchscreen? I really would like to fix this one, because it shouldn't be broken - it looks so nice and clean!?!!!!
Please help me!!
I found that pressure applied to the bottom left corner of the touchscreen behind the today screen button will cure touchscreen problems. When dissasembled it would be the area where the 4 leads branch off the touchscreen. I tested by slipping a doubled over piece of paper under that left corner (with the unit fully assembled). It put just enough pressure on that area that the touchscreen started working again! Try it, might work.
Thanks, but nope - stucking a paper under the casing didn't help.
I have managed to get pass align screen by deleting welcome file on PocketPC/windows/startup, but still the screen is faulty as the bottom and the top part of the screen doesn't respond to stylus!
What could this mean? Is there something wrong with the robon cable? Could reattaching the ribon cable help?!
Guess what! Just fixed the touchscreen - everybody said it's impossible - I don't know how I did it - just removed the ribon cable and soldered it back - it worked for me!!
Thanks all!!
XDA iis digitizer replacement and align screen solved
Ok to start with it is nearly impossible to solder the ribbon from a new digitizer on to a ppc lcd. I screwed up a screen trying to do that with a so called fine soldering iron but this is micro soldering, looks to be only possible by a machine. Dont glue it either as i've heard its bad too but if some one has had success then post and let us know. I just sticky taped it to the 4 metal connection lines. The ribbon is slightly see through and can easily line up.
Now when I had done this the screen align kept cycling. Yes even up to 20 times would not fix it but if you go back to the ribbon connection and make sure it is exactly on mark then you'll know the connection is ok. If the align screen responds to your taps well then it is just either the ppc getting used to the new digitizer or what I found was shuffling around the screws and making sure the insides of the ppc were snug and nothing pressing too hard on the lcd. The comment on placing a piece of cardboard was a good sujestion as when I screwed the whole thing together it suddenly aligned.
When the ppc finished installing, the alignment was a bit off by half a centimeter so i ran the align screen utility from settings again and it aligned! Now it works. Fingers crossed.
No response from a seemingly perfect touchscreen.
Hello guys it seems you guys have mastered correcting touch screen problems. If you would take a moment of time out of your day to help a dumb college kid. I have a SX66 and it has worked perfect and has remained to be a cool phone thanks to this site and the developers. I have retraced my steps a million times and here is what happened. I was surfin the web on my phone at school and the battery dropped off. I put the battery back on but the phone would not power up. 30 minutes later I tried my backup battery and bingo it powered on. But the touchscreen does not work at all. I took the phone apart and made sure connections were good and all was good. And as a last resort I reflashed my copy of wm6 to the phone. There is no cracks or blemishes on the screen. Any ideas will be greatly appreciated
My Hermes 8525 display has gone fully white.. I cant see or do anything on it.. Anyone got any idea why this is so ??
8525,
Dutty's Premium Windows Mobile 6
try searching...
typed in " white screen hermes" and came up with a heap of links... heres 1 : http://forum.xda-developers.com/showthread.php?p=2254487
Did the display fade to white? Or did you turn your screen back on and find it was all white?
There's a known problem for HTC Hermes with the D-pas causing white screen, and a little mod to fix it by putting something behind the D-Pad itself such as a small very thin piece of foam. Obviously this requires taking your mobile apart.
If you flashed and then got a white screen I'd try getting into your bootloader and take it from there....
2 solutions
Hi,
had the same problem. I took the battery out (read this in one post somewhere here) and then everything went ok. I also saw the post about the dpad, but was not nessesary. Although I think I was just lucky. I think that it happens often, you should do that.
Regards,
They display faded into White.. It was working fine. one fine day, as i was replying to a text message.. or when searching phone book.. or any action.. slowly the entire screen faded into white.. once i did a restart and removed the battery a cpl of times and it seemed ok.. but now its permanently white.. i cant even enter boot logger mode.. or even if i did, i wont know or cant see that i am in bootlogger mode...
Any ideas??
southeastblue said:
Did the display fade to white? Or did you turn your screen back on and find it was all white?
There's a known problem for HTC Hermes with the D-pas causing white screen, and a little mod to fix it by putting something behind the D-Pad itself such as a small very thin piece of foam. Obviously this requires taking your mobile apart.
If you flashed and then got a white screen I'd try getting into your bootloader and take it from there....
Click to expand...
Click to collapse
1st, scuse please 1st post, bad day at work...
1. Does it get hot anywhere on the front of the hermes. A mate of mine had a capacitor burn out that caused white screen...
2. Try opening the keypad then reseting. This worked for mine BUT it is a pressure issue and as I closed it found that touching a certain spot in the bottom right corner of the casing would make it whitescreen again.
Other than that you might have to open up your hermes to try and fix...
Heres how to open up :http://michael-channon.spaces.live.com/PersonalSpace.aspx?_c02_owner=1
Make sure you have the correct tools though as it makes life easier. No. 6 torque key and a flat bladed screwdriver are good..
Cheers...
I just had the same problem on my TyTN. Everything but the cover and battery was replaced in warranty and now it is solved. It seem to be the connectors to the screen that crack.
southeastblue said:
There's a known problem for HTC Hermes with the D-pas causing white screen, and a little mod to fix it by putting something behind the D-Pad itself such as a small very thin piece of foam. Obviously this requires taking your mobile apart.
Click to expand...
Click to collapse
Read the thread for this and see if you are having the same problem as many of these people. It helped me figure my own problem out a lot. Good luck
Dillsnik said:
Read the thread for this and see if you are having the same problem as many of these people. It helped me figure my own problem out a lot. Good luck
Click to expand...
Click to collapse
This is the same thing that happened to me At&T told me it was the D-pad because that broke before my white screen issue and they replaced it for me
white screen probs
had the same problem on a few hermes now....replaced the screen to no availl....after many other trials i replaced the circuit board under the d-pad and problem sloved.....i havnt got the know how to test the board for faults but i would agree that the board is the problem any one know what the function of the part is exactly....screen controller????
screws...
I had the same problem and was able to fix it temporarily using the foam-behind-the-Dpad-connector trick several (like 6 or 7) times but it always went white again within a few days. I finally got it to stick by loosening the tiny screws on the connector very slightly...haven't had a problem since. I'm not entirely convinced it wasn't just completely luck though. But seriously after so many times trying different thicknesses of foam and banging my head against the wall, I'm glad something worked. And now I can take it apart and put it back together in about 7 minutes, so that's a bonus! Might be worth a try if the foam thing doesn't work. Good luck.
-Nevins
Hey thanks all you guys.. I guess its the D-Pad connector issue.. will follow the resolution suggestions.. I will let you know if that helped...
mine fades to white everyonce in a while then comes back or i have to take the battery out and all is fine. it did it when i put wm6.1 on it. was perfect before i did that.
hi there
ive been having this issue for ages and have opened my handset to reseat the connector no fewer than 14 times in the last 2 weeks
today i had a breakthrough though,
what i did was completely cleaned the connectors using rubbing alcohol and a q-tip
the important bit: RESEAT the connector properly. it may look like its reseated but look at it side on and it should be perfectly flat, and if necessary push on it a little to make sure its seated
then, on the back cover (which you removed to get access to th d-pad) you'll notice a little rectangle 'pad' there roughly in the same place as the d-pad connector
get a white sticky label, or a post-it note or whatever and stick a little piece over that
then seal your phone back up and it should work.
i cant promise anything though, and any damage you do to your phone is entirely your responsibility
Last night I was out and during the night I pulled my desire z out of my pocket to find that the screen was dead, the soft touch buttons were still lit up and working but no display. I pulled the battery and tried to reboot and no luck, you can hear it booting and even unlock/receive calls and txts etc once it has booted up just the screen stays blank the whole time so have to do everything on feel.
Essentially does this just mean my screen has a hardware fault? is it worth trying to fix? I assume the only option would be to purchase a replacement screen and dissemble and reassemble it?
(warranty is not worth it as I live in New Zealand and would have to send my phone back to the UK where I bought it from, also I have dropped it quite a few times so probably voided anyway...)
Thanks in advance for any input
Does it never display anything? So not even a flash during boot or something?
Because then it is probably a hardware problem.
Since the soft touch buttons do still work I think there might be a little crack or something in the flat cable that connects the bottom half with the top.
Maybe you could check whether you can see if the cable is broken or not?
The best thing to do then is to look for a replacement and try to fix it yourself or bring it to a shop where they can do it for you.
No it never displays anything, completely dead the whole time. The touch input is still working though as I answered a phone call this morning on it by making the usual gesture just without being able to see anything. Doesnt seem to be anything wrong with the cable itself as far as I can see. Yea might have to get someone to have a look at it.
My phone is acting the same. I dropped my phone in the pond before, but pulled battery out on time and had it in rice for a day. My phone was still working for about two weeks after that incident. I dropped it and had one little crack at the top of the screen and about a week after that it died when I had a water balloon fight with the phone in my pocket. D;
Do any of you know if the replacement lcd screen/digitizer for the Desire Z would work for the G2?
I had the same thing happening to my G2 screen, only it was intermittently working for a little while, then just completely died and wouldn't work. It was doing this crazy flickering thing then the back light wouldn't go on at all. If I held the phone at a certain angle in the sun, I could see that the pixels were indeed working on the display, but there was no backlight to make them normally visible.
So I purchased a replacement screen from ebay and carefully followed the directions on a youtube video for a G2 take apart. Its not a hard task to take apart and get down to the screen itself. It was rather easy. After putting it back together the screen still didn't work! Sounds work, i can also receive calls etc. But the screen still doesn't work!
Is there any way that this could be a software issue?
Oh and PS, I believe the LCD replacement would work for both the desire Z and the G2. They are identical phones after all right? I'd say its a safe bet. The screen I bought was only 35 bucks. Didn't think that was a bad deal.
Another dead screen or something else?
Few days ago my phone fell of the couch onto a rug - no big deal, so far it has survived much worse, but when I picked it up, the colors were all messed up - overly green and red. Tried restarting - no luck. Everything worked fine, except the colors, but then the screen turned of completely. I could hear notifications, phonecalls, but the screen was dead. After some tapping on the screen, it turned on again - with ****ed up colors. Then started flickering and was gone again. Few more times I could turn it on by tapping before it was dead for good.
Figured, after all these drops it survived, maybe the screen connector is a bit loose. I mean, I could sometime get a contact when tapping it, so I dissasambled it completely, secured all the connection, put it all back tougether and fired up - same thing: dead screen, phone working.
Has anyone had such problem before? Is it screen that is dead, or connector or... I have no clue... I would like try to fix it on my own, with some replacement parts I could get on ebay - but, what gave?
Hey guys i need some help please.
I opened my phone up a few weeks ago to blow out some dust that got in behind the screen. But when I put it all back together again. The phone wouldn't boot, but somehow i got it going again. But since then, whilst using the phone the screen will randomly stop responding and then the phone itself will just crash,
Now, when I go to reboot (I have to take battery out and back in) HTC spalshscreen comes on then the screen just slowly goes off within 15 secs (my splash screen is usually on for about 20 secs and the miui splash comes on straight after when working).
I have to keep rebooting until the phone comes on and then it would work fine for 1-2 days before it plays up again.
If trawled through similar problem but still can find an answer. Please help me out guys, I need to get my phone working again as I can't afford a new one as good as this.
If it helps I have been running on miui xj for about 8 months
Many thanks in advance
Hi i read the other day in the desire s threads and when u took the lcd screen off the digitizer (front of the phone) did u damage the tape glue around the edge that holds them both together? Because if u damage it even the slightest bit it and theres the tiniest gap, it will cause the screen to not work properly and give faulse/positive touchs and the phone to not work correct. Maybe this is not ur problem but i thought id say.
jmcclue said:
Hi i read the other day in the desire s threads and when u took the lcd screen off the digitizer (front of the phone) did u damage the tape glue around the edge that holds them both together? Because if u damage it even the slightest bit it and theres the tiniest gap, it will cause the screen to not work properly and give faulse/positive touchs and the phone to not work correct. Maybe this is not ur problem but i thought id say.
Click to expand...
Click to collapse
Well you theory does make sense, I didn't actually take the digitizer out but I did notice looking through the screen that theres a little gap there thats allowing all the dust to get in there. I have reinstalled ROMs a couple of times now but its still hit and miss. So you could be very right as I don't know what else the problem can be.
Thanks for the response cos I never would have thought of that. I'm gonna strip it properly now and hope to fix it :good:
Nope im still having problems. I reinstall the the rom and itll be ok for a few weeks maybe then itll go on the blink again.
Im starting to wonder if there an issue with the software somewhere. But ive been using this rom for ages and not had a problem with it untill now
The battery on my HTC 10 was completely shot and needed to be replaced. I'm a careful person by nature and this being my first phone repair, I bought an extra screen just in case something happened getting it apart. Followed a guide by jerryrigeverything on how to take apart the phone, got the battery replaced, everything seemed to go smoothly. When I went to test the display before screwing everything together, the new screen I installed lit up, but the right half of the display only showed as a repeating segment from the middle of the screen. Thinking the connector was loose, I disconnected and reconnected the display and made sure everything was tight: same problem. I reinstalled the original display, which I made sure had worked after cutting through the adhesive before I disconnected it, and now the old display is also showing the same issue.
The touch screen on the broken side of the display still works, I'm able to type PIN numbers and whatnot even though I can't see them properly. Only thing I can think of is maybe the connection actually got some debris or something inside of it? I don't think I damaged anything, as I was super careful, but it was also my first time opening up a phone.
Sorry for the inefficiently worded post. Any help would be really appreciated.
Did you resolve this?
I have exactly the same issue you describe after my screen replacement (with two new screens) Believing the first was a dud.
I have done many screens/batteries on my m7, m8's previously never having a problem.
I'm currently back to running my M8 and miss my 10!
Anyone reading this and has any suggestions they are all welcome!!
Thank you in advance
Exactly the same issue this guy has
https://youtu.be/RpdCuMiTOn8
I'm now wondering if it is just bad aftermarket screens?
Has anyone else replaced their screen successfully, if so where did you get the screen?
Thanks Rory
I have been having the same problem. I just tested screen number 4 that has the same exact problem. Is there a specific brand that is known to test well?
I dropped my 10 in water at work...believe it was a salty water at that. It stopped working completely. I opened the phone to check the internal components for damage and I broke the LCD doing so. I replaced the battery and the screen at almost the same time. I think it may have been a week or two apart.
The battery is still working. The screen worked initially but the phone kept getting really hot and the heat kills the phone. I tried keeping it cool at all times which kept it operational. It hasn't been activated since I quickly replaced the phone with another of my lines upgrades. I went back to the phone to check it out and try using it as a replacement for my daughter but the screen no longer works.
The battery charges just fine...the led light indicates that well. I've tried reinstalling it several times with no success getting the screen working again. I tried the original screen to check and I could see light and it was responding but its not usable so I'm stuck with a phone that has a new non-working display. I think the brand was called DIYRepair or similar.
If anyone has encountered this and has advice...I'd be happy to try anything.