Related
Hello
I've searched on this forum and can't find the answer to my specific question.
I upgraded a while back to MrClean AKU 2.3 and now I need to downgrade because the unit needs to be sent back under warranty due to screen alignment issues.
So I unpacked the i-mate WWE ROM, and replaced the ROMUpdateUtility from that with the ROMUpdateUtility_Wizard_NoID.exe, which I downloaded from the XDA FTP site. (This is because using the standard one supplied gives a ROM upgrade error 296: UPGRADE ONLY error.)
As far as I can make out, the ROMUpdateUtility_Wizard_NoID.exe is just patched to not validate the current version when upgrading.
"Brilliant, this should work", I think.
But I get the following error:
"ERROR [238]: FILE READ... the update utility cannot open the requested file. Please check your update utility"
(see here http://static.flickr.com/111/306871020_8aa37f337e_o.gif)
Please help, anyone, I am coming up to the end of my warranty period and reeeeally want to get this crappy broken screen alignment problem sorted!
Thanks in advance
* bump *
Hope it's not considered rude to bump here, just would love to solve this problem as tis driving me a bit mad
Many thanks in advance
msmobiles.com:
This error message may appear when, for some unknown reason, the ROM image on the phone is corrupt. Download the whole RUU and try again.
Click to expand...
Click to collapse
Hey
Thanks for the tip. You were right, it must have been a corrupt .nbf file.
I tried to downgrade and the progress bar started and finished and all seemed to go well.
But when I boot up again I get the white MrClean ROM splash screen still!
Is it possible the update was done but the splash screen was not replaced?
Or perhaps the update wasn't actually done? Which version number do I look for? I used the .nbf file packaged in with the imate ROM K-JAM_WWE_1010903_106_10110_ship.exe
Please help!
try using this rom to downgrade with... after that you should be able to upgrade to any official rom. Make sure that you pick an official one as the above rom downgrades the ipl/spl as well.
ohh... and make sure that you restore the CID lock as well, they might be get rather cranky otherwise...
Good luck
Hello
Thank you so much for the reply, I really appreciate the advice. I would feel so out-there-on-my-own without it! I bought the imate off contract from expansys and it was really expensive and so really don't want it to end up a brick as I can't afford another right now!
I successfully downgraded to that QTEK custom ROM.
But now when I upgrade again to K-JAM_WWE_216901_2169101_020710_ship (latest).exe from that QTEK ROM, it doesn't work! Upgrade error again [ERROR 296]
Here are the screens I get:
http://static.flickr.com/114/309671629_756dc86b9d_o.gif
http://static.flickr.com/107/309671652_327adfb432_o.gif
Thanks again
Mat
Just to clarify... is the phone CID-locked? You might also want to try flashing it with the K-JAM_WWE_1010903_106_10110_ship.exe ROM before upgrading it... you can also try putting the phone in bootloader mode, press and keep pressed both the keys on the right side and then insert the pen in the resetbutton, before trying the upgrade...
EDIT: msmobiles.com shows the following regarding the particular error:
ERROR [296] : UPGRADE ONLY
One of these error messages will appear when you use the wrong RUU to do the upgrade. RUU will check if the Model ID and Language ID are compatible with the device. Make sure you use the appropriate RUU tool to upgrade.
Click to expand...
Click to collapse
Hey Nomad
Thanks again for the advice. This is all really really helpful. Going to try what you suggested a bit later.
I think I CID unlocked the phone - to be honest it was a while ago and I just remember blindly following someone's instructions (I was at a point of desperation at the time for another reason!)
Either way, I am pretty sure it would have to have been CID unlocked because I flashed the ROM from the imate default one to the MrClean one.
I did some initial looking around about CID relocking the device but still not sure how. Does the lockiwiz give the option of locking the CID as well as unlocking it?
Thanks!
Mat
I flashed from the QTEK custom ROM to the K-JAM_WWE_1010903_106_10110_ship.exe after doing that special reset whilst in the bootloader. This flash upgrade worked but again it didn't remove the splash screen from the QTEK custom ROM.
But now whenever I try to flash to the latest imate ROM K-JAM_WWE_216901_2169101_020710_ship.exe using the default RUU I get ERROR [296] UPGRADE ONLY.
And when I try to flash to the same ROM using the noID RUU I get ERROR [238]: FILE READ ERROR.
(On that last one, I have re-downloaded both the noID RUU and the extractable archive K-JAM_WWE_216901_2169101_020710_ship.exe from the XDA FTP.
So, I'm still unable to get my ROM to the imate version! Many thanks for your help!
Mat
Hello,
My model ID disappeared from my phone and now I cannot upload anything to it anymore.. It happened while updating to spl 1.40 Olinex... Does anyone have an idea how to upload a Rom without the need of a Device ID? The spl has the right number (I can see that in the Bootloader screen)...
Help?
xanh said:
Hello,
My model ID disappeared from my phone and now I cannot upload anything to it anymore.. It happened while updating to spl 1.40 Olinex... Does anyone have an idea how to upload a Rom without the need of a Device ID? The spl has the right number (I can see that in the Bootloader screen)...
Help?
Click to expand...
Click to collapse
This has happen to my phone as well can you go to bootloader mode and write down all the details here, we might have to contact ccmonex/olinex if its the same which happpen to me,
xanh said:
Hello,
My model ID disappeared from my phone and now I cannot upload anything to it anymore.. It happened while updating to spl 1.40 Olinex... Does anyone have an idea how to upload a Rom without the need of a Device ID? The spl has the right number (I can see that in the Bootloader screen)...
Help?
Click to expand...
Click to collapse
hey. dutty showed me this thread drop me a PM and we can try and fix this.
basically we'll first try to write your modelid back, if that doesn't work, then the last option is flash an SPL that ignores modelid.
cmonex said:
hey. dutty showed me this thread drop me a PM and we can try and fix this.
basically we'll first try to write your modelid back, if that doesn't work, then the last option is flash an SPL that ignores modelid.
Click to expand...
Click to collapse
thanks for responding so fast hope it isnt that bad like it was mines
Thanks for your quick reply's..
Here's my info:
MFG 64M
SPL-1.40.OliNex
MicroP-Diam (LED) v11
PSOC-Diam STAGE_PVT v0x30
If I take out the battery I can see DIAM100 in the case...
xanh said:
Thanks for your quick reply's..
Here's my info:
MFG 64M
SPL-1.40.OliNex
MicroP-Diam (LED) v11
PSOC-Diam STAGE_PVT v0x30
If I take out the battery I can see DIAM100 in the case...
Click to expand...
Click to collapse
just pm cmnonex and she will guide you
Another problem is with mtty..
When I start up the program and my phone in boot loader, then mtty crashes immediately when I press a button.. If I disconnect usb and reconnect it again I can type stuff in, but I can type in text without anything happening..
I'm starting to give up on this phone. Maybe I should start seeing it as a expensive pda..
i have the same issue .. me phone is freez then i have to remove battery out .. and restart again ... BUT ... everything is gone ... i cannot doing anything with it ....doesnt matter what kind the rom i upgrade .. still came bootloader ONLY ... i have read many thread about BRICK ... but nothing could help ......please any advise .... HELPP..... please
First of all :
Relax
Got a new diamond today and had the same issues.
What Windows OS are you using ? Do you use WDMC or Activesync ?
What is the driver version of the installed HTC Sync ?
As for mtty :
Next version of QMAT will be fine and will be much more stable than mtty.
As for bootloader :
1. Are you able to connect to mtty, and does it respond to command
"info 2" ?
If yes, fixing it should be no problem.
Contact cmonex, she will be able to help you.
If she isn't able, I and cmonex will figure out what to do next
Cya,
Viper BJK
viperbjk said:
First of all :
Relax
Got a new diamond today and had the same issues.
What Windows OS are you using ? Do you use WDMC or Activesync ?
What is the driver version of the installed HTC Sync ?
As for mtty :
Next version of QMAT will be fine and will be much more stable than mtty.
As for bootloader :
1. Are you able to connect to mtty, and does it respond to command
"info 2" ?
If yes, fixing it should be no problem.
Contact cmonex, she will be able to help you.
If she isn't able, I and cmonex will figure out what to do next
Cya,
Viper BJK
Click to expand...
Click to collapse
Thanks for quick reply VIPER ... my phone run well until i remove the battery ... everything turn out bad ....i use stock rom with is HK version 1.93.871.1
seem to me usb working fine... i can upgrade it ...but ... when is done ...only have bootloader ...First come with ::: DIAMOND TOUCH :: then black out ..when i press power button again .. coming only bootloader screen, no matter what rom i try ... still in bootloader mode.........please help .......
was a double message
viperbjk said:
First of all :
Relax
Got a new diamond today and had the same issues.
What Windows OS are you using ? Do you use WDMC or Activesync ?
What is the driver version of the installed HTC Sync ?
As for mtty :
Next version of QMAT will be fine and will be much more stable than mtty.
As for bootloader :
1. Are you able to connect to mtty, and does it respond to command
"info 2" ?
If yes, fixing it should be no problem.
Contact cmonex, she will be able to help you.
If she isn't able, I and cmonex will figure out what to do next
Cya,
Viper BJK
Click to expand...
Click to collapse
Hi Viper,
Thanks for your reply,
Unfortunately qmat crashes too when I try to send it a command... The version I use here is v395..
I'm using Activesync 4.5.. But this has been disabled...
After a while windows tells me that it finds an unknown device when in bootloader..
The OS is still working and is a HK version 1.93.871.1 as well..
Although I don't know if the OS part is fully ok, since after a hard reset the extra programs get installed and the phone crashes on installing opera...
Could it be that the bootloader itself is not functioning properly making all the tools crash?
My idea is to change the id of the phone to be able to upload a new SPL, and upload a original ROM... At least it should work again then... But I've been trying for more than a week now..
Thanks..
Xanh, which spl is now installed on your device ?
If it is the Hard Spl, try manualspl to reflash spl again. I guess SPL is broken.
Normally, you don't need to change the ID for that.
Changing the ID is only needed when flashing a ROM other than your
original one.
k3vin168 : Also try to reflash SPL. If you've done that and it did work, please contact me via PM. Then either your nand is bad or you need to change the bootmode.
Cya,
Viper BJK
SPL is 1.40.OliNex, but I don't need to change the ID, but it's missing since failing installing 1.40.OliNex SPL.. How does this manual SPL upload work?
No matter which update I try, it will always say that Device ID is wrong... I think NAND is somehow bad, since that's where the device ID is stored right?
xanh,
Could be that nand is bad. There are two regions where the device id is stored.
Memory and NAND. But both can be fixed using Hard SPL (MFG).
PM me, I'll try to help you out of your misery.
k3vin168 said:
Thanks for quick reply VIPER ... my phone run well until i remove the battery ... everything turn out bad ....i use stock rom with is HK version 1.93.871.1
seem to me usb working fine... i can upgrade it ...but ... when is done ...only have bootloader ...First come with ::: DIAMOND TOUCH :: then black out ..when i press power button again .. coming only bootloader screen, no matter what rom i try ... still in bootloader mode.........please help .......
Click to expand...
Click to collapse
Any progress on this one ?
If not, please PM me
xanh said:
SPL is 1.40.OliNex, but I don't need to change the ID, but it's missing since failing installing 1.40.OliNex SPL.. How does this manual SPL upload work?
No matter which update I try, it will always say that Device ID is wrong... I think NAND is somehow bad, since that's where the device ID is stored right?
Click to expand...
Click to collapse
he meant SSPL-Manual.exe from the hardspl thread, but I don't think that would fix mtty.
anyway, have you got my PM. if mtty is hopeless, the other route is what you need (flash SPL without modelid check via special no checking SSPL). I sent you all links and instructions.
(I'd rather not make the files public or all the noobs will start flashing random devices' roms.)
EDIT: I assume your OS is able to boot, but if not, then you need a different set of files, let me know
viperbjk said:
xanh,
Could be that nand is bad. There are two regions where the device id is stored.
Memory and NAND. But both can be fixed using Hard SPL (MFG).
PM me, I'll try to help you out of your misery.
Click to expand...
Click to collapse
for duttythroy, we could not write the modelid back to nand for some reason. lnb said success, then it was still not there in the flash when reading it out afterwards. so I just had him flash a "special" spl
k3vin168 said:
i have the same issue .. me phone is freez then i have to remove battery out .. and restart again ... BUT ... everything is gone ... i cannot doing anything with it ....doesnt matter what kind the rom i upgrade .. still came bootloader ONLY ... i have read many thread about BRICK ... but nothing could help ......please any advise .... HELPP..... please
Click to expand...
Click to collapse
what is your SPL version in tricolour screen?
cmonex said:
what is your SPL version in tricolour screen?
Click to expand...
Click to collapse
i use same as other 1.40 i try all VIPER try to help me out ... but all not working ....just stuck in splash screen ..i try all kind of ROM but still stuck ...i can i do ?? please help
Hello XDA Friends!
I have done 2 solid nights of reading now - not to say I am in the least bit an expert, but this is my second experience with flashing htc phones (previously had a htc wizard). I am not a complete newb, but I have a few unanswered questions before i jump in balls deep.
1) After searching the forums, I have found that I seem to have a (rare) ROM version - 1.93.422.4 WWE to be exact. It is the stock US 3G GSM ROM. It appears that others have (after hardSPL) successfully flashed their Diamonds accordingly with European versions. I went to HTC's website and registered my Diamond and they told me that they do not have a down-loadable version of their ROM (an official HTC ROM) for the 3G US version. HTC simply does not make a version for US 3G that they release.
-"Unfortunately, after some checking on our website with your serial numbers, we have found that currently there is no ROM update for your devices. From our experience, there is almost never an update developed for unlocked US GSM devices. The way we release our updates is we develop them first (after receiving the operating system from Microsoft). Then the carrier or vendor takes the update and modifies it to fit their policies and we release it. Unfortunately, the vendor that usually sells unlocked US devices does not complete the last step." -HTC
This concerns me as this is my fallback in the event things do not go so well for me while flashing. SOOOO all that said, does anyone have a copy of the ROM lying around for my backup benefit!?!
2) Can anyone with a US diamond verify that they are indeed running with a cooked ROM (and be so kind as to suggest which one they prefer?). Obviously its trial and error, but stability and speed are high on the priority list (stock is SOOOO SLOOOW)!
3) The hard reset is confusing me. HTC rep said that if i do a hard reset that it will restore the device to factory settings, thus no need for me to download a ROM to restore the device (i obviously did not tell him i was looking into cooked ROMS!).
-" As far as a ROM that would restore the device, you would simply need to do a hard reset in the even that the ROM became corrupt. This would restore the device to factory defaults. " - HTC
This would indicate that the ROM is somewhere on the internal 4gb storage and copies itself back to the ROM. Is this erased when upgrading ROMS or becomes unavailable after going to hardspl? or would i still have the option to hard reset (take the red pill) and wake up believing that my dance with cooked ROMS was a dream!?!?
Thanks for all your help - fire away - I have thick skin. I'm sure someone will point out my lack of research skills ;p
Long live Xda,
-Nate
I have an unlocked US GSM also. I also tried to get it off the site and it said it was not for my device...
HTC support is pretty much useless, I called and they told me over the phone that my phone wont run WWE roms and that i needed US roms and i told them thats funny because it came preloaded with 1.93WWE.
Anyways The New official rom will work on your phone and its allot faster than the 1.93
First the Hard SPL i used this.
I use this RUU_Signed_1_93OliNex_HSPL_UnsignedEdition
http://forum.xda-developers.com/showthread.php?t=400950
And if you want the official 2.03 WWE ROM its here
Want this one
RUU_Diamond_HTC_WWE_2.03.405.2_Radio_Signed_Diamond_52.51.25.26_1.09.25.23_Ship
http://forum.xda-developers.com/showthread.php?t=471699
I haven't used any cooked ROMS yet so i cant help you out there
Awesome - thanks for the info - that was exactly what i was looking for! Yea... the fact that it says WWE in the ROM is completely contradicting - HTC tech support doesn't seem to know whats going on.
Have you tried the hard reset since you loaded the new ROMs? does it revert to 1.93?
Thanks again for posting,
-Nate
ok all,
flashed to hardSPL olinex 1.40, confirmed in the bootloader, tried to flash to 2.03WWE (as referred to me from above) and it gives me:
Error [244] : invalid model ID
This update utility cannot be used for your pda phone. please check your update utility.
OK. from reading i gather this is because something is wrong with hardSPL? what hardSPL should i use? Or is it another issue entirely?
thanks,
-Nate
btw - after hardSPL, and hard reset, everything on the internal storage is there
perhaps i need to be more specific. When i enter the bootloader, it says:
DIAM100 MFG 64M
SPL-1.40.OliNex
what the bible says it should say is
Hard SPL 1.40.Olinex
DIAM100 MFG 64M
SPL-1.40.OliNex
Does this mean that it did not upgrade correctly? Any ideas? Im trying win 1.37 OliNex
again it says in the bootloader
DIAM100 MFG 64M
SPL-1.37.OliNex
lets me get all the way to 99% and then fails with
Error 270 :update error
The image file is corrupt. please check your update utility.
I need some help guys. Starting to get a little frustrated do you have to update the radio rom before it will take the main rom?
-Nate
Ok, next update. Could not get any of the olix hard SPLs to work. I have tried to upgrade to hardSPL 1.24 per this thread
http://forum.xda-developers.com/showthread.php?t=408621
only problem is that the phone does not ever boot into windows. When i go into the bootloader, it still shows olix 1.37 hard SPL. I have tried re-downloading the file. So far it gets to 100% of the ROM flash and then throws the error 270. Any thoughts?
I never had this problem but on the page were you got the ROM they say if your having issues installing through the update utility to do this.
Rename ..NBH file to DIAMIMG.nbh
Copy to Internal Storage
Soft Reset + Hold volume down button + back button <--
Follow instructions on screen
Anymore problems just read this through the thread were you got the ROM your not the only one who got the "corrupted 270 error".
But flashing it from the storage card should work . ..Goodluck
http://forum.xda-developers.com/showthread.php?t=471699
Ok all,
I have had a hell of a time getting a rom that will install. I could repeatedly get to the bootloader without a problem, and every rom i flashed after installing olinex 1.37 allowed me to get all the way to 100% but would then tell me that the rom was corrupt.
I downloaded and installed Shaks rom, version 3.20 from
http://diamond.geg0r.de/index.php?dir=Shaks/V3.20/
AND ITS BACK INTO WINDOWS!!!!!! thanks GOD!
I will report on further issues i have with the device.
-Nate
When I try to burn the 2.03 WWE ROM mentioned onto my stock US Diamond I get: Error 294: Invalid Vendor ID.
Any ideas what I need to do? I did not change the SPL - must I do that?
I read through the referenced threads and see where people with Error 270 need to put the image file onto internal storage but I have been hesitant to try that since it for Error 270 and not necessarily Error 294.
Any ideas?
Thanks!
wpsantennas said:
When I try to burn the 2.03 WWE ROM mentioned onto my stock US Diamond I get: Error 294: Invalid Vendor ID.
Any ideas what I need to do? I did not change the SPL - must I do that?
I read through the referenced threads and see where people with Error 270 need to put the image file onto internal storage but I have been hesitant to try that since it for Error 270 and not necessarily Error 294.
Any ideas?
Thanks!
Click to expand...
Click to collapse
You need to upgrade to HardSPL.
demo23019 said:
I never had this problem but on the page were you got the ROM they say if your having issues installing through the update utility to do this.
Rename ..NBH file to DIAMIMG.nbh
Copy to Internal Storage
Soft Reset + Hold volume down button + back button <--
Follow instructions on screen
Anymore problems just read this through the thread were you got the ROM your not the only one who got the "corrupted 270 error".
But flashing it from the storage card should work . ..Goodluck
http://forum.xda-developers.com/showthread.php?t=471699
Click to expand...
Click to collapse
Here is the Rom only if anybody wants to flash it. You will not get the invalid ID error.
http://www.sendspace.com/file/iesg1h
Thanks for everybody's help. Burning the new SPL did the trick.
Have tweaked everything pretty much back to how I like it and am quite happy with the new ROM. My only complaint is that I prefer the larger Compact QWERTY keypad of the 1.93 ROM since I have fat fingers. I know that I can dig that keypad up elsewhere but I'll try to get used to the new one first.
Thanks again.
Guys,
I'm new to this web site and am trying to reflash my Touch Pro 2 with the Win 6.5 version. It won't load as previously reported by others, with the fix being, using Hardspl(whatever that is). In trying to download the zipped version of Hardspl from this site, Norton Antivirus rejects it as being infected.
Any assistance here please?
We need more info about your phone, and what you have tried.
I don't know how much info you need but it is an unlocked Touch Pro 2 phone, ROM Version 1.19.401.0(51489), ROM Date 05/16/09, Protocol version 61.32t.25.26U, CPU QUALCOMM(R) 7200A, Model no. HTC Touch Pro 2 T7373.
I downloaded the Europe version of the update from this site RUU_Rhodium_S_HTC_Europe_1.86.401.0_Radio_Rhodium_4.49.25.17_Signed_Ship(2).exe and tried to reflash the phone, having achieved sync. An error message " ERROR(294) : INVALID VENDER ID" comes up, telling me that "This update utility cannot be used for your PDA phone."
I have subsequently seen on this site that a fix was to use Hardspl.
After searching on Xda, I found this download "Rhodium-HardSPL_V2_00R3_185HSPL.zip".
When I try to unzip it I get a message that it is blocked by Norton "Auto protect has detected Bloodhound.W32.EP"
So nothing can happen under these circumstances. What is this Hardspl and why is it necessary?
Would a hard reset help?
Any assistance will be greatly appreciated.
Kind regards Chris
PS Radio version 3.46.25.30
to say it as simple as possible:
your phone has ID, called CID
normal phones only allow ROMs with same CID
HardSPL allows any ROM, skips checking of th CID
positives: you can use ROMs for different parts of the world, debrand your device (not SIM unlock!) and also use unsigned ROM (ROMs that have been modified)
negatives: if you are stupid you can flash a ROM for completely different device and brick your phone, you should put it to previous state before any warranty repairs (to do this first flash original ROM and then remove HardSPL)
As stated in the first post of the Hard SPL and the "Noobs flashing guide" the virus is a false positive.
We were all noobs at one point or another, just take your time to read the stickies about how to flash your device, then upgrade to the 6.5 ROM (or any other custom TP2 ROM on this fourm).
EDIT: Any more problems, please post in the "for noobs" thread.
Thanks
Dave
i have a new htc from t mobile i bought it from craigslist and i was proced to hard spl by this version Rhodium-HardSPL_V2_00R3_185HSPL.zip then i have a message that mean theflashage is done then i make a update to Rhodium_AF|HTC Sense 2.5|LEO 1.43 when it finish the phone doesnt work its stoped at the white screen and stays there im too upsed help me plssss
modelid RHOD210
Ok, please come down...
Let me guide and help you...
First of all it is good that you have done Hard-SPL !
So, if you ROM went BAD and you can not do anything with your Rhodium...
There is a thing that you can do...
Please, follow those steps:
1. Take the cover of the cell phone, and search for the SOFT-RESET hole at the
RIGHT (other side from the VOLUME up/down).
2. Press the VOLUME DOWN, hold it and than SOFT-RESET.
It will take you to tree colour page for BootLoader screen.
3. Connect the device to the computer and try to Flash the ROM again
(or other ROM...).
Good Luck !!
Any help, just ask for it...
hi
Doesn't work from boot laoder too I think the is no radio flash because I can't see olinex in trial color just 5 or 6 Kobe of numr
i think the Hard SPL V2_00R3_185 file you downloaded is corrupted. i also downloaded today but couldn't extract it.
That s mean my device is brick dead
Try this: Download any GSM ROM from this forum (I like EnergyROM Leo), unzip it, and rename the .nbh to "RHODIMG.nbh" (without the quotes) if it isn't already called that. Copy that onto a MicroSD card (that is formatted to FAT32), and put that in your device. Now, go into the bootloader (power off the device, then press Power and Volume Down) then follow the instructions. Hopefully you just had a bad flash, and reflashing will solve it.
I will try but I think my phone is no radio flashed yet bcuz I can't see olinex in bootloader
correzzola said:
I will try but I think my phone is no radio flashed yet bcuz I can't see olinex in bootloader
Click to expand...
Click to collapse
Oh, if it doesn't say 0.85.OliNex, then you're still on a stock SPL, so my suggestion won't work. Try flashing the TMobile stock ROM for your device, and retry the HardSPL process (I would advise redownloading everything to ensure it's not corrupt).
So how canine flash t mObile stock rom
0.79.0000 stock SPL
i have this number in tricolor that mean my device is Relocker bcuz i m was make it by RhodiumSPLRelocker_079SPL.zip so now the phone dosnt accdpte flashage by Rhodium-HardSPL_V1_20R2_185HSPL.zip
this is a tricolor screen
RHOD210 32M SS-BC
SPL-0.79.0000
MicroP-Rhodium (LED) vA
MicroP-Rhodium (LED) v4
turbo HW/TURBO SW
TP MFG DATA
504,522,816,847
808,192,195,192
201,849 calibrated
and this is my start page froozen its stay here with this nuber down left
B 80
R 3.45.25.14
P 61.27t.25.23u
D Energy ROM
correzzola said:
0.79.0000 stock SPL
i have this number in tricolor that mean my device is Relocker bcuz i m was make it by RhodiumSPLRelocker_079SPL.zip so now the phone dosnt accdpte flashage by Rhodium-HardSPL_V1_20R2_185HSPL.zip
Click to expand...
Click to collapse
have you tried reflash HardSPL_v1_20R_185HSPL yet?
It also might helps you guys...
I have managed a Full Package of Hard-Spl Oilnex that WORKS!
Download the Package here...
After download and UnRAR it, you will find anything you need for Hard-Spl and the Original Tutorial
For Flash and for Stock Restore...
Enjoy!
Calm down
First of all, posting 2 new threads and commenting in the NRG thread is called spamming, stop it. It'll be much easier for you to get the help you need by sticking with one thread (I imagine the Mod is going to do that for you). Second, blasting your email address and phone number publically is bad practice, you open yourself up for a massive email spam list and phone pranks. I suggest you go in and edit your post as soon as possible and delete that information out. Thirdly, I'm guessing English is not your native language, if it isn't I suggest typing the problem out in your own language, use a translation software (I think Google Docs has this feature), and post the translation into the forum. This will help with clarity of what's going on.
Now with all that said, my final suggestion would be to tell us exactly what you have done to the phone IN THE ORDER that you've done it, up until the point that you're at now. Also, being that you bought this phone off a craigslist (another mistake imho, I'd rather just spend the extra $$ for the warranty and piece of mind that it's from the manufacturer/carrier directly), tell us what condition the phone was in to begin with. Did it come with NRGZ ROM preloaded, or the stock ROM? Was it locking up before you decided to reflash? Did you read the Flashing Guide stickied to the top of this forum before flashing your phone? (If not, let this serve as a reminder to all other newbie's looking to flash to READ BEFORE YOUR MOD!)
We're going to try and help you, correzzola, but you need to take a breath and calm down. It's just a phone, granted a lot of money, but you're not suffering onto the point of bloodshed so it's all going to be okay.
From the look of it, you HardSPL'd, flashed a cooked ROM, then removed HardSPL. Huh... that's probably not good. Try flashing this T-Mobile US ROM (I'm assuming you have a T-Mobile US TP2) while in the bootloader, and see if that solves it (or even flashes at all). If that doesn't work, I'm honestly not 100% sure what to do next, since I've never heard of anyone doing this before.
Firstly, STOP SPAMMING THE BOARD!!! - you will only annoy people and make them less likely to help you.
Secondly, Read what Dave (the Tytn Guy) has posted and let us know what happens, any more problems post in this thread and I'll see what I can suggest.
Dave
itry this rom too but doesnt work TMOUS Stock Shipped Rom 1.20.531.4 (51986) WWE
i think this step is responsable of my probleme Stock/Shipped SPL by RhodiumSPLRelocker_079SPL.zip