Is it bricked? - Touch Diamond, MDA Compact IV ROM Development

Hello,
My model ID disappeared from my phone and now I cannot upload anything to it anymore.. It happened while updating to spl 1.40 Olinex... Does anyone have an idea how to upload a Rom without the need of a Device ID? The spl has the right number (I can see that in the Bootloader screen)...
Help?

xanh said:
Hello,
My model ID disappeared from my phone and now I cannot upload anything to it anymore.. It happened while updating to spl 1.40 Olinex... Does anyone have an idea how to upload a Rom without the need of a Device ID? The spl has the right number (I can see that in the Bootloader screen)...
Help?
Click to expand...
Click to collapse
This has happen to my phone as well can you go to bootloader mode and write down all the details here, we might have to contact ccmonex/olinex if its the same which happpen to me,

xanh said:
Hello,
My model ID disappeared from my phone and now I cannot upload anything to it anymore.. It happened while updating to spl 1.40 Olinex... Does anyone have an idea how to upload a Rom without the need of a Device ID? The spl has the right number (I can see that in the Bootloader screen)...
Help?
Click to expand...
Click to collapse
hey. dutty showed me this thread drop me a PM and we can try and fix this.
basically we'll first try to write your modelid back, if that doesn't work, then the last option is flash an SPL that ignores modelid.

cmonex said:
hey. dutty showed me this thread drop me a PM and we can try and fix this.
basically we'll first try to write your modelid back, if that doesn't work, then the last option is flash an SPL that ignores modelid.
Click to expand...
Click to collapse
thanks for responding so fast hope it isnt that bad like it was mines

Thanks for your quick reply's..
Here's my info:
MFG 64M
SPL-1.40.OliNex
MicroP-Diam (LED) v11
PSOC-Diam STAGE_PVT v0x30
If I take out the battery I can see DIAM100 in the case...

xanh said:
Thanks for your quick reply's..
Here's my info:
MFG 64M
SPL-1.40.OliNex
MicroP-Diam (LED) v11
PSOC-Diam STAGE_PVT v0x30
If I take out the battery I can see DIAM100 in the case...
Click to expand...
Click to collapse
just pm cmnonex and she will guide you

Another problem is with mtty..
When I start up the program and my phone in boot loader, then mtty crashes immediately when I press a button.. If I disconnect usb and reconnect it again I can type stuff in, but I can type in text without anything happening..
I'm starting to give up on this phone. Maybe I should start seeing it as a expensive pda..

i have the same issue .. me phone is freez then i have to remove battery out .. and restart again ... BUT ... everything is gone ... i cannot doing anything with it ....doesnt matter what kind the rom i upgrade .. still came bootloader ONLY ... i have read many thread about BRICK ... but nothing could help ......please any advise .... HELPP..... please

First of all :
Relax
Got a new diamond today and had the same issues.
What Windows OS are you using ? Do you use WDMC or Activesync ?
What is the driver version of the installed HTC Sync ?
As for mtty :
Next version of QMAT will be fine and will be much more stable than mtty.
As for bootloader :
1. Are you able to connect to mtty, and does it respond to command
"info 2" ?
If yes, fixing it should be no problem.
Contact cmonex, she will be able to help you.
If she isn't able, I and cmonex will figure out what to do next
Cya,
Viper BJK

viperbjk said:
First of all :
Relax
Got a new diamond today and had the same issues.
What Windows OS are you using ? Do you use WDMC or Activesync ?
What is the driver version of the installed HTC Sync ?
As for mtty :
Next version of QMAT will be fine and will be much more stable than mtty.
As for bootloader :
1. Are you able to connect to mtty, and does it respond to command
"info 2" ?
If yes, fixing it should be no problem.
Contact cmonex, she will be able to help you.
If she isn't able, I and cmonex will figure out what to do next
Cya,
Viper BJK
Click to expand...
Click to collapse
Thanks for quick reply VIPER ... my phone run well until i remove the battery ... everything turn out bad ....i use stock rom with is HK version 1.93.871.1
seem to me usb working fine... i can upgrade it ...but ... when is done ...only have bootloader ...First come with ::: DIAMOND TOUCH :: then black out ..when i press power button again .. coming only bootloader screen, no matter what rom i try ... still in bootloader mode.........please help .......

was a double message

viperbjk said:
First of all :
Relax
Got a new diamond today and had the same issues.
What Windows OS are you using ? Do you use WDMC or Activesync ?
What is the driver version of the installed HTC Sync ?
As for mtty :
Next version of QMAT will be fine and will be much more stable than mtty.
As for bootloader :
1. Are you able to connect to mtty, and does it respond to command
"info 2" ?
If yes, fixing it should be no problem.
Contact cmonex, she will be able to help you.
If she isn't able, I and cmonex will figure out what to do next
Cya,
Viper BJK
Click to expand...
Click to collapse
Hi Viper,
Thanks for your reply,
Unfortunately qmat crashes too when I try to send it a command... The version I use here is v395..
I'm using Activesync 4.5.. But this has been disabled...
After a while windows tells me that it finds an unknown device when in bootloader..
The OS is still working and is a HK version 1.93.871.1 as well..
Although I don't know if the OS part is fully ok, since after a hard reset the extra programs get installed and the phone crashes on installing opera...
Could it be that the bootloader itself is not functioning properly making all the tools crash?
My idea is to change the id of the phone to be able to upload a new SPL, and upload a original ROM... At least it should work again then... But I've been trying for more than a week now..
Thanks..

Xanh, which spl is now installed on your device ?
If it is the Hard Spl, try manualspl to reflash spl again. I guess SPL is broken.
Normally, you don't need to change the ID for that.
Changing the ID is only needed when flashing a ROM other than your
original one.
k3vin168 : Also try to reflash SPL. If you've done that and it did work, please contact me via PM. Then either your nand is bad or you need to change the bootmode.
Cya,
Viper BJK

SPL is 1.40.OliNex, but I don't need to change the ID, but it's missing since failing installing 1.40.OliNex SPL.. How does this manual SPL upload work?
No matter which update I try, it will always say that Device ID is wrong... I think NAND is somehow bad, since that's where the device ID is stored right?

xanh,
Could be that nand is bad. There are two regions where the device id is stored.
Memory and NAND. But both can be fixed using Hard SPL (MFG).
PM me, I'll try to help you out of your misery.

k3vin168 said:
Thanks for quick reply VIPER ... my phone run well until i remove the battery ... everything turn out bad ....i use stock rom with is HK version 1.93.871.1
seem to me usb working fine... i can upgrade it ...but ... when is done ...only have bootloader ...First come with ::: DIAMOND TOUCH :: then black out ..when i press power button again .. coming only bootloader screen, no matter what rom i try ... still in bootloader mode.........please help .......
Click to expand...
Click to collapse
Any progress on this one ?
If not, please PM me

xanh said:
SPL is 1.40.OliNex, but I don't need to change the ID, but it's missing since failing installing 1.40.OliNex SPL.. How does this manual SPL upload work?
No matter which update I try, it will always say that Device ID is wrong... I think NAND is somehow bad, since that's where the device ID is stored right?
Click to expand...
Click to collapse
he meant SSPL-Manual.exe from the hardspl thread, but I don't think that would fix mtty.
anyway, have you got my PM. if mtty is hopeless, the other route is what you need (flash SPL without modelid check via special no checking SSPL). I sent you all links and instructions.
(I'd rather not make the files public or all the noobs will start flashing random devices' roms.)
EDIT: I assume your OS is able to boot, but if not, then you need a different set of files, let me know

viperbjk said:
xanh,
Could be that nand is bad. There are two regions where the device id is stored.
Memory and NAND. But both can be fixed using Hard SPL (MFG).
PM me, I'll try to help you out of your misery.
Click to expand...
Click to collapse
for duttythroy, we could not write the modelid back to nand for some reason. lnb said success, then it was still not there in the flash when reading it out afterwards. so I just had him flash a "special" spl

k3vin168 said:
i have the same issue .. me phone is freez then i have to remove battery out .. and restart again ... BUT ... everything is gone ... i cannot doing anything with it ....doesnt matter what kind the rom i upgrade .. still came bootloader ONLY ... i have read many thread about BRICK ... but nothing could help ......please any advise .... HELPP..... please
Click to expand...
Click to collapse
what is your SPL version in tricolour screen?

cmonex said:
what is your SPL version in tricolour screen?
Click to expand...
Click to collapse
i use same as other 1.40 i try all VIPER try to help me out ... but all not working ....just stuck in splash screen ..i try all kind of ROM but still stuck ...i can i do ?? please help

Related

Stuck at Splash screen. Help!

Hello.
After upgrading, my Universal dont boot. It's locked at operator start screen.
Hard reset dont unlock it from splash screen.
If I press (ligth + soft reset), select Clean Registry Hive and Format Storage to YES, then reboots and the screen goes to WHITE.
I dont know what is happening...
SOme help please.¡
Try putting it on Boot Loader Mode and flash it back with the old ROM.
Im sorry but the problem it's that i dont have OLD rom :x
see that: http://forum.xda-developers.com/viewtopic.php?t=43592
:wink:
see that: http://forum.xda-developers.com/viewtopic.php?t=43592
:wink:
Any of this post has worked...
Readed from beginning to end.
The Universal upgrade goes well, reboot well, but frezee at logo screen...
Any idea?
jjgarcia said:
Any of this post has worked...
Readed from beginning to end.
The Universal upgrade goes well, reboot well, but frezee at logo screen...
Any idea?
Click to expand...
Click to collapse
Have you tried flashing it back to the OLD ROM or the PREVIOUS ROM you have used and worked on your unit? Try finding another link to download your NEW ROM, sometimes files get corrupted.
I tested with a lot of roms, imate, qtek, t-mob... but nothing works,... i will try to get an original rom and flash from SD card...
get connected :?
bad bad bad, not working...
:evil:
i have the same problem i also, stuck at the splash screen. i have bootloader v1.01 i first unlocked my mda pro with the buzz programm after that i flashed wit the tmobile rom. and it got stuck i reflashed it wit my old qtek rom and it still freezes at the qtek screen.
I think the problem lies on your Boot Loader version. Most of the LATER released ROM is using Boot Loader version 1.00. So anyone who flashed their device with the latest T-Mobile ROM without removing the bl.nbf file got updated to version 1.01. Thus any ROM you try to use won't work.
Try flashing your devices back with Boot Loader version 1.0, then use the old ROMs.
Yes, i have the 1.01 bootloader...
How Can I downgrade to 1.00?
Thanks in advance¡ :wink:
Some idea in downgrade bootloader?
. .. .. .. ... .. .. :roll:
jjgarcia said:
Some idea in downgrade bootloader?
. .. .. .. ... .. .. :roll:
Click to expand...
Click to collapse
Here you go my friend. Just follow the instructions from this thread: http://forum.xda-developers.com/viewtopic.php?t=48590&highlight=boot+loader+1+00
Good Luck Mate!
The solution dindnt worked, because the COUNTRY ID¡¡¡
In the post anybody solved this problem. How can i upgrade? The MaUpgrade_NoID do NOT work.
i downgraded the bootloader tot v1.00 but it still doesnt work wit the old Qtek WWE rom is used before. what to do now...
how do you downgrade? no country-id error?
shing said:
i downgraded the bootloader tot v1.00 but it still doesnt work wit the old Qtek WWE rom is used before. what to do now...
Click to expand...
Click to collapse
You have to use the Ma_Upgrade_No_ID Tool and I made a short instructions on how to use it in this thread: http://forum.xda-developers.com/viewtopic.php?t=42784&start=50
AND REMEMBER to put your device on Boot Loader Mode before double clicking the Ma_Upgrade_No_ID Tool.
cktlcmd said:
shing said:
i downgraded the bootloader tot v1.00 but it still doesnt work wit the old Qtek WWE rom is used before. what to do now...
Click to expand...
Click to collapse
You have to use the Ma_Upgrade_No_ID Tool and I made a short instructions on how to use it in this thread: http://forum.xda-developers.com/viewtopic.php?t=42784&start=50
AND REMEMBER to put your device on Boot Loader Mode before double clicking the Ma_Upgrade_No_ID Tool.
Click to expand...
Click to collapse
yeah, i already did that, but what i wanted to say. it succefully downgraded the bootloader from v1.01 to v1.00. and it also succesully upgraded the Qtek WWE rom. but it is still stuck at the splash screen (the screen shows QTEK wit a sky background and it shows the R 1.09.00 G 42.42.P8 D1.30.77 WWE)
jjgarcia said:
how do you downgrade? no country-id error?
Click to expand...
Click to collapse
i had no country error, i put my mda in bootloader mode and i used the v1.00 bootloader upgrade from the link that the guy posted in this thread.

URGENT help on Hard SPL screen

Hello,
I executed the Hard SPL cab and went into bootloader or some sort of a multi colored screen which says IPL - 0.50 Trin100 and underneath it says SPL 3.03.0000. It connects to my computer and says USB but when I attempt to flash the new WM6 rom which I just downloaded from the rapidshare it resets the machine and continues to remain on this screen of multi colored stuff. I cannot seem to get out of it no matter what I do. What do i need to do to abort the multi colored screen or allow it to flash my HTC trinity with the Dopod WM6 rom?
Thanks,
Gilbert
PS: please don't shoot me if this was discussed elsewhere. i searched and could not fine anyting
happened to me yesterday.
with this screen install AGAIN the hard....
see
http://forum.xda-developers.com/showthread.php?t=316113
and
http://forum.xda-developers.com/showthread.php?t=312499 -page 45
How? I try to execute again the Hard SPL file and it gives me an error and says close window on PC.
Thanks,
Gilbert
it keeps giving me error in connection and i think i bricked my phone i tried to reinstall several times and i get the same results. Poor me.
Same hapen to me, then ive tried to instal over it a another rom and it came to life.
if you're in the bootloader already, try and run the RUU (update program) again on your pc after reconnecting your device.. if that doesn't work, please give details of the error. I don't think you're bricked yet
racerx_ said:
if you're in the bootloader already, try and run the RUU (update program) again on your pc after reconnecting your device.. if that doesn't work, please give details of the error. I don't think you're bricked yet
Click to expand...
Click to collapse
Thanks for your help. I get Error 260:
The update utility cannot connect to your pda. please check usb is connected. click exit to quit.
When I try to run the upgrade alone in XP it starts at 1% then resets the bootloader.
Thanks,
Gilbert
k which upgrade are you running? still trying to get hard spl working, or running the Dopod WM6 upgrade?
*i've been having some troubles upgrading today too, with the WM6.. scary times ha*
racerx_ said:
k which upgrade are you running? still trying to get hard spl working, or running the Dopod WM6 upgrade?
*i've been having some troubles upgrading today too, with the WM6.. scary times ha*
Click to expand...
Click to collapse
I am trying to upgrade the
RUU_Trinity_DOPODASIA_WWE_3.00.707.17_6275_1.46.00.11_108_Ship but i also tried to reflash the 1.23 HTC rom with GPS to see if it would flash since my device is an HTC trinity and not dopod but the same thing keeps happening.
Try to flash PDAVIET version, my came to life doing this
have you tried to flash any other ROM? I was stuck with the same thing, but managed to flash a cooked ROM..
what's your bootloader showing?
if you fail to flash any other ROM, i think you need to try the stack overfow exploit posted here.. http://forum.xda-developers.com/showthread.php?t=308691&highlight=error+206
it's a bit technical, but i think it's your best bet if all else fails.. Pof might be able to help you over there
No matter what i do, what rom i try to flash i get the same damn error message: Error 260 - Connection!!! I am connected so I don't what is wrong with it. I will try some more then decide to take a hammer and break it into 1000 peices.
Thanks.
racerx_ said:
have you tried to flash any other ROM? I was stuck with the same thing, but managed to flash a cooked ROM..
what's your bootloader showing?
if you fail to flash any other ROM, i think you need to try the stack overfow exploit posted here.. http://forum.xda-developers.com/showthread.php?t=308691&highlight=error+206
it's a bit technical, but i think it's your best bet if all else fails.. Pof might be able to help you over there
Click to expand...
Click to collapse
My bootloader is showing the following:
Trin100
IPL-0.50
Trin100
SPL-3.03.0000
Thanks for all your help.
hmmm... i'm not familiar with that SPL number... unless somehow that got halfway updated with the WM6 update.
I think you better head to that thread and try the stack exploit. Did you try loading a cooked ROM to see what happens?
that is it. i give up. i am not experienced in messing with codes. i am going to retire the device for good and use a regular phone. this is crap. thanks for ur help.
oh, that is the SPL version of the new ROM... i guess you weren't using hard spl when you tried to flash it?
ha, well don't give up too quick.. that's one expensive retired device you've got there.
Just keep cool and you should try to install an official Rom to downgrade this SPL !!
Gilbert said:
I will try some more then decide to take a hammer and break it into 1000 peices.
Thanks.
Click to expand...
Click to collapse
Help!
My bootloader is showing the following:
Trin100
IPL-1.00
Trin100
SPL-9.99.CP
When upgrading with the new released WM6 ROM, it keeps failing at 28%
Please help!
best bet for you, is load a different ROM now. Either cooked or official. That will get your device out of crash-proof spl bootloader.
Once the ROM is loaded, if you want to try the official wm6 again, run SSPL first and see if it'll work for you
p.s. i pm'd you my handphone number in case you've got trouble still..
Gilbert said:
My bootloader is showing the following:
Trin100
IPL-0.50
Trin100
SPL-3.03.0000
Thanks for all your help.
Click to expand...
Click to collapse
Hi Gilbert,
Im having exactly the same problem as you. Right now im in the middle of flashing it back down to WM5 (its working at the moment at 17%).
Hopefully after this i will be able to flash back to WM6 (Most probably will go back to AX3L for now).
Hope this helps you out (im quite stressed about it too!)
Edit: I have just finished flashing to Official WM5, now flashing back to AX3L WM6. It works!

HTC touch diamond

hey guys im new on the forum because i ****ed up my htc diamond i flashed it with a unsigned olinex 1.40? anyway the thing is my device starts up en then it says you need to set some settings but the first thing is to align the lcd screen i cant bypass that wtf is wrong with this device? did i installed it right?
HTC touch diamond NLD 1.37.00.00 --> 1.40(maybe)
its a MDA please help or else my father will kick my ass
i moved you question to diamond thread
you will get help faster here
hm
Umm i dont think you messed up device seeing how your device boots up as usual and no spl error showed up on the RGB screen. Umm and the alignment thing, is that the screen where it has the cross hairs on it? like the middle then the left bottom left and so on? well not sure if umm know this but ur suppose to tap the center (no offense intended) if it doesn't boot up, try doing a hard reset see if it helps, hard reset is done by, it tell you here, http://www.hardreset.eu/htc_touch_diamond_hard_reset_soft_reset_en.html if your still having problem getting past the alignment screen, you may want to try and reflash the rom for the device. (but first wait for someone else take on this) but before u do flash check see if you did install hardspl right, to do this you press, volume down then reset button to get into the spl mode thingy. :/ hope i was atleast some help
Original
Try the HTC website for a Original UPdated ROM and flash with that, if that goes well, then try and cooked ROM (if you dare) from this site..
But personaly Id reflash with something off the HTC website first
Kris
Well I don't think u bricked ur phone otherwise the phone won't even boot... anywayz I think u better follow anubis23's suggestion first try the Hard Reset and we can take frm there... cause i think all it needs is a gud Hard Reset also another reason cud be is ur touch screen cud be givin u problems but i guess it's too early to say i suggest u do the Hard Reset and post ur results....
Good Luck
djwarden said:
Try the HTC website for a Original UPdated ROM and flash with that, if that goes well, then try and cooked ROM (if you dare) from this site..
But personaly Id reflash with something off the HTC website first
Kris
Click to expand...
Click to collapse
It's not as easy as flashing the Original ROM frm HTC cause u'll need to take in a lot factors before doin tht like did he do HARD SPL if he did he will need to revert back to the Orginal SPL fer warranty reasons and then flash the Orginal ROM... It wud be best fer Hkayak to do a Hard Reset and post his results....
how to hard reset a diamond
hope this helps
http://www.hardreset.eu/htc_touch_diamond_hard_reset_soft_reset_en.html
whitefalcon said:
It's not as easy as flashing the Original ROM frm HTC cause u'll need to take in a lot factors before doin tht like did he do HARD SPL if he did he will need to revert back to the Orginal SPL fer warranty reasons and then flash the Orginal ROM... It wud be best fer Hkayak to do a Hard Reset and post his results....
Click to expand...
Click to collapse
Yeh good point as he didnt say he did HARD SPL i assumed he didnt do it...
to early for thinking for me.......
do you get the tri colour screen?
if so you'll lucky... the boot loader is still working... the rom/radio/.nbh is trashed though...
boot it up...
and take it to usb mode... there you can reflash a rom in windows... (active sync wont load of course... but as long as your in usb mode it'll be able to flash)
Sir, i have DIAMOND touch with unknown language. i want change to FRENCH or ENGLISH. i serached in forum iam confused. please any one help me...
DIAM100 64M
SPL-1.93.0000
MicroP-Diam (LED) v11
PSOC-Diam STAGE_PVT v0x32
R1.00.25.05
G52.29.25.12h
D193.00.00
chotadevil said:
Sir, i have DIAMOND touch with unknown language. i want change to FRENCH or ENGLISH. i serached in forum iam confused. please any one help me...
DIAM100 64M
SPL-1.93.0000
MicroP-Diam (LED) v11
PSOC-Diam STAGE_PVT v0x32
R1.00.25.05
G52.29.25.12h
D193.00.00
Click to expand...
Click to collapse
Unknown language ?? lol sounds like he stole it
hmm, what if you go to system properties and look?
djwarden said:
Unknown language ?? lol sounds like he stole it
Click to expand...
Click to collapse
hahahaha lol exactly it seems like it.... care to explain chotadevil....
i don't why members are making new new reply with bla bla bla bla bla
where is answer for my question? really i don't know this phone in which language. i go " "regionale innstillinger"
"engelsk (usa)
engesk (zimbabwe)
estisk
finsk
@ whitefalcon(name is good but sound is bad) and @djwarden (^%&*$#) confirm this is which language
no i dont get the bootloader screen it says that i need to set the new settings for the mda but i cant get pass the crosshairs how long does that take????
chotadevil said:
i don't why members are making new new reply with bla bla bla bla bla
where is answer for my question? really i don't know this phone in which language. i go " "regionale innstillinger"
"engelsk (usa)
engesk (zimbabwe)
estisk
finsk
@ whitefalcon(name is good but sound is bad) and @djwarden (^%&*$#) confirm this is which language
Click to expand...
Click to collapse
It's norwegian.
As for the device itself, how could you NOT know what lang it is in if you BOUGHT it?!
fishy fishy.
Then again, that's not our problem, but you might want to watch your attitude.
A.
hkayak said:
no i dont get the bootloader screen it says that i need to set the new settings for the mda but i cant get pass the crosshairs how long does that take????
Click to expand...
Click to collapse
1: do a hard reset
if that doesn't help
2: get into bootloader mode and flash an official/oem Diamond ROM. Don't forget to hard reset after the flash.
3: don't ask us how to do it, check out the xda-dev wiki. All the info you need is in there.
ok. that's way i get this phone in cheap price.
then no solution for changing langugae!
htc touch diamond
i have done a hard reset but i need to set the crosshair setting but i cant get pass that why?
not tray to be a wise guy, but i have heard this before...
did you try to align the screen? and tap where the + is with the stylus/pen ?

Dead HTC P3300?

Sorry my english.
When I was putting a new room and asked to reboot never took on. Appears on screen:
IPL 3.13.0001
SPL 1.11.0000
GDM 02.94.90
OS 3.13.0.0
What to do now? How do the bootloader?
READ BEFORE POSTING
All´s is in the wiki.
ark666 said:
READ BEFORE POSTING
All´s is in the wiki.
Click to expand...
Click to collapse
I don't found anything about this problem, i have also got a ARTE100 with IPL 3.13, and i can start it or charge it on power...
I don´t understand what you say. I need help.
ark666 said:
READ BEFORE POSTING
All´s is in the wiki.
Click to expand...
Click to collapse
AsusA5EB said:
I don´t understand what you say. I need help.
Click to expand...
Click to collapse
AsusA5EB, your ARTEMIS is dead, i've exactly the same problem since 3 weeks.
You can try, to enter in bootloader : http://wiki.xda-developers.com/index.php?pagename=Artemis_Resets
I think u should tell us what rom u flashed on your device in the first place.
Flash original rom to solve the issue, if not, u can use mtty to reset flash, and then install your original rom.
U guys already know that before flashing ANY rom besides your local CID, U MUST UNLOCK IT BY USING USPL.
Like i told u, all´s in the WIKI.
Hi there...
Do not worry your phone is not dead.
Read some things about USPL and than if it doesn't helps (and it won't, because I presume that you can't synchronize it with active sync), read something about MTTY and how to use it.
Be patient, read carefully and you'll make it.
By looking on your report from splash screen I can see that you have done USPL....but it went wrong.MTTY will solve your problem.
Spend some time reading and you'll do it.
Cheers
Z
zikizile said:
Hi there...
By looking on your report from splash screen I can see that you have done USPL....but it went wrong.
Click to expand...
Click to collapse
How can you tell USPL went wrong? I have the same IPL & SPL values in my device and everything looks good..
Ok, my phone is dead, the screen was break avec the power switch is dead....
ark666 said:
I think u should tell us what rom u flashed on your device in the first place.
Flash original rom to solve the issue, if not, u can use mtty to reset flash, and then install your original rom.
U guys already know that before flashing ANY rom besides your local CID, U MUST UNLOCK IT BY USING USPL.
Like i told u, all´s in the WIKI.
Click to expand...
Click to collapse
Hi,
Can you please tell me which ROM, RADIO do you use for ARTEMIS?
Thanks.

[TUT] HOW-TO restore Diamond to stock for warranty

Due to a hardware problem in my Diamond I needed to restore it to manufacturer default. I didn't find a guide to this and since I've done the research anyway I thought I'd put together this little tutorial as the information was somewhat scattered around the forum. I hope this guide will be of use for the community.
My phone was originally branded and sim-locked by 3. After I was through with it, it was SIM-unlocked, security unlocked and had HSPL, custom ROM and a radio ported from another device. The steps below is what I did to restore it to stock. All steps might not be neccessary for you. This procedure might also work for other devices than the Diamond, but of course you need other versions of SPL, ROM etc.
1. Backup everything on your phone to your computer - use activesync, PIMbackup etc and make a copy of your Internal Storage.
2. Make a hard reset (hold vol down + enter and soft reset) and chose to format moviNAND. This step is only neccessary if you want to wipe your Internal Storage before you send the device in for repair, but I recommend it.
3. Go to www.htc.com and download the latest stock ROM (includes stock radio and SPL). You find it under Support and you enter your s/n to get the correct stock ROM for your device, complete with branding for your operator. You can also find stock ROMS here: http://forum.xda-developers.com/showthread.php?t=471699
4. Flash the stock ROM. Now you have stock ROM and Radio on your device. Stock SPL will not be installed until you've replaced HSPL with an older stock SPL and flashed ROM again.
5. Get RUU-SSPL and stock SPL from HERE:
http://forum.xda-developers.com/showpost.php?p=2324829&postcount=39. I used the stock 1.93 SPL. Some instructions and info about restoring stock SPL is in the linked post by cmonex and due credit goes to her. I will repeat some of that info to keep this guide step-by-step. EDIT: Stock SPL 2.03 can be found here: http://forum.xda-developers.com/showpost.php?p=3359191&postcount=390
6. Put the .nbh file from the SPL you downloaded into the same folder as the extracted contents of RUU-SSPL-withoutNBH.zip and run the RUU. This flashes an old stock SPL.
7. Flash your stock ROM from step 3 again. This step is neccessary to get the correct stock SPL on your device, eg. the one that corresponds with the stock ROM you've downloaded in step 3. It was not installed in step 4, because then you still had HSPL. In step 6 you've installed a stock SPL and now the correct stock SPL will flash along with the stock ROM. After this step I got SPL 2.03 on my Diamond.
8. Remove the Security Unlock from your device using the instructions and Security Relocker by Olinex from this post by cmonex: http://forum.xda-developers.com/showpost.php?p=3299516&postcount=492
Now, my Diamond is still SIM-unlocked. I have not managed to find any info about how to restore the SIM-lock, but it is hopefully not neccessary for warranty. As far as I can tell, the unlock doesn't show anywhere, but of course all they need to do is to try a SIM-card from another operator...
If anyone has info about how to restore SIM-lock, then I'll update this guide with that info.
good job...
moderator make this "sticky"
3dward87 said:
good job...
moderator make this "sticky"
Click to expand...
Click to collapse
I second that, it contains links to stock ROMs, that'll hopefully stop a million topics about it lol.
This does not work for me.. However i have a problem. the touch screen of my device is not working.. so i can't get pass the allign screen part .. and for somereason the ruu won't connect to phone when it is at tha part so i can't install the spl.. the only way i can do that i through bootloader and it flashes fine but when i then look in bootloader to see the spl it still shows 1.40 olinex..
Da9L said:
This does not work for me.. However i have a problem. the touch screen of my device is not working.. so i can't get pass the allign screen part .. and for somereason the ruu won't connect to phone when it is at tha part so i can't install the spl.. the only way i can do that i through bootloader and it flashes fine but when i then look in bootloader to see the spl it still shows 1.40 olinex..
Click to expand...
Click to collapse
You're right, I tried it too. Flashing SPL through bootloader doesn't work.
You can try using JumpSPL instead, I've attached it in this post. I don't think JumpSPL will require any screen prompts on your Diamond. You can read instructions.txt in the zip, but it's just really the .bat file so you get an idea of what it's doing. Run the .bat, press enter at the prompts and run the RUU for your stock SPL instead of HSPL when asked. At your own risk, I have not tried this myself.
where can i read more information about jumpspl, how it works and everything?
eranyanay said:
where can i read more information about jumpspl, how it works and everything?
Click to expand...
Click to collapse
Look in the Xda-wiki, search and google, and not just in the Diamond section.
sticky please
this needs to be a sticky topic.
losdrivare said:
You're right, I tried it too. Flashing SPL through bootloader doesn't work.
You can try using JumpSPL instead, I've attached it in this post. I don't think JumpSPL will require any screen prompts on your Diamond. You can read instructions.txt in the zip, but it's just really the .bat file so you get an idea of what it's doing. Run the .bat, press enter at the prompts and run the RUU for your stock SPL instead of HSPL when asked. At your own risk, I have not tried this myself.
Click to expand...
Click to collapse
I have just tried it and it gets stuck where it should run the JumpSPL.exe on the device. After a few minutes it comes with an error:
"ERROR: CreateProcess failed with Errorcode = 30123
- UNKNOWNERROR: 0x000075ab"
This is not good I just think its wierd that because of a broken screen it is impossible for me to get the stock spl flashed back on.
Da9L said:
I have just tried it and it gets stuck where it should run the JumpSPL.exe on the device. After a few minutes it comes with an error:
"ERROR: CreateProcess failed with Errorcode = 30123
- UNKNOWNERROR: 0x000075ab"
This is not good I just think its wierd that because of a broken screen it is impossible for me to get the stock spl flashed back on.
Click to expand...
Click to collapse
Sorry to hear it and I'm afraid I'm out of ideas. After all, my little tutorial is primarily aimed at those whose Diamonds have working screens...
On another note, my Diamond came back from warranty repair and the repair shop had not noticed anything that would void my warranty. In the meantime I got myself a Topaz and now I've sold my Diamond, but I'll be checking this thread from time to time.
Hey thanks bro..!! I need to give mine for reparing..
I have a hardware problem with the reset button.. Do you think I should flash my diamond back to stock? (I don't think they'll check the software right?)
donsalari said:
Hey thanks bro..!! I need to give mine for reparing..
I have a hardware problem with the reset button.. Do you think I should flash my diamond back to stock? (I don't think they'll check the software right?)
Click to expand...
Click to collapse
I would restore it to stock anyway. Some workshops actually look for excuses/reasons why the warranty won't apply so I say you'd definitly be taking a risk if you didn't.
losdrivare said:
I would restore it to stock anyway. Some workshops actually look for excuses/reasons why the warranty won't apply so I say you'd definitly be taking a risk if you didn't.
Click to expand...
Click to collapse
Very true!!! Ok cool... Flashing back to stock!!
Thanks..
Damn.. Hmm anyway then i will have to try the risk and sending it in with hardspl on it.. ! I Hope they won't see it.
Da9L said:
Damn.. Hmm anyway then i will have to try the risk and sending it in with hardspl on it.. ! I Hope they won't see it.
Click to expand...
Click to collapse
Another idea: maybe you can find some a VNC program that also works the "other way" with windows mobile, so that you can get a window on your PC with the screen of your device?
Hi. I'm an orange user and i dont know what SPL i should use to send back to warranty!
DOes anyone can recommend it please?
My Orange ROM is RUU_Diamond_HTC_WWE_1.93.405.1_Radio_Signed_Diamon d_52.29.25.12_1.00.25.05_Ship
UPDATE - i flashed the new rom and i tried to put the original SPL, however it still showing 1.40 Olinex in the bootloader and it still says security unlocked.
Any help please...
Hi I m singapore user i dont know what is the original spl 1.23 ??? i 4get leh can u tell me
bro i try 1.23.000 that version are u sure this is offical stockspl
as i remember it shld be SSPL not SPL somemore when running the tri-boot colour is diffferent from the offical 1
1 . Press volume up restore factory default bla bla bla ..
2 . Press volume down restore factory default and format the internal storage
3 . Press any button to cancel
Where is 2 n 3 ??? gone oridi
herpez said:
Hi. I'm an orange user and i dont know what SPL i should use to send back to warranty!
DOes anyone can recommend it please?
My Orange ROM is RUU_Diamond_HTC_WWE_1.93.405.1_Radio_Signed_Diamon d_52.29.25.12_1.00.25.05_Ship
UPDATE - i flashed the new rom and i tried to put the original SPL, however it still showing 1.40 Olinex in the bootloader and it still says security unlocked.
Any help please...
Click to expand...
Click to collapse
k3nnyboiboi said:
Hi I m singapore user i dont know what is the original spl 1.23 ??? i 4get leh can u tell me
Click to expand...
Click to collapse
If you manage to install ANY stock SPL and then flash the correct ROM for your country and operator then you automatically get the correct SPL too, since stock ROMs include SPL. If you go to htc.com and type in your s/n then you automatically get the latest ROM for your device and operator.
k3nnyboiboi said:
bro i try 1.23.000 that version are u sure this is offical stockspl
as i remember it shld be SSPL not SPL somemore when running the tri-boot colour is diffferent from the offical 1
1 . Press volume up restore factory default bla bla bla ..
2 . Press volume down restore factory default and format the internal storage
3 . Press any button to cancel
Where is 2 n 3 ??? gone oridi
Click to expand...
Click to collapse
I only link to the SPLs provided by olipro and cmonex in the hard-SPL thread. If you need closer info about SPLs I suggest you ask there. I only tried to revert back to stock SPL 1.93 myself and it worked just like described in first post.
Thanks Op
Managed to restore it no problem, but took ages

Categories

Resources