Develop Bugs

Need to downgrade from WMIV Black 1.2 to Original DOPOD ROM

I need to downgrade my rom for warrany purposes (the OK key is stuck) But when I load up my Original ROM when my unt goes to the bootloader tingy, it disconnects from activesync and just well.. does noting.
Please help, anyone?
Thnaks

Execute SSPL and then run the RUU.
EDIT: Note that Hard-SPL (which I assume you have installed) will not protect you from failure because the original ROM has its own bootloader that it will put on your device, which is a good thing in terms of warranty, but a bad thing in terms of a power outage.

Original rom
Did you manage to do it and revert back/

look at this guide http://www.mrvanx.org/hermes_guide/

Yep, the guide will help you through doing this. It takes a slightly more time consuming approach but you are almost guaranteed not to permenantly brick your device doing it this way, as the last thing to be flashed is the radio, then the SPL.

Ive read the guide when i wanted to upgrade and its very helpful. Did'nt notice there was a segment on downgrading which i believe will be helpful as well. Thanks for your patience and answering, you guys are kind, for pointing me in that direction.

HArd SPL? Uh, no I didn't install that.. should I?
Trancecoder said:
Execute SSPL and then run the RUU.
EDIT: Note that Hard-SPL (which I assume you have installed) will not protect you from failure because the original ROM has its own bootloader that it will put on your device, which is a good thing in terms of warranty, but a bad thing in terms of a power outage.
Click to expand...
Click to collapse
HArd SPL? Uh, no I didn't install that.. should I?
Sorry for asking but what is an SSPL?

It's funny!!! If you don't know (yet) what is SSPL and did not (yet) installed HardSPL, Wow did you install a WM6 cooked ROM?

dcoelho said:
It's funny!!! If you don't know (yet) what is SSPL and did not (yet) installed HardSPL, Wow did you install a WM6 cooked ROM?
Click to expand...
Click to collapse
Yes, I installed a WM VI 2.0. Anyone please tell me what is an SSPL?

@ Deadman
I would suggest you start reading here: http://forum.xda-developers.com/showthread.php?t=293651
Then go to the wiki:
http://wiki.xda-developers.com/index.php?pagename=HTC_Hermes
and do a lot more reading before you really do something even more seriously seriously nasty to your phone.
You should have installed Olipro's Hard-SPL before any kind of rom upgrades.
There is also a complete guide on the wiki to unbricking your phone.

Got it, thanks.
Thanks
chrisjasper said:
@ Deadman
I would suggest you start reading here: http://forum.xda-developers.com/showthread.php?t=293651
Then go to the wiki:
http://wiki.xda-developers.com/index.php?pagename=HTC_Hermes
and do a lot more reading before you really do something even more seriously seriously nasty to your phone.
You should have installed Olipro's Hard-SPL before any kind of rom upgrades.
There is also a complete guide on the wiki to unbricking your phone.[/QUOT
Click to expand...
Click to collapse

Thanks
I would like to thank those who helped me. I downgraded it using SSPL then RUU. Thanks

Stuck at 28% help needed

Stuck at 28% of upgrade
phone is showing 4 colors and does nothing
PLEASE PROVIDE LINK TO BE SAVED
LINKS AND INFO WHAT TO DO IN DETAIL
I AM NOT A COMPUTER GUY

flash official rom back. Then download this rom
http://rapidshare.com/files/42141641/Wm6_Official.zip
and flash that one,

link for official rom ?
i remind you the phone is at the 4 colors mode

this page has all official roms ever made for trinity
http://wiki.xda-developers.com/index.php?pagename=Trinity_Upgrades

pkaza said:
link for official rom ?
i remind you the phone is at the 4 colors mode
Click to expand...
Click to collapse
Don't panic, the phone is not dead. You will get it fixed. Just follow the instructions given, there is a solution.

updated with official rom
hardspl does nothing
other way
?

Help me too!!! I don't even have an official ROM for my Orange m700

ward777 said:
Help me too!!! I don't even have an official ROM for my Orange m700
Click to expand...
Click to collapse
You could try this fix http://forum.xda-developers.com/showthread.php?t=316313&page=5

I don't think so. My Hard-SPL was overwritten and now has the 3.0 version and not SPL version 9.99.

9.99 is NOT Hard-SPL, it's Des's Crashproof spl which is not even trying to prevent itself from being overwritten.

OliPro?
Hello
What about OliPro SPL-1.20.Olipro with IPL-0.5
Can it also be overwritten or wich hard spl do I need first to flash?
Roman

don't worry , simply follow the instruction and reflash it again with the new rom , then it will pass through the 28% ...

Shadowmite said:
9.99 is NOT Hard-SPL, it's Des's Crashproof spl which is not even trying to prevent itself from being overwritten.
Click to expand...
Click to collapse
I know that
But I did have Hard-SPL and now it's gone so it will get overwritten when installing this ROM as well

tony800708 said:
don't worry , simply follow the instruction and reflash it again with the new rom , then it will pass through the 28% ...
Click to expand...
Click to collapse
What instructions?

ward777 said:
What instructions?
Click to expand...
Click to collapse
I guess you're in a pickle. There must be a way around not having an official Orange rom. Have you tried the SD card method from an Orange rom dump? Otherwise, the rom cookers should be able to come up with something. With all of these people trying these roms certainly you must not be the only one with an Orange phone. Good luck .

Hi Guys,
I am also stuck @ bootloader. I have the original rom, but how do I flash this back? It keeps on telling me that it cannot detect the phone. What can I do? Thank you!

You can flash the spl from the bootloader via mtty, but that's not something Ive seen clear instructions on how to do... you might want to log into #xda-devs in freenode IRC and get stepped through it.
If you're stuck at the bootloader, just try running the hard-spl flash right from there...

ward777 said:
I know that
But I did have Hard-SPL and now it's gone so it will get overwritten when installing this ROM as well
Click to expand...
Click to collapse
Yeah, I thought deleting 'SPL.nbh' would prevent the RUU from installing the new SPL but the Hard-SPL got overwritten on flashing.
Kris

there are 2 spl entries in the release... spl.nb and spl.nbh... you have to remove both. also I'd remove the ipl.nb...

These are the files inside the exe:
EnterBootloader.exe
ErrorBattery.fig
ErrorUSB.fig
ModelID.fig
rapitool.exe
README.doc
ROMUpdateUtility.cfg
ROMUpdateUtility.exe
RUUGetInfo.exe
RUUResource.dll
RUU_signed.nbh
SPL.nbh
I suppose you meant to remove the .nb entries inside RUU_signed.nbh
Kris

Help: Can't flash anything any more

Hallo everbody.
I'd really be glad, if you could help my with my problem:
I currently have bepe's german WM6 ROM v. 0.5 installed on my P3600. Now, the problem is, that I cannot flash anything anymore. When I start any rom update, the device enters boot loader, the progress bar gradually counts to 100% (a little faster, than I remember it doing before). At 100% the device turns off, but doesn't reboot itself. The rom update utility reports a success. When I then restart the device, everything is as before, without any changes.
My installed Hard SPL is SPL-9.99.CP. I tried to flash Olipro's new SPL without any luck. The SPL remains SPL-9.99.CP.
I don't know what to do any more...

have you installed Hard SPL by Oli 1.30????
if yes, downgrade to 1.20 version

psxsnake said:
have you installed Hard SPL by Oli 1.30????
if yes, downgrade to 1.20 version
Click to expand...
Click to collapse
Problem is, I have SPL-9.99.CP installed. It seems, that I even cannot flash to another SPL any more. I just tried to flash Oli 1.30 without any luck.

paranoid2007 said:
Problem is, I have SPL-9.99.CP installed. It seems, that I even cannot flash to another SPL any more. I just tried to flash Oli 1.30 without any luck.
Click to expand...
Click to collapse
SPL 9.99.CP will show with all HARD-SPLs I believe. Try to Flash HARD SPL 1.2 - and then try flashing again.
Lots of people could not flash anything with HARD SPL 1.3 flashed.

nealed said:
SPL 9.99.CP will show with all HARD-SPLs I believe. Try to Flash HARD SPL 1.2 - and then try flashing again.
Lots of people could not flash anything with HARD SPL 1.3 flashed.
Click to expand...
Click to collapse
Could you point me to SPL v. 1.2? I can't find it via the forum search.

nealed said:
SPL 9.99.CP will show with all HARD-SPLs I believe.
Click to expand...
Click to collapse
No you are wrong! SPL 9.99.CP is DES HARD-SPL and CP mean CrashProof.
IPL x.x.50xx is show with every HARD-SPL.
SPL 9.99.CP is okay! Have you tried to flash a original WM5 Rom?

sammy_deluxe said:
No you are wrong! SPL 9.99.CP is DES HARD-SPL and CP mean CrashProof.
IPL x.x.50xx is show with every HARD-SPL.
SPL 9.99.CP is okay! Have you tried to flash a original WM5 Rom?
Click to expand...
Click to collapse
No. If it might help, I'll try. Can you point me to where I can get an original german WM5 Rom?

Ok, found the original ROM Update from the HTC site. Flashed it. This time the device rebooted by itself. Result: I am still stuck with the bepe ROM 0.5. Updating did nothing!

paranoid2007 said:
Ok, found the original ROM Update from the HTC site. Flashed it. This time the device rebooted by itself. Result: I am still stuck with the bepe ROM 0.5. Updating did nothing!
Click to expand...
Click to collapse
try this way! http://wiki.xda-developers.com/index.php?pagename=Trinity_SDCardFlashing

sammy_deluxe said:
try this way! http://wiki.xda-developers.com/index.php?pagename=Trinity_SDCardFlashing
Click to expand...
Click to collapse
Doesn't work. Whenever I try to start Hard SPL, the bootloader shows up for about 5 seconds. Then the screen slowly starts fading to dark grey, so that I can't read anything on the display. Then nothing more happens.

try goin into the bootloader screen on the device first rather that using the update tool first.. this should work

steveecourt said:
try goin into the bootloader screen on the device first rather that using the update tool first.. this should work
Click to expand...
Click to collapse
OMG this worked! Thanks a million. Strangely enough, I tried it this morning without luck.

I also have SPL 9.99 CP and if you put a rom on the flash card it just seems to ignore the file and goes backk into bootloader

steveecourt said:
I also have SPL 9.99 CP and if you put a rom on the flash card it just seems to ignore the file and goes backk into bootloader
Click to expand...
Click to collapse
I have the same SPL but I had never flashed a rom from Flash card.. Could you explain more in the deep how it works? did it once with older Rom's?

Is it bricked?

Hello,
My model ID disappeared from my phone and now I cannot upload anything to it anymore.. It happened while updating to spl 1.40 Olinex... Does anyone have an idea how to upload a Rom without the need of a Device ID? The spl has the right number (I can see that in the Bootloader screen)...
Help?

xanh said:
Hello,
My model ID disappeared from my phone and now I cannot upload anything to it anymore.. It happened while updating to spl 1.40 Olinex... Does anyone have an idea how to upload a Rom without the need of a Device ID? The spl has the right number (I can see that in the Bootloader screen)...
Help?
Click to expand...
Click to collapse
This has happen to my phone as well can you go to bootloader mode and write down all the details here, we might have to contact ccmonex/olinex if its the same which happpen to me,

xanh said:
Hello,
My model ID disappeared from my phone and now I cannot upload anything to it anymore.. It happened while updating to spl 1.40 Olinex... Does anyone have an idea how to upload a Rom without the need of a Device ID? The spl has the right number (I can see that in the Bootloader screen)...
Help?
Click to expand...
Click to collapse
hey. dutty showed me this thread drop me a PM and we can try and fix this.
basically we'll first try to write your modelid back, if that doesn't work, then the last option is flash an SPL that ignores modelid.

cmonex said:
hey. dutty showed me this thread drop me a PM and we can try and fix this.
basically we'll first try to write your modelid back, if that doesn't work, then the last option is flash an SPL that ignores modelid.
Click to expand...
Click to collapse
thanks for responding so fast hope it isnt that bad like it was mines

Thanks for your quick reply's..
Here's my info:
MFG 64M
SPL-1.40.OliNex
MicroP-Diam (LED) v11
PSOC-Diam STAGE_PVT v0x30
If I take out the battery I can see DIAM100 in the case...

xanh said:
Thanks for your quick reply's..
Here's my info:
MFG 64M
SPL-1.40.OliNex
MicroP-Diam (LED) v11
PSOC-Diam STAGE_PVT v0x30
If I take out the battery I can see DIAM100 in the case...
Click to expand...
Click to collapse
just pm cmnonex and she will guide you

Another problem is with mtty..
When I start up the program and my phone in boot loader, then mtty crashes immediately when I press a button.. If I disconnect usb and reconnect it again I can type stuff in, but I can type in text without anything happening..
I'm starting to give up on this phone. Maybe I should start seeing it as a expensive pda..

i have the same issue .. me phone is freez then i have to remove battery out .. and restart again ... BUT ... everything is gone ... i cannot doing anything with it ....doesnt matter what kind the rom i upgrade .. still came bootloader ONLY ... i have read many thread about BRICK ... but nothing could help ......please any advise .... HELPP..... please

First of all :
Relax
Got a new diamond today and had the same issues.
What Windows OS are you using ? Do you use WDMC or Activesync ?
What is the driver version of the installed HTC Sync ?
As for mtty :
Next version of QMAT will be fine and will be much more stable than mtty.
As for bootloader :
1. Are you able to connect to mtty, and does it respond to command
"info 2" ?
If yes, fixing it should be no problem.
Contact cmonex, she will be able to help you.
If she isn't able, I and cmonex will figure out what to do next
Cya,
Viper BJK

viperbjk said:
First of all :
Relax
Got a new diamond today and had the same issues.
What Windows OS are you using ? Do you use WDMC or Activesync ?
What is the driver version of the installed HTC Sync ?
As for mtty :
Next version of QMAT will be fine and will be much more stable than mtty.
As for bootloader :
1. Are you able to connect to mtty, and does it respond to command
"info 2" ?
If yes, fixing it should be no problem.
Contact cmonex, she will be able to help you.
If she isn't able, I and cmonex will figure out what to do next
Cya,
Viper BJK
Click to expand...
Click to collapse
Thanks for quick reply VIPER ... my phone run well until i remove the battery ... everything turn out bad ....i use stock rom with is HK version 1.93.871.1
seem to me usb working fine... i can upgrade it ...but ... when is done ...only have bootloader ...First come with ::: DIAMOND TOUCH :: then black out ..when i press power button again .. coming only bootloader screen, no matter what rom i try ... still in bootloader mode.........please help .......

was a double message

viperbjk said:
First of all :
Relax
Got a new diamond today and had the same issues.
What Windows OS are you using ? Do you use WDMC or Activesync ?
What is the driver version of the installed HTC Sync ?
As for mtty :
Next version of QMAT will be fine and will be much more stable than mtty.
As for bootloader :
1. Are you able to connect to mtty, and does it respond to command
"info 2" ?
If yes, fixing it should be no problem.
Contact cmonex, she will be able to help you.
If she isn't able, I and cmonex will figure out what to do next
Cya,
Viper BJK
Click to expand...
Click to collapse
Hi Viper,
Thanks for your reply,
Unfortunately qmat crashes too when I try to send it a command... The version I use here is v395..
I'm using Activesync 4.5.. But this has been disabled...
After a while windows tells me that it finds an unknown device when in bootloader..
The OS is still working and is a HK version 1.93.871.1 as well..
Although I don't know if the OS part is fully ok, since after a hard reset the extra programs get installed and the phone crashes on installing opera...
Could it be that the bootloader itself is not functioning properly making all the tools crash?
My idea is to change the id of the phone to be able to upload a new SPL, and upload a original ROM... At least it should work again then... But I've been trying for more than a week now..
Thanks..

Xanh, which spl is now installed on your device ?
If it is the Hard Spl, try manualspl to reflash spl again. I guess SPL is broken.
Normally, you don't need to change the ID for that.
Changing the ID is only needed when flashing a ROM other than your
original one.
k3vin168 : Also try to reflash SPL. If you've done that and it did work, please contact me via PM. Then either your nand is bad or you need to change the bootmode.
Cya,
Viper BJK

SPL is 1.40.OliNex, but I don't need to change the ID, but it's missing since failing installing 1.40.OliNex SPL.. How does this manual SPL upload work?
No matter which update I try, it will always say that Device ID is wrong... I think NAND is somehow bad, since that's where the device ID is stored right?

xanh,
Could be that nand is bad. There are two regions where the device id is stored.
Memory and NAND. But both can be fixed using Hard SPL (MFG).
PM me, I'll try to help you out of your misery.

k3vin168 said:
Thanks for quick reply VIPER ... my phone run well until i remove the battery ... everything turn out bad ....i use stock rom with is HK version 1.93.871.1
seem to me usb working fine... i can upgrade it ...but ... when is done ...only have bootloader ...First come with ::: DIAMOND TOUCH :: then black out ..when i press power button again .. coming only bootloader screen, no matter what rom i try ... still in bootloader mode.........please help .......
Click to expand...
Click to collapse
Any progress on this one ?
If not, please PM me

xanh said:
SPL is 1.40.OliNex, but I don't need to change the ID, but it's missing since failing installing 1.40.OliNex SPL.. How does this manual SPL upload work?
No matter which update I try, it will always say that Device ID is wrong... I think NAND is somehow bad, since that's where the device ID is stored right?
Click to expand...
Click to collapse
he meant SSPL-Manual.exe from the hardspl thread, but I don't think that would fix mtty.
anyway, have you got my PM. if mtty is hopeless, the other route is what you need (flash SPL without modelid check via special no checking SSPL). I sent you all links and instructions.
(I'd rather not make the files public or all the noobs will start flashing random devices' roms.)
EDIT: I assume your OS is able to boot, but if not, then you need a different set of files, let me know

viperbjk said:
xanh,
Could be that nand is bad. There are two regions where the device id is stored.
Memory and NAND. But both can be fixed using Hard SPL (MFG).
PM me, I'll try to help you out of your misery.
Click to expand...
Click to collapse
for duttythroy, we could not write the modelid back to nand for some reason. lnb said success, then it was still not there in the flash when reading it out afterwards. so I just had him flash a "special" spl

k3vin168 said:
i have the same issue .. me phone is freez then i have to remove battery out .. and restart again ... BUT ... everything is gone ... i cannot doing anything with it ....doesnt matter what kind the rom i upgrade .. still came bootloader ONLY ... i have read many thread about BRICK ... but nothing could help ......please any advise .... HELPP..... please
Click to expand...
Click to collapse
what is your SPL version in tricolour screen?

cmonex said:
what is your SPL version in tricolour screen?
Click to expand...
Click to collapse
i use same as other 1.40 i try all VIPER try to help me out ... but all not working ....just stuck in splash screen ..i try all kind of ROM but still stuck ...i can i do ?? please help

[TUT] HOW-TO restore Diamond to stock for warranty

Due to a hardware problem in my Diamond I needed to restore it to manufacturer default. I didn't find a guide to this and since I've done the research anyway I thought I'd put together this little tutorial as the information was somewhat scattered around the forum. I hope this guide will be of use for the community.
My phone was originally branded and sim-locked by 3. After I was through with it, it was SIM-unlocked, security unlocked and had HSPL, custom ROM and a radio ported from another device. The steps below is what I did to restore it to stock. All steps might not be neccessary for you. This procedure might also work for other devices than the Diamond, but of course you need other versions of SPL, ROM etc.
1. Backup everything on your phone to your computer - use activesync, PIMbackup etc and make a copy of your Internal Storage.
2. Make a hard reset (hold vol down + enter and soft reset) and chose to format moviNAND. This step is only neccessary if you want to wipe your Internal Storage before you send the device in for repair, but I recommend it.
3. Go to www.htc.com and download the latest stock ROM (includes stock radio and SPL). You find it under Support and you enter your s/n to get the correct stock ROM for your device, complete with branding for your operator. You can also find stock ROMS here: http://forum.xda-developers.com/showthread.php?t=471699
4. Flash the stock ROM. Now you have stock ROM and Radio on your device. Stock SPL will not be installed until you've replaced HSPL with an older stock SPL and flashed ROM again.
5. Get RUU-SSPL and stock SPL from HERE:
http://forum.xda-developers.com/showpost.php?p=2324829&postcount=39. I used the stock 1.93 SPL. Some instructions and info about restoring stock SPL is in the linked post by cmonex and due credit goes to her. I will repeat some of that info to keep this guide step-by-step. EDIT: Stock SPL 2.03 can be found here: http://forum.xda-developers.com/showpost.php?p=3359191&postcount=390
6. Put the .nbh file from the SPL you downloaded into the same folder as the extracted contents of RUU-SSPL-withoutNBH.zip and run the RUU. This flashes an old stock SPL.
7. Flash your stock ROM from step 3 again. This step is neccessary to get the correct stock SPL on your device, eg. the one that corresponds with the stock ROM you've downloaded in step 3. It was not installed in step 4, because then you still had HSPL. In step 6 you've installed a stock SPL and now the correct stock SPL will flash along with the stock ROM. After this step I got SPL 2.03 on my Diamond.
8. Remove the Security Unlock from your device using the instructions and Security Relocker by Olinex from this post by cmonex: http://forum.xda-developers.com/showpost.php?p=3299516&postcount=492
Now, my Diamond is still SIM-unlocked. I have not managed to find any info about how to restore the SIM-lock, but it is hopefully not neccessary for warranty. As far as I can tell, the unlock doesn't show anywhere, but of course all they need to do is to try a SIM-card from another operator...
If anyone has info about how to restore SIM-lock, then I'll update this guide with that info.

good job...
moderator make this "sticky"

3dward87 said:
good job...
moderator make this "sticky"
Click to expand...
Click to collapse
I second that, it contains links to stock ROMs, that'll hopefully stop a million topics about it lol.

This does not work for me.. However i have a problem. the touch screen of my device is not working.. so i can't get pass the allign screen part .. and for somereason the ruu won't connect to phone when it is at tha part so i can't install the spl.. the only way i can do that i through bootloader and it flashes fine but when i then look in bootloader to see the spl it still shows 1.40 olinex..

Da9L said:
This does not work for me.. However i have a problem. the touch screen of my device is not working.. so i can't get pass the allign screen part .. and for somereason the ruu won't connect to phone when it is at tha part so i can't install the spl.. the only way i can do that i through bootloader and it flashes fine but when i then look in bootloader to see the spl it still shows 1.40 olinex..
Click to expand...
Click to collapse
You're right, I tried it too. Flashing SPL through bootloader doesn't work.
You can try using JumpSPL instead, I've attached it in this post. I don't think JumpSPL will require any screen prompts on your Diamond. You can read instructions.txt in the zip, but it's just really the .bat file so you get an idea of what it's doing. Run the .bat, press enter at the prompts and run the RUU for your stock SPL instead of HSPL when asked. At your own risk, I have not tried this myself.

where can i read more information about jumpspl, how it works and everything?

eranyanay said:
where can i read more information about jumpspl, how it works and everything?
Click to expand...
Click to collapse
Look in the Xda-wiki, search and google, and not just in the Diamond section.

sticky please
this needs to be a sticky topic.

losdrivare said:
You're right, I tried it too. Flashing SPL through bootloader doesn't work.
You can try using JumpSPL instead, I've attached it in this post. I don't think JumpSPL will require any screen prompts on your Diamond. You can read instructions.txt in the zip, but it's just really the .bat file so you get an idea of what it's doing. Run the .bat, press enter at the prompts and run the RUU for your stock SPL instead of HSPL when asked. At your own risk, I have not tried this myself.
Click to expand...
Click to collapse
I have just tried it and it gets stuck where it should run the JumpSPL.exe on the device. After a few minutes it comes with an error:
"ERROR: CreateProcess failed with Errorcode = 30123
- UNKNOWNERROR: 0x000075ab"
This is not good I just think its wierd that because of a broken screen it is impossible for me to get the stock spl flashed back on.

Da9L said:
I have just tried it and it gets stuck where it should run the JumpSPL.exe on the device. After a few minutes it comes with an error:
"ERROR: CreateProcess failed with Errorcode = 30123
- UNKNOWNERROR: 0x000075ab"
This is not good I just think its wierd that because of a broken screen it is impossible for me to get the stock spl flashed back on.
Click to expand...
Click to collapse
Sorry to hear it and I'm afraid I'm out of ideas. After all, my little tutorial is primarily aimed at those whose Diamonds have working screens...
On another note, my Diamond came back from warranty repair and the repair shop had not noticed anything that would void my warranty. In the meantime I got myself a Topaz and now I've sold my Diamond, but I'll be checking this thread from time to time.

Hey thanks bro..!! I need to give mine for reparing..
I have a hardware problem with the reset button.. Do you think I should flash my diamond back to stock? (I don't think they'll check the software right?)

donsalari said:
Hey thanks bro..!! I need to give mine for reparing..
I have a hardware problem with the reset button.. Do you think I should flash my diamond back to stock? (I don't think they'll check the software right?)
Click to expand...
Click to collapse
I would restore it to stock anyway. Some workshops actually look for excuses/reasons why the warranty won't apply so I say you'd definitly be taking a risk if you didn't.

losdrivare said:
I would restore it to stock anyway. Some workshops actually look for excuses/reasons why the warranty won't apply so I say you'd definitly be taking a risk if you didn't.
Click to expand...
Click to collapse
Very true!!! Ok cool... Flashing back to stock!!
Thanks..

Damn.. Hmm anyway then i will have to try the risk and sending it in with hardspl on it.. ! I Hope they won't see it.

Da9L said:
Damn.. Hmm anyway then i will have to try the risk and sending it in with hardspl on it.. ! I Hope they won't see it.
Click to expand...
Click to collapse
Another idea: maybe you can find some a VNC program that also works the "other way" with windows mobile, so that you can get a window on your PC with the screen of your device?

Hi. I'm an orange user and i dont know what SPL i should use to send back to warranty!
DOes anyone can recommend it please?
My Orange ROM is RUU_Diamond_HTC_WWE_1.93.405.1_Radio_Signed_Diamon d_52.29.25.12_1.00.25.05_Ship
UPDATE - i flashed the new rom and i tried to put the original SPL, however it still showing 1.40 Olinex in the bootloader and it still says security unlocked.
Any help please...

Hi I m singapore user i dont know what is the original spl 1.23 ??? i 4get leh can u tell me

bro i try 1.23.000 that version are u sure this is offical stockspl
as i remember it shld be SSPL not SPL somemore when running the tri-boot colour is diffferent from the offical 1
1 . Press volume up restore factory default bla bla bla ..
2 . Press volume down restore factory default and format the internal storage
3 . Press any button to cancel
Where is 2 n 3 ??? gone oridi

herpez said:
Hi. I'm an orange user and i dont know what SPL i should use to send back to warranty!
DOes anyone can recommend it please?
My Orange ROM is RUU_Diamond_HTC_WWE_1.93.405.1_Radio_Signed_Diamon d_52.29.25.12_1.00.25.05_Ship
UPDATE - i flashed the new rom and i tried to put the original SPL, however it still showing 1.40 Olinex in the bootloader and it still says security unlocked.
Any help please...
Click to expand...
Click to collapse
k3nnyboiboi said:
Hi I m singapore user i dont know what is the original spl 1.23 ??? i 4get leh can u tell me
Click to expand...
Click to collapse
If you manage to install ANY stock SPL and then flash the correct ROM for your country and operator then you automatically get the correct SPL too, since stock ROMs include SPL. If you go to htc.com and type in your s/n then you automatically get the latest ROM for your device and operator.
k3nnyboiboi said:
bro i try 1.23.000 that version are u sure this is offical stockspl
as i remember it shld be SSPL not SPL somemore when running the tri-boot colour is diffferent from the offical 1
1 . Press volume up restore factory default bla bla bla ..
2 . Press volume down restore factory default and format the internal storage
3 . Press any button to cancel
Where is 2 n 3 ??? gone oridi
Click to expand...
Click to collapse
I only link to the SPLs provided by olipro and cmonex in the hard-SPL thread. If you need closer info about SPLs I suggest you ask there. I only tried to revert back to stock SPL 1.93 myself and it worked just like described in first post.

Thanks Op
Managed to restore it no problem, but took ages