hello, I have a problem with my SPV M650, I change the rom, my phone doesn't working and I cann't connect my phone to pc. I cann't change the rom, I have tested on multiple computers (xp and vista), but it's the same thing.
Do you have a solution?
no solution to conected my phone
On Vista - You must uncheck "Enable advanced network functionality" in "USB to PC".
Related
I tried to flash my universal and the process failled, error ...
So, I did a hard reset, and always, my universal start in bootloader mode.
What Can I do?
When i connect it to the pc, I can see on the pda USB and 0.60.
I try to use mtty116.exe, but USB doesn't appears on the list.
my pda is dead???
Please help.
I too am in this situation. Should this work with Vista, or must it be XP only? I have unchecked the 'Allow USB connections' option in WMDC under Vista and PC plays tune to say connected but device centre doesn't show device as recognisd. Mtty doesn't have the USB option under the Port drop down menu. many thanks, Paul.
Hi to everybody!!!
I have used qtek 9000 with usb cabel,but without cd-software, i installd Microsoft acitve sync on my pc, but i cant connect gtek via USB mini cabel with pc - say: "ActiveSync cannot connect to the Windows mobile powered device"
Pls, where can i download cd software for qtek9000 or some driver???
Thnks to all,
hope this will help!!
thats a "working" active sync installation from my pc!
unrar and replace the files on your AS installation folder!
hope this will help you!!
here i comes!
This driver isnt for modem usb
pinkfluid said:
Hi to everybody!!!
I have used qtek 9000 with usb cabel,but without cd-software, i installd Microsoft acitve sync on my pc, but i cant connect gtek via USB mini cabel with pc - say: "ActiveSync cannot connect to the Windows mobile powered device"
Pls, where can i download cd software for qtek9000 or some driver???
Thnks to all,
Click to expand...
Click to collapse
Do you have any firewall installed? Have you run the Activesync troubleshooter? Atlast go to your device--> settings-->Connections-->USB to PC--> uncheck the Unable advanced network functionality
Hi, anyone got a w800 windows mobile?
i just got one off ebay.
it seems to work ok but i cant get it to connect to my pc.
I tried to use activesync but vista uses windows media devicecentre, I installed it then connected the w800 by usb cable, vista detected it and installed a driver for an UNKNOWN DEVICE. when I opened windows device centre it says "not connected".
i tryed to use vista s device sync and it said there is no devices to sync to?? even though the w800 is connected via cable...
anu idea,s what i,m doing wrong?
(apart from using a cect)..lol
In vista s device manager it says " windows based device" but device cant operate because of ( code 10) when I try check for solution it says cant load device driver.
hi
i have a diamond that when i connect to the USB cable ,it ask me normaly to chose betwen Activesync and mass storage but whatever i chose nothing happens on my pc and diamond itself.
my pc and my cable are ok because i can sync my friends diomond noramly.
does my diamond have a hardware problem?
adempozhari said:
hi
i have a diamond that when i connect to the USB cable ,it ask me normaly to chose betwen Activesync and mass storage but whatever i chose nothing happens on my pc and diamond itself.
my pc and my cable are ok because i can sync my friends diomond noramly.
does my diamond have a hardware problem?
Click to expand...
Click to collapse
Depending on whether you are using Vista or Xp.
Try this: Go to Start>Settings>Connections>USB to PC
> if there is a check mark by "Enable faster data sych.......Remove and see if this fixes your problem.
Secondly, if you flashed your ROM then make sure you remove the previous Device Partnership in your Activesync settings and make a NEW PARTNERSHIP.
Hope this helps!
i have the same problem i connect my phonr to my pc but it wont establisch a activesync connection
I have also the same problem.
When i connect mij Diamond richt below on mij PC sreen see I the message PC can't reconize mij Diamond (tested on more PC's with differnt cables).
If had someone the solution please mail me !
- Diamond with Hard-SPL Olinex 1.93 and the Dutch ROM v2.03.
hi,
i think my diamond has a hardware problem...because it ask me if i want to use activesync or storage when i plug the charger....
Hello
If you have problem to connect MDA Compact III, P3300, Artemis to Vista WMDC.
Just click on you PPC
Start > Settings > Connections > USB to PC
and Uncheck "Enable advanced network functionality"
That's all, no need to reinstall drivers, no SP1, no soft and hard reset.
PLEASE MAKE THIS STICKY, MANY PEOPLES HAVE PROBLEM WITH THIS
Thank you
thanx so much for the info...i fried my brain trying to connect it but i never thought to uncheck that damn thing....
i can not
I´ve already done this but i am not able to connect my p3300 to the wmdc.
I also do not find the drivers
could you help me?
I am not able to find that "USB to PC" icon in settings->connections menu. Or anywhere else. Maybe because I have a cooked ROM (Tom_B&B_v5.0_with_cube).
BTW I'm running Windows 7 and can't connect the device to pc. I tried WMDC but it keeps saying that my device is not connected.. So i thought that the reason might be this "advanced connectivity".
Thx in advance for some response
Well I've already found it - I'm a dumbass It wasn't in connections but in system..
Now it's time to test it.
Well even if I turned it off there is still no luck connecting it. Even in device manager there is no mobile devices tree. I have a cooked ROM so maybe this causes the problem?