My universal is blocked in bootloader mode!! - JASJAR, XDA Exec, MDA Pro Software Upgrading

I tried to flash my universal and the process failled, error ...
So, I did a hard reset, and always, my universal start in bootloader mode.
What Can I do?
When i connect it to the pc, I can see on the pda USB and 0.60.
I try to use mtty116.exe, but USB doesn't appears on the list.
my pda is dead???
Please help.

I too am in this situation. Should this work with Vista, or must it be XP only? I have unchecked the 'Allow USB connections' option in WMDC under Vista and PC plays tune to say connected but device centre doesn't show device as recognisd. Mtty doesn't have the USB option under the Port drop down menu. many thanks, Paul.

Related

Stucked to "Serial" bootloader mode

Hi all,
I was trying to upgrade my Qtek9000 with an official ROM Updater, but my device went immediately into the Serial bootloader mode and I've not been able to do nothing to run out from this mode...
I've tryied the solutions suggested in http://forum.xda-developers.com/showthread.php?t=290234 without any luck...
The problem is that neither Mtty nor the UNI_exitbootloader tool are able to connect to USB.
I'm using no usb hub, I'm running on a Dell Precision M90 notebook, I've disabled USB connection in Activesync (4.2.0) and also tryied with a pc without activesync installed.
Any idea?
Thanks
Paolo
Are you on XP or Vista, and what version of AS/WMDC do you have?
Hi,
I'm running Xp, ActveSync is 4.2.0, don't know what WMDC is sorry, can you please explain?
Don't worry about WMDC - it's only relevant if you have Vista.
Are you using the proper cable that came with the Universal? Some cables don't have all the pins wired. That (or a broken USB port) would explain why your Universal isn't going to USB mode when you plug in the USB cable. Have you looked carefully to see if it changes from saying "Serial" to "USB" at the top of the Bootloader screen when you plug in the cable?
If it does change to "USB", I would try upgrading to ActiveSync 4.5 - go to http://www.microsoft.com/windowsmobile/activesync/activesync45.mspx
Make sure you disable USB Connnections in the Connection settings before plugging in your Universal. Then try flashing the CE ROM again.
Good luck
BTW did you try doing a hard reset to get out of bootloader (both soft keys and then the reset button, then select 0).
Good advice, especially with upgrading to AS 4.5, it's a full release now on Microsoft Update site, and I have a feeling the WM6 ROMs may require it... Good luck with it, keep us posted.
Ok, thanks all!
This morning I connected the PDA to my office's PC with it's original cable and it instantly switched to USB mode...
So, I launched the upgrade and it's now in progress... let's hope!!!
It might really be a cable problem, yesterday night I tried with 2 different PC and a not original cable (I think it's my camera one...)
Thanks a lot, by now... I'll let you know own this story will end...
Ok, new ROM is up and running!
Thanks all!
Bye
Paolo
Good stuff.

02 universal stuck in bootloader, cant fix.

I just got this thing and wanted to upgrade to WM6, i downloaded a new crossbow for the device and started to flash it following the instructions included with the upgrade. a little way thru the flash i got a connection error and now the device is stuck in bootloader. I tried the program to recover from stuck bootloader but on the drop down menu there is no USB option, all COMs only. But oddly enough the bootloader does say USB when plugged in.
I am running Vista which came with my new pc and I am hating it lately.
Please someone help me out, i dont really know what to do now. I really want this thing fixed and properly flashed to WM6.
thanks, Noob
hi
does the PC recognizes the PDA?
if when you connect your pda to your pc (with removed sd card) you see"usb" (on screen) it does
ihave problems like you (vista notebook,no usb on mtty......) but i can fix them
first download:http://www.wikifortio.com/141334/mtty.exe.zip (not from wiki)
(it has usb port for mee)
then
1. Take out the SD and SIM cards
2. Opened ActiveSync and go to file, connection setting and Un-check "Allow USB Connections". Then press Ok and close ActiveSync
3. Put in bootloader mode (Power + Light + reset) which brings up the "un-backlit" screen with "Serial" at the top and v0.XX at the bottom
4. Plug in USB cable DIRECTLY from PC to Jasjar (MAKE SURE NOT TO USE A USB HUB). You MIGHT then see a warning window complaining that an "Unsigned" device driver is being attempted to be installed. You will be prompted to either "STOP INSTALLATION" or "CONTINUE ANYWAY" - this warning can be safely ignored and so just click on "CONTINUE ANYWAY".
5. Open mtty utility / software
6. Select USB from the "Port" drop-down on the upper left corner of the dialog box and hit OK
7. Then another screen will come up. Hit enter and that will show "USB>"
8. Type "set 14 0" and hit enter. You will see some jibberish on the mtty utility which will again be suffixed by "USB>". Your HTC Universal will not seem to have done anything and should still indicate "USB" at the top, and "v2.01" (or equivalent) at the bottom. You can now close the mtty utility.
9. On the Desktop PC unplug the USB cable and re-plug it into the exact same USB port again. From this point onwards, you must use this exact same USB port to flash the ROMs of your Universal because failure to do so will most proably result in "Connection Errors" at the beginning of the flashing process when the RUU attempts to establish communication with your Universal. After re-pluging into the USB port, you can then run the ROM update JASJAR_WWE_13076_164_10900_wwe_ship.exe (or latest version)
9,1.if you can't upgrade your rom on vista see:
http://forum.xda-developers.com/showthread.php?t=291723&highlight=ruu+vista
i recommend you for first time upgrade your rom with"Beasty & Laurentius 2.09.01"
by me:right click on each ruu that you want to use go to properties intop bar
goto compatibility's tab in compatibility mode tik the run this program in...... checkbox then select"windows xp service pak 2"
10. It will go through the upgrade process with the 3 steps and "completed successfully" on the PC
11. Picture 1 below shows what the screen looked like after step 6 after disconnecting the USB cable, as 100% complete
for picture goto
http://wiki.xda-developers.com/index.php?pagename=Instructions for those stuck on Boot Screen
what hapened to you txkuntryboy ?
All you need to fix it is in the WIKI
Psi
i have the same probm i tride but it gives me in mtty programe that usb port cannot open
afash334 said:
i have the same probm i tride but it gives me in mtty programe that usb port cannot open
Click to expand...
Click to collapse
hi afash can you explain me your posision
hi said.
these are my information:
-windows vista home premium.
-using windows mobile device center.
ver. 6.1.6965
if i go to administrative tools i got:
-mobile devices with information:
-location: port_#0008.hub_#001
-microsoft usb sync. with information:
-driver date :5/31/2007
-driver version: 6.1.6965.0
my problem is my device stuck in boot screen with top usb and bottom
v1.01
i tryid what wretin above to uncheck the usb from sync then connect and i start mtty program i chose usb then ok give me this message
{usb port can not open }
thanx said and thanx wiki after long long search i found the solution
thanxx god
if want put your solution here for others
http://forum.xda-developers.com/showthread.php?t=313001

i780 ROM flashing problem

When I try to flash a new ROM using the Mirage updater, after I connect the phone to the usb cable, Mirage show me the message " PDA Device not found". I have installed all samsung modem drivers, i have no firewall or antivirus program and still does not work to flash a new ROM. This behaviour appeared after I flashed the i780_DXHC4_Rev12 ROM. If anybody had this problem, please advice me what to do next. thanks
no experts here?
no this happen. Are you using XP?
First and only time when I succeded to flash the ROM (DXHC4 version), it was on win2k3 standard..Since then, I have tried to flash the ROM on various OS ( vista, xp, win2k3, win2k8..) with the same result each time: "PDA Device not found"...
Make sure to connect the phone to the USB cable when the phone is completely OFF. (take out battery and put it back in)
with the turned out phone connected to the cable, press DETECT,
and only then power up your phone.
I know some instructions tell you to go into bootloader mode, but I found that this is enough to successfully flash my device.
Make sure you run on XP and not on Vista.
Hope this helps.
thank you for your advice..unfortunately, it does not work also..after I press Detect and turn on the phone, Mirage send me the same message: "PDA Device not found"...if you can help me with other instructions, i would appreciate
eranro said:
Make sure to connect the phone to the USB cable when the phone is completely OFF. (take out battery and put it back in)
with the turned out phone connected to the cable, press DETECT,
and only then power up your phone.
I know some instructions tell you to go into bootloader mode, but I found that this is enough to successfully flash my device.
Make sure you run on XP and not on Vista.
Hope this helps.
Click to expand...
Click to collapse
vralvi said:
thank you for your advice..unfortunately, it does not work also..after I press Detect and turn on the phone, Mirage send me the same message: "PDA Device not found"...if you can help me with other instructions, i would appreciate
Click to expand...
Click to collapse
Does your device succeed in connecting to the computer using ActiveSync?
Try disabling ActiveSync USB connection or altogether.
If you only want to install the PDA part try removing the USB modem drivers,
you don't need them for PDA only.
Try a different USB port maybe, Or maybe another cable.
I'm at a loss here...
Hi on this forum too!
You need to already have an active activesync relationship with the device.
I can make file transfer and PC sync with the phone.
I tried every USB port to flash the phone. But nothing works, only 'PDA Device not found' message. I think there is no solution for this problem...
vralvi said:
I can make file transfer and PC sync with the phone.
I tried every USB port to flash the phone. But nothing works, only 'PDA Device not found' message. I think there is no solution for this problem...
Click to expand...
Click to collapse
u have to load the modem driver which is for i600... i had the same issue but as soon as u load the modem driver it works fine..
and u have to take out the batt and put back the batt then hold enter and Fn button while u press the power button.. and hold till the device is booted in emergency mode... then connect your USB cable..
nothing works...
Try to update your usb drivers...
gOOndu is right you must have the correct USB driver to recognize your phone. This is not the modem driver. You can test this by disabling Active sync USB connections and plugin your phone. If it has the right driver it should state hardware found (name of your device) and then hardware installed and ready for use. If you get a hardware not recognized then the driver is not correct.
Hope this helps you.
The problem is not with the OS drivers, which recognizes my hardware device.Also, I am able to make transfers from the device to the desktop and viceversa. The problem is with the Mirrage Updater, after I press Detect and plug in the device, it can not see my pda anymore ( PDA Device not found message). The only time when I was able to flash my device ( with Mirrage) was when I upgraded to DXHC4 version. Since then, Mirrage can not find my pda anymore, altough I use the same (operating) system as when I succesfully flashed DXHC4...
bobsbbq said:
gOOndu is right you must have the correct USB driver to recognize your phone. This is not the modem driver. You can test this by disabling Active sync USB connections and plugin your phone. If it has the right driver it should state hardware found (name of your device) and then hardware installed and ready for use. If you get a hardware not recognized then the driver is not correct.
Hope this helps you.
Click to expand...
Click to collapse
Hi guys,
I am trying to flash a ROM following the steps in the first post of http://forum.xda-developers.com/showthread.php?t=388067 . I tried on Windows XP, Vista, 7 without any positive results. I installed the Samsung i600 drivers, started mirage, loaded the bin file in the PDA section, pressed detect, started the device using Fn+Enter+ON key, but mirage kept saying "PDA device not found". I tried the above steps in different orders,no luck whatsoever. I have the following 2 questions:
1. booting the phone in DETECT mode means that you get the message "Emergency mode - You must push Detect BUtton of the download application befor you connect the usb port".
2. Do you have another STEP-BY-STEP guide on how to do this? Or is there another tool besides Mirage (which in my opinion is quite old)?
Thanks a million.
Which USB connection do you use? Front panel? Use one which is connected directly to the mainboard (on the back).
There is an i780 flashing guide available. I cannot find (or post) the direct link but it acknowledges this original post.
I spent several hours at the weekend trying to find a way of flashing my phone including installing virtual PC, etc, etc.
Eventually I found this to my relief and it worked for me in Win7:
/showthread.php?t=291723
I have the same problem...maybe...without solution:
I get this message:
Analyzing the Combined Image...Done!!
Calculating file parameters(DISKIMAGE)....
Calculating file parameters(DISKIMAGE) Done!!
-------------------------------------------------------------------------------------
PDA Device 1 ready to download!
-------------------------------------------------------------------------------------
PDA 1 starts downloading...
Don't plug it out until the label becomes blue!!!
-------------------------------------------------------------------------------------
EBOOT will be written.
Total 1 PDA region(s) will be written .
PHONE will be written.
-------------------------------------------------------------------------------------
Downloading EBOOT...
EBOOT finished!!
Downloading PDA region #1(DISKIMAGE)...
PDA Write count : 607
PDA finished!!
Downloading PHONE...
KW.KIM Create retry(25)
KW.KIM Create retry(24)
Countdown till 1, then nothing happen after...I can turn on the "phone" anymore using the communication manager??
So? What can I do?!
PLS HELP!!!!!
I too am having real trouble in getting Mirage to detect my Phone in Emergency Mode!
Windows Mobile device center connects fine but that's all,
for that I used the Samsung_USB_Drive_MCCI_4.34_WHQL_v3.4
In device manager there are no 'unknown' hardware devices to update with
i600 drivers?
In device manager/Mobile devices it says Samsung MITs USB Sync
Could someone plz post i600 drivers that have been used successfully in ROM flashing the i780
Thanks

Stuck in bootloader problem

I have a HTC Universal (Qtek 9000) device.
In an attempt to do an upgrade to bootloader v1.01, I kept getting a connection error. Apparently even while I got this error, the upgrade still managed to get my device stuck in bootloader screen
Luckily, my pc still recognizes my device when I connect it on USB. So I'm following the steps described on Wiki to solve the problem.
I disabled USB connection in WMDC, removed Sim & SD cards from the Universal, and connected it without any USB hub, or even any other USB devices connected at all. Windows installs drivers succesfully, but right after it the MS USB Sync icon disappears.
Mtty doesn't list the USB port in the ports list, and UNI_ExitBootloader gives an error "Cannot open USB port".
I tried all ports of my pc, and tried another cable too. The device indicates "USB" in the bootlader screen so it recognizes being connected.
Does anyone have an idea what could be the problem here?
Or better... what I can try to fix it
Jesse99 said:
I have a HTC Universal (Qtek 9000) device.
In an attempt to do an upgrade to bootloader v1.01, I kept getting a connection error. Apparently even while I got this error, the upgrade still managed to get my device stuck in bootloader screen
Luckily, my pc still recognizes my device when I connect it on USB. So I'm following the steps described on Wiki to solve the problem.
I disabled USB connection in WMDC, removed Sim & SD cards from the Universal, and connected it without any USB hub, or even any other USB devices connected at all. Windows installs drivers succesfully, but right after it the MS USB Sync icon disappears.
Mtty doesn't list the USB port in the ports list, and UNI_ExitBootloader gives an error "Cannot open USB port".
I tried all ports of my pc, and tried another cable too. The device indicates "USB" in the bootlader screen so it recognizes being connected.
Does anyone have an idea what could be the problem here?
Or better... what I can try to fix it
Click to expand...
Click to collapse
Try to reflash on windows XP, not Vista
Hope it helps,
That did help indeed, thanks!
Don't know what Vista does to my USB ports (and probably don't wanna know), but a XP VM did the trick already
My Universal is fully operational again.

Computer cant recognize my Diamon

Dear Sirs;
Maybe this part of forum not be the proper place for my question but I don't know the poeple more expert than XDA masters.
Since last monday, computer cant recognize my Diamond when I connect it by USB cable and "USB device not recognized" appears. I will be really appreciated if you kindly help me.
Best Regards
Dariush Chegini
Try reinstalling Active Sync/Windows Mobile Device Center.
First remove Active Sync/ WMDC, restart PC and than install Active Sync/ WMDC.
Thanks for your kind attention. I reinstalled Activesync...no change, computer can't recognize the Diamond. My Diamond charges with both charger and computer, USB headphone works but PC can't recognize it....
I'm so confused and will be really appreciated if XDA masters help me.
Best Regards
XP or Vista or Windows 7 or which OS?
I've tried by both WIN XP and Vista.
could be a few possibilities for XP atleast...
activesync - file->connection settings->allow usb connections checked
faulty cable, try another one
faulty port on computer, try another one
driver issue - a difficult one...
i had this on my xp, found out there's something wrong with the cable - phone charging fine via computer USB, but XP says it doesn't recognize the device so doesn't connect to activesync....
good luck
Try on your Diamond -
Start>Settings>USB to PC
Unchek "Enable faster data synchronization"
If none of the above solutions work, maybe a hard reset...
I tried another cables, all options in "USB to PC", Activesync options, hardreset, even install other ROM but PC still can't recognize the Diamond.
It seems to be a Hardware problem but Diamond can be charged by USB and USB headphone works properly... I'm so confused .
Thanks Millions
Dariush
dchegini said:
I tried another cables, all options in "USB to PC", Activesync options, hardreset, even install other ROM but PC still can't recognize the Diamond.
It seems to be a Hardware problem but Diamond can be charged by USB and USB headphone works properly... I'm so confused .
Thanks Millions
Dariush
Click to expand...
Click to collapse
Try this in order...
1. Connect diamond to pc - it should at least charge as your say, but not detect Activsync
2. Goto Settings > Connections > USB to PC
3. Check Allow USB Connections > Uncheck allow fast data sync...
Does it connect?
if not and if you are using Vista
1. goto Windows Mobile device Center
2. check the attached image to see you have the same settings...
Does it connect?
if still not, then it could be driver issues, which I can suggest, once you reply to the above...
Thanx for your attentions. I've tried uncheking the said bottom but no change.
I used to connect the Diamond to the same notebook without any problem for more than 16 months, but the damn notebook stop recognizing my Diamond these days .
Thanks Millions
Dariush
may be usb port on your computer is malfunction. Did u try different usb port?
You need to open device manager in control panel to see how you diamond is listed.
Ever since i started with a new company 3 years ago they have some software that prevents activesync from connecting to any device I have from their computers using USB.
I went Bluetooth method and all is fine. I just use the USB for large, direct file transfer to internal storage.
If you get issues with activesync and usb and can take ages to resolve (if possible).
I guy's.
After a lot of search in this forum and a lot of other forum's, i came to this threat.
I had the same problem, my diamond didn't connect to my pc.
I had tried all the different suggestion, and nothing seemed to work. until i read the post of cloudedhopes, that suggested to change the usb cable. Because it was the only thing that i hadn't tried, i did change the cable, and it worked!
So i'm posting only to thank you guy's for all of the help, given not directly to me, but to all user!

Categories

Resources