Hey,
I don't have any charger, so I have been always charging my Artemis via USB.
A couple of days ago it stopped charging. It happened after I discharged it to a very low level.
When I plug in the USB cable, the amber (or the orange) LED starts to blink. I can see the icon that says that the cable (which is ok) is plugged in, but the battery level is dropping instead of increasing.
I've tried even hard reset.
I haven't tried with another battery, but I've tried to charge the battery with a charger made by myself. It was OK - PDA is working, but I can't still charge it normal way.
Any ideas?
Blinking amber
I have the same problem on my htc p3300, and when i used batti 2.4 i saw that the battery temperature is 432675.5 etc something fake temerature. This is the reason, why my pda unable to charge my battery. If you set your pda in bootloader mode, it will charge your battery!. After 3 or more times i charged it in bootloader mode somethimes the battery temp sensor works normally, and the charge is working as well. Sometimes not.
Bat you can charge your battery allways in bootloader mode.
Sorry for my English.
Try it!
Good luck!
So it's a temp sensor problem? I've had the same problem with my SPV 650 a few times. Hopefully it was never permanent!
hey
Do you know how fix this problem ? Is there problem with battery or with mainboard ? I change rom, radio, battery, charger.If bootloader mode is the best solution?
I wait for answer and your ideas
Hi.
I have Prophet with the same problem. It doesn't charge batt, doesn't turn on - clouds then white screen. And it has happened after deep discharge.
Trying "bootloader mode"
i have the same problem with my dopod p800w. the device work only when it pluged, even when the battery is full (in another device) the notification message appear and it turn off ! Anyone can help me ? Sorry for my English !
im suffering from this problem
any solution?
i am about to purchase a new battery however.. i dont think that would solve the problem..
how do you enter bootloader menu?
Related
Hi there !
I hope someone could help with a weird problem.
history:
I've got a T-Mobile MDA compact 3 and I had an issue with my battery. It was completely discharged (~3% left, flashing red) and I was driving / navigating in the car until I noticed that the car-charger was not connected. So I plugged it in - and it was hot in the car... and the battery was GONE.
(I know that a LiOn battery does not like 'hot' ambient temperature, I know...)
At home, I tried to charge it with the power adapter : no luck.
OK, I thought, battery defect... so I bought a new one, Samsung labeld brand, not a 'China' clone.
Now, with the new one I've got the following problem :
- the battery will charge with either USB / car- or power plug charger, BUT it will go from consant organge (ok) to flashing orange (not ok, normally that's "notification" / message arrival) instead of green.
- using the power plug charger, after a night, battery is "empty" again, so charing (constant "orange" LED) -> flashing orange LED -> flashing RED in the morning -> empty
- the "BatteryStatus" tool and the system control panel will show "charging" while charging, but the percentage will never increase (e.g. if I start charging at 30%, it'll stuck on 30%...just displaying "charging"). If I now charge for - let's say 1h, it's still on 30% (despite, that I know it will last for 2 days)
So the problem is, that the PDA doesn't know the actual charging level. But that's also not true: cause if I do a Soft-reset, it's back at 100% (or less if I have not charged fully - which I don't know as it doesn't go to "green LED" anymore.
So again, in short, I always have to reboot to see the current charging level, and I'm missing the "green LED" full charge level (instead "orange flashing LED" notification.
I guess that the levels (low, high, current) are somewhere stored in the registry, or ? I did a hard-reset, reinstalled all applications, but same...
Any hints ? I hope a firmware upgrade would reset the battery status, but as there is no offical firmware for the T-Mobile MDA 3c, I'm stuck... or ?
I have the exact problem on my P3300... When i try to charge with my usb cable everything it's ok...
But when i am trying to charge with my car cable it will go from constant organge to flashing orange... Also the temperature is rising very fast... It has reached to 80 degrees C°
It stop charging when temperature is over 50...
Anyone there to help us???
I get a similar problem.
Allthough, charging on adapter "seems" normal.
Led turns green and battery status via system settings are at 100%.
When disconnecting from the charger, the battery level drops to the exact same level as before charging (example -> battery at 48% -> connect to charger -> after an amount of time LED turns green, battery status is at 100% on the PDA -> remove cable -> battery back at 48%).
Charging in the car or on the computer does not give this problem.
Tested my battery and charger on another unit -> no problem.
Tested another charger and battery on my unit -> same problem.
Device is going back (THIRD TIME in 2.5 months) for repair.
No more Artemis / HTC P3300 for me ......
hi guys,
i just checked out my ARTE160 battery. when i checked out the output voltage, i found that its 3.95~4.2 v when full charged. i jus checked this out with a multi meter. the battery is designed for 3.7v only, so does this mean there is a prob???
thx guys
I'm not a pro, but I think this means that everything is alright with the battery. I would rather worry if the voltage was below 3,7 V - that would definitely mean a problem.
well i find wat u say is logical but still im having some small prob in my phone.....
it keeps working well and suddenly the phone service alone wont work and gets hanged (means no calls and sms) after couple of mins mobile just researches the network and joins.
the prob is when this thing happens and someone calls me the call is ringing but i dont get any ring or alert in my mobile.......
also sms is not delivered kater but is lost completely......
i jus looked out somewhere that these probs may be due to battery........
Battery issue reply...........
nataraj_latest said:
hi guys,
i just checked out my ARTE160 battery. when i checked out the output voltage, i found that its 3.95~4.2 v when full charged. i jus checked this out with a multi meter. the battery is designed for 3.7v only, so does this mean there is a prob???
thx guys
Click to expand...
Click to collapse
I had to get a new battery and performed a hard-reset on my phone and all was well after that. make sure you have a back-up on your numbers....
well savain
thanks for ur reply.....
did u have the same kind of prob like the over voltage???
savain01 said:
I had to get a new battery and performed a hard-reset on my phone and all was well after that. make sure you have a back-up on your numbers....
Click to expand...
Click to collapse
I've just chcecked the output voltage of my battery - when 45% charged - the voltage was 3.82 V.
in my opinion, your problem has nothing to do with the battery. I had same problem that you described - I switched to WM6 from WM5 - it did the trick.
now it hangs very seldom.
I guess that would help you (at least if you're using WM5).
oh but im using 6.1 at present
its TOM'S ROM.....
...
*for battery issue;
buy a new battery and
charge <----- device must be off!...
when green led light shows, its done..
this should sort your battery issue..
* for issue with - ''suddenly the phone service alone wont work and gets hanged..''
try a hard reset, if it still happens, open the device - open through the back of the device and simply give it a clean, ensure all connections are connecting, in other words, scratch the pins inside device if they need it.. assemble correctly and hope this helps..
-use cotton buds, the ones you use to clean your ears with..
-use a pin/needle to scratch connections..
*sounds like a hardware issue, not rom issue so cleaning inside the device is recommended..
*I've fixed my p3300 plenty of times now by just simply cleaning inside it.
- including the ''not charging'' and ''no sim'' issue people have experienced..
Not charging
HI Geeks, I have a problem with my blackstone battery. It is getting charged only up to 50 to 55 percent. I kept on charger for one ful night. But no use. I am using official ROM. Can you suggest any solution for that?
Help PLZ
I tired both the charger and the USB cable. Still the problem remains.
A new problem
Now i am facing a new problem. When i switch off the Touch HD, it will not start. When i press the power button, it shows "Smart Mobility" then it will go off. I tried once and pressed the power button again. It lasted some more time, reaching to the HTC logo screen.
Then I Connect the phone using the usb cable to the desktop and press the power button. WOW. it started without any problem. Can you help me to get around this problem?
Roy Varghese
royi386 said:
Now i am facing a new problem. When i switch off the Touch HD, it will not start. When i press the power button, it shows "Smart Mobility" then it will go off. I tried once and pressed the power button again. It lasted some more time, reaching to the HTC logo screen.
Then I Connect the phone using the usb cable to the desktop and press the power button. WOW. it started without any problem. Can you help me to get around this problem?
Roy Varghese
Click to expand...
Click to collapse
*for battery issue;
buy a new battery and
charge <----- device must be off!...
when green led light shows, its done..
this should sort your battery issue..
i have a weird kind of battery issue
i plug in my AC adapter
the orange light lights up, for about 5 seconds
then , it keeps flashes orange
i power up my phone for about 5 seconds, it dies
any charge method will keep flashing orange
is my phone battery dead?
Does anyone have my issue ???
I am charging and charging and the indication shows as charging plus the percentage is increasing like normal. However, when I restart the system it shows more than charge percent. Most cases it shows 100%. For instance, show 82 % but after restart device shows 92 or 100%. Please help me experts. Thank a lot in advance for taking your time to reply
Hi,
Yesterday I came across strange issue. In WinMo, when the phone was off it was charging normally untill the battery was fully charged...
After Flashing Android to NAND I can not do that. It seems to be charging (orange LED is on) for about 10 sec. and than the Display blinks with white light and the phone dies completely.
The only thing you can do after that is to pull out the battery and put it back. Than you can turn the phone on and charge as usually.
What is that issues origin? Battery driver? Or another thingie in Firmware? It seems to be quite strange, that it lights the display even with the phone being off...
a.s.j said:
Hi,
Yesterday I came across strange issue. In WinMo, when the phone was off it was charging normally untill the battery was fully charged...
After Flashing Android to NAND I can not do that. It seems to be charging (orange LED is on) for about 10 sec. and than the Display blinks with white light and the phone dies completely.
The only thing you can do after that is to pull out the battery and put it back. Than you can turn the phone on and charge as usually.
What is that issues origin? Battery driver? Or another thingie in Firmware? It seems to be quite strange, that it lights the display even with the phone being off...
Click to expand...
Click to collapse
i have this problem too
a.s.j said:
Hi,
Yesterday I came across strange issue. In WinMo, when the phone was off it was charging normally untill the battery was fully charged...
After Flashing Android to NAND I can not do that. It seems to be charging (orange LED is on) for about 10 sec. and than the Display blinks with white light and the phone dies completely.
The only thing you can do after that is to pull out the battery and put it back. Than you can turn the phone on and charge as usually.
What is that issues origin? Battery driver? Or another thingie in Firmware? It seems to be quite strange, that it lights the display even with the phone being off...
Click to expand...
Click to collapse
My Kaiser does the exact same thing, and what it is, is for some reason the phone is booting back up. I came across this the other day, and my phone did the exact same thing described, and not sure what I did, but I managed to turn on the screen and Android was booted up to the lock screen.
It's even done it when I plug the phone into A/C power without the battery even connected.
so here is why it happens, basicly what would happen is in WinMo when the phone would turn off and boot into a charge loop and it would charge and shut off when finished our kernel doesnt have this built into it so it just boots like normal when power is applied
thoughtlesskyle said:
so here is why it happens, basicly what would happen is in WinMo when the phone would turn off and boot into a charge loop and it would charge and shut off when finished our kernel doesnt have this built into it so it just boots like normal when power is applied
Click to expand...
Click to collapse
yup... happens to all of us, its not a big deal... there are a lot of worse problems devs are trying to solve... maybe whn they reach a point where the kernel is more stable they should pay attention to the details like this (and the camera driver, camcoder... etc)
thoughtlesskyle said:
so here is why it happens, basicly what would happen is in WinMo when the phone would turn off and boot into a charge loop and it would charge and shut off when finished our kernel doesnt have this built into it so it just boots like normal when power is applied
Click to expand...
Click to collapse
Well that answers my question... Yah knew it was something inside the kernel, just didn't know if it was a bug, or something that wasn't implemented yet.
Of course this is low priority task but I just wanted to have that confirmed to know, that my oldie holdie is not broken or what
Quick question:
How old is your kaiser and/or battery ?
About 5 years with original battery
Sent from my Full Android on Kaiser using XDA App
It used to be that if Linux NBH was flashed, the phone wouldn't charge at all when off. Then somebody (dzo I believe) added code to the kernel so that the phone turns on when it is plugged in, so that it will charge. That used to work, with a full complete boot. Now, as you say, the phone tries to wake up but doesn't really make it. Maybe we should look into that, we should be able to fix that, maybe by looking carefully at the git logs for the past six months or so.
There are bigger problems, like data reliability, but if somebody wants a problem in the kernel that they can study and perhaps fix, this is a good one to start with.
To correctly charge the battery system need to be on so i can do this:
start kernel
in initrd:
if it found the power connected then the phone wait for power button (trying the sleep mode)
else
start the system
i need some testing to do it.
Windows do quite the same thing.
l1q1d said:
To correctly charge the battery system need to be on so i can do this:
start kernel
in initrd:
if it found the power connected then the phone wait for power button (trying the sleep mode)
else
start the system
i need some testing to do it.
Windows do quite the same thing.
Click to expand...
Click to collapse
If only the real code was as easy as the pseudocode =)
Apologies for another not charging thread, i have tried searching for a similar issue but no luck.
I put my DHD to charge as usual last night at around 40%, the charge LED lit up and the battery icon was showing that i am charging.
When i woke this morning, the charge LED and battery icon were still showing that i should be charging yet the phone now only has 33% battery, so clearly hadnt charged. I checked current widget and when the LED and icon show charging i only seem to be getting anywhere between a reading of 40mA and 270mA. With an occasional 300-400mA reading.
I seem to be able to intermittently get the phone to charge and the batt icon to rise by a percent or two but then it seems to stop again. As i am in work at the moment i am having to charge via USB from my PC. Therefore i am currently unable to try another micro USB charger and see if it is indeed the charger or the phone.
Has anyone else had a similar issue, says it charging but it not??
Or anyone have any ideas of a solution??
If it matters i am currently using LeeDrOiD HD V3.3.1 GB. Id rather not have to return it to HTC as i am unsure of how to return the phone to default easily so it could be repaired on warranty.
Thanks in advance,
James
Firstly, download CurrentWidget, set refresh to 15 seconds, and make sure you set it to display battery voltage. If it is showing around 4200mV, it is charged, and you have a problem with the battery gauge.
To double check, turn off your phone, and see if the light goes green at 100%.
Boot back up, just to see if a reset fixes it.
If not, reboot into recovery, and wipe battery stats (or do it properly, turn off, wait until light is green, wait another hour, then boot into recovery and wipe battery stats).
Turn back on, and see if the problem is sorted.
Sent from my Desire HD using Tapatalk
I'm hoping some of you wise heads on here might be able to help me out with a problem that has got me totally and utterly stumped!
Last week I was using my One X and noticed the battery was down to aorund 14%. I plugged it into a charger and nothing happened...no light...nothing. I tried various different chargers and cables to pc etc and nothing seemed to do anything.
After leaving the phone plugged into the mains for a few hours, I noticed that a very slow/long flashing red/amber light appeared. It kind of stays on for 5 seconds and then off for the same amount of time. I left the phone in this state for about 14 hours and when turning on it would say battery was somewhere between 0%, 1% and 2% and would promptly switch itself off.
I messed about for hours on end trying many different button combinations, sim in/out and came to this bizarre conclusion.........If I plug the phone into the mains for a few minutes, then press power and volume down to get to the HBOOT menu then hold power in again to reboot, the phone reboots into the OS and is functional. It still reads as having 0% or 1% battery and shows as not charging, but it must be getting some juice for it to be working. If I leave the phone in this state for a while I can then unhook it from the charger and use it as normal, even though battery is displaying as 0%. I can use the phone like this for some time, although the battery does not appear to last as long.
Also, the phone is not recognised at all by the PC when plug in via usb when in android os - nothing at all shows in device manager, but it is recognised from the fastboot menu and tries to install device drivers.
Has anybody got any clue if I can save my HOX or am I without a paddle?? Many thanks in advance