Related
I follow instruction in http://forum.xda-developers.com/showthread.php?t=313486 but after hardreset.
My p800w is stuck in T-Mobile logo and version number. It can't continue booting up to windows mobile.
Question: How to flash ROM without ActiveSync?
How to recovery my Artemis?
Welcome any advice,
Thanks in advance.
Yea me to, mine is now a brick after that upgrade? No active sync connection possible and all I get now is the blue O2 start screen after the hard reset with the red writing and numbers in the top left hand corner..
Phone is an UK XDA Orbit
IPL 1.25.0001
SPL 1.11.0000
GSM 02.67.90
OS 3.4.0.0
HELP!!!!!!!
yeah, I had the same problem and have created a thread for it already. unfortunately I got no useful replies, and it seems that I am stuck waiting for an official o2 ROM so that I can recover my Orbit.
It seems there is a way to un brick our phones I just need to get my phone bootted into bootlader mode which no one seems to say how to do??
Can anyone help how I can boot my Orbit , like what combo of keys I need to press to boot it into bootloader mode then XP will see it at a driver level apparently Active Sync still won;t but I will be able to run some German ROM update with the ROM file replaced with the other ones and it may come back to life..
Help how can I boot my phoen in bootloader mode???
motomob said:
It seems there is a way to un brick our phones I just need to get my phone bootted into bootlader mode which no one seems to say how to do??
Can anyone help how I can boot my Orbit , like what combo of keys I need to press to boot it into bootloader mode then XP will see it at a driver level apparently Active Sync still won;t but I will be able to run some German ROM update with the ROM file replaced with the other ones and it may come back to life..
Help how can I boot my phoen in bootloader mode???
Click to expand...
Click to collapse
I read in here that you hold the voice button and soft reset.
Decaf said:
I read in here that you hold the voice button and soft reset.
Click to expand...
Click to collapse
Correct and use mtty
Already see in the forum ....
Thanks guys and apologies for the spelling..I ran the Artemis_USPL before I tried upgrading to WM6 and again have been able to run it after with my new brick now with the phone in bootloader mode but still when I try and run the german ROM update a) it will only work with the german file which freezes @ 3%? This seems to be a known problem reading around and b )when I replace it with the smaller ROM file, 54MB the german one is 66MB, I originally tried to use it doesn't read the ROM file or the update utility doesn't want to read it. I reckon I might be able to get it back if I can get one of the ROM update utilities to read a good ROm file and send it to the phone.
I can;t find this MTTY program to sniff the USB port and return the code of if the USPL util wokred as I think that could be key to all of this.
Can anyone post a quick how to here for
1) install MTTY from somewhere
2) what command to run agaist the phoen to see if the USPL util worked and what values I should be looking for
3) another WM6 ROM version (that the update utils can read) download location I can download from to try and send to the phone using the German update util
Not asking for much am I but I desperately need my phone back WM5 or 6 in the next day or so so really can't send it off.
Thanks
Error message I recive at the 3% stage when using the German ROM and english update util.
use the file attach and read that :
http://forum.xda-developers.com/showthread.php?t=285112
Thanks but I'm not that cleud up on what commands I'm meant to be sending. It works in Bootloader mode I ge a response from the phone by send it a command. But even if I get a response telling me what the CID status is its not much help as I think ti shoudl have tekane BEBEs ROM by now as I've got the german ROMUpdateUtility sending that 54,272KB file to the phone but it stops after 3%. What are my options?
motomob said:
But even if I get a response telling me what the CID status is its not much help as I think
Click to expand...
Click to collapse
That's right. On older models MTTY was quite useful, but not on the Artemis. You cannot use it to read the CID status anyway. If you are not sure about the status, run the USPL tool, just to make sure.
I've already re run the USPL ROMUpdateUtility and it completes 100% okay in bootloader mode. But after I hard reset and then try and flash the WM6 BEBE ROM or any ROM German etc back onto it it either fails with the error code I posted up earlier or gets to 3% and fails.
What are my options at this stage? Does anyone have a link to another ROM I can try like the original WM5 O2 ROM or any other WM6 ROm that might work. I'm willing to give them all a try as it's just a useless phone right now and I haven;t sent it off as 1) I need it before the weekend and 2) As I can flash some ROMs with the USPL and others have done this no problem I really feel there must be a solution as I can still falsh the phone.
What can I say RTFM... I did it all right and I didn't have a brick, I missed out one small detail... loading on the ROM with the extended ROM. All now running and it does seem a little faster than WM5.
Thank you to all those that tried to help out. To the others that are still having probs.. Don't try and run the update in the middle of a busy day in the office whilst trying to manage 100 other things meaning you are probably missing out a line like me...
One question though how do I get back my O2 power and storage meters on the today screen back as I liked them and the WiFi seems to have a bug where when it is enabled and you click on the WiFi symbol up the top it only allows you to switch it on, when it is already on.. so you have to open up the COMM manager to switch it off.
So how did you fix it exactly? I have read this thread thoroughly and can't find out what you did!
ERROR[206] occurs while trying to update ROM to WM6
While tring to update ROM to WM6 on O2 XDA Orbit i encounter ERROR[206].
I wanted to attach the screen shot but dont know how to do that, but anyway what i am doing is i attached my pda to my pc via activesync using supplied usb cord. Everything goes well till i reach a screen where it says "You are now ready to update your ROM image...." and once i click next a progress bar apperas and my pda shuts and activesync exit's automatically and my pda tries to restart with RBG band and some text:RUU, IPL 1.25.0001, SPL 1.25.0000 and USB. And thats it after few seconds or a min i get the ERROR[206] and my pda hangs.
I dont know why Activesysn shutsdown ???
Just an additional in i want to tell that without installing activesync i am not able to connect/pair my pda with my pc. So do i need to install the drivers and then try or it doen't matter cause once i install Active sync i can connect the device.
Please help me with this....
Thanks
unable to load bootloader!!!!!!!!!!!!
HELP!!!!!!!!
I have HTC3300, tried to update rom, now its bricked. I tried to start bootloader by pressing the voicebutton and softreset but loads in t-mobile screen and hangs, im unable to start the bootloader.
Is this end of story or are there any other options to get the bootloader to start????
please help
Bootloader
I had a problem with my phone loaded touch flow 4 and cid unlocking, everything was fine then after a while it froze at boot up.
I look put the battery and did a hard reset, put it into bootloadeder mode, reflashed with a t-mobile rom does not need to be cid unlocked to do that.
Once origonal rom was working, cid unlock again, flashed back to touchflow 4.0 - sorted
Where did you got an tmobile rom from can you tell me. Mine is also freezing on booting almost once every day or so after I've upgraded to 4.0
Hi!
I just got myself a Diamond and im trying to upgrade it. I've read the following tutorial: http://forum.xda-developers.com/showthread.php?t=416211 but the Upgrading to HardSPL doesnt work for me.
When RUU starts updating, the screen on my phonescreen turns black (as it should do) but at the same time it disconnects from the computer and the program. and the phone freezes and i have to take out the battery and reset it. I've tried to repeat it many times, i also changed the power settings and everything.
I have ROM version: 1.93.413.3 SVE and Radio: 1.00.25.05 and Iam trying to update to SwiftBL
Thank You
After your screen turns black, don't flash the SPL yet.
Wait a while till you pc detects the "new" device and installs drivers for it.
If you have still troubles, PM me and we can do it together ...
sum1 help me out plz
oryt mate
sorrry to bother u
erm im on vodafone wiv the vodafone rom thing and i tried puttin a different rom on but it does'nt move past 0%
so i tried that olinex thing and thats not helpd either
stil stays at 0%
any tips? let me knw please
thanks
I have the same problem as stated above..
Screen turns black..
Phone gets disconnected from pc..
Windows is found a new hardware device and is asking for a hardware install..
Hardware Install Fails and phone remains disconnected with a black screen..
WHAT TO DO NOW..?????
I'm afraid of disconnecting my phone, because of the chance ending up with a brick.
Can someone please help me out..???
It happened to me before. For me it was due to the advanced battery setting.
I resolved it by unchecking "turn off device if not used for.." on both battery and external power. Hope this helps.
Nope this does not help..
My phone goes black and dissconnects from the pc and does not reconnect..
Get a connection error from the hardspl update program and have to remove battery to restart phone
Doe anyone have an idea what i am doing wrong..???
I have the same problem. and i have tryed everything...almost:S
Thank you all!
Thank you all for the quick replys,
I've found a solution to my problem.
First of all i unchecked all the battery saving options, and then i went to Settings--> USB to PC--> and uncheck the "Enable advanced network functionality" box, after this the upgrade worked.
Hope this works for you guys 2
Peace
Not working for me here . Htc Diamond from H3G ITA .
I can't get past the black screen . Activesync disconnects and never connects again ... I tried the 2 settings changes proposed here ; I tried waiting almost 10 minutes on the black screen ....
Any other ITA H3G user with the same problem (maybe solved....) or any other user that got away with this huge problem ??
Have you tried pasting SSPL-Manual.exe into Diamond's Windows directory and executing it?
I put it in the root and executed it .... screen went black ... activesync lost connection ....................... after 20 minutes still black screen and nothing happened .
Fortunatly unplug battery and restart got me the pda back working
PS. If I enter the multicolor screen I see as SPL 1.37.0.0 and above it says DIAM100 ..... if any of this info could help to get me more help
don.sina said:
Thank you all for the quick replys,
I've found a solution to my problem.
First of all i unchecked all the battery saving options, and then i went to Settings--> USB to PC--> and uncheck the "Enable advanced network functionality" box, after this the upgrade worked.
Hope this works for you guys 2
Peace
Click to expand...
Click to collapse
Worked like a charm for me
Thanks
grebbo said:
I put it in the root and executed it .... screen went black ... activesync lost connection ....................... after 20 minutes still black screen and nothing happened .
Fortunatly unplug battery and restart got me the pda back working
PS. If I enter the multicolor screen I see as SPL 1.37.0.0 and above it says DIAM100 ..... if any of this info could help to get me more help
Click to expand...
Click to collapse
I believe that is what will happen. I used this method to install 1.40.
After you get the black screen just follow instructions from step 2 in here:
http://modmydiamond.info/index.php?option=com_content&task=view&id=22&Itemid=26
Ignore the activesync turning green part.
The small words in the red box is easy to miss out.
had a similar problem...upgrading to the latest version of .net CF did the trick for me....u might want to check that out (nothing to lose in having an updated version anyway)
Tnx a lot catpuke ... I tried to run the update anyway even with no sync with pc .... it stayed to 0% for a little bit and then jumped to 100% .... now in tricolor shows 1.30 Olinex !
Will move on and try to update radio now !
Tnx again for the help
Hey help me please!!
Please brother's help me!!
I have a Diamond, and yesterday I try to upload my phone with a rom
At the moment it's load perfectly, so after the program has finished the atualization, my phone make a soft reset(normal), So when wake up, and show's me a boot screen with (TOUCHdiamond) name on the screen, he freeze!!
I can't do nothing! It's stuck!? omg! people help me to resolve this!? I try up a new rom but isn't work cause the phone don't connect with windows to change or execute other program, cause the phone are stuck on boot screen!
Please!!! HELP ME TO RESOLVE!!! PLEASE!!!!!
c ya!
thx for all
dehzincwb said:
Hey help me please!!
Please brother's help me!!
I have a Diamond, and yesterday I try to upload my phone with a rom
At the moment it's load perfectly, so after the program has finished the atualization, my phone make a soft reset(normal), So when wake up, and show's me a boot screen with (TOUCHdiamond) name on the screen, he freeze!!
I can't do nothing! It's stuck!? omg! people help me to resolve this!? I try up a new rom but isn't work cause the phone don't connect with windows to change or execute other program, cause the phone are stuck on boot screen!
Please!!! HELP ME TO RESOLVE!!! PLEASE!!!!!
c ya!
thx for all
Click to expand...
Click to collapse
Here's what you need to do:
Hold down the "Volume Down" button and press reset with the stylus. You will enter the Boot Loader. Now plug in your USB cable connecting it to you PC. On the bottom part of the screen (phone) you'll see USB. Now your PC recognizes the phone.
Start a ROM update through the RUU executable and flash your phone with a different ROM.
henk2484 said:
Here's what you need to do:
Hold down the "Volume Down" button and press reset with the stylus. You will enter the Boot Loader. Now plug in your USB cable connecting it to you PC. On the bottom part of the screen (phone) you'll see USB. Now your PC recognizes the phone.
Start a ROM update through the RUU executable and flash your phone with a different ROM.
Click to expand...
Click to collapse
thx!! really appreceate!!! thx! it's back to work! thx!!!!!
i have the same problem where my phone freezes at the boot screen, where it says touch diamond and thw orange writing in the corner. It was working fine, happened all of a sudden after i soft reset it, when the phone initally froze on an incoming call
Any suggestions?
just Change your ROM..,
hard reset is somthing i dont want to do. Is there any other option?
kerm said:
hard reset is somthing i dont want to do. Is there any other option?
Click to expand...
Click to collapse
I think not. Don't know if you have a lot of apps installed after flashing. What you could do is find a ROM that's UC2/sUC compliant. If you create a folder structure on your internal storage like this:
ROOT > Backup and Restore > CAB > CABi
Put all the cabs you want on your device in the CAB folder and all the cabs you want on internal storage in CABi folder. After flashin and initial customization you will find yourself in User Customization (UC). It will state that it found a CAB folder, choose to install. After this it will state that it found a CABi folder, install as well. This reduces the effort of installing all apps after a hard-reset. As for messages, contacts e.g. I suggest you use PPCPimBackup.
same problem, but when I launch the ruu all is ok, until it starts, it stay at 0%, then I get a message that there was a communication error
Go1den3ye said:
same problem, but when I launch the ruu all is ok, until it starts, it stay at 0%, then I get a message that there was a communication error
Click to expand...
Click to collapse
Try flashing through bootloader. Press reset with stylus while holding volume down. After you're in the bootloader plugin USB cable and start flashing.
henk2484 said:
Try flashing through bootloader. Press reset with stylus while holding volume down. After you're in the bootloader plugin USB cable and start flashing.
Click to expand...
Click to collapse
tried and didnt work. made it worst in fact :S
startet update trough bootloader, started, updated to 13% and then I was told the update didnt work with my device (or something similar, in norwegian). tried an older update, same problem... :/
when I now boot the phone I'm directly in bootloader, and with the funny message
DIAM100 65M
SPL-2.03.0000
PSOC-Diam STAGE_PVT v0x30
Upgrade ROM code error
Please try again
I might have my hand on a brick... but hope not...
edit:
ooh, news, suddenly its updating moore... after 5 tries it allways stopped at 13%, but now it up to 31% and going strong... will update..
edit2: going strong up to 33%....... wow... well its a start and Im going to try some more.
edit3; 7th time the charm it seems... 100% and all I had to do was sit REALLY still. and I actually downgraded from 2.03 to 1.93 or something... should note that on this point I have tried flashing it with the original 2.03 and 1.93 every other time...
edit4; aaaaand we're back at the TOUCH Diamond screen.
edit5; aaaand after a failed flash to wm 6.5 (stopped/didnt start at 0%)... the phone started... This MIGHT be a clue that I should NOT try to get wm6.5 to run... but that wont stop me
I dont know if anyone else will have the same problems, but atleast this was my way to the resolution
Go1den3ye said:
tried and didnt work. made it worst in fact :S
startet update trough bootloader, started, updated to 13% and then I was told the update didnt work with my device (or something similar, in norwegian). tried an older update, same problem... :/
when I now boot the phone I'm directly in bootloader, and with the funny message
DIAM100 65M
SPL-2.03.0000
PSOC-Diam STAGE_PVT v0x30
Upgrade ROM code error
Please try again
I might have my hand on a brick... but hope not...
edit:
ooh, news, suddenly its updating moore... after 5 tries it allways stopped at 13%, but now it up to 31% and going strong... will update..
edit2: going strong up to 33%....... wow... well its a start and Im going to try some more.
edit3; 7th time the charm it seems... 100% and all I had to do was sit REALLY still. and I actually downgraded from 2.03 to 1.93 or something... should note that on this point I have tried flashing it with the original 2.03 and 1.93 every other time...
edit4; aaaaand we're back at the TOUCH Diamond screen.
edit5; aaaand after a failed flash to wm 6.5 (stopped/didnt start at 0%)... the phone started... This MIGHT be a clue that I should NOT try to get wm6.5 to run... but that wont stop me
I dont know if anyone else will have the same problems, but atleast this was my way to the resolution
Click to expand...
Click to collapse
Before you try to flash anything other then a stock ROM, I suggest you take a look at this thread: http://forum.xda-developers.com/showthread.php?t=416211
You need to have Hard-SPL flashed before flashing any custom ROM. My advice would be to use this one: http://forum.xda-developers.com/attachment.php?attachmentid=93362&d=1213719705
cool, will try that one. thnx
On My New Diamond having 1.37 Asian HTC ROM i Flashed 1.93 Asian HTC ROM. It flashed successfully then after installing some programs i have done the soft reset after that It hangs on Operator (Airtel) Logo and my phone doesn't start. I have not installed
any Hard SPL.
I have done Vol.Down + Softreset button but nothing appears on screen.
I tried to Hard Reset but nothing Happens
plz plz help me
dalco said:
On My New Diamond having 1.37 Asian HTC ROM i Flashed 1.93 Asian HTC ROM. It flashed successfully then after installing some programs i have done the soft reset after that It hangs on Operator (Airtel) Logo and my phone doesn't start. I have not installed
any Hard SPL.
I have done Vol.Down + Softreset button but nothing appears on screen.
I tried to Hard Reset but nothing Happens
plz plz help me
Click to expand...
Click to collapse
Did you hold the volume down button while pressing reset? After pressing reset you should keep holding the volume down button until the tri-color bootscreen appears.
i have flashed my diamond with the official htc rom
im on 1.40 olinex, now i can only access boot mode.
sometimes if i leave the phone without a battery for like 2 hours, when i turn it on i see the "touch diamond" logo, if i leave the battery for a whole day i see the windows mobile loading screen, but then suddenly the phone turns off
plz if you have any idea about this problem help me
If you can acces bootloader, then your diamond isn't bricked.
Try the unsigned version of olinex' hard-SPL and flash the ROM again.
Good luck!
hey ElCondor, im on 1.40 olinex, i cant flash it because it is protected
how can i flash the unsigned 1.40 olinex one?
Here is a link to the unsigned hard-spl.
Make sure you download "Unsigned-Hard-SPL-Diamond-OliNex.zip".
Follow the instructions:
1) Download, extract to an empty folder.
2) Run RomUpdateUtility.exe, Have Phone Synced with PC (go into bootloader, connect your cable, then the word "serial" in bootloader will change into "USB".
3) follow steps, check device for prompts after PC shows loading bar. it should go to black screen now.
4) SPL flashes, device automatically reboots, job done.
5) to confirm you got it installed, go into bootloader mode (volume down + reset, i.e. press volume down button and reset then keep holding the volume down key until you see tricolour screen) and verify the screen shows 1.40.OliNex.
note: you will not see the SPL version during normal boot, that is the OS version, not SPL!
Installing this will hard-reset your device.
Best Regards,
ElCondor
when i flashed the unsigned 1.40 olinex, the device rebooted
windows mobile is preparing your phone for first use
htc logo
phone went off :S
will try flashing rom again
flashed ROM again, now it wont boot up no htc diamond logo no nothing
i can access boot mode (1.40 olinex unsigned now i guess)
is there no way i can boot the rom? what seems to be my problem?
mzaouar said:
flashed ROM again, now it wont boot up no htc diamond logo no nothing
i can access boot mode (1.40 olinex unsigned now i guess)
is there no way i can boot the rom? what seems to be my problem?
Click to expand...
Click to collapse
Hi
If you can access the bootloader then your device is not bricked. Therefore download a rom of your choice then connect to the usb when on the bootloader then use a Diamond custom RUU (normally come with the rom) follow the steps. After rom updated make a hard reset. I hope it will run ok.
Looks your symtons are showing like your rom corrupted.
Good luck
i am flashing this ROM
RUU_Diamond_HTC_Europe_1.93.401.2_Radio_Signed_Diamond_52.29.25.12_1.00.25.05_Ship
the newest one i downloaded from htc. com is giving me rom update error
would you recommend a good rom for my phone?
after flashing and reflashing and hard resetting with the ROM showed above
still cant boot in ROM mode, only in boot mode
el condor sabes, anything ???
should i flash with a new rom, and if yes with which?
(diam100 olinex 1.40 unsigned)
Perhaps try a custom rom?
I found when flashing to an official rom from a different provider (my phones telstra and was flashing 3) I had issues with the rom booting and had to follow a post on here somewhere to get it working, however When I had this problem I could still flash any custom rom with no issues.
Unless its for warrenty purposes then its probably not worth flashing the "original" perhaps flash A.Z.T.O.R. = Alpha Zero Tweaked Official Roms which are close to the original but with benifits of being modded for faster speed etc.
Anyways Im no pro but I know what you are going through and I am trying to find the link to the fix to your problem as I also had the problem. But recommend trying a custom rom to confirm the problem is the same as mine.
For the record now I do not use official roms anymore, with WM6.5 running well for the most part on the diamond its a great step backwards when you revisited 6.1
flashed to SwiftBL-WWE-Diamond-v7.5-Full-16MbPP
still same problem can only go to boot mode
i am feeling there is no solution to my problem ?
is the phone bricked? :S
If you haven't done yet, flash the hard-spl I posted. Just do it, re-instal the hard-spl! Then, flash another ROM, maybe (as said before) your rom is corrupted.
The problem here is, that you first installed the unsigned hard-spl, and then flashed a corrupt rom. In that way, the hard-spl can be damaged too, so flash the hard-spl again and flash another rom should work.
Good luck!
I did :S but to no avail, I will do it again fingers crossed :S !
update: weird, everytime after i flash the hardspl unsigned, it boots up, i can see the "touch diamond" logo
windows mobile booted.. preparing your device..
update 2: windows mobile booted, installing everything
omgomg it looks it might work this time, fingers still crossed !!
el condor !! haha fingers crossed
update 3 :S : windows mobile installed properly, phone rebooted, went again and opened it, then i heard a sound from the speaker and the phone turned off :S
it must work what could the problem be now? last step !
Okay try a hard-reset, maybe that works.
If not, then flash hard-spl again, then hard-reset, then flash another ROM. Then hard reset. Then try again if it boots.
Is your battery enough charged? That could also be a reason.
did not work, wont even boot up
when i said if i leave battery out and such, I thought it might be hardware/heat related
http://www.htcwiki.com/thread/2069847/HTC+Diamond+-+Severe+Crashing+Problem,+maybe+heat+related
could this be it? will i have to send my phone for repairs?
because maybe when WinMo was loaded, the phone started to heat up and it shut down
so basically my solution is not a software fix??
If none of the tips worked, and you have the same problems as described in the site you linked, then you probably have to send it back.
One thing you could do: Try if the other hard-spls (1.37 and 1.93 unsigned) are working for you.
I'm sorry for you, maybe someone more skilled than me (like cmonex or olipro) knows how to solve your problem.
it's alright :S i thank you for all the help you have offered !
( it is customizing right now) but i expect it to reboot anytime now
worked, 5 minutes into winmo it restarts
mzaouar said:
worked, 5 minutes into winmo it restarts
Click to expand...
Click to collapse
oh,does it worked?how can you get it work?Please tell me....my diamond could only get in the bootloader yet....
mzaouar said:
worked, 5 minutes into winmo it restarts
Click to expand...
Click to collapse
OK good to hear that, if you have any more questions in future, just ask!
Glad to be of some help
msvb007 said:
oh,does it worked?how can you get it work?Please tell me....my diamond could only get in the bootloader yet....
Click to expand...
Click to collapse
Ive sent you a pm, there's no need to use this thread for your questions because the problem in this thread is solved.
So take a look at your pm!
Hey guys, I've been looking for answer for my problem for several hours without any luck. When my phone is not plugged to USB it won't even start in bootloader mode nor the hard-reset works. When I plug it to USB then it starts in bootloader mode says Upgrade ROM code error Please try again. This screen shows only for about 2 seconds and the phone restarts itself and does the same over and over ... I'm getting desperate. Does anybody know what to do with this issue?
Am also having the same problem since yesterday. My HTC Diamond touch2 had the wm6 from htc..the battery was after every 9hrs dead so i decided to flash the "shania" rom which many says is better. The installation was all fine and shania started.I removed the Batt to put the sim-card and restarted the Phone. It did`nt start and now it gooes on and off with the bootloader tricolor and says "No Image". No access to pc due to "on/off" state. Please Help
No one can Help???
Have also tried to flash using an sd-card without success. The phone does not even charge itself. Please S.O.S
I have a similar problem on my Rhodium (tilt2). Been reading around on and off for a couple days now and have come across a couple possible solutions. I'm still experimenting with my phone.. going to poke around with mtty on my roommate's PC later today. I'm still searching the xda threads (which led me to this post) so I'm sure there is a solution which doesn't involve a service center or warranties. I did read one post about charging the battery in another HTC device and then re-flashing yours with the fully charged battery.. but I don't have that option myself.
cafecz said:
Hey guys, I've been looking for answer for my problem for several hours without any luck. When my phone is not plugged to USB it won't even start in bootloader mode nor the hard-reset works. When I plug it to USB then it starts in bootloader mode says Upgrade ROM code error Please try again. This screen shows only for about 2 seconds and the phone restarts itself and does the same over and over ... I'm getting desperate. Does anybody know what to do with this issue?
Click to expand...
Click to collapse
Do you have hard-spl and what model of diamond do you have,cdma or gsm?
HELICOPTER88 said:
Do you have hard-spl and what model of diamond do you have,cdma or gsm?
Click to expand...
Click to collapse
I'm sure I have GSM phone. I have HTC Diamond Touch P3700. I sucessfully installed Hard-SPL Olinex 1.40. But then I read there might be some problems with 1.40 version so I tried to downgrade to 1.93 and then this ON/OFF problem started.
cafecz said:
I'm sure I have GSM phone. I have HTC Diamond Touch P3700. I sucessfully installed Hard-SPL Olinex 1.40. But then I read there might be some problems with 1.40 version so I tried to downgrade to 1.93 and then this ON/OFF problem started.
Click to expand...
Click to collapse
a lot of time ago i read about upgrading from 1.40 to 1.93 and there was some problem,i don't remember where i read it,i'm not having any problem with 1.40
ok, later i also found out that 1.40 i fine. But it doesnt solve my problem right now. Any suggestions?
Bootloader´s "On/OFF" Solved
I cant believe it...my phone is breathing again..
Somehow I had the feeling that the phone wasnt charging at all. i also read in a forum that one should try to charge the batt in another device but i knew no one with my model..and this is what i did..
1) Connect to pc through USB
2) removed the battery from the phone
3) walla....Bootloader doesnt go off..USB sign shows..a smile on my face...puh!
4) Withought wasting a second I flashed the win6.1rom from my pc
5) Phone goes off ready 4 restart..I put the batt back, waits for it to charge for some minutes and startet the phone..walla...there it goes.
Hope this helps someone