Develop Bugs

Unable to boot up after upgrade ROM to WM6

I follow instruction in http://forum.xda-developers.com/showthread.php?t=313486 but after hardreset.
My p800w is stuck in T-Mobile logo and version number. It can't continue booting up to windows mobile.
Question: How to flash ROM without ActiveSync?
How to recovery my Artemis?
Welcome any advice,
Thanks in advance.

Yea me to, mine is now a brick after that upgrade? No active sync connection possible and all I get now is the blue O2 start screen after the hard reset with the red writing and numbers in the top left hand corner..
Phone is an UK XDA Orbit
IPL 1.25.0001
SPL 1.11.0000
GSM 02.67.90
OS 3.4.0.0
HELP!!!!!!!

yeah, I had the same problem and have created a thread for it already. unfortunately I got no useful replies, and it seems that I am stuck waiting for an official o2 ROM so that I can recover my Orbit.

It seems there is a way to un brick our phones I just need to get my phone bootted into bootlader mode which no one seems to say how to do??
Can anyone help how I can boot my Orbit , like what combo of keys I need to press to boot it into bootloader mode then XP will see it at a driver level apparently Active Sync still won;t but I will be able to run some German ROM update with the ROM file replaced with the other ones and it may come back to life..
Help how can I boot my phoen in bootloader mode???

motomob said:
It seems there is a way to un brick our phones I just need to get my phone bootted into bootlader mode which no one seems to say how to do??
Can anyone help how I can boot my Orbit , like what combo of keys I need to press to boot it into bootloader mode then XP will see it at a driver level apparently Active Sync still won;t but I will be able to run some German ROM update with the ROM file replaced with the other ones and it may come back to life..
Help how can I boot my phoen in bootloader mode???
Click to expand...
Click to collapse
I read in here that you hold the voice button and soft reset.

Decaf said:
I read in here that you hold the voice button and soft reset.
Click to expand...
Click to collapse
Correct and use mtty
Already see in the forum ....

Thanks guys and apologies for the spelling..I ran the Artemis_USPL before I tried upgrading to WM6 and again have been able to run it after with my new brick now with the phone in bootloader mode but still when I try and run the german ROM update a) it will only work with the german file which freezes @ 3%? This seems to be a known problem reading around and b )when I replace it with the smaller ROM file, 54MB the german one is 66MB, I originally tried to use it doesn't read the ROM file or the update utility doesn't want to read it. I reckon I might be able to get it back if I can get one of the ROM update utilities to read a good ROm file and send it to the phone.
I can;t find this MTTY program to sniff the USB port and return the code of if the USPL util wokred as I think that could be key to all of this.
Can anyone post a quick how to here for
1) install MTTY from somewhere
2) what command to run agaist the phoen to see if the USPL util worked and what values I should be looking for
3) another WM6 ROM version (that the update utils can read) download location I can download from to try and send to the phone using the German update util
Not asking for much am I but I desperately need my phone back WM5 or 6 in the next day or so so really can't send it off.
Thanks

Error message I recive at the 3% stage when using the German ROM and english update util.

use the file attach and read that :
http://forum.xda-developers.com/showthread.php?t=285112

Thanks but I'm not that cleud up on what commands I'm meant to be sending. It works in Bootloader mode I ge a response from the phone by send it a command. But even if I get a response telling me what the CID status is its not much help as I think ti shoudl have tekane BEBEs ROM by now as I've got the german ROMUpdateUtility sending that 54,272KB file to the phone but it stops after 3%. What are my options?

motomob said:
But even if I get a response telling me what the CID status is its not much help as I think
Click to expand...
Click to collapse
That's right. On older models MTTY was quite useful, but not on the Artemis. You cannot use it to read the CID status anyway. If you are not sure about the status, run the USPL tool, just to make sure.

I've already re run the USPL ROMUpdateUtility and it completes 100% okay in bootloader mode. But after I hard reset and then try and flash the WM6 BEBE ROM or any ROM German etc back onto it it either fails with the error code I posted up earlier or gets to 3% and fails.
What are my options at this stage? Does anyone have a link to another ROM I can try like the original WM5 O2 ROM or any other WM6 ROm that might work. I'm willing to give them all a try as it's just a useless phone right now and I haven;t sent it off as 1) I need it before the weekend and 2) As I can flash some ROMs with the USPL and others have done this no problem I really feel there must be a solution as I can still falsh the phone.

What can I say RTFM... I did it all right and I didn't have a brick, I missed out one small detail... loading on the ROM with the extended ROM. All now running and it does seem a little faster than WM5.
Thank you to all those that tried to help out. To the others that are still having probs.. Don't try and run the update in the middle of a busy day in the office whilst trying to manage 100 other things meaning you are probably missing out a line like me...
One question though how do I get back my O2 power and storage meters on the today screen back as I liked them and the WiFi seems to have a bug where when it is enabled and you click on the WiFi symbol up the top it only allows you to switch it on, when it is already on.. so you have to open up the COMM manager to switch it off.

So how did you fix it exactly? I have read this thread thoroughly and can't find out what you did!

ERROR[206] occurs while trying to update ROM to WM6
While tring to update ROM to WM6 on O2 XDA Orbit i encounter ERROR[206].
I wanted to attach the screen shot but dont know how to do that, but anyway what i am doing is i attached my pda to my pc via activesync using supplied usb cord. Everything goes well till i reach a screen where it says "You are now ready to update your ROM image...." and once i click next a progress bar apperas and my pda shuts and activesync exit's automatically and my pda tries to restart with RBG band and some text:RUU, IPL 1.25.0001, SPL 1.25.0000 and USB. And thats it after few seconds or a min i get the ERROR[206] and my pda hangs.
I dont know why Activesysn shutsdown ???
Just an additional in i want to tell that without installing activesync i am not able to connect/pair my pda with my pc. So do i need to install the drivers and then try or it doen't matter cause once i install Active sync i can connect the device.
Please help me with this....
Thanks

unable to load bootloader!!!!!!!!!!!!
HELP!!!!!!!!
I have HTC3300, tried to update rom, now its bricked. I tried to start bootloader by pressing the voicebutton and softreset but loads in t-mobile screen and hangs, im unable to start the bootloader.
Is this end of story or are there any other options to get the bootloader to start????
please help

Bootloader
I had a problem with my phone loaded touch flow 4 and cid unlocking, everything was fine then after a while it froze at boot up.
I look put the battery and did a hard reset, put it into bootloadeder mode, reflashed with a t-mobile rom does not need to be cid unlocked to do that.
Once origonal rom was working, cid unlock again, flashed back to touchflow 4.0 - sorted

Where did you got an tmobile rom from can you tell me. Mine is also freezing on booting almost once every day or so after I've upgraded to 4.0

MAJOR problem loading WM6

I was in the middle of upgrading my version of WM6 and i got unplugged and now it wont resume and the phone is stuck at the loading screen that says "HTC" mobile.htc.com
what the heck do i do? it wont budge.. it wont sync with active sync, it wont resume.. i'm flipping out.

did you try get your phone in the tri color bootloader screen and then running the Hard SPL program again?

god, I'm gonna admit, I have no idea what any of that stuff is. I know the tricolor screen, I dont know what an SPL is.. a friend of mine usually sends me the upgrades for my programs and i just follow his instructions, but as i was loading the new version it got unplugged and when i tried to follow the restore options it wouldnt restore the upgrade.. so I've learned the term is bricking.
Activesync won't reconnect the phone.. it tries, then doesnt recognize the device.. so even if i try to downgrade to 1.04, it wont work because it wont sync with the damn computer.. I hard reset, i soft reset, i got it to the tricolor screen, i tried all the stuff in the hermes upgrade problems thread, but i dont know wtf i'm doing. the file mtty.exe wont work.. it just freezes at whatever screen i happen to get it to, be it the tricolor or the HTC screen.
please, someone help me out.. I apologize in advance for not being as savvy as everyone else, but I need some advice here.

Go the tri colour screen
press both soft buttons (the ones that interact with the screen) and insert the stylus and reset.
from here you can make an hard reset. Whenever my phone hangs (or whatever) I use this way BUT i use the cancel button (X) and the phone simply restarts fine

Did u hard SPL your device?

Costanza said:
press both soft buttons (the ones that interact with the screen) and insert the stylus and reset.
from here you can make an hard reset. Whenever my phone hangs (or whatever) I use this way BUT i use the cancel button (X) and the phone simply restarts fine
Click to expand...
Click to collapse
I hard reset, I soft reset, it freezes either way. The only way the computer recognizes the phone is when I get the tricolor screen but active sync wont connect to FINISH loading the upgrade.

antonlim1999 said:
Did u hard SPL your device?
Click to expand...
Click to collapse
I cant because it wont connect to activesync to install anything else.. i cant dongrade, upgrade, nothing! i cant get to version 1.04 from the 1.06 im running because activesync wont recognize my phone.

I think antonlim1999 mean, did you hard-spl before you even upgrade to wm06 or not ?

sg10 said:
I think antonlim1999 mean, did you hard-spl before you even upgrade to wm06 or not ?
Click to expand...
Click to collapse
I already had wm6, i was just getting a better version that didnt have as many bugs.. I began loading it, it got to 45%, then the cat knocked the cable out and it got messed up.. I dont believe it was hard-spl beforehand.. im gonna go with no.

Could you try to SPL in the tri colour mode (as you have contact between the unit and the PC)?
Link below has all (almost) info
http://wiki.xda-developers.com/index.php?pagename=HTC_Hermes

A warning to those with an aversion to reading
This is a warning to those who don't really know what they're doing. Upgrading a ROM on a WinMo device is something that should only be done when you know what you're doing.
Hope your device can upgrade well, but please, take the time to actually read the wiki and forum before upgrading again, for your own wallets sake.

hiddenconcepts said:
I was in the middle of upgrading my version of WM6 and i got unplugged and now it wont resume and the phone is stuck at the loading screen that says "HTC" mobile.htc.com
what the heck do i do? it wont budge.. it wont sync with active sync, it wont resume.. i'm flipping out.
Click to expand...
Click to collapse
You are not even in the right forum, you'll get better help elsewhere.
Start reading here: http://forum.xda-developers.com/showthread.php?t=286755
Hard SPL thread: http://forum.xda-developers.com/showthread.php?t=296722

philjohn said:
This is a warning to those who don't really know what they're doing. Upgrading a ROM on a WinMo device is something that should only be done when you know what you're doing.
Hope your device can upgrade well, but please, take the time to actually read the wiki and forum before upgrading again, for your own wallets sake.
Click to expand...
Click to collapse
thanks, but I've upgraded before to other versions without a problem and I know that pulling the plug out is a bad idea.. the cat jumped up and ripped it out causing it to brick.

What all the smart arses on this site should be telling you is that you don't need activesync to run the upgrade - it will work just fine from the tri-colour screen.
First off, when you get your phone into the tri-colour screen, check the SPL version - if it isn't 2.10 olipro, the first thing you need to do is read the vanx guide's (link in my sig) and get hard SPL 2.10 olipro on there ASAP - this will prevent you from bricking your phone.
If it is already 2.10 olipro, then breathe a sigh of relief as everthing is OK - just put it into the tri-colour screen and run the upgrade again - it should start again with out a problem.
Cheers,
Smiffy.

HTC Diamond bricked?

i have flashed my diamond with the official htc rom
im on 1.40 olinex, now i can only access boot mode.
sometimes if i leave the phone without a battery for like 2 hours, when i turn it on i see the "touch diamond" logo, if i leave the battery for a whole day i see the windows mobile loading screen, but then suddenly the phone turns off
plz if you have any idea about this problem help me

If you can acces bootloader, then your diamond isn't bricked.
Try the unsigned version of olinex' hard-SPL and flash the ROM again.
Good luck!

hey ElCondor, im on 1.40 olinex, i cant flash it because it is protected
how can i flash the unsigned 1.40 olinex one?

Here is a link to the unsigned hard-spl.
Make sure you download "Unsigned-Hard-SPL-Diamond-OliNex.zip".
Follow the instructions:
1) Download, extract to an empty folder.
2) Run RomUpdateUtility.exe, Have Phone Synced with PC (go into bootloader, connect your cable, then the word "serial" in bootloader will change into "USB".
3) follow steps, check device for prompts after PC shows loading bar. it should go to black screen now.
4) SPL flashes, device automatically reboots, job done.
5) to confirm you got it installed, go into bootloader mode (volume down + reset, i.e. press volume down button and reset then keep holding the volume down key until you see tricolour screen) and verify the screen shows 1.40.OliNex.
note: you will not see the SPL version during normal boot, that is the OS version, not SPL!
Installing this will hard-reset your device.
Best Regards,
ElCondor

when i flashed the unsigned 1.40 olinex, the device rebooted
windows mobile is preparing your phone for first use
htc logo
phone went off :S
will try flashing rom again

flashed ROM again, now it wont boot up no htc diamond logo no nothing
i can access boot mode (1.40 olinex unsigned now i guess)
is there no way i can boot the rom? what seems to be my problem?

mzaouar said:
flashed ROM again, now it wont boot up no htc diamond logo no nothing
i can access boot mode (1.40 olinex unsigned now i guess)
is there no way i can boot the rom? what seems to be my problem?
Click to expand...
Click to collapse
Hi
If you can access the bootloader then your device is not bricked. Therefore download a rom of your choice then connect to the usb when on the bootloader then use a Diamond custom RUU (normally come with the rom) follow the steps. After rom updated make a hard reset. I hope it will run ok.
Looks your symtons are showing like your rom corrupted.
Good luck

i am flashing this ROM
RUU_Diamond_HTC_Europe_1.93.401.2_Radio_Signed_Diamond_52.29.25.12_1.00.25.05_Ship
the newest one i downloaded from htc. com is giving me rom update error
would you recommend a good rom for my phone?

after flashing and reflashing and hard resetting with the ROM showed above
still cant boot in ROM mode, only in boot mode
el condor sabes, anything ???
should i flash with a new rom, and if yes with which?
(diam100 olinex 1.40 unsigned)

Perhaps try a custom rom?
I found when flashing to an official rom from a different provider (my phones telstra and was flashing 3) I had issues with the rom booting and had to follow a post on here somewhere to get it working, however When I had this problem I could still flash any custom rom with no issues.
Unless its for warrenty purposes then its probably not worth flashing the "original" perhaps flash A.Z.T.O.R. = Alpha Zero Tweaked Official Roms which are close to the original but with benifits of being modded for faster speed etc.
Anyways Im no pro but I know what you are going through and I am trying to find the link to the fix to your problem as I also had the problem. But recommend trying a custom rom to confirm the problem is the same as mine.
For the record now I do not use official roms anymore, with WM6.5 running well for the most part on the diamond its a great step backwards when you revisited 6.1

flashed to SwiftBL-WWE-Diamond-v7.5-Full-16MbPP
still same problem can only go to boot mode
i am feeling there is no solution to my problem ?
is the phone bricked? :S

If you haven't done yet, flash the hard-spl I posted. Just do it, re-instal the hard-spl! Then, flash another ROM, maybe (as said before) your rom is corrupted.
The problem here is, that you first installed the unsigned hard-spl, and then flashed a corrupt rom. In that way, the hard-spl can be damaged too, so flash the hard-spl again and flash another rom should work.
Good luck!

I did :S but to no avail, I will do it again fingers crossed :S !
update: weird, everytime after i flash the hardspl unsigned, it boots up, i can see the "touch diamond" logo
windows mobile booted.. preparing your device..
update 2: windows mobile booted, installing everything
omgomg it looks it might work this time, fingers still crossed !!
el condor !! haha fingers crossed
update 3 :S : windows mobile installed properly, phone rebooted, went again and opened it, then i heard a sound from the speaker and the phone turned off :S
it must work what could the problem be now? last step !

Okay try a hard-reset, maybe that works.
If not, then flash hard-spl again, then hard-reset, then flash another ROM. Then hard reset. Then try again if it boots.
Is your battery enough charged? That could also be a reason.

did not work, wont even boot up
when i said if i leave battery out and such, I thought it might be hardware/heat related
http://www.htcwiki.com/thread/2069847/HTC+Diamond+-+Severe+Crashing+Problem,+maybe+heat+related
could this be it? will i have to send my phone for repairs?
because maybe when WinMo was loaded, the phone started to heat up and it shut down
so basically my solution is not a software fix??

If none of the tips worked, and you have the same problems as described in the site you linked, then you probably have to send it back.
One thing you could do: Try if the other hard-spls (1.37 and 1.93 unsigned) are working for you.
I'm sorry for you, maybe someone more skilled than me (like cmonex or olipro) knows how to solve your problem.

it's alright :S i thank you for all the help you have offered !
( it is customizing right now) but i expect it to reboot anytime now

worked, 5 minutes into winmo it restarts

mzaouar said:
worked, 5 minutes into winmo it restarts
Click to expand...
Click to collapse
oh,does it worked?how can you get it work?Please tell me....my diamond could only get in the bootloader yet....

mzaouar said:
worked, 5 minutes into winmo it restarts
Click to expand...
Click to collapse
OK good to hear that, if you have any more questions in future, just ask!
Glad to be of some help
msvb007 said:
oh,does it worked?how can you get it work?Please tell me....my diamond could only get in the bootloader yet....
Click to expand...
Click to collapse
Ive sent you a pm, there's no need to use this thread for your questions because the problem in this thread is solved.
So take a look at your pm!

Dead Diamond

I've got a little problem :/ few flashes ago i started experiencing problems with my diamond. some times when it freezes and i reboot it it was restoring itself to defaults. now i installed new radio and new rom. it was ok for 3 days. now it only boot itself to screen where it says "touch diamond" and numbers about rom. my pc don't see my phone, vol. down + reboot dont work :/ help pls

try to enter into bootloader mode and flash a new rom

DilosPL said:
I've got a little problem :/ few flashes ago i started experiencing problems with my diamond. some times when it freezes and i reboot it it was restoring itself to defaults. now i installed new radio and new rom. it was ok for 3 days. now it only boot itself to screen where it says "touch diamond" and numbers about rom. my pc don't see my phone, vol. down + reboot dont work :/ help pls
Click to expand...
Click to collapse
Might be a problem with your radio. Can you provide more details about your unit, ie:
What version is your SPL/HardSPL?
What version is your radio?
What ROM are you using (OS, etc)?

Did you try to remove the battery for a lot of time?

I have two solutions
DilosPL said:
I've got a little problem :/ few flashes ago i started experiencing problems with my diamond. some times when it freezes and i reboot it it was restoring itself to defaults. now i installed new radio and new rom. it was ok for 3 days. now it only boot itself to screen where it says "touch diamond" and numbers about rom. my pc don't see my phone, vol. down + reboot dont work :/ help pls
Click to expand...
Click to collapse
I also had this problem, and i have two solutions, maybe can help you :
1. On your phone: simultaneously press the volume down and reset to get into boot mode.
Once you have managed this, follow the instructions on the screen of your computers with installation of rom.
2. Possibly you do not succeed the first step, obtain a version of HardSPL Diamond, .nbh or ROMUpdateUtility.exe, and running, with the phone connected to PC and in mod boot loader.
IMPORTANT I recommend :
" Try to get HardSPL-1.24 " , ( versions of HardSPL which are in atachament I have not ever installed on the my HTC Touch Diamond, because already have the HardSPL-1.24 on my phone )
Should work, good luck and more attention next time.

THX!! i reinstalled my hardspl to 1.30 and then i was able to reinstall my rom ^^ and it works

nope :/ still restoring to factory after freeze and reset :/

DilosPL said:
nope :/ still restoring to factory after freeze and reset :/
Click to expand...
Click to collapse
use MTTY then flash the Hard SPL 1.40 then flash the rom you want

Yep random soft/hard resetting is a sympton of MTTY necessity!

Touch Diamond won't boot ! ! !

I installed a HardSPL 1.40 Olinex. Then Custom RUU 23125 from here. I installed a wm 6.5 (i gues so). I run the OS and i began to personalize my new OS. The system buged and crashed. After reboot (by taking out the battery) the OS wouldn't start. I tried hard reset, but nothing. I am sorry for the very bad english, but i need help urgently ! ! ! I have the phone from 4 days If i only knew what will happen.... Thank you!

atomheart said:
I installed a HardSPL 1.40 Olinex. Then Custom RUU 23125 from here. I installed a wm 6.5 (i gues so). I run the OS and i began to personalize my new OS. The system buged and crashed. After reboot (by taking out the battery) the OS wouldn't start. I tried hard reset, but nothing. I am sorry for the very bad english, but i need help urgently ! ! ! I have the phone from 4 days If i only knew what will happen.... Thank you!
Click to expand...
Click to collapse
I would suggest you by following solution
1.Boot from MTTY way
2.Try SPL 1.93
3.Change your battery--i experienced once when i flash a new ROM and my diamond stuck on "TOUCH DIAMOND-the first screen" and then keep reboot. Then i change my battery, it boot just like nomal.
Good Luck.

ku9911 said:
I would suggest you by following solution
1.Boot from MTTY way
2.Try SPL 1.93
3.Change your battery--i experienced once when i flash a new ROM and my diamond stuck on "TOUCH DIAMOND-the first screen" and then keep reboot. Then i change my battery, it boot just like nomal.
Good Luck.
Click to expand...
Click to collapse
OK, so i now can boot the OS, after perssing turn on + down + middle key and format. But every time it stop working at the moment when i have to tap for the last time the screen to let me in. I press, press, press... Press with the finger and with the styler but nothing happened and i have to reboot and do all this shi*s again. What is MTTY and how to install SPL 1.93 without OS on the phone? Thanx !

atomheart said:
OK, so i now can boot the OS, after perssing turn on + down + middle key and format. But every time it stop working at the moment when i have to tap for the last time the screen to let me in. I press, press, press... Press with the finger and with the styler but nothing happened and i have to reboot and do all this shi*s again. What is MTTY and how to install SPL 1.93 without OS on the phone? Thanx !
Click to expand...
Click to collapse
no need to get back to 1.39 .. olinex 1.40 works fine. maybe just the rom is faulty when after reset+vol down+enter does the same error!
get onto boot loder (reset + vol down) when you get the "serial" label, plug in the usb, do the task 29 to format the phone, and get some other rom, and flash it with provided exe file.

atomheart said:
OK, so i now can boot the OS, after perssing turn on + down + middle key and format. But every time it stop working at the moment when i have to tap for the last time the screen to let me in. I press, press, press... Press with the finger and with the styler but nothing happened and i have to reboot and do all this shi*s again. What is MTTY and how to install SPL 1.93 without OS on the phone? Thanx !
Click to expand...
Click to collapse
Are you using Atlas rom? or what? This rom has a bug in this moment of installation that sounds like your behavior...
I have several problems with 6.5/6.5.x newer builds before I switch to hardSPL 1.93 developer edition. This hardSPL could be installed to the phone also in the situation when no active sync connection is available. Simply run "installer" and go through the process as usual, you will see that it works...
Mbiba

mbiba said:
Are you using Atlas rom? or what? This rom has a bug in this moment of installation that sounds like your behavior...
I have several problems with 6.5/6.5.x newer builds before I switch to hardSPL 1.93 developer edition. This hardSPL could be installed to the phone also in the situation when no active sync connection is available. Simply run "installer" and go through the process as usual, you will see that it works...
Mbiba
Click to expand...
Click to collapse
I am with Energy ROM 2.xxxx. I' ll try this right now.

260 error
it ' s give me error 206 (telephone not connected). How to instal whatever without a USB connection and ActiveSync? It doesn' t work> It' s stuck now on Starting Windows screen: Preparing for first use....."

Flash a stock rom with stock spl from bootloader (press soft reset then volume down ) then re try with hard spl and put another rom like energy rom that works for sure (at least for me)

atomheart said:
OK, so i now can boot the OS, after perssing turn on + down + middle key and format. But every time it stop working at the moment when i have to tap for the last time the screen to let me in. I press, press, press... Press with the finger and with the styler but nothing happened and i have to reboot and do all this shi*s again. What is MTTY and how to install SPL 1.93 without OS on the phone? Thanx !
Click to expand...
Click to collapse
seems u did not read much before flashing. I guess you can easily solve the problem following Post2. You are doing Hard reset (reset+down+middle). It would not solve the problem. For new flash or mitty you have to go to boot loader screen (reset+down vol. key) (not the middle key). Also Active sync menu: file->connection settings, deselect 'Allow USB connection'.... then start flashing new rom (more details see Mitty or flash thread):
http://forum.xda-developers.com/showthread.php?t=540290
http://forum.xda-developers.com/showthread.php?t=416211
in simple english,
MITTY: for formatting ROM so that no old data will mess up with new rom (not always required but solves many wiered problems)
I once faced such problem , Mitty (once) and flashing rom (twice) solved the problem

HELICOPTER88 said:
Flash a stock rom with stock spl from bootloader (press soft reset then volume down ) then re try with hard spl and put another rom like energy rom that works for sure (at least for me)
Click to expand...
Click to collapse
Thank you man. It works now. I installed this rom: RUU_Diamond_HTC_Europe_1.93.401.2_Radio_Signed_Diamond_52.29.25.12_1.00.25.05_Ship.exe.
Can you, or anybody give me some advice about which Rom should I install, to install wm 6.5 for my phone. Is there some "light" ROM, or something, for wm6.5 (working).?

atomheart said:
Thank you man. It works now. I installed this rom: RUU_Diamond_HTC_Europe_1.93.401.2_Radio_Signed_Diamond_52.29.25.12_1.00.25.05_Ship.exe.
Can you, or anybody give me some advice about which Rom should I install, to install wm 6.5 for my phone. Is there some "light" ROM, or something, for wm6.5 (working).?
Click to expand...
Click to collapse
I think currently the best is ralphusion J with only few bugs and issues.
Mbiba