Develop Bugs

DOPOD 900 dead after upgrade

My DOPD - bought in China was running a chinese version of WM5.0 and I wanted to install a english version.
After upgrading my DOPOD 900 with the upgrade : Universal_Upgrade_v1.30.68_radio_1.09.0.zip I have problem.
It is really DEAD. soft reset does nothing and a hard reset only gives the option of "0" and "X" which do nothing.
the USB is no longer recognised and nothing seems to want to communicate with the Dopod. It seems the USB loader program is no longer running on the Dopod.
Has anybody any idea how I can attach to the device an install a new bootloader, or something.

I had the same issue and I have a solution. But, let me tell you my process that got me where you are.
I tried performing the update using the No_ID (or whatever) method and kept getting errors. I rebooted my PC and changed the Operator ID using the HTC64 Extended ROM Tool.
After this, I was able to use the typical installer. The flash went fine and I hard reset as instructed. From that point on, I had your exact problem.
A dead screen. I was able to redo the hard reset after pulling the battery but I would just end up with the dead (blank) screen again. ONCE, I did get it into boot loader mode where I could actually read the screen. But, of course I reset and again had a dead screen.
My solution was to revert back to a true O2 ROM. Even though I couldn't see the screen (still can't), the ROM update is proceeding as I type this. I'm at 44% of the radio ROM installed.
Hope this gives you hope!

Well, good news. I just finished the ROM update and I'm looking at the O2 boot image.
Is there any indication that the QTek ROM looks for the Carrier info to be QTek or it will fail once installed? Just wondering why I had this problem.

ARG! Reflashing with QTek ROM did the same thing. :evil:
Blank screen and all.

check 2 things
uncheck usb from active sync
hardreset after upgrade has been completed
just do the upgrade again and it should come alive again

Thanks and another question
Well thanks for the hope. but I have tried this already with no luck, however after this message I will try again. My biggest problem is that I cant regain communication over the usb.
I would like to know how your system behaved when you plugged in your apparantely dead device. My system just says device un recognised and I cant begin a download with or without active sync.
So I cant get another rom image to download.
regards
Nick

dolebole said:
check 2 things
uncheck usb from active sync
hardreset after upgrade has been completed
just do the upgrade again and it should come alive again
Click to expand...
Click to collapse
This was the first thing I did.
The problem is that I cannot get any communication over the USB.
The device is unrecognised on USB and after starting any ROM download it just timesout after "checking information from device" message .
Ever seen a dead USB interface like this ?
The USB PnP mgr sees the hardware but cannot establish the device type !!
Nick

@mobinick: You and I have the same situation.
I have 2 Universal dead like this. 1 Exec and 1 Jasjar.
Both dead, blank screen, can not enter bootloader, can not connect with PC. PC can not recognize the driver usb of the device.
I opened the phone and found that logically everything is so so. There is no clue about hardware.
So I think: the address of the bootloader with device ID maybe unlucky damaged.
Who can fix this problem pls share us some experience.
Thanksss

ta_mobile said:
@mobinick: You and I have the same situation.
I have 2 Universal dead like this. 1 Exec and 1 Jasjar.
Both dead, blank screen, can not enter bootloader, can not connect with PC. PC can not recognize the driver usb of the device.
I opened the phone and found that logically everything is so so. There is no clue about hardware.
So I think: the address of the bootloader with device ID maybe unlucky damaged.
Who can fix this problem pls share us some experience.
Thanksss
Click to expand...
Click to collapse
Why don't you guys take it to your respective service centres and get it fixed?
Even if you have to pay something, it will certainly be better than these bricks occupying table space.

Have you tried going back to an original O2 ROM? I went to 1.13.139 WWE and all is fine now.

Just to share my experience with you guys here:
I posted my problem way back during the Radio Upgrade from 1.04 to 1.06. My Dopod 900 got stuck on the splashscreen. I couldn't get my device to pass the splashscreen even after upgrading/downgrading the radio ROM back and forth two times.
Finally, I just forced my device into bootloader mode (Backlight+Reset+Power). Even after doing this, the dopod screen was completely blank (no indication of serial/usb letter on the screen). I downloaded the official O2 exec ROM and plug my device (in bootloader mode) back to the USB port. It said unrecognized port on my PC. Despite that, I reflashed my Dopod back with the NoID tool the complete O2 ROM (Radio, Main ROM & The extended). Once completed, my device regained its consciousness.
I managed to flashed back the 1.06 radio after that. And has since been upgraded 4 times (two i-mate, one Orange and the latest QTek ROM) with no problem whatsoever.

I had the exact same problem as you to guys, i tried to update it, and it wouldn't budge...
It constantly, without fail timed out... I tried everything...
As my hope started to wain, i gave it one last shot...
I took out everything, sim and sd and battery, then connect the battery back and from the bootloader menu, connected it to the pc, with usb cable...
Finally it worked!! Like normal, i was able to load any and all rom and radio updates...
Wouldn't work, from the normal working screen (which was working for a while, i later tested this out, and found out ) and also wouldn't work, from the bootloader (power+backlight+reset) with sim+flash in there....
Hope you guys have some luck.. I htink you should, because i was in the exact same boots as you guys...

It worked for me
My O2 Exec did exactly the same thing, and I spent (on and off) 24 hours trying to get the damn thing to go again - wouldnt charge either....
I too finally took out everything, SIM and sd and battery, then connect the battery back and from the bootloader menu (which I only found about from this site), connected it to the pc, with usb cable...
It worked as well - bloody brilliant. I now have the latest 02Exec Upgrade (Version 1.30.162 AKU2 Release) and all is great.
Cant believe that 2 days after logging email with O2 site, they have not responded...
Would almost kiss you guys.....

Solution for getting stuck in bootloader
http://wiki.xda-developers.com/index.php?pagename=Instructions for those stuck on Boot Screen

Seriously need help with my SPV M5000 upgrading issue. Massive Problem!! Please Help!

Hello, i upgraded my spv m5000 via orange site. during the upgrade the setup gave me an error and went off. and now my screen of the spv m5000 is stuck on the installation screen. i.e. saying Serial on top of the screen and V1.00 at the buttom. ive tryed resetting the phone but nothing happens.
and now my battery is dead and it only charges a bit and the same screen comes up
Ive contacted orange about a month ago now and they dont know what to do as they dont understand the issue also took to the shop no help recieved.
please tell me what i have to do to get my phone up and running.
thanks

skemeone said:
Hello, i upgraded my spv m5000 via orange site. during the upgrade the setup gave me an error and went off. and now my screen of the spv m5000 is stuck on the installation screen. i.e. saying Serial on top of the screen and V1.00 at the buttom. ive tryed resetting the phone but nothing happens.
and now my battery is dead and it only charges a bit and the same screen comes up
Ive contacted orange about a month ago now and they dont know what to do as they dont understand the issue also took to the shop no help recieved.
please tell me what i have to do to get my phone up and running.
thanks
Click to expand...
Click to collapse
try racharge you batery using external charger... than put your device to boot loader mode (serial on top & bootloader version bottom) than try to flash again
cheers
indra9110

yes its already on boot loader mode and i am unable to go off it. also i am unable to charge the battery with the external adapter.
Is there any software that can be used to flash without using active sync cause it has developed its own usb connection.
its always saying serial on top and V1.00 at the buttom
thanks for quick reply.

skemeone said:
yes its already on boot loader mode and i am unable to go off it. also i am unable to charge the battery with the external adapter.
Is there any software that can be used to flash without using active sync cause it has developed its own usb connection.
its always saying serial on top and V1.00 at the buttom
thanks for quick reply.
Click to expand...
Click to collapse
as I say ... just flashing again on bootloader mode ...
cheers
indra9110

with what software
please tell me
cheers

i have retryed my upgrade software but as i do not have active sync connection i am unable to install via software. please let me know which software you are taking about.

You dont need active sync for upgrading your ROM. When the device is in bootloader (and yours obviously is ;-), connect it to a pc through the usb cable and run the upgrade utility from the orange site again. Sometimes it takes two or three times.

hello, THANKS A LOT. YOU HAVE EXPLAINED TO ME EVERYTHING THAT EVEN THE COMPANY ORANGE COULD NOT DO..,
Your da true expert in this device.
Thank you every much.

all of you that have reply thank you very much

Unable to boot up after upgrade ROM to WM6

I follow instruction in http://forum.xda-developers.com/showthread.php?t=313486 but after hardreset.
My p800w is stuck in T-Mobile logo and version number. It can't continue booting up to windows mobile.
Question: How to flash ROM without ActiveSync?
How to recovery my Artemis?
Welcome any advice,
Thanks in advance.

Yea me to, mine is now a brick after that upgrade? No active sync connection possible and all I get now is the blue O2 start screen after the hard reset with the red writing and numbers in the top left hand corner..
Phone is an UK XDA Orbit
IPL 1.25.0001
SPL 1.11.0000
GSM 02.67.90
OS 3.4.0.0
HELP!!!!!!!

yeah, I had the same problem and have created a thread for it already. unfortunately I got no useful replies, and it seems that I am stuck waiting for an official o2 ROM so that I can recover my Orbit.

It seems there is a way to un brick our phones I just need to get my phone bootted into bootlader mode which no one seems to say how to do??
Can anyone help how I can boot my Orbit , like what combo of keys I need to press to boot it into bootloader mode then XP will see it at a driver level apparently Active Sync still won;t but I will be able to run some German ROM update with the ROM file replaced with the other ones and it may come back to life..
Help how can I boot my phoen in bootloader mode???

motomob said:
It seems there is a way to un brick our phones I just need to get my phone bootted into bootlader mode which no one seems to say how to do??
Can anyone help how I can boot my Orbit , like what combo of keys I need to press to boot it into bootloader mode then XP will see it at a driver level apparently Active Sync still won;t but I will be able to run some German ROM update with the ROM file replaced with the other ones and it may come back to life..
Help how can I boot my phoen in bootloader mode???
Click to expand...
Click to collapse
I read in here that you hold the voice button and soft reset.

Decaf said:
I read in here that you hold the voice button and soft reset.
Click to expand...
Click to collapse
Correct and use mtty
Already see in the forum ....

Thanks guys and apologies for the spelling..I ran the Artemis_USPL before I tried upgrading to WM6 and again have been able to run it after with my new brick now with the phone in bootloader mode but still when I try and run the german ROM update a) it will only work with the german file which freezes @ 3%? This seems to be a known problem reading around and b )when I replace it with the smaller ROM file, 54MB the german one is 66MB, I originally tried to use it doesn't read the ROM file or the update utility doesn't want to read it. I reckon I might be able to get it back if I can get one of the ROM update utilities to read a good ROm file and send it to the phone.
I can;t find this MTTY program to sniff the USB port and return the code of if the USPL util wokred as I think that could be key to all of this.
Can anyone post a quick how to here for
1) install MTTY from somewhere
2) what command to run agaist the phoen to see if the USPL util worked and what values I should be looking for
3) another WM6 ROM version (that the update utils can read) download location I can download from to try and send to the phone using the German update util
Not asking for much am I but I desperately need my phone back WM5 or 6 in the next day or so so really can't send it off.
Thanks

Error message I recive at the 3% stage when using the German ROM and english update util.

use the file attach and read that :
http://forum.xda-developers.com/showthread.php?t=285112

Thanks but I'm not that cleud up on what commands I'm meant to be sending. It works in Bootloader mode I ge a response from the phone by send it a command. But even if I get a response telling me what the CID status is its not much help as I think ti shoudl have tekane BEBEs ROM by now as I've got the german ROMUpdateUtility sending that 54,272KB file to the phone but it stops after 3%. What are my options?

motomob said:
But even if I get a response telling me what the CID status is its not much help as I think
Click to expand...
Click to collapse
That's right. On older models MTTY was quite useful, but not on the Artemis. You cannot use it to read the CID status anyway. If you are not sure about the status, run the USPL tool, just to make sure.

I've already re run the USPL ROMUpdateUtility and it completes 100% okay in bootloader mode. But after I hard reset and then try and flash the WM6 BEBE ROM or any ROM German etc back onto it it either fails with the error code I posted up earlier or gets to 3% and fails.
What are my options at this stage? Does anyone have a link to another ROM I can try like the original WM5 O2 ROM or any other WM6 ROm that might work. I'm willing to give them all a try as it's just a useless phone right now and I haven;t sent it off as 1) I need it before the weekend and 2) As I can flash some ROMs with the USPL and others have done this no problem I really feel there must be a solution as I can still falsh the phone.

What can I say RTFM... I did it all right and I didn't have a brick, I missed out one small detail... loading on the ROM with the extended ROM. All now running and it does seem a little faster than WM5.
Thank you to all those that tried to help out. To the others that are still having probs.. Don't try and run the update in the middle of a busy day in the office whilst trying to manage 100 other things meaning you are probably missing out a line like me...
One question though how do I get back my O2 power and storage meters on the today screen back as I liked them and the WiFi seems to have a bug where when it is enabled and you click on the WiFi symbol up the top it only allows you to switch it on, when it is already on.. so you have to open up the COMM manager to switch it off.

So how did you fix it exactly? I have read this thread thoroughly and can't find out what you did!

ERROR[206] occurs while trying to update ROM to WM6
While tring to update ROM to WM6 on O2 XDA Orbit i encounter ERROR[206].
I wanted to attach the screen shot but dont know how to do that, but anyway what i am doing is i attached my pda to my pc via activesync using supplied usb cord. Everything goes well till i reach a screen where it says "You are now ready to update your ROM image...." and once i click next a progress bar apperas and my pda shuts and activesync exit's automatically and my pda tries to restart with RBG band and some text:RUU, IPL 1.25.0001, SPL 1.25.0000 and USB. And thats it after few seconds or a min i get the ERROR[206] and my pda hangs.
I dont know why Activesysn shutsdown ???
Just an additional in i want to tell that without installing activesync i am not able to connect/pair my pda with my pc. So do i need to install the drivers and then try or it doen't matter cause once i install Active sync i can connect the device.
Please help me with this....
Thanks

unable to load bootloader!!!!!!!!!!!!
HELP!!!!!!!!
I have HTC3300, tried to update rom, now its bricked. I tried to start bootloader by pressing the voicebutton and softreset but loads in t-mobile screen and hangs, im unable to start the bootloader.
Is this end of story or are there any other options to get the bootloader to start????
please help

Bootloader
I had a problem with my phone loaded touch flow 4 and cid unlocking, everything was fine then after a while it froze at boot up.
I look put the battery and did a hard reset, put it into bootloadeder mode, reflashed with a t-mobile rom does not need to be cid unlocked to do that.
Once origonal rom was working, cid unlock again, flashed back to touchflow 4.0 - sorted

Where did you got an tmobile rom from can you tell me. Mine is also freezing on booting almost once every day or so after I've upgraded to 4.0

Diamond disconnects during HardSPL update

Hi!
I just got myself a Diamond and im trying to upgrade it. I've read the following tutorial: http://forum.xda-developers.com/showthread.php?t=416211 but the Upgrading to HardSPL doesnt work for me.
When RUU starts updating, the screen on my phonescreen turns black (as it should do) but at the same time it disconnects from the computer and the program. and the phone freezes and i have to take out the battery and reset it. I've tried to repeat it many times, i also changed the power settings and everything.
I have ROM version: 1.93.413.3 SVE and Radio: 1.00.25.05 and Iam trying to update to SwiftBL
Thank You

After your screen turns black, don't flash the SPL yet.
Wait a while till you pc detects the "new" device and installs drivers for it.
If you have still troubles, PM me and we can do it together ...

sum1 help me out plz
oryt mate
sorrry to bother u
erm im on vodafone wiv the vodafone rom thing and i tried puttin a different rom on but it does'nt move past 0%
so i tried that olinex thing and thats not helpd either
stil stays at 0%
any tips? let me knw please
thanks

I have the same problem as stated above..
Screen turns black..
Phone gets disconnected from pc..
Windows is found a new hardware device and is asking for a hardware install..
Hardware Install Fails and phone remains disconnected with a black screen..
WHAT TO DO NOW..?????
I'm afraid of disconnecting my phone, because of the chance ending up with a brick.
Can someone please help me out..???

It happened to me before. For me it was due to the advanced battery setting.
I resolved it by unchecking "turn off device if not used for.." on both battery and external power. Hope this helps.

Nope this does not help..
My phone goes black and dissconnects from the pc and does not reconnect..
Get a connection error from the hardspl update program and have to remove battery to restart phone
Doe anyone have an idea what i am doing wrong..???

I have the same problem. and i have tryed everything...almost:S

Thank you all!
Thank you all for the quick replys,
I've found a solution to my problem.
First of all i unchecked all the battery saving options, and then i went to Settings--> USB to PC--> and uncheck the "Enable advanced network functionality" box, after this the upgrade worked.
Hope this works for you guys 2
Peace

Not working for me here . Htc Diamond from H3G ITA .
I can't get past the black screen . Activesync disconnects and never connects again ... I tried the 2 settings changes proposed here ; I tried waiting almost 10 minutes on the black screen ....
Any other ITA H3G user with the same problem (maybe solved....) or any other user that got away with this huge problem ??

Have you tried pasting SSPL-Manual.exe into Diamond's Windows directory and executing it?

I put it in the root and executed it .... screen went black ... activesync lost connection ....................... after 20 minutes still black screen and nothing happened .
Fortunatly unplug battery and restart got me the pda back working
PS. If I enter the multicolor screen I see as SPL 1.37.0.0 and above it says DIAM100 ..... if any of this info could help to get me more help

don.sina said:
Thank you all for the quick replys,
I've found a solution to my problem.
First of all i unchecked all the battery saving options, and then i went to Settings--> USB to PC--> and uncheck the "Enable advanced network functionality" box, after this the upgrade worked.
Hope this works for you guys 2
Peace
Click to expand...
Click to collapse
Worked like a charm for me
Thanks

grebbo said:
I put it in the root and executed it .... screen went black ... activesync lost connection ....................... after 20 minutes still black screen and nothing happened .
Fortunatly unplug battery and restart got me the pda back working
PS. If I enter the multicolor screen I see as SPL 1.37.0.0 and above it says DIAM100 ..... if any of this info could help to get me more help
Click to expand...
Click to collapse
I believe that is what will happen. I used this method to install 1.40.
After you get the black screen just follow instructions from step 2 in here:
http://modmydiamond.info/index.php?option=com_content&task=view&id=22&Itemid=26
Ignore the activesync turning green part.
The small words in the red box is easy to miss out.

had a similar problem...upgrading to the latest version of .net CF did the trick for me....u might want to check that out (nothing to lose in having an updated version anyway)

Tnx a lot catpuke ... I tried to run the update anyway even with no sync with pc .... it stayed to 0% for a little bit and then jumped to 100% .... now in tricolor shows 1.30 Olinex !
Will move on and try to update radio now !
Tnx again for the help

Help to find/install the right stock spl beause of big problem!

I have posted this in another thread but noone seems to be able to help or have seen this message.
But I hope some of you can give me some kind of help so I can rescue my Touch Diamond.
I really need your help so I cand send my phone to repair on my warranty.
My Diamond is "almost" dead and when it´s connected to the batterycharger, the phone reboots allt the time, but I can access the Bootloader, and it´s the ONLY way I can have contact with my phone.
Power on won´t start my phone and with the batterycharger the text " Touch Diamond" shows upp and then reboots again and again.
But I can enter the Bootloader.
(The last cooked Rom was a beta from udk which worked satisfied. Downloaded and installed on my Diamond in November.)
I have succeded (?) to update the ROM with the official 1.93 Swedish ROM, made by HTC for the Swedish operator 3 via BOOTLOADER beause it seems to install to 100%.
I have no way to check it...had to belive that the 100% indicator was right.
Then I entered the Bootloader (only way for me to get some access to the phone) and tried to install the stock 1.93 spl found in post 20 in this thread:
http://forum.xda-developers.com/showthread.php?t=400411.
Same there: 100% is shown after install, so I thought it should work.
After install, I enter the Bootloader (tricolor) again but the text still says:
Security Unlocked
Diam100 MFG 64M
SPL-1.40 OliNex
MicroP.Diam (LED) v11
PSOC-Diam STAGE_PVT v0x30
I have also tried to install 1.35 spl in that post with no luck!
Do you know why it won´t show the stock spl I tried to install but shows only the hard.spl 1.40 after I tried to change the spl??
Is there another stock SPL I shall install?
I have Sim unlocked my Diamond couples of month ago with the Diamond Unlocker program.
Is my phone a brick now or can I do something so I can use my warranty?
Hope someone can help me!
Thank you very much!

Anyone?

Leave it on charger for an hour and reboot without charger...
Seems to me your battery is knocked down drained I have this too, it just will not start up.
It will start up with charger, but during startup the power is not enough to keep it going, i believe while booting, the chargeprocess is hold for a few seconds. The still empty battery just knocks down phone and -> reboot.

Method of install SPL is diff, then rom/radio.

Riel said:
Leave it on charger for an hour and reboot without charger...
Seems to me your battery is knocked down drained I have this too, it just will not start up.
It will start up with charger, but during startup the power is not enough to keep it going, i believe while booting, the chargeprocess is hold for a few seconds. The still empty battery just knocks down phone and -> reboot.
Click to expand...
Click to collapse
I just tried this and it did´nt help.
When connected to the battery charger, the phone indicates it charge for a couple of seconds, then the start/reboot thing occur again.
But the ring around the D-pad did´nt glow anymore like it does when the phone being charge.
However: I let the phone be connected to the battery charger for 5 hours, then tried to start the phone, but the phone did not react when it had no power source.
But when I have the phone connected to the charger, the phone ony starts with "Touch Diamond" on the screen and then reboots.
During the restarts I can access the bootloader.
I also tried a new and fresh battery from my friends Diamond but same problem occured. The phone wont start.
mondilv said:
Method of install SPL is diff, then rom/radio.
Click to expand...
Click to collapse
I tried to change back to stock SPL - after I had installed stock Rom -by entering the bootloader (the only way I can access my phone) and started the update for SPL. The indicator showed it was updated to 100%.
But when I look at the tricolor screen it still shows I have Olinex 1.40.
Have I made something wrong when I tried to install stock SPL? The installation indicator during the install looked normal.
Can I have problem to install the stock SPL mentioned in post 1, because I have not a WWW- Rom? I had to reinstall the original ROM for the Swedish operator 3.
Really hope someone can help me out so I don´t need to trash my phone into the garbage.