Help Help!!! Recently I try to update my qtek 9000 to Jwrightmc 2.12.8 , once I finished update it start normally till e mail set up, but instead of doing autorunsetup main screen appears, I re download few different Roms and repeat the operation few couple of times but protocol version (42.51.P8) is not changed, then I installed ExtRom.exe the message ok to reboot appears, once it turn on an error message appears that “An unexpected error has occurred in extrom.exe select quit and then restart this program …” I selected details icon at the bottom, this screen says that “ ExtROM.exe Directory not found exception An error message cannot be displayed because an optional resource assembly containing it cannot be found at system.IO._Error.WinIOError()….
Normally I used to get the answer very easily by searching in your forum but this time I couldn’t
If any body knows how I can solve this problem it will be very grateful
Thanking you in advance.
Qtek 9000
Jwrightmc 2.12.08
Protocol V 42.51.P8
Radio 1.15
2GB SD
q9000 said:
Help Help!!! Recently I try to update my qtek 9000 to Jwrightmc 2.12.8 , once I finished update it start normally till e mail set up, but instead of doing autorunsetup main screen appears, I re download few different Roms and repeat the operation few couple of times but protocol version (42.51.P8) is not changed, then I installed ExtRom.exe the message ok to reboot appears, once it turn on an error message appears that “An unexpected error has occurred in extrom.exe select quit and then restart this program …” I selected details icon at the bottom, this screen says that “ ExtROM.exe Directory not found exception An error message cannot be displayed because an optional resource assembly containing it cannot be found at system.IO._Error.WinIOError()….
Normally I used to get the answer very easily by searching in your forum but this time I couldn’t
If any body knows how I can solve this problem it will be very grateful
Thanking you in advance.
Qtek 9000
Jwrightmc 2.12.08
Protocol V 42.51.P8
Radio 1.15
2GB SD
Click to expand...
Click to collapse
Hi welcome to the forum
If you already READ the Wiki and couldn´t find solution, I would recommend to reinstall form cero another ROM, perhaps is a compatibility problem
Good luck
Related
Dear Fellow Forum Members,
Followed instructions as per Xda_II_Upgrade.pdf, during installation got to a section where I got a message saying that the current rom is being erased a task bar was displayed which increase's in percentage as the job goes through. However the job was still at 0% completion when an error message was displayed saying the job had failed and the device needed to be undocked and a soft reset performed and then re-docked and to restart the process again. After performing the undocking of the device and software reset I get a message on the screen serial V1.0.1 when connected to the cradle the message changes to USB 1.01 and I cannot do anything else the unit does not boot into pocketpc, as you can imagine this is very frustrating as I depend on my xda2 to receive and make phone calls I would be very grateful any members know of any way to get around this problem. I must say I am a bit concerned a try and tested xda2 update has led to this problem.
Just run the update .exe file again with the XDA docked and it should just install the update again. It happened to my mate on Saturday with his XDA II and he just ran the program again.
Dave,
done as you said and all went thru fine you are a star thanks mate.
No problems it's good as a newbie to be able to actually help people.
upgrade xda2 rom ver 172187 dead os--connection error
i was trying to upgrde the rom from o2 website when error occured at stage 19% completed asking me to reset the xda2 . when i am trying to reset the xda 2 it does not boot it just shows the o2 screen with red letters of the version and does not even charge. my laptop cannot connect to xda2 and as a result i am unable to upgrade when i tried to run the 172187 .exe again it gives error 101: connection error
please help me out of this? thanks
Hi,
I tried to upgrade my MDAc with the rom from TMobile.
During the upgrade my computer asked for this file "wceusbsh.sys".
At that point the upgrade stopped.
No i only see "USB" and "v1.00" on my screen.
The charger led is red.
When trying to upgrade again, i get ether this message:
Error 120, country id error
or
err no device
I located the file "wceusbsh.sys" but still.
After "checking the information on your device" i get the error.
"Error 120, country id error"
How can i solve this problem.
Greg
You're stuck in bootloader. Did you try to upgrade to an other language?
You can try to hard-reset your device 'power & soft-reset' at the same time to boot your magician.
If it doesn't boot, kick it back in bootloader 'camera & power & soft-reset' at the same time for several seconds, till screen turns black & read 'serial v1.00'. When connected to usb it reads 'usb v1.00'
Now get maupgradeut_noid.exe from the ftp. Unzip your shipped-rom file you downloaded from TMO. Put the maupgradeut_noid.exe in the same folder as the unzipped files like maupgradeut.exe, enterbl.exe etc. Then execute maupgradeut_noid.exe instead of maupgradeut.exe this will give the error 120 once more. Just exit & execute it again, now it should proceed upgrading.
Cheers, M
=(
Same problem! Trying to use no id upgrade . I hope it will solve my problem.
P.S. DO NOT upgrade ROM when batt is lo =)
I upgraded my 85' with the "official" wm6 rom and now I cannot go to other roms. The process was solid, meaning I was fully charged, no power loss, and it was synced. I've tried every version of rom available and get the same results. I went through the "brick" thread and I'm affraid I don't quite fit into any category. I can get phone calls and everything works, I just happen to like all of the great ROM's everybody is cooking and want to try them to see which one I favor. I tried using the Hard-SPL and all of the other bootloaders out there and I always get that ERROR [206]. I've tried to restart the machine, and hard reset the 85'. Any good idea's.... Maybe I need to search more? I'll try that.
==============================================================================
UPDATE:
What I should really do is rent a gun, and buy a bullet...
I'm not saying I'm some sort of season veteran of flashing... but I've never had to touch anything after I accept all terms. For some reason, when it came down to the last "Next" form, my phone flashes "Accept" super fast. So what to do?... I push "Yes" soft key fast as I can and it runs like grease lightening... I had to choose SS for the boot loader because it couldn't figure it out... Maybe next time around.
Have you tried to flash a coocked ROM using the microSD card?
Hi,
did you try get your phone in the tri color bootloader screen and then running the Hard SPL program again?
I did not try to do flash it woth the MicroSD card... I just found out that I could flash it with the MicroSD card about 2 seconds ago. And I wanted to Hard-SPL at the tri-color as a last result in fear of bricking but everything is okay now. As I said before, I've never had to touch my 85' while flashing the rom, it just did it on it's own, but that "official" rom was not about being neglected. And then when I saw it flash something and say "yes", I pushed it and never looked back. It's alllllllllllllllllll good.
I do have one question, is the SSPL preferred over the other choices? Or is there one that is recommended?
Hi joshkrajnak,
How did you solve this problem exactly cos I dont understand what your saying:
http://forum.xda-developers.com/showthread.php?t=298640
boz said:
I extracted these error codes from a Hermes rom upgrade 'read me' document, these should be of help if you get an error message during a rom upgrade. They should be common to all roms, please correct me if I am wrong.
ERROR [202, 204] : CONNECTION
This error message will appear when the device is not connected to ActiveSync correctly. Make sure you properly connect the device to the PC through ActiveSync before running RUU.
ERROR [260] : CONNECTION
This error occurs when there is an “open port error” before upgrading the CE ROM image.
Solution: You can reset the device and run RUU again. If you still encounter an “OPEN PORT ERROR” again, reset your computer and try again.
ERROR [206] : MEMORY ALLOCATION
ERROR [280] : UPDATE ERROR
When you see any of these error messages, close other running programs on the computer and run RUU again.
ERROR [208] : FILE OPEN
ERROR [210] : FILE READ
These error messages indicate that RUU lacks certain important files and cannot continue with the update. Please get the complete RUU package again.
ERROR [212] : FILE CREATE
ERROR [214] : FILE WRITE
ERROR [222, 224] : DEVICE NOT RESPONDING
These error messages will appear when remote access control has failed. Check the ActiveSync connection and try running RUU again.
ERROR [220] : MAIN BATTERY POWER
This error message will appear when the device’s battery power is not sufficient. Although RUU will instruct you to plug in the AC adapter, it still has to make sure that your device has enough power to upgrade the radio. (Even when you plug in the AC adapter, the device is unable to charge the battery when it is upgrading the radio).
ERROR [238] : FILE READ
This error message may appear when, for some unknown reason, the ROM image on the Mobile Device is corrupt. Download the whole RUU and try again.
ERROR [240] : FILE OPEN
When this error message appears, check whether the downloaded image is placed in the directory of RUU. If, for some unknown reason, you find that the ROM image is not located in the RUU folder, you have to download the RUU and retry again.
ERROR [242] : INVALID LANGUAGE
ERROR [244] : INVALID MODEL ID
ERROR [294] : INVALID VENDER ID
ERROR [296] : UPGRADE ONLY
One of these error messages will appear when you use the wrong RUU to do the upgrade. RUU will check if the Model ID and Language ID are compatible with the device. Make sure you use the appropriate RUU tool to upgrade.
ERROR [246] : DEVICE NOT RESPONDING
This error message indicates that RUU cannot start the update process. Please contact your service provider for assistance.
ERROR [262, 276, 284, 302] : UPDATE ERROR
This error occurs during the CE ROM code upgrade process.
Solution: If this happens, you can just soft-reset the device and run RUU again. The update process will then continue.
Note: At this stage, the Wince is destroyed; instead, it is in upgrade mode.
ERROR [300] : INVALID UPDATE TOOL
This error message will appear when you use the incorrect RUU version to upgrade.
ERROR [330] : ROM IMAGE ERROR
This error message will appear when you use the incorrect RUU to upgrade and the image file size is larger than the Flash ROM size. In this case, download the correct RUU version to upgrade.
Click to expand...
Click to collapse
To Clarify: Whenever I went to upgrade my 85' to a different ROM, it wouldn't recognize my bootloader, and then after selecting any of the options, it would give the "ERROR [206]" message and fail miserably with any rom.
What I did to correct it was this: On the "official release" whenever I went to upgrade the ROM, the 85' would show a message at the bottom, the same as any "Notification" would giving me the option to either "confirm" or "dismiss". I did not notice the messages up until it caught my attention out of the corner of my eye on the very last attempt. The messages would quickly appear and disappear, so when the time came and it stated:
Current Rom: 3.25.###.###
Upgrade: 1.##.###
I had to press a confirm notification to continue on or I would get the "206" error message. The quote posted by Binyo is correct, but it does not apply in my situation.
ERROR [206] : MEMORY ALLOCATION
ERROR [280] : UPDATE ERROR
When you see any of these error messages, close other running programs on the computer and run RUU again.
Although that may be true that some applications may interfere with the upgrade process, I had turned off all applications and killed any services during this process.
Does anyone have this problem?
Everytime I try to load Advanced Config, I get an unexpected error has occured....
ttvl4447 said:
Does anyone have this problem?
Everytime I try to load Advanced Config, I get an unexpected error has occured....
Click to expand...
Click to collapse
could you add more details on error??
Olioaglio
Hi,
I'm running on Schap's 3.54 ROM.
It attempts to load some files or settings, but half way through it says "An unexpected error has occured in AdvancedConfig.exe. Select Quit and then restart this program"
I clicked on Details and copied it as follow:
AdvancedConfig.exe
FormatException
at System.Boolean.Parse()
at System.Convert.ToBoolean()
at System.String.System.IConvertible.ToBoolean()
at System.Convert.ToBoolean()
at AdvancedConfig.Ӓ.֘()
at AdvancedConfig.Ӓ.ը()
at System.Windows.Forms.Form.OnLoad()
at System.Windows.Forms.Form._SetVisibleNotify()
at System.Windows.Forms.Control.set_Visible()
at System.Windows.Forms.Application.Run()
at AdvancedConfig.ִ.ֿ()
i encountered an error during auto-config too.
I was flashing a cooked WM6 rom....it was successfull, then attempts to do some auto-config, but in the middle of the process, during "Running Dopod_Black.tsk... it stops and hangs with a message saying
Windows\custTSK.exe does not exist!
then nag-hang na sya I cant tap OK nor can I click on any hardbuttons...only way is to softreset
any clues?
ttvl4447 said:
Hi,
I'm running on Schap's 3.54 ROM.
It attempts to load some files or settings, but half way through it says "An unexpected error has occured in AdvancedConfig.exe. Select Quit and then restart this program"
I clicked on Details and copied it as follow:
AdvancedConfig.exe
FormatException
at System.Boolean.Parse()
at System.Convert.ToBoolean()
at System.String.System.IConvertible.ToBoolean()
at System.Convert.ToBoolean()
at AdvancedConfig.Ӓ.֘()
at AdvancedConfig.Ӓ.ը()
at System.Windows.Forms.Form.OnLoad()
at System.Windows.Forms.Form._SetVisibleNotify()
at System.Windows.Forms.Control.set_Visible()
at System.Windows.Forms.Application.Run()
at AdvancedConfig.ִ.ֿ()
Click to expand...
Click to collapse
Wasn't something like this discussed HERE
Watch out for post #76 in this thread...
Also watch out for post #85 for the correct value
Olioaglio
Ok I saw the posts. Unfortunately the solution is too advanced for a noob like me.
Just flashed to TNT 2.0 Pro ROM and solved my problem
Hi friends,
I got HTC S620 Smartphone from my brother US. It was working well for the past 6 months and i updated to WM6 also now suddenly it got corrupted and shows the following error. It takes 30 min to boot and hangs with this following error. i Unable to do anything. I tried to update WM6 again but same still same error. I gave it to HTC service center in chennai and he unable to resolve this problem. And I Unable to open folder with usb cable. Any one please help me.
t-zones
While retriving the URL :
http://wap.t.zones.com
the following error occured:
Network error 19:
The Attempt to connect to the server failed
More Information Try Again
Alert
Cannot Start 'winwapexe'. A critical component
is either missing or failed due to low memory.
Try to upgrade to the HTC rom, it should be in this forum and I think its the second one on this page... Just look up and you should see the guide to upgrading your rom...
Read the topic that says guide to upgrading from WM 5 to WM 6 (or something along those lines)...
Hi I already Installed WM6 and after this problem again i done WM6 update. I have a doubt with this update. And i Unable to Open Windows Mobile folders from my computer also Active Sync unable to connect with Mobile. But i can receive the call and make answer to them sometime( even Hanging condition).