I have bricked my O2 Stealth due to an incorrect power adapter
So now i cannot enter bootloader mode also
So i have decided to flash the bootloader of the Stealth using JTAG method, but have run into a couple of problems
1. Where do i get the bootloader for O2 XDA Stealth ???
2. What is the JTAG pinout for the stealth ????
I have uploaded a pic of the JTAG points of the motherboard of the Stealth, please help me by sharing you suggestions and experiences.
O2 XDA Stealth JTAG
sirrus_linux said:
I have bricked my O2 Stealth due to an incorrect power adapter
So now i cannot enter bootloader mode also
So i have decided to flash the bootloader of the Stealth using JTAG method, but have run into a couple of problems
1. Where do i get the bootloader for O2 XDA Stealth ???
2. What is the JTAG pinout for the stealth ????
I have uploaded a pic of the JTAG points of the motherboard of the Stealth, please help me by sharing you suggestions and experiences.
Click to expand...
Click to collapse
Hello fellow developers. I am also happy (not) to say that I have bricked my O2 Stealth.
Has anybody been able to make any progress on debricking this phone using the JTAG method? I have two of these phones (one bricked) and I can confirm that on both phones there is evidence of test probing on the contacts marked with red ink shown in the previous post.
If these are the JTAG pins, is there any way of identifying which pin is which by probing with a multimeter and an oscilloscope?
Any help would be greatly appreciated.
Email me to get the bootloder and JTAG pins
[email protected]
I'm too busy to share it to every one
O2 XDA Stealth JTAG pins
Thanks Slimli,
You are a champion !!! The photo of the JTAG pins made all the difference.
I then just simply followed the O2 Dead Boot tutorial that's floating around. I made up my own JTAG connector with odds and ends I found in the garage, and I replaced the EBO_a.nb0 file with the stealth bootloader you had also sent me. I now have Windows Mobile 6.5 running on my phone.
Once again, Thanks Slimli, you are a champion !!!!!!!!!!!
Help...
Hi...if anyone has any methods or files and pics or guides on how to unbrick the XDA Steealth, kindly share.
Or atleast give a link to where these can be downloaded. Email will be good as well.
[email protected]
Thanks in advance.
Stoing said:
Hi...if anyone has any methods or files and pics or guides on how to unbrick the XDA Steealth, kindly share.
Or atleast give a link to where these can be downloaded. Email will be good as well.
[email protected]
Thanks in advance.
Click to expand...
Click to collapse
Please help me too .
[email protected]
My Stealth is alive again
Hello all. Thank you all for helping. My stealth is alive again.
It did take a few tries but in the end.....it all worth it.
Thanks again.
Stoing said:
Hello all. Thank you all for helping. My stealth is alive again.
It did take a few tries but in the end.....it all worth it.
Thanks again.
Click to expand...
Click to collapse
can u tell me how to solved this problem ?
tell me step by step please
Stoing said:
Hello all. Thank you all for helping. My stealth is alive again.
It did take a few tries but in the end.....it all worth it.
Thanks again.
Click to expand...
Click to collapse
Now i have Ebo_a.NB0
and i have H-jtag program and i connect with my stealth via LPT port.
Which address or type to flash this file to my stealth ?
I followed instructions given here:
http://wiki.xda-developers.com/index.php?pagename=DeadBoot
These instructions can also be found here:
http://forum.gsmhosting.com/vbb/showthread.php?t=680669
I used the program in this package:
http://wiki.xda-developers.com/uploads/RepairBootLoader.zip
Replace EBO_a.nb0 given in this package with the Stealth bootloader.
The addresses and flash type are set up in 'start.bat'. They also apply to the Stealth. Open a DOS shell in the same directory as 'start.bat' (which also has 'EBO_a.nb0'), and then at the DOS prompt, type 'run start'. The only tricky part is to get a good contact on the jtag pins. The rest was easy.
thank you
gooday said:
I followed instructions given here:
http://wiki.xda-developers.com/index.php?pagename=DeadBoot
These instructions can also be found here:
http://forum.gsmhosting.com/vbb/showthread.php?t=680669
I used the program in this package:
http://wiki.xda-developers.com/uploads/RepairBootLoader.zip
Replace EBO_a.nb0 given in this package with the Stealth bootloader.
The addresses and flash type are set up in 'start.bat'. They also apply to the Stealth. Open a DOS shell in the same directory as 'start.bat' (which also has 'EBO_a.nb0'), and then at the DOS prompt, type 'run start'. The only tricky part is to get a good contact on the jtag pins. The rest was easy.
Click to expand...
Click to collapse
thank you
Make sure the contacts to the Jtag are done properly........I had to flash a few times to get it right...
Good luck !!
It's work mann!! .
My stealth is comeback .
Thank you .
help me out
hey Stoing, plz help me out with the contact pins for stealth. as i dont know which contact pin is TDI, tdo, tck and tms. plz help me out, thnks in advance.
Please help me I'm having problem with my stealth which I have posted here http://forum.xda-developers.com/showthread.php?t=538234
JTAG for Stealth
Can someone help me to corectly identify JTAG pins for Stealth.
When I am flashing my Stealth, it failed half way.
Now only Lights are blinking.
NEED EXPERT ADVICE
Same with me basha. Please anyone here who can share the correct positions of jtag pins and bootloader of stealth. I emailed slimli, but he does not reply. I think he is busy. Thanks in advance.
Email Add
Give ur email addresses......will forward the emails from Goodday and Slimli
Emai Ad
Here's my email ad: [email protected]. Thanks in advance.
gooday said:
I followed instructions given here:
http://wiki.xda-developers.com/index.php?pagename=DeadBoot
These instructions can also be found here:
http://forum.gsmhosting.com/vbb/showthread.php?t=680669
I used the program in this package:
http://wiki.xda-developers.com/uploads/RepairBootLoader.zip
Replace EBO_a.nb0 given in this package with the Stealth bootloader.
The addresses and flash type are set up in 'start.bat'. They also apply to the Stealth. Open a DOS shell in the same directory as 'start.bat' (which also has 'EBO_a.nb0'), and then at the DOS prompt, type 'run start'. The only tricky part is to get a good contact on the jtag pins. The rest was easy.
Click to expand...
Click to collapse
Follow and
use this file
http://www.tempf.com/getfile.php?id=65730&key=4a765e3f4d563
Related
hi guys,
can anyone tell me how do I reflash my phone and from where can I get the files to relash. If some body could tell me in detail i will be really gratefull.
Pls do a search..u will find the answers
kadavinash said:
hi guys,
can anyone tell me how do I reflash my phone and from where can I get the files to relash. If some body could tell me in detail i will be really gratefull.
Click to expand...
Click to collapse
Download an 'update' from your operator's support website. If your phone won't boot enough so that it can connect via activesync then just use the bootloader method.
Read the WIKI page for all instructions http://wiki.xda-developers.com/index.php?pagename=HTC_Universal
Good luck!
try a hard reset first.
reset + left and right soft buttons i think
I bought a used HTC s630 from ebay. The guy said that it would freeze at the loading screen. When i got it i did a hard reset using the 2 softkeys and power button. Worked for a while, then when i went to use it again and turned it on it goes to the homescreen but i cant do anything. When i press any keys the keyboard lights up but thats all.when i plug in the charger the battery icon on the screen shows that its charging but thats the only change. Im thinking that if i flash the shipped rom again itll fix it, but i cant seem to find it anywhere? any ideas please????
try upgrading the rom? Maybe that would help?
If you go to xda Wiki there is a Dopod C730 rom there.
Also, Curzz has cooked a bunch of awesome WM6.1 roms, you can try loading that.
to do that i need to do the hard spl so i can load diff roms other than htc's, and to do that i need to app unlock[ it which requires it to be connected through active sync. i tried loading others but i get error codes like 290 which is incalid vendor id. the only solution that i can see right now is to flash the shipped rom though the bootloader. does anyone have the shipped htc WM6 rom?
I have an original HTC S630 (Branded HTC) with original WM 6 rom, but I dunno how to copy my rom on to the computer, if you can tell me how to do it, I'll be happy to do it for you
OMG thank you so much. AND YOUR EGYPTION!! Salam Alakum, Im egyption as well. I will look in to see how to dump a rom. If anyone else knows the help would be appreciated.
THis is the link that cruzz provided when he was trying to get a copy of all the roms.
http://wiki.xda-developers.com/index.php?pagename=Elf_HowToDumpOSManually
I have tried that procedure before and it did not work.
Have you tried going to the agent in Cairo, JoviTronics? You could ask them to re-install the rom again.
Did you buy your phone from Vodafone?
I actually live in america. I bought the phone used from ebay. I just called htc and they say its still under warranty, but i want to try and fix it myself before sending to them. maybe cruzz has a copy of the rom?
what error did u get when u tried extracting the rom?
did u get this
D:\_ROM>pdocread.exe -l
Copying D:\_ROM\itsutils.dll to WCE:\windows\itsutils.dll
Could not update itsutils.dll to the current version, maybe it is inuse?
try restarting your device, or restart ActiveSync
Click to expand...
Click to collapse
pls make sure that u have unlock ur dev
modify this registry key, and then softreset using power button:
HKLM\Security\Policies\Policies
valuename '00001001' was set to dword:2, change it to dword:1
dword: any thing other than 1 disallows unsigned
dword: 1 allows unsigned
Click to expand...
Click to collapse
then follow the instruction of the Wiki
cruzz do u have any idea what could be wrong with the phone and what i could do to fix it?
molesaied88 said:
cruzz do u have any idea what could be wrong with the phone and what i could do to fix it?
Click to expand...
Click to collapse
Not sure .... u can do a hard spl? if can u can try use mtty to check if the os has bad sector. U can get the link on how tos at the sticky thread "for newbie...."
regards
thing is i cant do hardspl without app unlock which needs activesync. thats why im tryin to find the htc shipped rom
so it turns out that the phone i bought off of ebay for 30 dollars was broken, but lucky me it was still under warranty. i sent it to htc for repair and they replaced the entire board for me free!! waiting for it to be delivered, then ill pull the htc wm6.0 rom off of it for u guys.
molesaied88 said:
so it turns out that the phone i bought off of ebay for 30 dollars was broken, but lucky me it was still under warranty. i sent it to htc for repair and they replaced the entire board for me free!! waiting for it to be delivered, then ill pull the htc wm6.0 rom off of it for u guys.
Click to expand...
Click to collapse
glad to hear that ur prob shall be fix ... good for u then
I've searched the whole thread and tried every method to unbrick my phone but my phone wont even go in to download mode the screen is black and blank Please help all this happened after trying to unlock.
Try to charge your phone from the wall. Any luck?
Sent from my LG-LS970 using xda premium
Ninja25 said:
Try to charge your phone from the wall. Any luck?
Sent from my LG-LS970 using xda premium
Click to expand...
Click to collapse
I tried no luck when I connected the phone to my computer it attempted to install this driver qhsusb_dload and failed.
Try going over to the AT&T thread.
See if this post has any helpful info...
http://forum.xda-developers.com/showthread.php?t=2006946
I think that post has info on accessing the irc channel...you can get the LGNPST files from there.
Good luck.
Sent from my Optimus G using xda premium
ur phone become a hard brick,install qualcomm's driver,will appear a...qualcomm xxx 9008,pls use QPST emmcswdownload repair it,ok
Sent from my SHV-E120L using xda premium
my phones hard bricked can u plz tell me how to unbrick it ?
starteam said:
ur phone become a hard brick,install qualcomm's driver,will appear a...qualcomm xxx 9008,pls use QPST emmcswdownload repair it,ok
Sent from my SHV-E120L using xda premium
Click to expand...
Click to collapse
Plz help me unbrick my hard bricked phone
I wouldn't recommend it. Please go to a gsm service.they will fix it.If you are not a tech wizzard,then don't try to recover a hard brick phone home.there are alot of command lines to be written and the most slightest mistake will result in a permanent brick,beyond repair.You have 2 choices : send the phone to warranty,tell them it died.Go to a service and pay about 20 bucks to repair it.
[email protected]! said:
Plz help me unbrick my hard bricked phone
Click to expand...
Click to collapse
http://bbs.gfan.com/forum.php?mod=viewthread&tid=6269182&extra=page=1
starteam said:
http://bbs.gfan.com/forum.php?mod=viewthread&tid=6269182&extra=page=1
Click to expand...
Click to collapse
i read it but i cant understand it fully
plus its asking for money for downloading the files...............
can u eloborate it plz ?
write and explain in simple steps....
i am geting the error "image download failed cookie (if present) not received"
[email protected]! said:
i read it but i cant understand it fully
plus its asking for money for downloading the files...............
can u eloborate it plz ?
write and explain in simple steps....
i am geting the error "image download failed cookie (if present) not received"
Click to expand...
Click to collapse
if so,you can only use JTAG to repair it
starteam said:
if so,you can only use JTAG to repair it
Click to expand...
Click to collapse
No other way really ?:crying:
I am also facing cookie not received error on QPST. But my phone is Cherry Flare, qualcomm msm8225 based.
I had updated my phone to Jelly Bean (used it for 3 days) which died while it was charging. I tried to flash bootloader through QPST, but got the cookie error. I assume the QPST can solve the flash problem if something went wrong while updating firmware. In my case I was not updating the firmware, it suddenly died. After reading so many forums, I could not find any solution and am thinking that the phone is beyond repair by myself.
Now my question:
1. Can service center repair the phone through JTAG? I believe JTAG can directly access eMMC flash which QPST could not.
2. If not, can eMMC be replaced? Or the entire main board needs to be changed?
If the emmc is intact,jtag can fix it.
If the emmc buffer is corrupted or full with bad attempts to recover,the only way is to change the mainboard.
Happend to a friend with a galaxy note.he tried so many times to fix it with odin home until it was too late for jtag.it could't acces the emmc.
Anyway,if the phone is hard bricked,it can't be traced.so send it to warranty.
Sent from LG E975 pwd by CM 10.1
Hi guys...
my DHD is hard bricked and is not detected by any software except QPST (Qualcomm Product service Tool).... in eMMc software download it shows my phone in download mode....
i have seen some posts on the internet for repairing dead boot with qpst, i just need the firmware that is supported by this programme.... plz someone help me.....
QPST need .hex files.... i could`nt find them any where....
junaid.rajput said:
Hi guys...
my DHD is hard bricked and is not detected by any software except QPST (Qualcomm Product service Tool).... in eMMc software download it shows my phone in download mode....
i have seen some posts on the internet for repairing dead boot with qpst, i just need the firmware that is supported by this programme.... plz someone help me.....
QPST need .hex files.... i could`nt find them any where....
Click to expand...
Click to collapse
Forget it my brother. I had the same problem and I never found them. Those files are strictly released to Qualcomm developers only.
I would suggest u get another motherboard from a dhd and replace it with urs.
You can search eBay for DHDs with cracked screens for lower prices.
mickeyasamoah said:
Forget it my brother. I had the same problem and I never found them. Those files are strictly released to Qualcomm developers only.
I would suggest u get another motherboard from a dhd and replace it with urs.
You can search eBay for DHDs with cracked screens for lower prices.
Click to expand...
Click to collapse
Thanks for the response bro.... you have been very helpfull..
Is there any way to create that file.
ro1407 said:
Is there any way to create that file.
Click to expand...
Click to collapse
There were some tutorials, but even those methods needed certain files we couldn't find.
Sent from my XT912 using XDA Free mobile app
Hey guys, I have here a cloned Samsung galaxy grand duos GT-I9082 which is owned by my neice and it comes with MT6572 Chipset and a 1GB of RAM. So the problem is it was boot looped due to change of dpi and the worst is, she used the root function in MTK Droid tools though it is already rooted via framaroot and I think what she does really messed up the device. Now I can't access the recovery (through pressing both volume down + power) though it's in chinese language before. When I tried to boot it normally, it just opens the backlight for 10 seconds then turns off then turns on again. When I pressed the volume up + power, "Android System Recovery <3e>" pops out, which is strange co'z it wasn't there before (according to my neice). The only way adb detects the phone is when I choose "apply update using ADB" and there it was detected as a sideload. Lastly, when I do a normal boot while connected to a pc, in device manager, an "MT65XX Preloader" driver pops out (meaning it is detected) before the device restarts again.
So, does this phone still have a chance to be fixed? I feel it still have a little chance, but I don't know anymore where to find any solution to this problem. Hope you guys help me regarding this issue. God bless!
up up up up
im also having the same problem.
does anyone know what to do?
THANKS
If you really want to you can reinstall the official firmware. Use this link
http://www.needrom.com/download/gt-i9082-mt6572/
I'm brick my phone month before.
Suggestion from upper post not work for me.
Do you have another suggestion - rom?
CU
UPDATE: I've found a working ROM for my phone in 4shared. But it does not detect the inserted sim cards because it doesn't come up with "secro.img" file. You might try flashing this ROM here: (kindly remove spaces on the link as XDA prohibits posting of links with at least 10 posts.)
http :// www .4shared .com /rar/ gcWm1jxsba/ I9082-2SIM-OK-MT6572. html
thank you so much for your reply ill try it now hope it works. update you soon with my progress.
it worked but still cant find a way to fix the sim problem
thanks
I'm glad that it also works on your device. And finally I've found a workaround for this undetected SIM cards problem. All you have to do is to enter your IMEI inside the engineer mode. So first, download "MTK engineer mode" in play store then in the app, choose "MTK settings" and then tap "GPRS" then enter your IMEI for SIM 1 (if you only have 1 IMEI, you can both enter the same IMEI for SIM 2. DO NOT INCLUDE SPECIAL CHARACTERS). After typing your IMEI, tap "Write IMEI". Do the same procedure for SIM 2. Once you're done, close the app then restart. Hope this works for you.
not works...no imei yet
LiveLaughLend said:
I'm glad that it also works on your device. And finally I've found a workaround for this undetected SIM cards problem. All you have to do is to enter your IMEI inside the engineer mode. So first, download "MTK engineer mode" in play store then in the app, choose "MTK settings" and then tap "GPRS" then enter your IMEI for SIM 1 (if you only have 1 IMEI, you can both enter the same IMEI for SIM 2. DO NOT INCLUDE SPECIAL CHARACTERS). After typing your IMEI, tap "Write IMEI". Do the same procedure for SIM 2. Once you're done, close the app then restart. Hope this works for you.
Click to expand...
Click to collapse
not works...no imei yet
faizalaziz said:
not works...no imei yet
Click to expand...
Click to collapse
Sorry to hear that. But would you please describe the events or errors you have encountered? Maybe I can help you out even more then.
By the way, I just want to ask if you still have your "secro.img" back up before? You might try to flash it on your device then do the instructions I've posted before. Good luck!
hi bro, please give step by step process for my samsung galaxy grand duos i9082.
LiveLaughLend said:
Sorry to hear that. But would you please describe the events or errors you have encountered? Maybe I can help you out even more then.
By the way, I just want to ask if you still have your "secro.img" back up before? You might try to flash it on your device then do the instructions I've posted before. Good luck!
Click to expand...
Click to collapse
im newbie here please give step by step process for my samsung galaxy grand duos i9082.
i need change my IMEI number
thanks
redrider5 said:
im newbie here please give step by step process for my samsung galaxy grand duos i9082.
i need change my IMEI number
thanks
Click to expand...
Click to collapse
I already discussed before on how to change IMEI sir, just re-read the post #8.
not works...no imei yet
i have bricked my device i9082 MT6572 clone, same with yours right? most probably, the ROM you flashed was a little bit incompatible due to its scatter file. i've detected the problem and you had not included the secro.img which is essential for the IMEI, though flashtool can't include it coz the address is not correct.. after hard works, i've got to have a working ROM but i've not uploaded it yet. i'm gonna upload it soon so please, stay tuned
WE waiting for you guy
JoverTan said:
i have bricked my device i9082 MT6572 clone, same with yours right? most probably, the ROM you flashed was a little bit incompatible due to its scatter file. i've detected the problem and you had not included the secro.img which is essential for the IMEI, though flashtool can't include it coz the address is not correct.. after hard works, i've got to have a working ROM but i've not uploaded it yet. i'm gonna upload it soon so please, stay tuned
Click to expand...
Click to collapse
we waiting for you guys.pleas upload now
Handyshell said:
we waiting for you guys.pleas upload now
Click to expand...
Click to collapse
please, follow the instructions carefully
www (dot) mediafire.com/download/6ay7fvoqm6mvbdz/I9082+CLONE+MT6572+ROM (dot) rar
please replace the '(dot)" with real one..
spread the news.......
accept pls. thanks
JoverTan said:
please, follow the instructions carefully
www (dot) mediafire.com/download/6ay7fvoqm6mvbdz/I9082+CLONE+MT6572+ROM (dot) rar
please replace the '(dot)" with real one..
spread the news.......
Click to expand...
Click to collapse
can you accept my request? i need that rom badly. pls
Jayz2304 said:
can you accept my request? i need that rom badly. pls
Click to expand...
Click to collapse
i'm sorry, i forgot my account on XDA. i'm the owner of that file. can you tell me your email add so i can accept your request?
---------- Post added at 05:45 AM ---------- Previous post was at 04:58 AM ----------
I've already turned it into a public file www (dot) mediafire.com/download/6ay7fvoqm6mvbdz/I9082+CLONE+MT6572+ROM (dot) rar
please hit thanks
JoverTanB said:
[/COLOR]I've already turned it into a public file www (dot) mediafire.com/download/6ay7fvoqm6mvbdz/I9082+CLONE+MT6572+ROM (dot) rar
please hit thanks
Click to expand...
Click to collapse
It's not public.
And could you please provide me with your board ID ? (The clone phone's motherboard ID is written on it, you have to take the phone apart to get it) if it's not much to ask
I have a I9082 MT6572 clone with board ID: W05-MB-V2.0 , the device is infected with Timeservice & Monkey test and several other malware that I don't know how to get rid of except with a fresh flash.
Thanks in advance!
Bugz! said:
It's not public.
And could you please provide me with your board ID ? (The clone phone's motherboard ID is written on it, you have to take the phone apart to get it) if it's not much to ask
I have a I9082 MT6572 clone with board ID: W05-MB-V2.0 , the device is infected with Timeservice & Monkey test and several other malware that I don't know how to get rid of except with a fresh flash.
Thanks in advance!
Click to expand...
Click to collapse
i'm sorry to tell that i've already given the phone to someone and i'm not able to do your request anymore. I've turned it back into a private file (the ROM). please provide to me your e'add to make you access the file. my email is [email protected].
JoverTanB said:
i'm sorry to tell that i've already given the phone to someone and i'm not able to do your request anymore. I've turned it back into a private file (the ROM). please provide to me your e'add to make you access the file. my email is [email protected].
Click to expand...
Click to collapse
Thanks ! This is my E-mail address: [email protected]
Although I don't have the device anymore, but it would be good to have the flash files ready anyways!