Develop Bugs

xda2s new lcd screen fitted but wont work

I have just fitted a replacment screen to my xda2s but when i turn it on all
i get is a bright white screen and nothing else. can anyone advise me as to why this is and what to do

either you haven't secured the cable correctly or you have fitted the wrong screen. read the wiki, there are 3 types.
Richard

Not all HTC Blueangels are the same
Check out this link. I think this is your problem.
http://wiki.xda-developers.com/index.php?pagename=BlueangelLCD
XDA 2s has board id 0x5 and will only use sony LCD
Check the part no.

Re: Not all HTC Blueangels are the same
diggy said:
XDA 2s has board id 0x5 and will only use sony LCD
Check the part no.
Click to expand...
Click to collapse
Not necessarily - I have had XDA2s' with 0x6 boards - the wiki is not 'official' so may be missing info. The way to tell for sure is check the part number of the old and new screens.
The only blueangel type I've seen to always have the same board fitted was the VPx - perhaps as they didn't make so many.
Richard

Fluffcat1 io aspetto da lei ancora 5 connettori pagati con paypal.
Le ho mandato anche una email.
I waiting 5 connector for XDA2
I send you email.

Prophet speaker !

Hello there
Suddenly my prophets speaker at the back stopped working ! For no reason.. I found out that if i pressed a little at it it worked again but only while i pressed at it.. I took my prophet apart, because i thought it was a jamed connection, but it wasn't and now the speaker dosn't work at all..
So i would like if anyone could tell me where i can get spareparts for the prophet ? I come from denmark, so if its possible, i need them to ship internationally
Thanks !
~D

Da9L said:
Hello there
Suddenly my prophets speaker at the back stopped working ! For no reason.. I found out that if i pressed a little at it it worked again but only while i pressed at it.. I took my prophet apart, because i thought it was a jamed connection, but it wasn't and now the speaker dosn't work at all..
So i would like if anyone could tell me where i can get spareparts for the prophet ? I come from denmark, so if its possible, i need them to ship internationally
Thanks !
~D
Click to expand...
Click to collapse
see this link:http://www.impextrom.com/tienda_producto.asp?id_tienda=13&id=12480
i´m portuguese and buy one for my qtek s200, work perfectly.

skipjack10 said:
see this link:http://www.impextrom.com/tienda_producto.asp?id_tienda=13&id=12480
i´m portuguese and buy one for my qtek s200, work perfectly.
Click to expand...
Click to collapse
Thanks for the link ! Allthough i have no idea what the language on the page does mean..

http://stores.ebay.com/e2shopstore the best one! =)

Da9L said:
Thanks for the link ! Allthough i have no idea what the language on the page does mean..
Click to expand...
Click to collapse
the language is spanish!

the language in this site is spanish, sorry but, i can find better

P4k1t0 said:
the language is spanish!
Click to expand...
Click to collapse
skipjack10 said:
the language in this site is spanish, sorry but, i can find better
Click to expand...
Click to collapse
Thank you ! all i need to know.. My girlfriend knows spanish so i will just let her read it for me..

P4k1t0 said:
http://stores.ebay.com/e2shopstore the best one! =)
Click to expand...
Click to collapse
That shop looks interresting ! They have many things !

Speaker repair
I had the exact same problem. It seems HTC was saving money on the glue for that batch in particular. I 'fixed' my speaker several monthes ago, and it's still working fine.
What I did was put a small piece of twist-tie, (or wire would work too I guess) in the shape of a half circle between the speaker and housing. This keeps the pressure on it, like you mentioned when you push it. When this stops working I may consider buying a new speaker, but it works just fine!

This seems to be a frequent problem, my speaker also just died yesterday, again for no reason. My solution was similar to Stuclint's, I put a bit of folded paper to keep the pressure on it. Sound quality is awful though, so I ordered a new one for £6 from ebay, but at least now I can hear it ringing

I bought a new speaker too...
... but mine is from IPMART. Costs around $4.00 US, but I only bought it to fill up my shipping weight. The prices are great, but shipping (to germany at least) costs a fortune! I also ordered a new housing ($19.95), but got the wrong one. It was a 818 housing instead of the 818pro I ordered. I'm still trying to get the right one, and was also waiting until then to use the new speaker. But like I say, the solution I'm using now works fine. No noticable distortion. My housing is toast though, try not to drop it on the SD card side.... I did and now have a huge opening all down the Camera, Volume, CommManager side.

I have the replacement speakers if anyone needs them. $4 for the speaker and $3 for the shipping.

can some one tell me is is it easy replace that eis just pull out from de conector?
`e facil de trocar? é so puxar e ele sai do conector ou tenho de ter algum cuidado?
abraço

enduromen said:
can some one tell me is is it easy replace that eis just pull out from de conector?
`e facil de trocar? é so puxar e ele sai do conector ou tenho de ter algum cuidado?
abraço
Click to expand...
Click to collapse
It's quite easy to replace. You don't need to solder anything. There is a little white clip that fits into a connection on the mainboard. You can change a speaker in about 10 minutes.

thanks for the anwser my friend. I see the white clip conector that you talk about. Now i need too know that is just disconet? just pull out?. I ask that because a few mouth ago to change a display i damage the conector because i don´t know there are a grey secutity clip that we have to pull out.

If you live in Rome, there is a shop that sells the speakers and all spareparts along the road leading from stazione tusculano towards via appia.

enduromen said:
thanks for the anwser my friend. I see the white clip conector that you talk about. Now i need too know that is just disconet? just pull out?. I ask that because a few mouth ago to change a display i damage the conector because i don´t know there are a grey secutity clip that we have to pull out.
Click to expand...
Click to collapse
It will just pull out (there is no clip). You still need to be careful, but it will come out.

Prophet speaker
Me too ..
I bought one from
http://stores.ebay.com/ukhitechstore off Ebay ...
Cheers,
Wit C.

i have the exact same problem as the OP
went on ebay and bought the cheapest one i could find (came to US$9.98 shipped to Canada)
here are pictures of my broken one http://www.flickr.com/photos/shadowvlican/sets/72157607495602562/detail/

speaker arrived
shoved it in... fixed

[Q] {defy} - Defy as MP3 w/ regular sound system

Please,
I have a regular sound system with a AUX-IN. I can connect my ipod, and my sister philips gogear, as my Nokia E72, directly as mp3 players. But I can't connect my Defy. I use a p2-p2 cable, regular, and Defy doesnt recognize, the sound coming from the speakers (defy).
When I connect a "extend-cable" with a earphones, take it out and plug my p2-p2 cable on sound system, its work.
So, Can someone help me?
Why Defy doenst recognize my sound? Its to happens with my car system.
I really think I've spend money on motorola defy.
ps. sorry about my english.

Well...
I noticed that too.
To solve this I made a little modification on the P2 cable, just put a push-button between the ground (negative) and one of another wire (positive). You just need a momentary short on this wires for the phone recognize your sound system as a phone...
I dont now why motorola did this...
Mauricio

I just connected my Defy to my sound system and PowerAmp just started playing. I think that that short usually is done when inserting the jack.

This sounds like an impedance issue. The headphones are low impedance, aroud 32 ohms, but the aux-input is higher impedance, probably around 22k ohms. The proper solution would be to add two 33 ohm resistors to the cable, from ground to left and ground to right. They would add the correct loading to make the Defy think there is headphones connected.

Thanks Daniel, it's really happens w/ Poweramp, only w/ Poweramp, w/ the stock apps, its doesnt works. I've installed poweramp to solve this issue.

Mauricio,
Obrigado pela ajuda, não tenho o menor talento para eletronica, afim de conseguir instalar o botão nos cabos. Mas buscarei no google como proceder, ou mesmo em alguma eletronica especializada. Muito obrigado novamente pela disposição em ajudar.
abraço

Buzzband MB20 bluetooth bracelet wristband

Hi all,
I've got a bluetooth bracelet wristband Buzzband MB20 that was working with my old LG Optimus 2X smartphone.
I dropped it (the bracelet) because bluetooth was draining too much battery on my phone.
The Note part: so i've tried to connect it with my Galaxy Note but this one doesn't recognise the bracelet signal at all (my iPad is recognised)!
Anyone's got an idea?
Envoyé avec ma brique Galaxy Note.

Solved! After a week without using it, it has miraculously paired with my Note...
Back to tasker enjoyment
Envoyé avec ma brique Galaxy Note.

Dasaita stuck in reverse cam

Hello,
I have a Dasaita installed in my 2018 Toyota Avensis.
Unfortunately, after I put the device in reverse gear, it stays with the view of the rear camera. Dasaita has also already provided me with a new MCU version (see attachment), but unfortunately it did not help. The problem looks like this:
The reverse signal comes from the CAN BUS decoder.
Does anyone have an idea how I can solve this problem?

Does the reversing image go away when you turn the car off and back on and then return when you shift into reverse the first time?
I have a 2017 Toyota Camry which is similar to the Avensis with a PX6 SYGAV/DASAITA head unit.
Software suggestions:
Verify the Canbus options are correct for your vehicle. You can find these in Settings... Car... Factory settings.... 126
Here are the settings for my vehicle. Yours may be different. I would suggest setting the Type settting to "0 NO" as those seem to be quite specific to vehicle models with certain options. I had several check engine codes occurring with my car when Type was set to anything other than 0
You could also try setting the Canbus selection to 0 (effectively disabling the canbus adapter)
Hardware things to try:
1. Pull the ground wire from the car's battery for about a minute or so.
2. Try disconnecting the canbus adapter and then try shifting into reverse. The radio will function without the canbus adapter. This would tell you conclusively whether the reverse signal is indeed from the canbus adapter. I would not be very surprised if reverse works the same even without the canbus adapter. I know there is a reverse signal wire on the car harness on either the 24 pin connector or the 26 pin (can't remember right off which one but could find out if needed).
Maybe my suggestions will help somehow. Finally, you may have a defective canbus adapter or MCU board. Best of luck to you.

jlbooth said:
Does the reversing image go away when you turn the car off and back on and then return when you shift into reverse the first time?
Click to expand...
Click to collapse
No. When I turn off the car and then restart it, the rearview image is still there. Only if the car was off for a longer time, the device is not at the rear view camera image after the start.
jlbooth said:
Software suggestions:
Verify the Canbus options are correct for your vehicle. You can find these in Settings... Car... Factory settings.... 126
Here are the settings for my vehicle. Yours may be different. I would suggest setting the Type settting to "0 NO" as those seem to be quite specific to vehicle models with certain options. I had several check engine codes occurring with my car when Type was set to anything other than 0
You could also try setting the Canbus selection to 0 (effectively disabling the canbus adapter)
Click to expand...
Click to collapse
I have chosen the same CAN bus settings as you:
jlbooth said:
Hardware things to try:
1. Pull the ground wire from the car's battery for about a minute or so.
2. Try disconnecting the canbus adapter and then try shifting into reverse. The radio will function without the canbus adapter. This would tell you conclusively whether the reverse signal is indeed from the canbus adapter. I would not be very surprised if reverse works the same even without the canbus adapter. I know there is a reverse signal wire on the car harness on either the 24 pin connector or the 26 pin (can't remember right off which one but could find out if needed).
Maybe my suggestions will help somehow. Finally, you may have a defective canbus adapter or MCU board. Best of luck to you.
Click to expand...
Click to collapse
1. Pull the ground wire unfortunately did not help. Especially since the reversing signal works with the original Toyota Touch 2.
2. The signal comes 100% from the CAN bus adapter. It is possible to connect the cable either to the CAN bus or to the connector from the car. Unfortunately, the reversing signal is not assigned to the car connector.

The reason I was suggesting to try running without the Canbus was to hopefully confirm or exclude it as the source of the problem. Perhaps you could get Dasaita to provide a replacement Canbus adapter and/or harness, but then again maybe you could get them to replace the whole unit. Just be advised that their tech support will do everything they possibly can to get you to give up and go away.
I doubt Toyota would rely on a software signal to trigger the reversing camera on the factory display. Hope that you are able to get this sorted out. Best of luck to you.

Thanks for your help
I unplugged the reverse signal coming from the CAN bus adapter and plugged it back in. I assume that it is the CAN bus adapter:

I wonder if you could pick up the reverse signal from somewhere else like another harness under the dash, or even run a wire from the reverse lights on the back of the car? Sounds kind of extreme and that kind of takes away from the "plug and play" idea of having the Toyota specific harness from Dasaita. What you paid for should "just work" as advertised.
This might seem like a silly question and apologies in advance, but do the reverse lights turn on and off like they should? Of course, you know, if they do, the idea of running a wire from the positive lead on one of the reverse lights to the reverse signal wire on the back of the radio might be a possible workaround for your situation. I remember my 2010 Toyota Tacoma had a lead in one of the factory harnesses under the glove box area that I tapped to get reverse signal for an aftermarket radio.

jlbooth said:
I wonder if you could pick up the reverse signal from somewhere else like another harness under the dash, or even run a wire from the reverse lights on the back of the car? Sounds kind of extreme and that kind of takes away from the "plug and play" idea of having the Toyota specific harness from Dasaita. What you paid for should "just work" as advertised.
This might seem like a silly question and apologies in advance, but do the reverse lights turn on and off like they should? Of course, you know, if they do, the idea of running a wire from the positive lead on one of the reverse lights to the reverse signal wire on the back of the radio might be a possible workaround for your situation. I remember my 2010 Toyota Tacoma had a lead in one of the factory harnesses under the glove box area that I tapped to get reverse signal for an aftermarket radio.
Click to expand...
Click to collapse
chrisv4 said:
Thanks for your help
I unplugged the reverse signal coming from the CAN bus adapter and plugged it back in. I assume that it is the CAN bus adapter:
Click to expand...
Click to collapse
Your CAN unit isn't working correctly. Replace or workaround with signal wire as @jlbooth has suggested.
If this is out of your area of expertise, a local electrical/electronic repairer might be best to work with.

You can get a reverse signal from your reverse light. Use that instead of the can bus signal and see what happens

Thanks to all. I have now picked up the signal from somewhere else. Now everything works.

My pleasure @chrisv4. Thank you for reporting back your success .

Hello to everyone.
I have the same problem like chrisv4. I have contacted Dasaita and told them my problem. They still going around a circle and obviously don't know what is the problem. I have Toyota CH-R 2018, led lights. When I am switching to reverse, the screen is switching to reverse camera, but after swithcing to neutral (for example), the camera doesn't want to turn off. If I disconnected the cable like member chrisv4, the screen switched, but after putting the wire together, the reverse camera screen is went back again. I dont know, where the problem is, because on some youtube video, the people don't have a problem with factory camera. It seem that the camera is not grounded or somethink like that.
Do you have some ideas what it could be?
Thank you so much for your suggestion. I am also waiting for Dasaita engineer satement.

PatrikRilian said:
Ciao a tutti.
Ho lo stesso problema di chrisv4. Ho contattato Dasaita e gli ho spiegato il mio problema. Stanno ancora girando in cerchio e ovviamente non sanno qual è il problema. Ho Toyota CH-R 2018, luci a led. Quando si passa alla retromarcia, lo schermo passa alla telecamera per la retromarcia, ma dopo essere passati alla posizione neutra (ad esempio), la telecamera non si spegne. Se ho scollegato il cavo come il membro chrisv4, lo schermo è cambiato, ma dopo aver unito il cavo, lo schermo della telecamera inversa viene ripristinato. Non so dove sia il problema, perché su alcuni video di YouTube, le persone non hanno problemi con la fotocamera di fabbrica. Sembra che la fotocamera non sia collegata a terra o qualcosa del genere.
Hai qualche idea su cosa potrebbe essere?
Grazie mille per il tuo suggerimento. Sto anche aspettando il commento dell'ingegnere Dasaita.
Click to expand...
Click to collapse
Hello,
I have the same machine and the exact same problem, were you able to solve with Dasaita? what kind of solution did they propose to you?
i am trying to contact them
thank you

MarCern said:
Hello,
I have the same machine and the exact same problem, were you able to solve with Dasaita? what kind of solution did they propose to you?
i am trying to contact them
thank you
Click to expand...
Click to collapse
Hey,
sorry for late reply, but Dasaita "engineers" were not able to solve the problem. They sent me many Can bus adapters, but it did not solve the problem. I don't know where the problem is. They still talked me to cut the wire etc., change can bus etc. I am not mechanic, but I think that in the inner car software there must be something to change it.