Hi all,
I have tried to Hard SPL my S300+ (HTC P3600): I have used Olipro 1.20, OliPro 1.30 and Des' Crash-Proof SPL:
1/ I connect my device, run the Hard SPL tool, re-run it if I have the 264 error and the update begins.
2/ But the thing that is strange is that the update duration for me is 2 or 3 seconds instead of 10 minutes as specified.
3/ I reach the Congratulation screen.
4/ I think it's OK and I want to check but I did not manage to Manually enter the Bootloader by pressing the Power button, Camera button and performing a soft reset at the same time.
5/ So I run the Hard SPL a second time, the Bootloader screen (red green and blue) is displayed and here: HORROR: my SPL remains unchanged: I still have:
TRIN100
IPL-SSPL by Des
TRIN100
SPL-1.07.ds
What is wrong?
Thanks for your help
Wedikus
wedikus said:
Hi all,
I have tried to Hard SPL my S300+ (HTC P3600): I have used Olipro 1.20, OliPro 1.30 and Des' Crash-Proof SPL:
1/ I connect my device, run the Hard SPL tool, re-run it if I have the 264 error and the update begins.
2/ But the thing that is strange is that the update duration for me is 2 or 3 seconds instead of 10 minutes as specified.
3/ I reach the Congratulation screen.
4/ I think it's OK and I want to check but I did not manage to Manually enter the Bootloader by pressing the Power button, Camera button and performing a soft reset at the same time.
5/ So I run the Hard SPL a second time, the Bootloader screen (red green and blue) is displayed and here: HORROR: my SPL remains unchanged: I still have:
TRIN100
IPL-SSPL by Des
TRIN100
SPL-1.07.ds
What is wrong?
Thanks for your help
Wedikus
Click to expand...
Click to collapse
If you use the Hard-SPL tool to get into bootloader, you are loading a Soft-SPL before it actually gets to the bootloader screen. That's why you're getting the same info for SPL everytime.
To see the changes, you need to enter the bootloader manually.
BTW, it's normal that flashing an Hard-SPL only takes a few seconds, since it's not loading a full ROM into the device.
OK, thanks FInixNOver.
I have finally entered the boot loader, for information:
1/ press the Power button and the Camera button and leave them pressed
2/ perform a soft reset
3/ release the Power button and the Camera button
> you are in the boot loader!
Related
Please Help
I Have A P3300 And After Changing Rom (had Greek Rom) And I Put The Pdaviet The Pda Can Not Boot.
I Tried With Hard Reset To Make It Boot Again But Even If I Tried Several Times The Result Is Always The Same:
Ipl 3.04.0001
Spl 3.04.000.
Gsm 02.93.90
Os 4.0.0.0
And The Booting Stops There
Does Anybody Can Help?
LINANTONIS said:
Please Help
I Have A P3300 And After Changing Rom (had Greek Rom) And I Put The Pdaviet The Pda Can Not Boot.
I Tried With Hard Reset To Make It Boot Again But Even If I Tried Several Times The Result Is Always The Same:
Ipl 3.04.0001
Spl 3.04.000.
Gsm 02.93.90
Os 4.0.0.0
And The Booting Stops There
Does Anybody Can Help?
Click to expand...
Click to collapse
can you enter the boatloader?
Boot Problem
Unfortunately I Can Not Syncronize It So I Can Not Put The Boatloader
you can go into the bootloader by pressing the voice speed dial button and soft reset your device.
then you will get a 3 collor screen (red,green and blue). if you are in the screen connect your usb cable and you will have a connection so you can update the rom.
first use USPL and after that run the rom update utility
Thank You For Your Help
But I Did What You Told Me I Connected And I Start Running The Uspl.
Unfortunately The Spl Can Not Finish And Stuck Always In 50.
From 30 To 50 The Message Is :cant Spawn Cmd.exe.:no Such File In Directory C:
I updated my rom from the original spanish version to a Artemis_Touch_3.01
After some use, the device is blocked.
It starts the HArd reset, after "Format messages" It starts HTC white screen
IPL 3.13.0001
SPL 3.13.0000
and nothing more
.
It also works ROM update mode (Three colors screen) but when I execute the Rom update frommy pc, it reaches 2/3% and gives different Errors depending the ROM,
"Ivalid Vender ID [294] when I use the ROM HTC_P3300_SPA_3.13.412.1_4.1.13.44_02.94.90_Ship_R
ERROR [270]: Update Error -The Image File is corrupted - When I use Black & Blue 4.3 or Artemis_Touch_3.01
I need help!!!
brick?
hello,
First you must open the bootloader menu,
hold voice dial button and press soft reset.
If this not working hold voice dial and on/off button and softreset.
You must connect first your htc with your pc and the start the bootloader.
When you are in the bootloader menu, you can upload an orginal fabricrom to your htc.
Search xda-developer for the fabric rom.
And then you can change your rom for something else but don't forget the uspl.
When you want to change image you must install the uspl first otherwise everthing will blocked
the problem you have is that you have to run the uspl first before you can flash another firmware. If you run the uspl you will see that the spl loader of your device is version 1.11.000 and than you can flash an other rom of your choice
greetzz Patrick
uspl does not work. this is the point you can not get it.
have a problem but I cannot find anything useful for my case, maybe you can help me?
pvdhelm said:
the problem you have is that you have to run the uspl first before you can flash another firmware. If you run the uspl you will see that the spl loader of your device is version 1.11.000 and than you can flash an other rom of your choice
greetzz Patrick
Click to expand...
Click to collapse
Hi Patrick,
I have a dutch rom on my htc P3300
IPL: 1.12.0001
SPL: 1.12.0000
GSM: 02.67.90
os: 1.12.0.0
my HTC remains stuck on the startup screen (logo HTC) and will not get any further.
Connection with active synch is not possible, ans holding the buttons reset-voice rec-on/off buttons don't react. WM cannot be started in that way.
is it possible to find a boot program which allows me to start up WM again like a regular PC? something like a emergency startup disk? I have a 2GB micro SD card. After reading and trying so many things, I lost the way in this site and was hoping maybe you can send me some useful links that can solve my problem? I would appriciate the effort.I don't know if it's allowed to send my personal emailadress? If it is allowed please let me know. Maybe we can exchange directly some info, otherwise I don't have a problem mailing this site.
(I hope I can find this thread again after closing?)
Kind regards , Eli
my artemis is also in the same state
Hi All,
Please help me with problem which I am facing with my HTC P3300
When i switch it on..Its stuck in the state where it shows
IPL 3.07.0001
SPL 1.11.0000
GSM 03.08.90
OS 3.4.0.0
What I tried.
1. I tried USPL , its not loading as device is not getting detected in my laptop.
2. Volume Down+Reset is not working
Please help me with this
Hi there
The first time that I have attempted to perform the upgrade to a cooked rom and everything has gone horribly wrong.
A reset (using the pin hole) gives a blank display. Nothing at all.
A hard reset (using pin hole and soft keys) gives the option to perform hard reset by pressing Yes. This then gives HTC logo screen and then system hangs after displaying
IPL 3.13.0001
SPL 1.11.0000
I can go into bootloader screen (pressing two side buttons) and can connect USB. When I try to install factory ROM or any cooked ROM it stops at 2% and gives me an error saying
Error 228 - Invalid File Size
Is there anything I can do to save my device?
Please help.
are you sure that you have the right factory rom?
must be the one that was on your device when you bought it!
had the same problem! flashing with original rom solved it!
Yes - this is the WM5 rom that I had orginally before upgrading to WM6.
Bricked P3300
try and remove the minisd card
that must be the cause
cheers
jayzd1
Bootloader is not just by pressing two buttons. Press both the buttons and make a soft-reset. When the tri-color screen appears, connect to USB and perform the ROM upgrade again. If it fails, perform the upgrade with a factory ROM. This will bring back your device to working condition.
Next time before flashing, make sure you have applied Hard SPL once.
Regards,
Carty..
I have ( had ? ) a Diamond and tried for HARD SPL.
I was using Jump SPL for the first step.
The batch file had the following steps
REM SSPL for Diamond
REM credits: cmonex for doing wonderful relocation job
pause "Copy JumpSPL.exe to Diamond root directory"
cecopy JumpSPL.exe dev:\
pause "copy SSPL to Diamond root directory"
cecopy sspl-1.01-reloc-mod.nb dev:\
pause "execute SPL now - screen may trun black"
prun JumpSPL.exe 0x800000 sspl-1.01-reloc-mod.nb
pause "Now run DiamondCustomRUU.exe to flash HardSPL 1.24 (mfg) or HardSPL 1.23 (std)"
When I reached the last step , I wanted to execute DiamondCustomRUU.exe but it gave an error that I have to install ".Net Framework".
While installing .Net I had to install window installer first. I had to restart the computer.
But the ActiveSync got disconnected meanwhile.
I tried to reconnect the PDA but a hardware installation wizard appeared .... I don't know what to do with it ??
Now when I run DiamondCustomRUU --- It cannot locate PDA .
What should I do ??
Can you go to bootloader menu?
How can I check that , is there a tool !!!
I cannot start my PDA .... it is blank ( black ) screen after soft SPL.
Try pressing the volume down key and the reset button at the same time. That should get you into bootloader mode.
hold down button and press (red) reset button
manojeet said:
How can I check that , is there a tool !!!
I cannot start my PDA .... it is blank ( black ) screen after soft SPL.
Click to expand...
Click to collapse
Press soft reset button and volume down at the same time for about 3 4 seconds and if it goes to the 3 coloured stripes menu then its not bricked
or try to remove the battery for about 3 secs
The battery thing worked .... thanks a ton. I see my Diamond alive !!!
Also ActiveSync recognized it
But where is the RED button ???
I am very new .... but now if I want to try to Hard SPL again .... do I have to perform the Jump SPL step again or could I directly start with Hard SPL.
But Thanks for inputs once again.
The red reset button can be found if you remove the battery cover and take out the stylus. You will see a little red button that says 'reset' on the bottom left corner of the phone.
little red button
thats the soft reset button.....your hear it talked ablot alot on the forums
glad the phone is up and running again
Hi all,
I thought, lets install the new ROM (Macadam V1.2). So first I installed the HARD-SPL rom: SPL-1.30 Olinex erop gezet. (via this tutorial http://modmydiamond.info/index.php?option=com_content&task=view&id=12&Itemid=26&limit=1&limitstart=2)
After I installed the Olinex rom, i tried to install Macadam V1.2 (copied the .nbh to internal storage).
Then i pressed (Reset + Vol up + Back).
Then i got the loading.. screen for 15 minutes.
I thought it was stuck, and did a hard-reset: (via soft reset + Vol up + ENTER) -> Vol up
When i now start my TD, it freezes at the bootscreen (where u see TOUCH diamond) The red lettres of the rom versie wont appear.
I do can get in the red-green-blue-bootmenu
Does anyone know how to get my TD working again?
I'd love to have macadam v1.2 but first let my Diamond start normal again...
http://forum.xda-developers.com/showthread.php?t=504047
tnx very much. it works again. yay