Develop Bugs

HELP !!!!! After flash.... my Exec can't turn on....

Guys... please help
I download ROM IVAN beta7... then flash to my Exec...
The process looks goog... everything is fine...
After all is done... the I do hard reset (press both soft key+reset)... on screen appear press 0 to restore fact setting... then I press 0... after that
Nothing happen to my Exec... Screen is dark....
Then I reflash again, but the program says connection error... I think this is because my Exec is off...
Please help
Thanks

Try to reflash it. You should simultaneously press "Light" and "Power" button and reset it. Your screen will say "Serial" and when you insert USB cable it will say "USB". Then you should be able to run flash utility again.
Shishko

Finally works ...
Finally I can upgrade my Exec
I saw the thread at http://forum.xda-developers.com/viewtopic.php?t=59832
Thanks

Hard SPL completed but SPL unchanged!

Hi all,
I have tried to Hard SPL my S300+ (HTC P3600): I have used Olipro 1.20, OliPro 1.30 and Des' Crash-Proof SPL:
1/ I connect my device, run the Hard SPL tool, re-run it if I have the 264 error and the update begins.
2/ But the thing that is strange is that the update duration for me is 2 or 3 seconds instead of 10 minutes as specified.
3/ I reach the Congratulation screen.
4/ I think it's OK and I want to check but I did not manage to Manually enter the Bootloader by pressing the Power button, Camera button and performing a soft reset at the same time.
5/ So I run the Hard SPL a second time, the Bootloader screen (red green and blue) is displayed and here: HORROR: my SPL remains unchanged: I still have:
TRIN100
IPL-SSPL by Des
TRIN100
SPL-1.07.ds
What is wrong?
Thanks for your help
Wedikus

wedikus said:
Hi all,
I have tried to Hard SPL my S300+ (HTC P3600): I have used Olipro 1.20, OliPro 1.30 and Des' Crash-Proof SPL:
1/ I connect my device, run the Hard SPL tool, re-run it if I have the 264 error and the update begins.
2/ But the thing that is strange is that the update duration for me is 2 or 3 seconds instead of 10 minutes as specified.
3/ I reach the Congratulation screen.
4/ I think it's OK and I want to check but I did not manage to Manually enter the Bootloader by pressing the Power button, Camera button and performing a soft reset at the same time.
5/ So I run the Hard SPL a second time, the Bootloader screen (red green and blue) is displayed and here: HORROR: my SPL remains unchanged: I still have:
TRIN100
IPL-SSPL by Des
TRIN100
SPL-1.07.ds
What is wrong?
Thanks for your help
Wedikus
Click to expand...
Click to collapse
If you use the Hard-SPL tool to get into bootloader, you are loading a Soft-SPL before it actually gets to the bootloader screen. That's why you're getting the same info for SPL everytime.
To see the changes, you need to enter the bootloader manually.
BTW, it's normal that flashing an Hard-SPL only takes a few seconds, since it's not loading a full ROM into the device.

OK, thanks FInixNOver.
I have finally entered the boot loader, for information:
1/ press the Power button and the Camera button and leave them pressed
2/ perform a soft reset
3/ release the Power button and the Camera button
> you are in the boot loader!

Need desperate help with possibly bricked Diamond

Hi all,
Just received my Vodafone-branded Diamond, and I'm afraid I already managed to brick it!
It was equipped with version "1.37.172.3 NLD" so I decided to upgrade it to the latest version.
The installation of OliNex Hard-SPL 1.93 went flawless, but the installation of ROM "RUU_Diamond_HTC_WWE-ME_1.93.456.2_Radio_Signed_Diamond_52.29.25.12_1.00.25.05_Ship.exe" stopped at about 25% with error code 302. The recovery method that came with the package didn't help, every time the upgrade stopped at the same moment.
Since the device is stuck in the bootloader, and I'm left with a non-chargeable battery, I tried the official Vodafone-branded "RUU_Diamond_Vodafone_NL_1.97.172.4_Radio_Signed_Diamond_52.44.25.24_1.08.25.08_Ship.exe" ROM. Unfortunately, this upgrade stops at 48% and throws the same 302 error.
Anyone who can tell me what I'm doing wrong, and what I can do to solve all this?
I hope I don't have a brand new, but bricked device on Christmas!
TIA and have a nice day.

Try a hard reset first. If this doesn't help google or search at XDA for MTTY.
This tool can fix your device

http://wiki.xda-developers.com/index.php?pagename=Kaiser_Stuck_at_bootloader
Try this, maybe will work

Try a Vodafone branded stock rom before mtty.
Regards,
Carty..

He already tried a stock rom....

Potential Solution
Have you looked at the thread titled,
[UPG][TRBL]How-to fix: Update/Flash doesnt work, stops at 0% or 5% (invalid model ID)
It may just be a model ID glitch that can me fixed.
Take a look. It's in this forum in a sticky by cptsunshine.

Thanks all for the help, I'll have a look at your suggestions.
The problem isn't that it stops at 0% or 5%, it stops at random percentages (depending on the ROM I use).
I also see the bootloader (red / green / blue), so it's not dead. I guess it's just that it doesn't pick up a ROM.
Besides, the bootloaders says upgrade ROM code error please try again.
Edit:
A hard reset doesn't seem to work. In the bootloader, when I press "volume down" and "enter" together, and press the "reset button" the screen goes black, but then goes back to the bootloader screen after a sec or 2.
Edit 2:
MTTY doesn't do much either, after executing "boot" the phone is showing me the Vodafone logo and that's it.
For the rest, MTTY shows me the following:
Cmd>boot
InitDisplay: Display_Chip=1
dwDirectNum: 0, dwMatrixNum: 0, dwMicroPNum: 0
Fixed new dwPSImageSize = 0x53E0000

Install Rom via Internal Memory Method
Steps from Suiller:
1. open from your PC the rar or zip archive and extract only the BIG .nbh file
2. rename as DIAMIMG.NBH
3. copy the renamed file into the root dir of your "Storage Card" or "Internal Storage" (the one of 4Gb... NOT to the internal phone memory!)
4. reset your device and within 3 seconds push together the Vol_Down + Back button (the one on the right above the hangup button) and keep pressed until the boot loader appears (the one with the color stripes)
5. soon as you see the bootloader stop to press those poor buttons
6. a very simple gray menu will appear asking you what to do, simple press the power button to perform the ROM/Radio upgrade
7. while the upgrade runs be patient and don't press again the power button, reset the device or play with it until it finishes, when finished a message "UPDATE SUCCESS" will appear, now you can safely reset your device
8. who prefer can perform a hard reset after the fresh cook (soon after reset simply press Vol_Down + Circle button, then when you see another simple gray menu choose Vol_Up to confirm format), even if this has no-sense because internal memory is pre-formatted during flash, but... there is always a but... for some unknown "scientific" reason sometimes an hard-reset can save time & headache
Let me know how it goes.
Make sure you have Net framework 3.5 installed on devices.

Nakkie27 said:
Thanks all for the help, I'll have a look at your suggestions.
The problem isn't that it stops at 0% or 5%, it stops at random percentages (depending on the ROM I use).
I also see the bootloader (red / green / blue), so it's not dead. I guess it's just that it doesn't pick up a ROM.
Edit:
A hard reset doesn't seem to work. In the bootloader, when I press "volume down" and "enter" together, and press the "reset button" the screen goes black, but then goes back to the bootloader screen after a sec or 2.
Edit 2:
MTTY doesn't do much either, after executing "boot" the phone is showing me the Vodafone logo and that's it.
For the rest, MTTY shows me the following:
Cmd>boot
InitDisplay: Display_Chip=1
dwDirectNum: 0, dwMatrixNum: 0, dwMicroPNum: 0
Fixed new dwPSImageSize = 0x53E0000
Click to expand...
Click to collapse
u can do one thing then press woluem down and reset bottom at the same time then u go to rescue mode then u wait and put in the usb stick and there stand seriel when u put in the cable it will change to usb thenu can load the firmware again

band27 said:
Steps from Suiller:
3. copy the renamed file into the root dir of your "Storage Card" or "Internal Storage" (the one of 4Gb... NOT to the internal phone memory!
Click to expand...
Click to collapse
I wish I could mate, but I cannot put files on it anymore, since ActiveSync doesn't recognize my device when it's in the bootloader.
janielsen said:
u can do one thing then press woluem down and reset bottom at the same time then u go to rescue mode then u wait and put in the usb stick and there stand seriel when u put in the cable it will change to usb thenu can load the firmware again
Click to expand...
Click to collapse
Can you please be more specific? Are you telling me how to do a hard reset? I tried as to do a hard reset, but it goes back to the bootloader instead of resetting. USB stick?
Thanks all, much appreciated. A pain this can happen, looking at the fact that I did everything exactly as described in all these flashing manuals.

Nakkie27 said:
I wish I could mate, but I cannot put files on it anymore, since ActiveSync doesn't recognize my device when it's in the bootloader.
Can you please be more specific? Are you telling me how to do a hard reset? I tried as to do a hard reset, but it goes back to the bootloader instead of resetting. USB stick?
Thanks all, much appreciated. A pain this can happen, looking at the fact that I did everything exactly as described in all these flashing manuals.
Click to expand...
Click to collapse
first push the volum down buttom at the same time press the reset buttom then the 3 color display will appear and in the buttom will stand seriel then u putt in the usb cable to ur phone whit u have attact to ur pc then it will say usb now u can load new firmware

janielsen said:
first push the volum down buttom at the same time press the reset buttom then the 3 color display will appear and in the buttom will stand seriel then u putt in the usb cable to ur phone whit u have attact to ur pc then it will say usb now u can load new firmware
Click to expand...
Click to collapse
No mate, I never had problems getting into the 3 color screen. The problem was updating afterwards, which never completed without error code 302.
Anyway, I guess I just fully bricked my device after putting SPL-1.40.OliNex (according to the guide at http://forum.xda-developers.com/showthread.php?t=416211) on it. The SPL install was succesful, but when booting I'm now not even getting to see the 3 color bootloader. All I see is the Vodafone logo with some version numbers at the bottom, but that's it. It doesn't boot further on, and I can't get a USB-connection.
Edit:
Volume down + reset brought me in the bootloader again, although it's saying SPL-1.93.OliNex.

Nakkie27 said:
No mate, I never had problems getting into the 3 color screen. The problem was updating afterwards, which never completed without error code 302.
Anyway, I guess I just fully bricked my device after putting SPL-1.40.OliNex (according to the guide at http://forum.xda-developers.com/showthread.php?t=416211) on it. The SPL install was succesful, but when booting I'm now not even getting to see the 3 color bootloader. All I see is the Vodafone logo with some version numbers at the bottom, but that's it. It doesn't boot further on.
Click to expand...
Click to collapse
that i know but as i say in the post that when u do it that way i say u can load new firmware whitout it needs to boot try my friend i have done it 3 times because wrong loading of firmware

u have to only push thoose 2 buttom then it will work because u go to rescue mode

But what will that give me extra? I can access the Hard-SPL 1.93 bootloader (3 color screen), and I can get into USB mode. It's just that the upgrade of both firmwares stop at a certain percentage.
I'm constantly trying to hard reset the device, but after pushing the reset button (with both volumn down + enter pressed down), the device just reboots back into the bootloader and doesn't give me the hard reset warning.

Nakkie27 said:
But what will that give me extra? I can access the Hard-SPL 1.93 bootloader (3 color screen), and I can get into USB mode. It's just that the upgrade of both firmwares stop at a certain percentage.
I'm constantly trying to hard reset the device, but after pushing the reset button (with both volumn down + enter pressed down), the device just reboots back into the bootloader and doesn't give me the hard reset warning.
Click to expand...
Click to collapse
u need to hold them down until it leave the 3 color display an turns into grey

Ok, finally managed to do a hard reset. Afterwards I tried upgrading to the official Vodafone NL 1.97 ROM once more, but it failed at 48% again.
Any ideas what to do? I know have Diamond with Hard-SPL 1.93 (which says upgrade ROM code error) with no working OS.

Ok all, got it finally working again!
Don't ask me why, but flashing the newest Dutty ROM (and the included radio) did work.
Thanks for all your help, and a wonderful evening!

Hi all,
I have a quit similar problem. I've read a lot, but couldn't find an answer to my problem - may bye someone can help me.
I updated my Dimond (OliNex Hard-SPL 1.93, radio 1.09.25.23 and rom dutty V4). When I start my phone most of the time (95% plus) I end up in the color screen - however some time it's starts perfect (without changing anything).
When I get stock in the color screen, I can start the phone with mtty and the command "boot".
What can I do to make my phone always start in the normal way?
Thanks!

Nakkie27 said:
Ok all, got it finally working again!
Don't ask me why, but flashing the newest Dutty ROM (and the included radio) did work.
Thanks for all your help, and a wonderful evening!
Click to expand...
Click to collapse
i smell a radio issue - last time i was trying to upgrade my radio - ended up with something similar, managed it out like you did - but now you're up - so that's good!!
try some other rom (this time without radio) - i don't think you should have any issues going forward... good luck and have fun!

Help htc touch diamondtive sicron.

Hay i have htc touch diamond how to uptade wm 6.1 to 6.5 ? I try to connect wia active sicron. But cannot uptade

[link 1], [link 2]
Link 1 is the same thing with link 2.

Tanks on fasst answer i got 4 colors screen , red ,yelow , blue ,white on top writte diam100 64m spl-1.37 i pressing power button nothing happening ,help . I new one here

Connect your diamond to PC as a disk drive (mass storage) and copy your ROM to Internal Storage. Make sure it`s name is "DIAMIMG.nbh" (*.nbh is the extension, make sure it is only once, not like this: "DIAMIMG.nbh.nbh" ) and than hit the reset button and hold vol down + back key. After update make a hard reset, hit the reset button and hold vol down + center key and follow the instructions on the screen (vol up to format only phone memory).
I hope you understood.
Good luck!

This part is ok now writte "trigger usb host " noting happend but i clean f disk ( memory internay ) only left image file how to run update ?

So... put "DIAMIMG.nbh" into Internal Storage (root). Unplug you diamond from PC, hit the reset button, and hold vol down + back key, press power key, wait for update to complete.

thecrazyman64 said:
So... put "DIAMIMG.nbh" into Internal Storage (root). Unplug you diamond from PC, hit the reset button, and hold vol down + center, press power key, wait for update to complete.
Click to expand...
Click to collapse
Vol down + the back button

i did do this go info no image file i have version 1.37 what rom i must use ?Even to update windows to 6.5 english

Tajanstveni said:
i did do this go info no image file i have version 1.37 what rom i must use ?Even to update windows to 6.5 english
Click to expand...
Click to collapse
Just going by my Diamond and what you said in a previous post, it should say (quoting my diamond) "SPL-1.24. Hard"
You can't flash custom ROMs with a stock SPL.
Link for HSPL is in here, read along with it.

I tray to download renamed it put in root but when start loading file mising image file writte why?

Tajanstveni said:
Hay i have htc touch diamond how to uptade wm 6.1 to 6.5 ? I try to connect wia active sicron. But cannot uptade
Click to expand...
Click to collapse
please read this - http://forum.xda-developers.com/showpost.php?p=2508373&postcount=1
its one of the basic things we do... and you will get most of answers here...
this is 3rd topic on the forum for diamond - http://forum.xda-developers.com/forumdisplay.php?f=430
you can see other useful posts as well.... MTTY is highly recommended when you flash new rom to diamond...

Tanks for asnswer fast but problem is that i cannot conect device with pc when i start diamond ruu program later i get error 224 What i need some drivers for reconect to pc? I use microsoft active sycn 4.5 but i cannot coneect completly come message on display . Exist another method to connect touch diamond to pc ?

After factory default reset and format internal storage now is problem when i try to start rom uptadte from internal storage writte "loading ...." i wait more that 10 min nothing happend only loading.... where is the pronlem

Tajanstveni said:
After factory default reset and format internal storage now is problem when i try to start rom uptadte from internal storage writte "loading ...." i wait more that 10 min nothing happend only loading.... where is the pronlem
Click to expand...
Click to collapse
If you can connect to activesync (should be possible, since you are back to original),
use the customRUU method. At least that should give an idea of where the process is getting wrong, plus will allow recovery.
HTH...

Same Problem?
Tajanstveni said:
Hay i have a problem wih htc touch diamond when i tray to connect to pc with active sync 4.5 said that device cannot be sicnoized completly and i cannot update costum rom come error 224 device not found ,can anibody help me ?
Click to expand...
Click to collapse
Looks like you created a new thread for the same problem...
http://forum.xda-developers.com/showthread.php?t=643159

Sorry for my mistake but probolem solved ,tanks for help

After MTTY, HTC freezed!!!

Please help me with this issue! (Device HTC touch diamond P3700)
I was following the the post The DEFINITIVE MTTY Thread!! REVISED 02-11-09 and now my HTC is dead. This is what I have done:
HardSPL 1.40 OliNex
Driver Signature Enforcement Overrider
Remove Watermark V0.8
x86 Active Sync Drivers (using windows 7)
Download the ROM, rename to DIAMIMG.nbh, save in Internal Storage, not in any folder.
comes to Mtty:
Press enter for CMD>
type set 14 0
type task 29
type task 8
(I think this is where the problem is)
Immediately DISCONNECT your device and hold "Vol Down and Back" (Back = Small Arrow above "End Call" Button) to Initiate ROM Flash
I did it when the TOUCH DIAMOND logo displayed on the screen, on the computer was at the CMD> displayed after CMD> task 8.
but my HTC just freeze at the TOUCH DIAMOND forever, nth like ROM flashing happened, never boot into windows mobile, I did soft reset and hard reset, didn't solve the problem.
Everytime I switch it on, it just stays at TOUCH DIAMOND, so what did I do wrong and how to bring my HTC touch DIAMOND back to life please?
Many thank very much in advance!

luckyvictor said:
Please help me with this issue! (Device HTC touch diamond P3700)
I was following the the post The DEFINITIVE MTTY Thread!! REVISED 02-11-09 and now my HTC is dead. This is what I have done:
HardSPL 1.40 OliNex
Driver Signature Enforcement Overrider
Remove Watermark V0.8
x86 Active Sync Drivers (using windows 7)
Download the ROM, rename to DIAMIMG.nbh, save in Internal Storage, not in any folder.
comes to Mtty:
Press enter for CMD>
type set 14 0
type task 29
type task 8
(I think this is where the problem is)
Immediately DISCONNECT your device and hold "Vol Down and Back" (Back = Small Arrow above "End Call" Button) to Initiate ROM Flash
I did it when the TOUCH DIAMOND logo displayed on the screen, on the computer was at the CMD> displayed after CMD> task 8.
but my HTC just freeze at the TOUCH DIAMOND forever, nth like ROM flashing happened, never boot into windows mobile, I did soft reset and hard reset, didn't solve the problem.
Everytime I switch it on, it just stays at TOUCH DIAMOND, so what did I do wrong and how to bring my HTC touch DIAMOND back to life please?
Many thank very much in advance!
Click to expand...
Click to collapse
you have to flash a rom...open the diamond in bootloader mode and start RUU from the pc
edit:i didn't read that you have flashed a rom...

So when you do a soft reset while holding Vol-Down only, does it boot to the screen with color bars when it says TOUCH DIAMOND? Or is it a splash screen? Or just text on a blank background?
If it's the color bars, you should be able to reflash via USB.
If it's a splash screen, you're not holding the Vol-Down properly (or fast enough) when resetting. Try holding Vol-Down before reset.
If it's a blank background, I have no idea what you can do.

Now, for some reason, I managed to bring it back to working condition by flashing the OFFICIAL ROM.
and now I would like to flash the ROM I download from this forum.
so after task 8 in mtty, what should I do really? should I press the keys after the CMD> pops up? or should I press the keys before CMD>?
Many thanks for the advices

after task 8, basicly you should do 3 steps at once !
1. pres enter in mtty program to initiate reboot
2. disconnect phone from usb port
3. press (and HOLD!) vol down and back arrow until flashing starts (ofc if ROM you wanted is in internal storage called diamimg.nbh)
after this phone will say press power button if you are sure, of course you are, you dont have rom!
just sit and wait

Yup, follow vicai's steps exactly. It kinda sounds like you didn't press enter after typing task 8.
As long as you press vol-down and back while the screen is still black during the reset, you're fine.