Greetings,
I hard-reseted my Artemis device operating with WM 6 to clean my registry. After the reset, I couldn't get the device to connect to the Internet, neither using WiFi (although connection is fine), nor GPRS (settings are fine)!!
I get the following message: "The page cannot be displayed or downloaded because the connection was lost. Check the connectin and try again later."
Anyone had this problem before?
Cheers,
Ahmed
try another hard reset
or cut the long story short and just re flash your rom
run windows\welcome.exe, pass the calibration, and try again
Related
since installing radio 1.13 i have not been able to connect to GPRS using wap.voicestream.com. this is after a hard reset with none of the EXT rom tools loaded. i try to connect, and it times out. in 1.12 i would be able to connect once but after connecting to activesync or disconnecting GPRS i was not able to log back in unless i soft reset or turned on flight mode then turned it off. I have 1.40 ROM installed with phone alarm 1.21, pocket plus, and wisbar 2.4.11
UPDATE!!!
ok, i uninstalled pocket contacts 1.1 from www.pocketx.net and installed pocket conctacts PRO 3.0. i also unloaded mort ring. well when i did that i was not only able to connect to gprs, i am now able to RECONNECT when i disconnect! wierd...
What device do you have and what ROM are you running? I'm looking to solve this problem on my PDA2K.
i have the same device and ROM as you do. since i last posted. i am only able to connect to GPRS after a soft reset, not turning on/off flight mode
Downgrading Caller ID to IA_CallerID_1.20_WWE.CAB will fix this problem. It worked on mine at least...
downloading and installing the cab for the caller_id worked for mine as well. i've had no problems with gprs connections since performing the downgrade -- which was a little over a week ago. i think you can find the cab in these forums if you search for it.
i dont have that caller id sodtware installed at all and i still have the gprs reconnect issue
Tried the 'g' hack to get recognised on wifi G only networks and now my wifi won't connect to anything.
Uninstalled the cab from add/remove programs, but I'm still stuffed.
Can anyone help with a suggestion or the original registry values for the wifi?
I originally did it via the hack compiled in cab form, then manually set the registry via the msmobiles site, then tried another suggestion - only joy I have is seeing but being unable to connect to any network.
Before it was 'fussy' anyhow, not wanting to connect to some networks and I was hoping to improve it's connectivity to include those set to G only.
Help...
Try hard resetting your phone, this should restore the original settings fully and it should work again.
Tried that, no difference. Also after hard reset (0) my boot loader splash screen is still the same (customised) and I am now unable to upgrade the rom it seems. Tried what I did before, only switching to the CE from my original O2 rom, and it examines device ok, disconnects it ok, restarts it when the device boots up and the rom upgrade utility sits at 'do not turn off' doing nothing....
Update, put device into boot loader mode, flasher now worked, re wrote the rom and setup again, now wifi works again. Long way round hey, even hard reset didn't work!
Hello,
first of all, i want to thank you all for this great forum.
I have a small problem. I have bought a few days a HTC P3600. Everything was working fine.
Yesterday i tried to upgrade to wm6 using MARY 3.4.1 with sucess following the upgrade guide in trinityguides.info.
I have installed the Des’ Crash-Proof SPL and then flash the MARY 3.4.1 ROM.
Until now everything is working fine except the active sync. I tried to AS with the usb cable but it won't connect. It gives me the following error:
"Communication Error:Cannot start communications with the desktop computer. Remote Networking could not start due to a critical error (Error 608). Please reconnect your device. If the problem persists, restart your device using the instructions provided by the manufacturer."
I've googled it and tried all the suggestions that i could find, with no success.
If i connect via BT there is no problem.
The problem is that i want to put back the official ROM from HTC and if i can't connect with active sync via usb, i can't restore it.
BTW, if i put back the official ROM, the Hard-SPL is also flashed to the original??
Thank you
cabexas said:
Hello,
first of all, i want to thank you all for this great forum.
I have a small problem. I have bought a few days a HTC P3600. Everything was working fine.
Yesterday i tried to upgrade to wm6 using MARY 3.4.1 with sucess following the upgrade guide in trinityguides.info.
I have installed the Des’ Crash-Proof SPL and then flash the MARY 3.4.1 ROM.
Until now everything is working fine except the active sync. I tried to AS with the usb cable but it won't connect. It gives me the following error:
"Communication Error:Cannot start communications with the desktop computer. Remote Networking could not start due to a critical error (Error 608). Please reconnect your device. If the problem persists, restart your device using the instructions provided by the manufacturer."
I've googled it and tried all the suggestions that i could find, with no success.
If i connect via BT there is no problem.
The problem is that i want to put back the official ROM from HTC and if i can't connect with active sync via usb, i can't restore it.
BTW, if i put back the official ROM, the Hard-SPL is also flashed to the original??
Thank you
Click to expand...
Click to collapse
Try an other usb port on your computer.
And yes, offical rom restore everything (ipl,spl,radio,os)
I have already tried that.
The only thing that i can remember that i didn't tried, is connect in a different computer, but i will try that as soon as i get home.
thanks
try another ROM. got that activesync issue also with every Mary ROM.
You can find it in UDK rom thread
Active Sync Error 608
Try this to solve the problem:
Quote:
Originally Posted by nanni100
I solved cause my Windows Firewall was damaged and not customizable, then i found a reg file to solve this problem, installed on pc and reboot. On startup i saw the window of Win Firewall who asked me to unlock Activesync i said yes and turn off the firewall
I have a ethernet router with DHCP enabled
Then i configured the phone:
-Enabled Advanced Netword Function
-Go on Setup, Wi-Fi, Network, Remote HOST- NDIS
-Select the Specific IP Address like this:
IP Add: 169.254.2.1
Sub Mask: 255.255.0.0
Gateway: 169.254.2.2
and on the other page put only on the first DNS: 169.254.2.1
on the pc lan connection i leave the dhcp enabled "Obtain IP Address from serv" also for DNS (obviously cause i have the DHCP enabled on my router)
And MAGICLY all start works FINE!!!
After hours and hours spent on configurations, the problem was "simply" the windows firewall, but also the configuration of Remote Host-NDIS is important
Hope that can be useful for other
Right now i don´t have the MARY rom but the TUGA V3 ROM and problem continues. I have already tried to setup Remote HOST- NDIS like that and it didn´t work too.
Anyway thanks for all your help.
Thanks
Use the SD Card Method...
I use the SD Card Method. MUST BE FORMATTED AS FAT32 first. (As per willowxda's post. Thanx Willowxda)
Copy SSPL_TRIN.exe to your SD card's Root folder. (Included in ZIP File)
Rename the RUU_signed.nbh file in your OEM Rom to TRINIMG.nbh
Copy TRINIMG.nbh to your SD card's Root folder.
Run SSPL_TRIN.exe from your device.
Allow it to Flash and Restart as needed.
Works like a charm...
cabexas said:
Hello,
first of all, i want to thank you all for this great forum.
I have a small problem. I have bought a few days a HTC P3600. Everything was working fine.
Yesterday i tried to upgrade to wm6 using MARY 3.4.1 with sucess following the upgrade guide in trinityguides.info.
I have installed the Des’ Crash-Proof SPL and then flash the MARY 3.4.1 ROM.
Until now everything is working fine except the active sync. I tried to AS with the usb cable but it won't connect. It gives me the following error:
"Communication Error:Cannot start communications with the desktop computer. Remote Networking could not start due to a critical error (Error 608). Please reconnect your device. If the problem persists, restart your device using the instructions provided by the manufacturer."
I've googled it and tried all the suggestions that i could find, with no success.
If i connect via BT there is no problem.
The problem is that i want to put back the official ROM from HTC and if i can't connect with active sync via usb, i can't restore it.
BTW, if i put back the official ROM, the Hard-SPL is also flashed to the original??
Thank you
Click to expand...
Click to collapse
it is very simple but it took me too long time to figure out.
My PC hangs several times, I thought it is related to DMA or to IRQ interrupt requests for the microproccessor, but failed to solve it. This problem never happened to me while I was having the Qtek ppc, and even when I used the official HTC ROM when I bought this TrinTy. Then I started to check everything related to USB connection till I catch it. it is very silly, just to clear one checkbox.
Here what worked for me:
Click Start > Settings > Connections > USB to PC
you will find a checkbox......Just uncheck it. --------> Thats to disable advanced network functionality.
I believe it should work for you.
Try POWER + CAMERA + SOFTRESET (this enter the bootloader mode) and then install the ROM you like ... you will get no errors !!!
Click Start > Settings > Connections > USB to PC
you will find a checkbox......Just uncheck it. --------> Thats to disable advanced network functionality
Click to expand...
Click to collapse
That was the first things that i tried to do, but with no luck.
Yesterday, i did what nightfear suggested and it worked fine.
As soon as i restored the official rom, AS started to work like a charm.
That is a strange issue, but for now it's resolved.
Lets see if the problem doesn't come back when i put WM6 on it again.
Thank you all for your help.
Mini SD card must be formatted in FAT32 for flash update to work
I have been trying to upgrade flash via SDCard but it did not work no matter how hard I tried (switch btw hardspls).
Then I realised that I have to format the SDCard to FAT32 so that the Hard SPL can recognise the card in bootloader prompt.
I am using Hard SPL 1.30
I've searched but can't find the answer to this one - sorry if I've missed it somewhere. I have an unmolested T-Mobile UK MDA Vario 2 and I'm trying to install the official TM UK WM6 upgrade ROM.
On my desktop PC (which is properly paired to the phone through ActiveSync to sync with Outlook etc) running the exe results in a grey box with red text saying "Checking files on your PC" forever unless I unplug the phone. Then it will eventually launch the wizard. If I plug the phone in again and wait until it's synced and "Connected", the wizard will go all the way through to checking the existing version and starting the upgrade. However, when the upgrade starts the progress bar stays at 0% and the phone turns off!! Eventually it times out with a 260 error, and no changes have been made to the phone. The PC is running XP, but the only fixes I've seen for the 260 error are if you're running Vista?
I've also tried on my XP laptop - this isn't paired, so the connection through Activesync is just as Guest. The update still does the strange thing with the "Checking files on your PC" box if the phone's plugged in, but unlike the desktop PC the RUU won't talk to the phone at all - connection error before it can even verify the existing ROM version.
Can anyone help? I've been waiting for months to get WM6!
Cheers,
Tim
Phone just turns off?
OK, so now I've done a hard reset on the phone, paired it up to my XP laptop and told it not to sync anything. Now I get to the same stage as I do on the desktop - i.e. the phone switches itself off when the upgrade begins (at 0%), then the RUU times out with an error 260!
One odd thing I noticed is that if I plug the phone in with "Advanced network functionality" enabled (which it is by default) the PC tries to connect it as a new 10mb network card!? However, the RUU does the same thing whether this is enabled or not.
Getting desparate for help now - I've tried 2 different machines and even cleared the phone completely, what more can I do?
Cheers,
Tim
Try flashing from an sdcard. There are quite a post on it here, if you do a quick search you should be able to find the information and hopefully get your device upgraded.
It might be worth installig spl V7 from here before hand just in case anything goes wrong.
http://forum.xda-developers.com/showthread.php?t=296722
Working!
Thanks for the reply. Finally got it flashed using the instructions from here:
http://forums.cingular.com/cng/boar...thread.id=42389&view=by_date_ascending&page=1
Basically, you have to:
- Connect using Activesync and let it finish syncing.
- Start RUU.
- Activesync will close - ignore it and carry on.
- Eventually the phone will go into debug mode.
- Continue through the wizard - it won't be able to identify the existing rom version but this seems to be normal.
- Let it finish!
I was fiddling when Activesync closed - strangely, by disconnecting, restarting AS and reconnecting the wizard carried on and even identified the existing rom properly! It seems that it needs AS to connect to the phone initially, then it closes AS but keeps the USB connection open for the update.
Hope that helps anyone else with the same problem.
Cheers,
Tim
Just got my rhodium today (t-mobile branded unfortunately), it's a great device. Just one weird problem i am having with activesync, maybe someone knows what the problem is.
After installing activesync it works fine, untill I turn off (restart) my computer, then as soon as a connect my rhodium it tries to intialize the connection but gets an error. On the device it says, error with rapiclnt and asks me to send the error log to Microsoft. When i run the active sync troubleshooter it says that connection with the device cannot be established and over some suggestions (stop firewall,enable usb connection).
So far the only thing that fixes it, is uninstalling and reinstalling activesync. It then works fine untill i restart.
Things i have tried that have not worked are:
1. Hard reset the device
2. Soft reset the device
3. Deleted partnerships on both computer and device
4. Removed firewall
5. Unchecked advanced network functionality
The only other thing I can think of is to formate my pc and do a complete fresh install of windows xp. If nothing else this should rule out the problem is on the pc end I think.
Any suggestions are appreciated, thnx in advance.