i have i-mate pda2k and i have installed wm5 on my device and i want to downgrade it to win2003se .
my problems :
1- the soft reset button are broken .
2. i haven't downgrade to win2003se.
please help me quickly
big boss, you may want to go back to you initial post and change the title to "How can I downgrade from WM5 to SE2003 without reset button" and you may get some help.
yup... just like Free888 said.
the alternative is to flash using a USB cable and NOT a cradle.
which makes the battery and the notch accessible.
you could release the notch to turn off, then lock it again + power button to turn on.
Related
Hello! i would like to upgrade my xda 2s do wm2005 xpload and i have read wiki to! but really don't know how looks like bootloader mode! i pressed on/off, camera button and reset and nothing was happend, mda was reset and that is it! upgrade program do not see current software etc! can anyone can help me with that " by hand" please! first time is always hard! please! cheers Jocker01
Well, have you tried "Record"-button instead of "Camera"-button?
(Press and hold "Record", "Power", and "Reset" until bootloader comes up)
hello thx! finally i get bootloader mode, i've pressed camera, record, on/off and reset buttons! i hope so this is bootloader mode( THX Smokkky ). on screen i have dispelyed usb and v2.07. but ultility still dont update rom! cheers Jocker01
Hi all
I have a problem with my PDA (Qtek S200)
IPL 2.10.0001
SPL 2.G4.4PDA
GSM 02.69.21
THE 7.0.0.7
And it is this:
Made a backup of my contacts over SPBackup, did the flash ROM of everything he turned to run normally, I made the restores the contacts and SMS, ... and when it does reebot it is only by the initial image that presents the data above:
IPL, SPL, ...
We have tried to make the soft-reset (pen of the button and the small button on the camera and nothing)
My question: Does anyone know how solve this?
Best Regards and thanks
Bye
Anybody help me ?
Please it's very urgent...
thanks all
can you do a hard reset using the keys and see if that allows the device to boot again ?
reading your post again, i assume that is what you are trying to do with the camera button when resetting, hmmmm
Ok, if i were you, i would try this next.
Enter bootloader mode by doing the following
To enter bootloader, you need to hold the comm manager button and soft reset
If that allows you to enter bootloader, then try reflashing the rom
let us know how you get on after that.
also it might be worth posting in the forum for this device, if you havent already.
hard reset.....To perform a hard reset
Z3nD3n said:
Hi all
I have a problem with my PDA (Qtek S200)
IPL 2.10.0001
SPL 2.G4.4PDA
GSM 02.69.21
THE 7.0.0.7
And it is this:
Made a backup of my contacts over SPBackup, did the flash ROM of everything he turned to run normally, I made the restores the contacts and SMS, ... and when it does reebot it is only by the initial image that presents the data above:
IPL, SPL, ...
We have tried to make the soft-reset (pen of the button and the small button on the camera and nothing)
My question: Does anyone know how solve this?
Best Regards and thanks
Bye
Click to expand...
Click to collapse
To perform a hard reset
* Press and hold the CAMERA and COMM MANAGER buttons, and at the same time, use the stylus to press the RESET button at the bottom of your device.
Hello again ...
I am happy. Have back by my Qtek. had already done several times the Hard-Reset the PDA but always without success. I often followed and there began to anything on screen (the 3 colored bars, then asked the question of "send ..." where we have to press the green button "call") and then there came into bootloader and there could . He began to install everything right and it was if he had installed a Rom "new".
To all those who contributed to this "happy ending" my thank you very much.
sry my english
Bye and thanks
EDIT: I fixed it!!
I ran into a very old thread here....
I entered the bootloader and I flashed an official rom, after I downloaded it
I will keep this rom as a security from now on!
----------------------------------------------------------------------------------------------------------------------------------------------------
Hi everyone,
I have been enjoying all the roms you all gave to use many many years now.
Also I have been able to flash them without any problems....However this morning.... I was flasing a new version and during the flashing I knocked my phone of my usb-cable..... OUCH....
I am now trying to find a way to rectify this again, because now it will not boot, not recover, no nothing.
When I am in bootloader I cannot flash any roms (I have tried 7 different roms)
My Artemis P3300 is fully unlocked, but I cannot connect to active sync, nothing.
Will someone please guide me in how I can recover my phone and flash a rom again?
Can't do anything anymore, other then enter the bootloader, but flashing any rom will abort after 3%
Please be so kind as to help me out.
Thank you very much
Gianna xxx
--------------------------------------------------------------------------------------------------------------------------------------------------
repair frozen wm/ppc & flash rom again
just press the voice command & power button together[/B] and keeping the two button pressed together press the reset button together and then leave the reset button but continue keep pressing the voice dial & power button until the 4 band / 3 band colour mode appears.
( the reset button is found in a very small hole / but be careful , donot get confused with the microphone hole ).
when this 4 band / 3 band colour appears connect the active sync wire an connect to the computer.
you can find that in the mobile screen it will appear as usb.
i have really recovered my frozen htc p3300/ dopod p800 w
really thanks to xda developers... they are really genious/marvellous..
they can really do any thing ... three cheers to them.
hats off to them.
First thank's for four help and read this thread.
The problem is:
My exca100 the last week work fine but the monday the exca reboot and frezeeng in green WM screen, i leaves it all night but it does not continue.
I try reflashing but the problem is, the image is corrupted (I cant unlock the exca, so that it does not initiate windows)
Can any one help me.
ONLB 1.30.0000
SPL 1.30.0000
Brightstar shiped 1.30.514.2
labtelcel said:
First thank's for four help and read this thread.
The problem is:
My exca100 the last week work fine but the monday the exca reboot and frezeeng in green WM screen, i leaves it all night but it does not continue.
I try reflashing but the problem is, the image is corrupted (I cant unlock the exca, so that it does not initiate windows)
Can any one help me.
ONLB 1.30.0000
SPL 1.30.0000
Brightstar shiped 1.30.514.2
Click to expand...
Click to collapse
what do you mean by( I can't unlock the exca)?
Hard Reset
Hard Reset will most likely solve the problem. I had the same problem.
TO HARD RESET:
-Turn off the phone
-Hold 2 soft keys
-press the power button for 3-5 seconds(still holding two soft keys)
-black screen will show up saying that pressing send key(green) will restore your settings to original settings.
-press send(still holding two soft keys)
-the end.
NB: YOU'LL LOSE YOUR PHONE'S DATA.
For Hard-Reset see sticky "a picture tells a million words"
The hard reset dont work, frezz in HTC screen I wait 2 hrs.
I dont want unlock, I want normal funcions.
labtelcel said:
The hard reset dont work, frezz in HTC screen I wait 2 hrs.
I dont want unlock, I want normal funcions.
Click to expand...
Click to collapse
Don't understand bolded?
You have tryed Hard-Reset not work, remove battery for about 5 mins and replace, try again "Normal boot then if not work try Hard-Reset"
Sorry for my poor english, Im from mexico.
I try the master reset many times it does not work, of several ways, extracting the battery for 5 minutes, 1 hr, 3 days, and it does not complete the reset, freeze in the htc screen, or another times in windows mobile logo screen.
When attempt to change the flash (for solving the problem) the process does not continue of 3%, this happens so I cant execute the jump USPL aplication.
In summary:
reset hard not work (hold 2 soft keys / turn on / black screen / send key)
Change the Rom for repair de damage not work (I cant load the aplication for jump USPL)
Write Rom direct in the bootloader (3 color screen) not work (hold camera button and tur on)
Any idea?
Change bootloader?
Another powerfull rom?
Special software?
Special combination to delete all in the internal memory without entering Romupdateutility locks or windows?
Please helpme to recover my excalibur.
this is so easy to fix,
your old rom now crashed, hardreset can't help you,
to repair,just download a new rom then open bootloader mode.
boss_of_any_phone said:
this is so easy to fix,
your old rom now crashed, hardreset can't help you,
to repair,just download a new rom then open bootloader mode.
Click to expand...
Click to collapse
Just shows sometimes can miss the obvious, bootloader in sticky & flash original ROM in stickys too..
Dont work the reflash in bootloader (try 10 times), I flash the rom and the phone frezz in the same screen (WM logo screen).
Help.
Hello, this is my first post here. I tried to install Windows Mobile 6.5 as indicated in Gizmodo http://gizmodo.com/5281397/how-to-install-windows-mobile-65-right-now but it didn't work and now my phone won't boot.
The phone is an HTC Touch Diamond from Sprint. I followed all the steps indicated and everything look fine, but after installing the OS the phone displays the screen TOUCH DIAMOND, and then restarts and displays the same thing. I'm able to get into the boot loader (Tri color screen) and says:
DIAM500
SPL-0.57.CMONEX
MicroP-Diam (LED) vB
PSOC-Diam STAGE_EVT v20.
I don't know what to do now
Thanks
try to load back to default setting by pressing the power on button at the top of the phone, before the "Touch Diamond" logo come up, press and hold volume down button and the center button until the three color screen come out, then release the two button you are pressing..
if the problem still happen, that mean the rom you are using should have risk on it..
give it up and try other rom or flash it again..
hope my suggestion can help you solve the problem..
dont worry.
if bootloader is possible as you write
than you can flash all time orig. rom back.
Flash from Olinex 1.40 screen?
okokur said:
dont worry.
if bootloader is possible as you write
than you can flash all time orig. rom back.
Click to expand...
Click to collapse
Hi I have the same issue on my HTC Diamond. I flashed wm 6.5 and it was working fine, then it hanged on titanum weather. I reset and it stayed on the HTC Diamond page, I did hard reset and got the Olinex 1.40 3 color page. It does respond from serial to usb when I plug/unplug. Can I reflash without active sync?
Turns out I was able to flash, but both roms I tried work well on 1st install, but stay stuck on the Touch Diamond screen everytime I restart de device. Is it a problem with the radio not compatible , or is there a specific Hspl for each ROM???
I found solution for this problem. If your diamond won't boot go to bootloader mode and upgrade your radio http://modmydiamond.info/index.php?option=com_content&task=view&id=15&Itemid=26 and after that your dimond worked fine without loosing data.
try to hard reset the phone by pressing vol down key + the center button + reset button.
if the problem is still like dat..
try to install another rom..
davidwong007 said:
try to load back to default setting by pressing the power on button at the top of the phone, before the "Touch Diamond" logo come up, press and hold volume down button and the center button until the three color screen come out, then release the two button you are pressing..
if the problem still happen, that mean the rom you are using should have risk on it..
give it up and try other rom or flash it again..
hope my suggestion can help you solve the problem..
Click to expand...
Click to collapse
Thanks davidwong007 for your help, I was experiencing the same issue as op and your method did the trick. For a minute there I thought I had bricked my HTC Touch. I did step by step what you suggested and ended up in the rainbox screen, once I was able to do that, I knew there was a hope. i did a full factory reset of the phone and voila the phone fully booted, the pain in the butt touchflow loaded. Very important thing I forgot to do in the past is to back up my phone, after the restore you will lose everything on phone, except what is in the internal storage. Thanks again.