bootloader mode ?? - MDA III, XDA III, PDA2k, 9090 General

Hello! i would like to upgrade my xda 2s do wm2005 xpload and i have read wiki to! but really don't know how looks like bootloader mode! i pressed on/off, camera button and reset and nothing was happend, mda was reset and that is it! upgrade program do not see current software etc! can anyone can help me with that " by hand" please! first time is always hard! please! cheers Jocker01

Well, have you tried "Record"-button instead of "Camera"-button?
(Press and hold "Record", "Power", and "Reset" until bootloader comes up)

hello thx! finally i get bootloader mode, i've pressed camera, record, on/off and reset buttons! i hope so this is bootloader mode( THX Smokkky ). on screen i have dispelyed usb and v2.07. but ultility still dont update rom! cheers Jocker01

Related

please help me quickly

i have i-mate pda2k and i have installed wm5 on my device and i want to downgrade it to win2003se .
my problems :
1- the soft reset button are broken .
2. i haven't downgrade to win2003se.
please help me quickly
big boss, you may want to go back to you initial post and change the title to "How can I downgrade from WM5 to SE2003 without reset button" and you may get some help.
yup... just like Free888 said.
the alternative is to flash using a USB cable and NOT a cradle.
which makes the battery and the notch accessible.
you could release the notch to turn off, then lock it again + power button to turn on.

Revive URGENT PLEASE VERY URGENT

Hi all
I have a problem with my PDA (Qtek S200)
IPL 2.10.0001
SPL 2.G4.4PDA
GSM 02.69.21
THE 7.0.0.7
And it is this:
Made a backup of my contacts over SPBackup, did the flash ROM of everything he turned to run normally, I made the restores the contacts and SMS, ... and when it does reebot it is only by the initial image that presents the data above:
IPL, SPL, ...
We have tried to make the soft-reset (pen of the button and the small button on the camera and nothing)
My question: Does anyone know how solve this?
Best Regards and thanks
Bye
Anybody help me ?
Please it's very urgent...
thanks all
can you do a hard reset using the keys and see if that allows the device to boot again ?
reading your post again, i assume that is what you are trying to do with the camera button when resetting, hmmmm
Ok, if i were you, i would try this next.
Enter bootloader mode by doing the following
To enter bootloader, you need to hold the comm manager button and soft reset
If that allows you to enter bootloader, then try reflashing the rom
let us know how you get on after that.
also it might be worth posting in the forum for this device, if you havent already.
hard reset.....To perform a hard reset
Z3nD3n said:
Hi all
I have a problem with my PDA (Qtek S200)
IPL 2.10.0001
SPL 2.G4.4PDA
GSM 02.69.21
THE 7.0.0.7
And it is this:
Made a backup of my contacts over SPBackup, did the flash ROM of everything he turned to run normally, I made the restores the contacts and SMS, ... and when it does reebot it is only by the initial image that presents the data above:
IPL, SPL, ...
We have tried to make the soft-reset (pen of the button and the small button on the camera and nothing)
My question: Does anyone know how solve this?
Best Regards and thanks
Bye
Click to expand...
Click to collapse
To perform a hard reset
* Press and hold the CAMERA and COMM MANAGER buttons, and at the same time, use the stylus to press the RESET button at the bottom of your device.
Hello again ...
I am happy. Have back by my Qtek. had already done several times the Hard-Reset the PDA but always without success. I often followed and there began to anything on screen (the 3 colored bars, then asked the question of "send ..." where we have to press the green button "call") and then there came into bootloader and there could . He began to install everything right and it was if he had installed a Rom "new".
To all those who contributed to this "happy ending" my thank you very much.
sry my english
Bye and thanks

ROM Upgrade Please help

I have a HTC diamond and I replaced the rom with "DIAMIMG-WWEHD", the ROM upgrade was successful, but the phone did not start, Its starting and I am geting the Touch Diamond screen and then its restarts again.
I tired to restore with the vol down, center button and power button, Its shows restore...completed but when I boot I get the start screen and the phone restarts again.
Have I bricked by phone, is there a way to recovery.
Experts ...Please help
Did u Hard Spl your device before begining this process?
Step 1: Hard Reset your device (With the device turned on, press and hold the VOLUME DOWN and ENTER buttons "aka the center button" , then press the RESET button with the stylus tip).
I will discuss the next steps upon your response.
Let me know if this works.
band27 said:
Step 1: did u Hard Spl your device before begining this process? if yes to step 1 then move on.
Step 2: Hard Reset your device (With the device turned on, press and hold the VOLUME DOWN and ENTER buttons "aka the center button" , then press the RESET button with the stylus tip).
I will discuss the next steps upon your response.
Let me know if this works.
Click to expand...
Click to collapse
I tired the hard reset, I got a white screen with a message saying press volume up button to restore phone to manufacturers defaults, when I did that I got a message Restore...Completed Press VolUp to boot.
When I press the Volup button the phoen does not boot, it comes to the Touch Diamond screen and there is not ROM message at the bottom of the boot screen.
Ok, next step:
Go to your (Bootloader Screen): Vol. Down + Soft Reset
If you are successful here then just plug the device into you pc and get another ROM and start the process over by excuting the RUU_
Which Rom did u originally download.
K..let me know if this next step works.
band27 said:
Ok, next step:
Go to your (Bootloader Screen): Vol. Down + Soft Reset
If you are successful here then just plug the device into you pc and get another ROM and start the process over by excuting the RUU_
Which Rom did u originally download.
K..let me know if this next step works.
Click to expand...
Click to collapse
I pressed the vol down button and the reset button on the back, the phone boots and shows the boot up screen with the "TOUCH DIAMOND" banner and stays there for some time and restarts again
mukesh_thiru said:
I pressed the vol down button and the reset button on the back, the phone boots and shows the boot up screen with the "TOUCH DIAMOND" banner and stays there for some time and restarts again
Click to expand...
Click to collapse
Yeh, that is not your Bootloader Screen. Here, do it like this. Soft reset with stylus first....quickly let go of that and press Vol. Down in that order. When u see the Bootloader Screen you can let go of the Vol. Down button.
mukesh_thiru said:
I pressed the vol down button and the reset button on the back, the phone boots and shows the boot up screen with the "TOUCH DIAMOND" banner and stays there for some time and restarts again
Click to expand...
Click to collapse
The phone is booting again and again, only if I remove the battery it can be stopped.
So it won't let you go to the Bootloader Screen then? Hmm...?
So you soft reset it and pressed vol down and it just reboots constantly?
I put the phone in triggered bootloader mode. Thanks a lots guys for your qucik response.
For future refernce, this link can be checked for this kind of issue:
http://forum.ppcgeeks.com/showthread.php?p=650429#post650429
mukesh_thiru said:
I have a HTC diamond and I replaced the rom with "DIAMIMG-WWEHD", the ROM upgrade was successful, but the phone did not start, Its starting and I am geting the Touch Diamond screen and then its restarts again.
I tired to restore with the vol down, center button and power button, Its shows restore...completed but when I boot I get the start screen and the phone restarts again.
Have I bricked by phone, is there a way to recovery.
Experts ...Please help
Click to expand...
Click to collapse
dI have a HTC diamond and I replaced the rom with "DIAMIMG-WWEHD", the ROM upgrade was successful, but the phone did not start, Its starting and I am geting the Touch Diamond screen and then its restarts again.
I tired to restore with the vol down, center button and power button, Its shows restore...completed but when I boot I get the start screen and the phone restarts again.
Have I bricked by phone, is there a way to recovery.
Mukesh i have one solution for that download hspl package from here http://ds8.fileflyer.com/d/e3858be1...c/u56S/js0hkAj/diamond-hspl-1.23-and-1.24.zip extrace in other folder in ur pc than just connect ur phone to ur pc via cable and just click on dimond-sspl ms-dos batch file than follow the steps ur phone will connect via cable than follow this step 1. download unsigned hard spl v .1.93 olinex from here http://ficca.bounceme.net/download/HARDSpl_Diamond_OliNex_1.93_Unsigned.zip extract in other folders than connect ur phene via active sync than run Ruu if u got 100% job done try it tell me by post message what about ur prob good bless u
mukesh_thiru said:
I put the phone in triggered bootloader mode. Thanks a lots guys for your qucik response.
For future refernce, this link can be checked for this kind of issue:
http://forum.ppcgeeks.com/showthread.php?p=650429#post650429
Click to expand...
Click to collapse
Wow, you're problem would have been solved on the very first post if you told us your phone was CDMA.
mukesh_thiru said:
I put the phone in triggered bootloader mode. Thanks a lots guys for your qucik response.
For future refernce, this link can be checked for this kind of issue:
http://forum.ppcgeeks.com/showthread.php?p=650429#post650429
Click to expand...
Click to collapse
Wow, you're problem would have been solved on the very first thread if you told us your phone was CDMA. But you didn't think there was a difference probably because you didn't read much beforehand.

Can't load Bootloader (it just restarts)

hello to everybody, i'm new here
i just wanted to unlock my universal. i read the instructions in the readme of the downloaded file from here (Source) carefully and wanted to enter the bootloader.
but after i press the power, light and reset button simultaneously like here: Image ...it just restarts (like i only press the reset key).... --> no bootloader apers
anybody knows the reason why it doesn't start the bootloader? thank u for helping
hi, welcome to forum. sometimes can be tricky. but if you hold the buttons then press reset and continue holding for a couple more seconds then it should load the bootloader. hope this helps
thank u for ur quick answer!
i'm holding power and light button simultaneously and then i push the reset button. it seems to be not working.. like it ignors that i'm pressing the other buttons...?
hi, tried with mine. if i hold the light and power and when i press reset and hold it also it enters bootloader. if this doesnt work sorry maybe a more experienced user can enlighten us.
solved the prob
power is working. reset is working. if you press the light and backlight settings come up then thats working depending on your rom. not sure what your issue is if they all work.
ok solved the problem with a trick. now everything is working. thank you for ur help!

Bootlooader problem, cannot enter bootloader

HI!
First of all... great forum.
Than.. I''ve got an Arte (SPV M650 from PL orange).
I've flashed it few times, trying to find ROM most fitting my needs.
So please don't answer if U want to teach me how to perform a SR, HR, BL enter. I really know that, i did it few times already
Problem is, that for some time, i can't get into bootloader. I want to flash my Arte again, now with Shady's ROM, but... i can't get into bootloader.
If anybody have a REASONABLE idea for help i would be grateful.
THX I A
sorry for my eng...
Same problem here
Same problem, when i wan t to go in bootloader is showing me a White screen.
Solved in this way: Hope is helpfull
I have a microsd card of 128Mb.
I put there a image of a rom, and rename it just like in sdcard flashing way "ARTEIMG.nbh". The i press it the tow side buttons ( off and voice ) and with slytus i reset keeping after reset the 2 buttons pressed. is comming in the bootloader mode, but is not flashing the image i put it in card. SO after that I install what rom i want.
This is my ay to escape from white screen and entering in bootloader mode.
I have also a big problem
my htc P3300 is blocking at boot menu( white screen ..htc..ipl 1.12.0001 SPL 1.12.0000 GSM 02.67.90 OS 1.12.0.0) i can not succed to make anything. so if you can help me it wil be great.. i also speak romanian so maybe it will be easyer to tell me everything in romanian. thanks alot.
Hi @all, try holding the power and record button and pushing the reset button. than you get into the bootloader. (hold power and record after resetting, too)
now you can practice sd card flashing.
i hope i can help you...
mike
where is the reset button? pls
kingoldstyle said:
Same problem, when i wan t to go in bootloader is showing me a White screen.
Solved in this way: Hope is helpfull
I have a microsd card of 128Mb.
I put there a image of a rom, and rename it just like in sdcard flashing way "ARTEIMG.nbh". The i press it the tow side buttons ( off and voice ) and with slytus i reset keeping after reset the 2 buttons pressed. is comming in the bootloader mode, but is not flashing the image i put it in card. SO after that I install what rom i want.
This is my ay to escape from white screen and entering in bootloader mode.
Click to expand...
Click to collapse
but...i do this and when i on my PDA , report "Invalid Certificate" ... pls help

Categories

Resources