Lost all usb - 8525, TyTN, MDA Vario II, JasJam ROM Development

Running Schap's 4.01
It was syncing perfectly and for some reason it wont do anything via usb other than charge!
There is no connection notification from windows when I plug the unit in, in hard reset mode the coloured RGBW screen says serial not usb as other times.
It syncs fine via bluetooth.
I've unticked "advanced" in usb sync options and still nothing.
Any ideas?
A windows driver maybe?

eat this:
http://www.thbi.de/de/downloads/killassetupde.zip

Peer guardian blocks all USB connections
Are you running Peer Guardian on your comp by chance?? If so, it blocks the phone from syncing via USB but bluetooth still works. If you are running PG2 jsut run Task Manager and close it then connect

No I'm not running peer guardian.
I am running vista though. Thanks for the replys guys, appreciate it.
Anyone else?

sounds like a driver problem then. Go to Device Manager and When you connect your Hermes see what appears and delete the driver for it, then disconnect then reconnnect and itll install a driver for it, then check for updates with windows update and there should be an updated driver for it..download and install it, reboot and try again.
I'm running Vista and had to do that a couple of times when I had the same problem you are.

make sure also that you have usb connection enabled in in device settings in windows mobile device center.

Well bugger me it was the cable!
It was a car usbcharge cable and guee what....... it had no tx-rx connections!

Related

Activesync problems following hard reset !

Hi All
Hope someone can help - have tried looking through forums but can't find anything that solves this.
I was struggling with memory - down to 1mb of storage - so I did a hard reset. Memory problems solved and am minimising software I put on the phone now (and installing them to storage card etc).
However, when I try and connect it to my PC with activesync - NOTHING.
The phone starts to charge which implies to me that the cable works. I've also tried a different cable, and different USB holes on my PC. However, no luck.
The USB option is ticked in Activesync connection settings and still nothing.
Can anyone think what might be the problem - I have tried de-installing Activesync and re-installing, have deleted any partnerships, but dont know if i need to delete USB settings or something.
Hope you can help this novice overcome this problem,
Ta
That's the stupid Artemis default setting that causes that error. Go to Settings > Connections > USB-PC and disable the enhanced network option.
Thanks for the quick response but afraid it's not that problem - I already have it unchecked.
Any other ideas?
Which Version of ActiveSync do you use, which OS and which Firewall? Are you sure you did a hard reset - did it erase all your data and come up with the setup screen?
Started with 4.5, then downgraded to 4.2, but when it didn't affect the connection, I put 4.5 back on.
OS: Win XP
Firewall: Windows - but do 'allow exceptions'
Yes - did the hard reset which took me back to start up
Had the same problem, in my case Windows Media Player prevented Active Sync from connecting. What I did, launched task manager sorted processes by name, and then plugged in the artemis.
In my case after 5 seconds or so a Windows Media Player process started, I had to manually end this. Windows Media Player keeps trying to connect, but after the fifth time of stopping the service my phone finally was recognized!
My OS is Windows Vista, but I read other forums where people have XP with this problem. Good luck!
I don't seem to have windows media player running.
I asked someone at work today as my phone won't connect to my work pc either.
We realised I don't have the original mini usb cable that came with the orbit and the cable I am currently using seems a little loose.
I do have the headphones, and when I look at them, they have a really snug fit into the socket in the phone and has small gold strips on the inside of both parts of the mini usb rather than traditional cables which have them only on 1 side.
Perhaps this is the problem - do other people have a mini usb which has a firm connnection in the phone? Perhaps I need a new cable given that this is an issue with any pc I try and connect to?
Had also problems, had to totally disable the firewall and shut down the popupblocker and sometimes a reboot with saved settings, on w2k and xp with activesync 4.5.

Active Sync Problems with Tmobile TP2

I have ActiveSync 4.5 on my laptop and set my TP2 up to Sync with my work's Exchange Server OTA and it's working fine. I then went to setup AS (USB) on my laptop so I could drag files over but it won't connect. It just keeps trying to connect then just stops and I get an error on my PC saying it couldn't connect to the device.
Anyone else have this problem or know how you might fix it? I looked at the other AS threads and didn't see anything that worked for me. I have killed AS and Soft Reset my phone but to no avail. The computer recognizes that the TP2 is plugged in but won't connect. The Allow USB connection is checked on the phone's AS too.
Thanks,
Had the same problem and deleted MS active sync then reinstalled it and it worked now if I can only figure out how to change the soft keys I'll be happy
Well I uninstalled and reinstalled but to no avail. Does / did your TP2 automaticlaly make a network connection when you connected it via USB?
Lance
When you connect your phone, just choose the File Transfer mode! It's faster and doesn't use ActiveSync. You should be asked that when you connect USB.
I think something is up with the laptop as I connect my phone now and it doesn't even charge. I'm going to remove active sync again, and then reboot and see if that fixes anything.
I'll look for the file transfer mode. My 16GB MicroSDHC doesn't come until today (if I'm lucky) so i'm still ahead of the curve on most of this.
Thanks,
Lance
Robertsonland said:
I think something is up with the laptop as I connect my phone now and it doesn't even charge. I'm going to remove active sync again, and then reboot and see if that fixes anything.
I'll look for the file transfer mode. My 16GB MicroSDHC doesn't come until today (if I'm lucky) so i'm still ahead of the curve on most of this.
Thanks,
Lance
Click to expand...
Click to collapse
Try a new USB cable. My USB cable broke on me a few days ago. Or try a new USB port, or a new computer. It should be charging. That means that your USB connection is bad, not ActiveSync.
Go to your Device Manager on your computer.
Look in Mobile Devices.
Find your phone
Right click on it.
Uninstall the driver.
Unplug the USB cord.
THen plug it back in.
It will go thru the installing process again.
I know this b/c I have done it too many times. hth.
Simple fix
Goto the start menu>Setting then to the Connections tab at the bottom.
Select USB to PC
UNCHECK Enable faster data synchronization.
ActiveSync should work with your PC again.
johnreden said:
Goto the start menu>Setting then to the Connections tab at the bottom.
Select USB to PC
UNCHECK Enable faster data synchronization.
ActiveSync should work with your PC again.
Click to expand...
Click to collapse
I'm going to try this with the issues I've been having, seems like it might work.
Activesync has been randomly losing connection to the phone and sometimes the phone will stop charging. I've tried 2 different usb cables including 1 I've used for a long time with no similar issue.
Once, I've even been connected to Activesync and seen the phone stop charging. This phone seems to be similar to the MDA in that the hardware has to go through the operating system to charge the battery. Ugh, once my MDA battery was so dead that I couldn't start the OS and thus couldn't charge the battery, that was fun manually connecting wires to the battery terminals to get enough charge that I could start the OS.
cabranscom said:
Go to your Device Manager on your computer.
Look in Mobile Devices.
Find your phone
Right click on it.
Uninstall the driver.
Unplug the USB cord.
THen plug it back in.
It will go thru the installing process again.
I know this b/c I have done it too many times. hth.
Click to expand...
Click to collapse
Yup agreed, that works, I have the similar issue my ActiveSync sometime disconnected itself. Performed the above steps, then it never happened again.
I can't find "Mobile Devices" in Device Manager on XP. Is that tip just for Vista?
Also I have unticked the "Enable Faster Data Synchronisation" but still I can charge but not get a USB data connection.
Any other tips!

USB connection not working.

My TP2 (vodafone) has decided it doesn't want to connect via USB any more. I have tried different USB leads, and verified it's not that by using other devices. I've tried different USB ports on my desktop (Windows 7 RC 7100) and also tried my laptop (XP) neither of which want to connect.
I've checked the USB to PC section in settings and tried it as both Activesync and disk drive, and with and without the 'enable faster data synchronization' box ticked, and soft reset after changing each setting. but every time the computer just won't recognise that I have plugged a USB device in.
Any suggestions?
No one have any ideas on this? I've tried a hard reset now in desperation, and it still doesn't seem to work.
PC does not recognize TP2 connection
Same problem for me; the TP2 is not recognized by the PC (or laptop)
Is there no program to check this? Otherwise.......I have to send for warranty repair.
Anybody any idea??
I have the same problem.
I can't get the device to connect to my PC by USB. It charges through the PC USB lead though.
What did you end up doing? Is it time to make a warranty claim?
I'm not sure if it applies to your situation, but for the longest time I could not get my Kaiser to sync with my laptop (which I usually kept wifi off on).
Turns out ActiveSync was out of date and didn't work since I had upgraded to WM6.1. If you're up to date already that probably doesn't help, but I thought I'd toss it out there.
just to let you know, i returned my tp2 to vodafone and the replaced it. the new one worked fine as soon as i plugged it in to the usb. so that proved it had to be a hardware fault.

Windows Mobile Remote Adapter cannot start, error code 10

First I have to state: I've already searched the web and xda-developers forums. Tried all solutions found, none work.
I don't connect my HTC Touch Pro 2 to my computer (Vista 32bit) often; other than the first few days, when I was downloading a lot of softwares to my device, I don't connect them at all. But the point is I was able to connect to WMDC.
Yesterday I wanted to try out Pocket Diablo, so I had to connect my device in order to install .NET CF 2.0. But I found I can no longer sync:
- Before I connect the device, I can see WMDC's green tray icon
- After I plug in the device (using the cable from HTC), WMDC's tray icon disappeared.
- I checked Device Manager, and found "Windows Mobile Remote Adapter" cannot start, error code 10. There was no mobile device listed.
- I tried another USB port, same result. I tried uninstalling all USB hubs and root hubs, let them reinstall, reconnect device, same result.
- With device still plugged in, I uninstalled "Windows Mobile Remote Adapter" and deleted the driver too. Then I unplugged device, uninstall WMDC driver update and WMDC itself, reboot PC, download WMDC6.1 from Microsoft again, reinstall WMDC, reboot, still no tray icon, and reconnect device with same result.
- I tried the above together with giving Users group full control on the registry key "HKLM\Software\Microsoft\Windows NT\Current Version\Svchost\WindowsMobile", same result.
- If I uncheck "advanced connection" on my device, there is no "Windows Mobile Remote Adapter" in device manager, but there is a generic mobile device listed. In WMDC it still thinks there is no device connected, and I cannot access the device in Windows Explorer.
- If I connect the device as a disk (under device's USB connection settings), I can access the device through Windows Explorer.
- I even hard-reset my device, still same result.
- I tested my old O2mini, same result.
- I don't recall any big changes on my system since my last successful connection.
- I tested my HTC Touch Pro 2 in my office (Vista 32bit), and it can be connected successfully.
So it seems the problem is in my home computer; the Windows Mobile Remote Adapter (version matches WMDC6.1's version) refuses to work in all cases.
Other than taking the sync cable in my office back home tomorrow, I'm all out of ideas of what to try next.
Can anyone give me a helping hand?
Bump. Please help, I really need to solve this.
- I'm taking the cable in office home, but I highly doubt that is the reason because with the cable at home I can connect as a disk and can charge.
- I notice in office (the successful case), the remote adapter is named "Windows Mobile Remote Adapter #2". At home (the failure case) there is no #number, just "Windows Mobile Remote Adapter".
Tested and it is not the cable. Cable used to successfully sync in office has same effect at home - Windows Mobile Remote Adapter cannot start, code 10.
I tried enabling WMDC debug log, but there're none - looks like the process failed at the driver stage and WMDC is not even started.
Also, when I have the device connected with the non-functioning driver, it seems to wreck havoc on my real network driver. I often need to reconnect my network connection.
Can anyone help?
It's getting weirder and weirder...
- I reinstalled WMDC for the countless time, and suddenly I am able to connect to O2mini (which does not connect via a network adapter). O2mini shows up in WMDC (can setup a partnership) and explorer. But not HTC TP2.
- If I disable advanced connection on TP2, I can connect TP2 as a Mobile device, but there is no network adapter. WMDC detects no connection, and I cannot view TP2 in explorer.
- I tried connecting O2mini again after TP2's failure, and O2mini cannot connect too - device manager shows no problem, but in WMDC I get nothing but the red stop sign and a simple message: "Error". No entries in event viewer.
And is anyone even reading this thread?
I was having a similar deal. Sync works solid on XP at home, was working but then stopped on 2 laptops with Vista and giving me those error codes.
I did the same things as unistalling mobile center on vista to no avail.
What did work was going onto the device, Start/All Applications/ActiveSync. Then Menu/Options and delete on the laptop PC's.
Now when I sync my vista laptop to the device it shows up as an additional device. I can copy files to it, I'm not sure if it syncs any other info.
The active sync also has an option for connections where you can uncheck "same for all pc's". I didn't try that one, but it might do something.
Update the Driver?
shealine said:
I was having a similar deal. Sync works solid on XP at home, was working but then stopped on 2 laptops with Vista and giving me those error codes.
I did the same things as unistalling mobile center on vista to no avail.
What did work was going onto the device, Start/All Applications/ActiveSync. Then Menu/Options and delete on the laptop PC's.
Click to expand...
Click to collapse
You mean removing the partnerships? I already did that - I had hardreset my TP2 for nothing too.
yrreP said:
Update the Driver?
Click to expand...
Click to collapse
I tried, but Vista said I already have the latest version (6.1.6965.0). I tried uninstalling (and fill the checkbox to remove the driver) and reinstalling, no difference.
It has to be something not right on my computer's drivers.
I'm going to compare the driver files of my home and office computers and see if there are any difference...
I copied all files related to the Windows Mobile Remote Adapter home, and compared them to mine. They are all identical.
I also tried forcing Device Manager to show non-present devices (by setting two environment variables), removed the related ones and tried again. Same result.
I'm all out of ideas now.
I'm even considering moving up to Windows 7 (Ultimate 64-bit), hoping that will solve my problems.
-- but what? They leave me with a nasty bug and I consider paying them even more? Whiskey, tango, foxtrot?
Awesome, finally i found someone that has (i think) 100% my problem.
Let me ask you this, what is your computer specs? Because this happened to me after i got a new computer >.< .
Mine is
Asus p7p55d LE motherboard
i5 50?
Crucial Ballistix 2GB (2 x 1GB) 240-Pin DDR3 SDRAM DDR3 1333 (PC3 10600)
I also have a HTC Touch pro2 (verizon) but i have testing my computer with a Samsung Omnia (verizon) to confirm my problem.
Edit: BTW this is on a Windows 7, just throwing it out there so that people can be even more mind boggled
Asus P7P55D Deluxe
Intel i7-860
2 sticks of Kingston 2Gb
I got my TP2 from Fortress (Hong Kong), they added a bunch of goodies in the ROM, like the radio cab, 1% battery driver, a business card scanner, etc.
You have the same problem on Windows 7? I am going to buy W7 tomorrow, I'm going 64-bit...
If I get the same problem in W7, then well, damn... at least I can connect TP2 as a driver and write data to it. But if I need to install anything from the PC-side, I'll need to rip the cab out of the installer.
holy crap then i think i know why its not working. Maybe its because of the new chipset p55? Doesnt support the drivers? or something
bornskilled200 said:
holy crap then i think i know why its not working. Maybe its because of the new chipset p55? Doesnt support the drivers? or something
Click to expand...
Click to collapse
Definitely not.
Plus I have sync'ed successfully before, and my TP2 plus cable can still sync in office, advanced connection on. It's a software problem.
I encountered the exact same error in Windows 7.
The Windows 7 is a fresh install, Windows updated, and installed 64-bit version of WMDC.
Darn.
First, sorry for my very bad english.
I had the same problem ( Error code 10 with Microsoft Mobile Remote Adapter) with p7p55d and Windows7.
It was a trouble with my asus p7p55d.
- I updated my bios to the 0711 version (this version does not appear on AsusUpdate, i found it on www.asus.com)
- I uninstall old Windows Mobile remote adapter
- I uninstall WMDC
- reboot
- simply plug my phone and let windows update do the job. This time it was good for me...
I have the same issue with ASUS P7P55D PRO and Windows 7 Ultimate 64bit, even with BIOS 0711. I tried all the ideas, nothing helps.
The same problem for me.
Windows 7 64bit,
Gigabyte P55M-UD2 Mainboard
I report great success with this problem!
Like suggested from a previous poster, i did update my bios to 605 (this is for p7p55d LE). But i noticed one thing, the setting for Plug and Play was set to that the bios handled it. I changed to so the that OS (?) handled it instead and tried everything again.
Happy to say (after some extra problems that does not pertain to this error) i finally got it to work. Hope my experience help others.
Encountered a similar issue yesterday.
WMDC could not sync. Although when selected as a disk drive, it connects fine.
What fixed it for me was to disable this setting in the device: Settings/connections/usb to pc/enable faster data synchronization.
Exit out, no reset required.
Good luck.
I have the same problem since my new gigabyte p55-ud5
i have windows 7 Ultimate. my htc diamond work fine for one week, then it stoped sync.
i think its somthing with the memory....
i tried to change the speed on my corsair DHX 2GB from 1600Mhz to 1333 and it worked for couple of days.
then it stoped sync.
tried to add voltage in bios but no good.
updated the bios - then it only worked with memory speed 1333 or 1066.
i shutdown my computer only once in a week.
then it started again. now no matter what i do - no SYNC.
i searched for this error alot and the common hardware is:
P55 + vista/win7 + HTC.
PLEASE HELP!!!!!!!!!!!!!!!!!!!!!!!!
Firm-up!
i have a good news!
Finally i got it after firm-up the bios.
Asus p7p55d turned out to got a problem installing 'Windows ... Adapter'
http://www.asus.com/product.aspx?P_ID=RBA8CzWoopUlYRFZ&templete=2
.
Description P7P55D 1002 BIOS
1. Fix PCI-E X16 may downgrade to X1 mode
2. Improve system stability
Good Luck!

computer problem!

i'm not sure if this is the right section to ask this but my tilt 2 is not recognized by my computer anymore. I thought maybe it is the phone but it's recognized on other computers so I was wondering is there a way to reinstall the driver on my computer or some other fix someone know of?
I think I saw some threads with similar problems but I didn't see any definitive answer in any.
HELP PLEASE!!!!!!!!!!!!
stevenmc8602 said:
i'm not sure if this is the right section to ask this but my tilt 2 is not recognized by my computer anymore. I thought maybe it is the phone but it's recognized on other computers so I was wondering is there a way to reinstall the driver on my computer or some other fix someone know of?
I think I saw some threads with similar problems but I didn't see any definitive answer in any.
HELP PLEASE!!!!!!!!!!!!
Click to expand...
Click to collapse
Do you have XP or Vista/7? The first step you should try is uninstalling/reinstalling whichevery type of sync software you have on the PC...for XP it's ActiveSync, for Vista/7, it's Mobile Device Center. A fresh reinstall of those sometimes clears this problem up, and it's the easiest solution to try first
I have xp and I have uninstalled and reinstalled but that doesn't do anything my phone still isn't recognize that's why I was wondering if after u uninstall does the driver remains on the hard drive and if so how would u remove the driver so u can reinstall it.
Do you use the same cable when you are connecting it to the other computers? If you do then... well I dont know.. I would still try a new cable and wiggle it a bit
When you uninstall the Active Sync I believe it does take the driver off as well...
When you connect your phone to the computer does it still come up asking if you want to connect via Active Sync, Disk Drive, Internet Sharing?
I'll give you one method that helped me at least when I was having connection issues, have no idea if it is related to yours (and it might not even be applicable to the older XP version of ActiveSync).
While your phone is connected, go into Device Manager and under the Network adapters node, look for "Microsoft Windows Mobile Remote Adapter". If it is there, uninstall it.
After that, disconnect then reconnect your phone.
As a long shot, you would not happen to be running any VPN software would you? A connected VPN always makes syncing the phone impossible.
Is your phone charging while connected?
I had/have a USB connection issue with my Tilt2. It wasn't recognized by the computer, but it was charging. When I connect through bluetooth, it is detected just fine. I am assuming that my issue are the pins in the USB connector on the phone, since I have the same issue with different cables.
Aaron McCarthy said:
When you connect your phone to the computer does it still come up asking if you want to connect via Active Sync, Disk Drive, Internet Sharing?
Click to expand...
Click to collapse
No the only thing it does now is charge.
MooGoo said:
I'll give you one method that helped me at least when I was having connection issues, have no idea if it is related to yours (and it might not even be applicable to the older XP version of ActiveSync).
While your phone is connected, go into Device Manager and under the Network adapters node, look for "Microsoft Windows Mobile Remote Adapter". If it is there, uninstall it.
After that, disconnect then reconnect your phone.
As a long shot, you would not happen to be running any VPN software would you? A connected VPN always makes syncing the phone impossible.
Click to expand...
Click to collapse
I will try what u suggested. no i don't have any vpn software installed on my computer anymore.
jcterry said:
Is your phone charging while connected?
I had/have a USB connection issue with my Tilt2. It wasn't recognized by the computer, but it was charging. When I connect through bluetooth, it is detected just fine. I am assuming that my issue are the pins in the USB connector on the phone, since I have the same issue with different cables.
Click to expand...
Click to collapse
yeah it's still charging but that is it... nothing else happens
Every so often when I connect my phone to my pc all it does is charge.. All I do to fix it is soft reset the phone AND restart the computer. Usually after that it works fine. If not just take it off and put it back on the dock or cable.. if you try a different cable that might work for you too. Or try plugging your cable into a different usb port on the computer

Categories

Resources