Related
I do a lot of texting , and the tiny little keyboard just aint as easy to use with my fingers with one hand.
My Artemis didnt have a Keypad , or T-9 input keypad, only had the keyboard, block recognizer, transcriber, & letter recognizer.
My old S200/Jamin had the Keypad dialer , made texting so much easier.
Anyone know where I can located a cab file for T-9 input??
Thanks in advance
Just copy over the cab file in your my documents folder and Launch, you should reboot the Artemis.
This one is international, so with different languages on board.
Greetings
Anyone who have the Norwegian langugae for T9 with PhonePad?
smilys said:
Anyone who have the Norwegian langugae for T9 with PhonePad?
Click to expand...
Click to collapse
Hei! Hvis det er det samme som på S100 kan jeg skaffe det, har en liggende å slenge...
In english: If it is the same dll file that was uesed in the Qtek S100 PhonePad, then I can provide it?
mvh
PK
Kjempeflott om jeg få teste om det fungerer på P3300.
Great
OK!
Norwegian DLL ripped from S100...
PK
Anyone who can help me to get the norwegian file into the program?
Hi Guy,
I have downloaded the file .ab and followed the instructions, but I do not find nobody icon in the device. someone can help me? thanks
German language does not work. I can select it, but when writing SMS it recognizes/proposes only English words. Any solution for this?
regards
Zonk76
Try a soft reset after choosing GERMAN language.
After that, my Phonepad writes T9 in german.
paalkr said:
OK!
Norwegian DLL rippet form S100...
PK
Click to expand...
Click to collapse
Where do I copy this dll ?? I dont have any map called dictionary.
My P3300 doesnt have transcriber, I only have keyboard. And now I've got phone pad.
How do I install transcriber??
Phone Pad WWE version
I have altered the cab and removed all the languages except for english leading to a smaller install - saving you 0.6 Mb
Does anyone else find that the Phonepad locks up sometimes (possibly due to lack of memory), leading to the inability to change SIPs, and the necessity to perform a soft-reset?
CJBS said:
Does anyone else find that the Phonepad locks up sometimes (possibly due to lack of memory), leading to the inability to change SIPs, and the necessity to perform a soft-reset?
Click to expand...
Click to collapse
Not on my wizard or artemis - what device are you referring to?
meschle said:
Not on my wizard or artemis - what device are you referring to?
Click to expand...
Click to collapse
I'm referring to my Blue Angel, but it's the Phonepad taken from the O2 Mini (it may not be the version that's been included with this post if it's a newer one for a WM5 device...).
I'm wondering how memory works for SIP input anyway, because sometimes when I have heaps of free memory, and I use PenPower, it won't change to another SIP (eg. Null Keyboard, which doens't use much memory). Is SIP memory specially allocated?
CJBS said:
I'm referring to my Blue Angel, but it's the Phonepad taken from the O2 Mini (it may not be the version that's been included with this post if it's a newer one for a WM5 device...).
I'm wondering how memory works for SIP input anyway, because sometimes when I have heaps of free memory, and I use PenPower, it won't change to another SIP (eg. Null Keyboard, which doens't use much memory). Is SIP memory specially allocated?
Click to expand...
Click to collapse
The version posted is 1.0 (Build 22364)
Maybe its your null keyboard thats causing the problems - i recall when i used it - it was a bit glitchy.
It's definitely not the Null Keyboard, which I've never had a problem with, as the problems occurred even before I installed the Null Keyboard.
The version I'm referring to is also 1.0, but build 18526. (I don't know why they don't increase the version number like every other software vendor).
I'll try the version posted, and see whether I continue to experience problems (that is if it works on PPC2003....)
Works on PPC 2003SE
Well.... so far so good. At least it works on PPC2003SE - many things these days seem only to work on WM5! Thanks for making this available.
Wrote too soon! It's already locked up on me. Managed to lock the whole device this time, though, rather than just the SIP. I had to do a soft reset. (I'm wondering whether it's a combination of using PenPower and the PhonePad together).
Anyone know where in the Windows Mobile 5 filestructure T9NorwegianLdb.dll resides?
The Phone Pad - International.CAB.zip seem to work fine on the HTC P-3300.
Just point and hold on the small up arrow on the right side of the keyboard icon when you write an SMS to choose it.
Norwegian is not included in the file posted in this thread however.
I guess we need to install the T9NorwegianLdb.dll for that. Anyone know where to copy it? I am unable to find the phone pad directory in WM5.
tomtom 6 working?
other apps problems?
thanks
fabri
Hi,
I've flash my trinity with last LVSW rom, all my applications till working on WM6....
No problem ;-)
thanks, any other test tomtom 6?
thanks, any other test tomtom 6?
TTN6 works perfectly on the Mun_rus ROM (and gets a fix from cold in under 2 minutes). Not tried the LVSW
NeilM said:
TTN6 works perfectly on the Mun_rus ROM (and gets a fix from cold in under 2 minutes). Not tried the LVSW
Click to expand...
Click to collapse
TOMTOM6 works perfect with LVSW Rom, GPS lock in 2 mins from cold start
could you please post your working tomtom 6 settings? I am having issues getting tomtom to find a GPS device!
Is the GPS port still com port 9? Is the baud rate still the same? Do we need to turn 'let windows manage my GPS settings off?
Have tried various combinations and still no luck
Thanks in advance,
WWWeed
hmmm, If I cant resolve this I going to have to downgrade back to WM5!
This is really annoying when I know other people HAVE it working..
Ahh well back to the shipped orange rom...........
In TomTom select "Built-in GPS receiver" it won't even ask you for a com port or baud rate.
This is only available in TomTom 6.03. If you have version 6.00 you need to select Other NMEA GPS receiver com port 9 and baud rate 4800 or 9600 (both worked for me)
Maybe: You must switch on phone part of mobile. When phone is off (Flight Mode) gps doesnt´ work.
Anyone have an upgrade for the p3600 to get WM6?
I've been searching the forum, but can't find what I'm looking for. Is it possible to upgrade the p3600 to a WM6 version?
Akselp3600 said:
I've been searching the forum, but can't find what I'm looking for. Is it possible to upgrade the p3600 to a WM6 version?
Click to expand...
Click to collapse
sure, read wiki http://wiki.xda-developers.com/
Akselp3600 said:
I've been searching the forum, but can't find what I'm looking for. Is it possible to upgrade the p3600 to a WM6 version?
Click to expand...
Click to collapse
dude, u totally out, forget wm6, u should flash a wm6.1 rom now.
try any one here, most of them are good.
sailer1983 said:
dude, u totally out, forget wm6, u should flash a wm6.1 rom now.
try any one here, most of them are good.
Click to expand...
Click to collapse
Just after I wrote the post I discovered the amazing wiki Found the AX3L wm6 rom. Works almost perfect. Do you know if there is anywhere to find a skin for the wm6 that works well?
Hi,
1. go to -> start->Settings->System->External GPS
2. Make sure the COMPORT changed from GPD1 to COM1.
3. Click O.k
Goto IGo for Example, and search GPS, or Manualy configure it for COM1 - 57600.
And VOILA!
Enjoy,
Nadavi
Nadavi said:
Hi,
1. go to -> start->Settings->System->External GPS
2. Change the Programs GPS from GPD1 to COM1.
3. Click O.k
Goto IGo for Example, and search GPS, or Manualy configure it for COM1.
And VOILA!
Enjoy,
Nadavi
Click to expand...
Click to collapse
no need portsplitter or GPSgate?
pdaman said:
no need portsplitter or GPSgate?
Click to expand...
Click to collapse
Nope
Nadavi
Nadavi said:
Nope
Nadavi
Click to expand...
Click to collapse
OK
You Have to Install GPS GATE.
Then you can make the modification stated in POST #1.
and you can exit GPS GATE.
Nadavi.
Nadavi said:
OK
You Have to Install GPS GATE.
Then you can make the modification stated in POST #1.
and you can exit GPS GATE.
Nadavi.
Click to expand...
Click to collapse
So after this...Gpsgate/portsplitter is no longer needed?
Thanks
pdaman said:
no need portsplitter or GPSgate?
Click to expand...
Click to collapse
Portsplitter is needed only for tomtom...
J273 said:
So after this...Gpsgate/portsplitter is no longer needed?
Thanks
Click to expand...
Click to collapse
You don't need to run it. (it runs a small EXE on startup). so you can not uninstall.
Nadavi said:
You don't need to run it. (it runs a small EXE on startup). so you can not uninstall.
Click to expand...
Click to collapse
Ok..Great thansks...Ill give it a try.
Do you think there will ever be a way of getting rid of gpsgate/portsplitter all together for tomtom use.
Thanks
instead of changing GPD1 to COM1 change to com8, no need for gpsgate/portsplitter at all! works after hard reset without any other programs, then at least iGO and Destinator works flawlessly.
sevet said:
instead of changing GPD1 to COM1 change to com8, no need for gpsgate/portsplitter at all! works after hard reset without any other programs, then at least iGO and Destinator works flawlessly.
Click to expand...
Click to collapse
Ahh thats good news....Is this the same with tomtom?
Thanks
Thank You all Guys
sevet said:
instead of changing GPD1 to COM1 change to com8, no need for gpsgate/portsplitter at all! works after hard reset without any other programs, then at least iGO and Destinator works flawlessly.
Click to expand...
Click to collapse
Do you mean set the GPS program port under programs to COM1 and then under hardware set it to COM8?
Thanks
You change the one which is default on GDP1 to COM8 its the program, leave hardware on COM9, then set all gps programs to COM8 or auto discover.
Like i said, only tested on igo and destinator, i believe it will work on tomtom
sevet said:
You change the one which is default on GDP1 to COM8 its the program, leave hardware on COM9, then set all gps programs to COM8 or auto discover.
Like i said, only tested on igo and destinator, i believe it will work on tomtom
Click to expand...
Click to collapse
Ok thanks....I have tried this but it dont seem to work for tomtom for me
Do you have tomtom at all you could try?...I wonder if its anything to do with the new radio i just flashed.
Does it work for google map using GPS satellites and not GPRS or Wap?
it works for copilot, the trick is to restart the device after you make the com port change before you configure gps software
yup it works also with google earth. you can see that it is acquiring satellites while browsing
thanks for this.
sorry nub....where i can find iGo in my i780?
Thanks
Hi all,
i want to know if i am alone to get the trouble. I use a cooked rom with the new htc keyboard. when i use IGO8 and try to find a city, it automatically add me letters "aa" in the city field, i don't push any touch on the pad.
so i can't enter any city.
to solve the problem i should first change the default keyboard in a sms a restart IGO and everything is ok.
just to tell you that i tried with QWERTY and AZERTY (I'm french) and it's the same
Have you got a solution ?
thank you
Add this to sys.txt:
Code:
[device]
Type="ALIAS_TOUCH HD"
sdcard_dsk_num=7
thank you very much it works i didn't have the type line in device in sys.txt now everything is ok
thank you
Thanks...
i had the same problem when i switched to new Dutty's ROM...
i was going crazy about it, for some time now, and tried to avoid using IGO...
it works like a charm once again...
And for the Diamond ? it's the same.
Thank you
Hello there,
Which version of iGO8 works for the Rhodium?
I've tried various releases and still had not been able to make it work!
Thanks in advance
Yuval lavie
Yuuvi said:
Hello there,
Which version of iGO8 works for the Rhodium?
I've tried various releases and still had not been able to make it work!
Thanks in advance
Yuval lavie
Click to expand...
Click to collapse
Look in many of the threads already here. In general, you can say that all the official PDA releases work. These are 8.3.2.64029, 87762 and 97313. (Maybe more). With these versions a very basic sys.txt (as supplied with these versions) will work, as long as you add:
[device]
sdcard_dsk_num=7
(It took me three days to find this out...)
andrehj said:
Look in many of the threads already here. In general, you can say that all the official PDA releases work. These are 8.3.2.64029, 87762 and 97313. (Maybe more). With these versions a very basic sys.txt (as supplied with these versions) will work, as long as you add:
[device]
sdcard_dsk_num=7
(It took me three days to find this out...)
Click to expand...
Click to collapse
I had problems getting mine to work also. All I did was a fresh install, nothing edited in sys.exe, but I replaced data.zip with a newer version and it seems to be working fine!
I am ruining 8.3.2.93122 and it runs just fine.
Just to confirm it runs ok with version 8.3.2.1972 on the TP2 with these settings in sys.txt
[interface]
show_exit=1
[rawdisplay]
screen_x=480
screen_y=800
class="portrait"
[device]
sdcard_dsk_num=7
[folders]
App="Storage card/iGo8"
Click to expand...
Click to collapse
andrehj said:
[device]
sdcard_dsk_num=7
Click to expand...
Click to collapse
In fact, what does it mean ?
I guess it's giving iGO the correct location of the sdcard i.e. disk number 7.
(I'm also guessing) The other 6 disks will be internal storage/ROM/backup ROM/etc.
ok, but it´s strange as App looks for "Storage card"
Code:
[folders]
App="[i]Storage card[/i]/iGo8"
... it´s just to understand ...
Whatever I install, I keep getting "Initialization error: no language files were found"
any help ?
do you have insert(copied) a Lang_YourLanguage.zip
you will find this on
-iGO
-CONTENT
-LANG
greetz
Aight, so I fixed all these problems and the program works great with all maps etc.
but it doesnt know how to determine where I am..
I'm telling it to take me to some place, and it creates a way like I'm in Jerusalem, while im not there xD...
IGO8 dont find my internal GPS???
Hi,
the programm and the maps work fine on my TP2 but he always shows me:
no GPSdriver found!
Igo dont find my internal GPS, any ideas???
thx
look in the settings
Port 4
Baudrate 57600
Change in the registry
HKLM\System\CurrentControlSet\
GPS IntermediateDriver\Drivers\GPSOneDevice\
PollInterval = 100
and delete these (GPSLogFile.txt+
GPSLogFileBack.txt) files you will find in the \Windows\ folder
take a softreset, then run QuickGPS or if you have time
without QuickGPS...
greetz
hm...ty for the tip...
but nothing change!
igo shows me after autoscan:"no gps driver found"
on Google Maps it works fine with the internal GPS
Schnalle said:
Hi,
the programm and the maps work fine on my TP2 but he always shows me:
no GPSdriver found!
Igo dont find my internal GPS, any ideas???
thx
Click to expand...
Click to collapse
Schnalla,
What regional settings are you using?
For me strangly enough I found that when my local are set to anyting other then English iGo doesn't find the GPS receiver.
So try changing local to English UK or the like (might need a restart).
Then go to iGo GPS settings and run the automatic scan for GPS device.
It worked for me.
Once the GPS receiver is found you can change the Regional settings back to whatever you had before.
IGO8 Problem
Dear all,
I've got a IGO8 problem too. I've got the same version as up here. (The last version with a working TTS)
When i've touch flo 3d turned off (and using the basic windows mobile start screen) is IGO8 working perfect.
After turning on the touch flo 3d is igo working for a short time, but after an hour, when I try to start the application ==> I will get a error. I will get this message 1/2 second after pressing the igo icon and before I can see the loading screen.
the error is: "Failed to reserve virtual address space"
Can anybody help me to let it working with touch flo 3d? Or can somebody explain what the problem is?
Thanks in advance!
Ranney
ranney said:
Dear all,
I've got a IGO8 problem too. I've got the same version as up here. (The last version with a working TTS)
When i've touch flo 3d turned off (and using the basic windows mobile start screen) is IGO8 working perfect.
After turning on the touch flo 3d is igo working for a short time, but after an hour, when I try to start the application ==> I will get a error. I will get this message 1/2 second after pressing the igo icon and before I can see the loading screen.
the error is: "Failed to reserve virtual address space"
Can anybody help me to let it working with touch flo 3d? Or can somebody explain what the problem is?
Thanks in advance!
Ranney
Click to expand...
Click to collapse
I've found some information here: http://forum.xda-developers.com/showthread.php?t=526679&highlight=igo8
But is there an another solution to get it working without resetting the device or disable the TF 3D?
It must have a (Simple?) reason becouse it will work after a reset but not anymore after some time...
Thanks in advance!
Ranney
i am using the same sd card from my tp1 (nothing changed). igo 8.3 is working perfectly.
ranney said:
Dear all,
I've got a IGO8 problem too. I've got the same version as up here. (The last version with a working TTS)
When i've touch flo 3d turned off (and using the basic windows mobile start screen) is IGO8 working perfect.
After turning on the touch flo 3d is igo working for a short time, but after an hour, when I try to start the application ==> I will get a error. I will get this message 1/2 second after pressing the igo icon and before I can see the loading screen.
the error is: "Failed to reserve virtual address space"
Can anybody help me to let it working with touch flo 3d? Or can somebody explain what the problem is?
Thanks in advance!
Ranney
Click to expand...
Click to collapse
hi ranney
with which version tts is working on your tp2?
greez
emanuel
emanuel-paul said:
hi ranney
with which version tts is working on your tp2?
greez
emanuel
Click to expand...
Click to collapse
Hi emanuel,
I've got version 8.3.2.93112. But also problems with TTS now. When I set the voice in IGO to a basic version (non TTS), close igo, reboot, start igo and set it to a TTS ==> it's working. but after shutting it down and restarting ==> TTS is not longer working. (And after a day, IGO cannot be started anymore and the device had to soft reset to let IGO run again...
Ranney