Hello everyone,
well i have differnt question/ issues with my O2 atom:
a) this atom has ROM version 20051123B2 & Radio version MN1XN_PDA_051122. can any one recommend me as to what rom version should i upgrade it with.
would upgrading the ROM harm it? I badly need to upgrade as its probably one of the most initial atom realeases and its too slow to work on.
B) the phone has no smart dial option/software. I tried to install a software intellidialpro but it doesnt work.
C) Doesnt work well if i use as external usb modem connecting it with my laptop. the browsing & incomming bytes tends to stop after initial 10 minute usage and i have to disconnect it and reconnect it all over again to be able to use internet (that too for max 10 minutes)
F1
I had to soft reset my orbit the otherday and since then have been unable to sync with my pc.
I have tried re installing activesync and soft resetting the orbit with no joy. when I select activesync on the orbit I get the message displayed in the attached jpeg.
I would rather not do a hard reset as some of the programs I use (particularly DrugDoses) use a device key for registration which is changed whenever the device is hard reset.
Any help and advice would be appreciated.
Forgot to add, I am using XP pro and my other WM6 device has no problems so the problem must be on the orbit.
ROM: 3.4.206.2 WWE
ROM Date: 8/31/07
Radio: 02.98.90
Protocol: 4.1.13.47
Same problem
I have the same problem since installing B&B 4.3 GER on my device. I should mention that I am using Vista.
Ideas, anybody?
I had the same problem when i was running B&B 4.3 whilst using xp. At first i thought it was a bad connection from the phone to the mini usb cable (as i manange to get connected whilst bending the wire). I managed to get a connection after 2 days of trying. I then reflashed the phone with a different ROM & all was well again. For some reason some people are affected by this whilst others arent. No idea why, but there is a conflict somewhere which was resolved once i changed to a different ROM. Hope this helps. But dont dispair cos you will eventually get a connection & then you can reflash.
On PPC, You could try looking at connections, USB connection and make sure advanced usb is disabled. May help.
Hello,
first of all, i want to thank you all for this great forum.
I have a small problem. I have bought a few days a HTC P3600. Everything was working fine.
Yesterday i tried to upgrade to wm6 using MARY 3.4.1 with sucess following the upgrade guide in trinityguides.info.
I have installed the Des’ Crash-Proof SPL and then flash the MARY 3.4.1 ROM.
Until now everything is working fine except the active sync. I tried to AS with the usb cable but it won't connect. It gives me the following error:
"Communication Error:Cannot start communications with the desktop computer. Remote Networking could not start due to a critical error (Error 608). Please reconnect your device. If the problem persists, restart your device using the instructions provided by the manufacturer."
I've googled it and tried all the suggestions that i could find, with no success.
If i connect via BT there is no problem.
The problem is that i want to put back the official ROM from HTC and if i can't connect with active sync via usb, i can't restore it.
BTW, if i put back the official ROM, the Hard-SPL is also flashed to the original??
Thank you
cabexas said:
Hello,
first of all, i want to thank you all for this great forum.
I have a small problem. I have bought a few days a HTC P3600. Everything was working fine.
Yesterday i tried to upgrade to wm6 using MARY 3.4.1 with sucess following the upgrade guide in trinityguides.info.
I have installed the Des’ Crash-Proof SPL and then flash the MARY 3.4.1 ROM.
Until now everything is working fine except the active sync. I tried to AS with the usb cable but it won't connect. It gives me the following error:
"Communication Error:Cannot start communications with the desktop computer. Remote Networking could not start due to a critical error (Error 608). Please reconnect your device. If the problem persists, restart your device using the instructions provided by the manufacturer."
I've googled it and tried all the suggestions that i could find, with no success.
If i connect via BT there is no problem.
The problem is that i want to put back the official ROM from HTC and if i can't connect with active sync via usb, i can't restore it.
BTW, if i put back the official ROM, the Hard-SPL is also flashed to the original??
Thank you
Click to expand...
Click to collapse
Try an other usb port on your computer.
And yes, offical rom restore everything (ipl,spl,radio,os)
I have already tried that.
The only thing that i can remember that i didn't tried, is connect in a different computer, but i will try that as soon as i get home.
thanks
try another ROM. got that activesync issue also with every Mary ROM.
You can find it in UDK rom thread
Active Sync Error 608
Try this to solve the problem:
Quote:
Originally Posted by nanni100
I solved cause my Windows Firewall was damaged and not customizable, then i found a reg file to solve this problem, installed on pc and reboot. On startup i saw the window of Win Firewall who asked me to unlock Activesync i said yes and turn off the firewall
I have a ethernet router with DHCP enabled
Then i configured the phone:
-Enabled Advanced Netword Function
-Go on Setup, Wi-Fi, Network, Remote HOST- NDIS
-Select the Specific IP Address like this:
IP Add: 169.254.2.1
Sub Mask: 255.255.0.0
Gateway: 169.254.2.2
and on the other page put only on the first DNS: 169.254.2.1
on the pc lan connection i leave the dhcp enabled "Obtain IP Address from serv" also for DNS (obviously cause i have the DHCP enabled on my router)
And MAGICLY all start works FINE!!!
After hours and hours spent on configurations, the problem was "simply" the windows firewall, but also the configuration of Remote Host-NDIS is important
Hope that can be useful for other
Right now i don´t have the MARY rom but the TUGA V3 ROM and problem continues. I have already tried to setup Remote HOST- NDIS like that and it didn´t work too.
Anyway thanks for all your help.
Thanks
Use the SD Card Method...
I use the SD Card Method. MUST BE FORMATTED AS FAT32 first. (As per willowxda's post. Thanx Willowxda)
Copy SSPL_TRIN.exe to your SD card's Root folder. (Included in ZIP File)
Rename the RUU_signed.nbh file in your OEM Rom to TRINIMG.nbh
Copy TRINIMG.nbh to your SD card's Root folder.
Run SSPL_TRIN.exe from your device.
Allow it to Flash and Restart as needed.
Works like a charm...
cabexas said:
Hello,
first of all, i want to thank you all for this great forum.
I have a small problem. I have bought a few days a HTC P3600. Everything was working fine.
Yesterday i tried to upgrade to wm6 using MARY 3.4.1 with sucess following the upgrade guide in trinityguides.info.
I have installed the Des’ Crash-Proof SPL and then flash the MARY 3.4.1 ROM.
Until now everything is working fine except the active sync. I tried to AS with the usb cable but it won't connect. It gives me the following error:
"Communication Error:Cannot start communications with the desktop computer. Remote Networking could not start due to a critical error (Error 608). Please reconnect your device. If the problem persists, restart your device using the instructions provided by the manufacturer."
I've googled it and tried all the suggestions that i could find, with no success.
If i connect via BT there is no problem.
The problem is that i want to put back the official ROM from HTC and if i can't connect with active sync via usb, i can't restore it.
BTW, if i put back the official ROM, the Hard-SPL is also flashed to the original??
Thank you
Click to expand...
Click to collapse
it is very simple but it took me too long time to figure out.
My PC hangs several times, I thought it is related to DMA or to IRQ interrupt requests for the microproccessor, but failed to solve it. This problem never happened to me while I was having the Qtek ppc, and even when I used the official HTC ROM when I bought this TrinTy. Then I started to check everything related to USB connection till I catch it. it is very silly, just to clear one checkbox.
Here what worked for me:
Click Start > Settings > Connections > USB to PC
you will find a checkbox......Just uncheck it. --------> Thats to disable advanced network functionality.
I believe it should work for you.
Try POWER + CAMERA + SOFTRESET (this enter the bootloader mode) and then install the ROM you like ... you will get no errors !!!
Click Start > Settings > Connections > USB to PC
you will find a checkbox......Just uncheck it. --------> Thats to disable advanced network functionality
Click to expand...
Click to collapse
That was the first things that i tried to do, but with no luck.
Yesterday, i did what nightfear suggested and it worked fine.
As soon as i restored the official rom, AS started to work like a charm.
That is a strange issue, but for now it's resolved.
Lets see if the problem doesn't come back when i put WM6 on it again.
Thank you all for your help.
Mini SD card must be formatted in FAT32 for flash update to work
I have been trying to upgrade flash via SDCard but it did not work no matter how hard I tried (switch btw hardspls).
Then I realised that I have to format the SDCard to FAT32 so that the Hard SPL can recognise the card in bootloader prompt.
I am using Hard SPL 1.30
I have flashed into the E1 English ROM (the one without the opera browser) and encountered some issues, I might have had them in previous ROMs as well, and I am wondering whether there is a solution for them:
1) Cannot set the IE homepage, it will always refer back to SamsungMobile
2) Cannot sync via Blue-tooth, even though a partnership is set with my PC, and ActiveSync is enabled I keep getting a message: "Cannot connect using Bluetooth to a PC that supports ACtivesync. You may be out of range. Would you like to create a bluetooth partnership with a different PC?"
Clicking Yes does not help here and the Bluetooth wont sync
Did anyone find a resolution for this matters?
i have the original E1 rom, i dont think the activesync prob is related to the rom as mine has no prob activesyncing using BT since the A1 rom.
btw make sure u are using the latest activesync on the pc.
use your phone to detect your pc, not the other way around, then try activesync. if u still cant, use your pc's BT to establish a serial connection to the phone, then start activesync on your phone.
Okay, I have tried a good 6 different roms, and for some really strange reason no matter what rom I use, from full manila to standard 6.1, using the sdkcerts update or not, my weather will only update via activesync. When I update and I'm not tethered to my usb cable, weather will connect to media net without an issue, but then will come back saying it can not update with the city I have listed. I have the correct information, because again, it will update via activesync. I'm not sure what the issue is because it follows with any rom I have tried. Does anyone know what might cause this? I can access the web, youtube, anything via media net 3g/gprs without an issue, so it's not the connectivity on my hermes. I'm currently on Tia's manila 2D 20954 rom. Thanks!!
I am Havein The Same Problem