O2 ATOM..........PLZZZ HELP - Upgrading, Modifying and Unlocking

Hello everyone,
well i have differnt question/ issues with my O2 atom:
a) this atom has ROM version 20051123B2 & Radio version MN1XN_PDA_051122. can any one recommend me as to what rom version should i upgrade it with.
would upgrading the ROM harm it? I badly need to upgrade as its probably one of the most initial atom realeases and its too slow to work on.
B) the phone has no smart dial option/software. I tried to install a software intellidialpro but it doesnt work.
C) Doesnt work well if i use as external usb modem connecting it with my laptop. the browsing & incomming bytes tends to stop after initial 10 minute usage and i have to disconnect it and reconnect it all over again to be able to use internet (that too for max 10 minutes)
F1

Related

ARTE100

Hi, can anyone help me and tell how to make hard reset on htc ARTE100?
Thanks
http://wiki.xda-developers.com/index.php?pagename=Artemis_Resets
Thanks, it works.
Problems with Room, Bluetooth, Wifi, overall System Restore needed
Good evening .
I have been trying to solve a problem that i have with my o2 xda. The problem is that the Bluetooth device is not working, it won’t even start, and I tried to turn it on from the communications manager but nothing. I tried to turn it on from the settings/communications/Bluetooth/turn Bluetooth make it visible to devices, but also nothing.
It turns on when I soft reset the device a few times, than sometimes it comes back on with the Bluetooth on, blue light flashing, but I’m unable to get it to pair with any devices. Sometimes my laptop will pick up the signal for a few seconds, but it is not able to sink with device.
I have tried everything I could think of, even have done some hard resets but nothing.
Someone told me to do an Artemis reset. So I downloaded the 4.02 with cube zip that I found around this website, but since I have never done such a procedure, in fact this is my first time with windows mobile, so I didn’t want to mess it up.
I read in this forums that third party applications can cause sometimes this problems because of driver contamination , my device did have lots of extra apps so that could be the problem .
In any case I’m not an expert, not even close especially with this system, so any help / suggestions / diagnostics / instructions, will be greatly appreciated.
The device is an o2 xda with built in gps, running windows mobile 6.1.
ROM Athemis Touch 4.02 WWe
Rom date : 4/8/8
Radio Version : 03.08.90
Protocol Version : 4.1.13.52
CPU: OMAP850
Speed: 201MHz
Ram: 64MB
Flash Size 128Mb
Data Bus 16bits
Storage size 44.74MB
And if the best solution is to do this artemis reset, i will really appreciate some instructions on how to exactly do this task, and if there is any known issues of this procedure killing the phone? , since sometimes with this types of "resets / flashes” this type of devices sometimes dies! So any help will be appreciated.
Thanks a lot.
Hope Corporation .
hi, have anyone schema arte100 (htc p3300)? thanx.

Help with Weird Problem: VP3G 3.60.1

Not sure if this was on the fault of my carrier or not, but I actually had this problem before and resolved it once.
I was running 3.60.1 and even tho I had Unchecked "Enable Advanced USB Connection" or whatever under USB to PC in the Connections Tab, My phone would not connect to WMDC (I use Windows Vista). I would just connect to get my contacts via Bluetooth, which worked fine.
I am a heavy user of tethering via USB as I like to charge the phone while I am connected. 3.60 series has been pretty good...I haven't had a complaint really since I upgraded from 3.0 (Which IMO is a bit more stable but I'm not sure why). Every once in awhile, I lose connection. I'm not sure why it does this. I'm using radio 1.48 and I have been using it for both 3.0 and 3.60. I had problems using 1.50 as data connections would drop instantly...so I never caught on to that radio. I am located near the NYC Metro area.
The latest problem I had was...sometimes my data connections would drop and would not reconnect without restarting the phone. I'd SR the phone and all of a sudden during the boot (while still connected to USB), my WMDC picks up the device. Not sure why it chooses to do it after I've had the ROM Flashed for several days now...but I go ahead and set it up only to see my phone assumes a permanent Flight Mode. Under Comm Manager, I am unable to switch back to Phone Mode. I do not have access to Phone settings. I cannot even open my dialer.
I've done it before and I don't save that many new things to my phone...so I went on to HR. After HR...the phone was completely unstable. During the loading of the "customizations" (which correct me if I'm wrong...is the EXTRom), it will install everything and then hang after finishing the last one which I believe was the theme of ATT.tsk.
Frustrated, I decided to flash back to 3.0 I still use 1.40Oli (HardSPL V6) which was always fine and I was never able to update to 2.10Oli for I have weird issues with SSPL and Vista. I do everything normally...I get to the progress screen. It hangs. No problem. Run RUUWrapper again...bootloader screen is accessible and my SPL and HTC_BOOT should be unaffected. Still hangs. I try to flash a radio...hangs. Almost everything I try to flash...hangs.
I've tried multiple USB Cables...thinking that was the problem...same problem though. It gets all the way to the progress and the Bootloader screen recognizes when its plugged to the USB so I don't think that's the problem.
My phone is stuck in bootloader right now and nothing will flash to it. No matter what it will get to progress and load 0% of any NBH I try to flash.
The main point of this post:
1. What caused 3.60.x to not connect to WMDC from the beginning via USB...only to do it randomly later?
2. What caused the corruption to the ROM leading me "GSM-less" stuck in Flight Mode and no access to anything to turn it back on to Phone Mode?
3. What is the cause of my phone not updating any NBHs I try to flash (OS Only/Radio Only/Original Shipped) ROMs?
I'm not sure if I was the only one receiving these errors. I have not updated my signature in awhile but I was running:
HARD-SPL V6: 1.40.Oli
Radio: 1.48.00
ROM: VP3G 3.60.1
Thanks for your help in advance.

Flash a Rom without USB Connection

Hi All
Just a quick question - I have a 2nd XDA Orbit which is running standard WM5 OS.
Unfortunately, I dropped it and the USB connection doesn't work. I don't use the connection much as I can do most things via cabs/email etc etc.
However I cannot apply a new ROM (B&B or Artemis 2.1 etc). Am I right to assume this can't be done via cabs etc?
Read here: http://wiki.xda-developers.com/index.php?pagename=HTC_Artemis

T-Mobile MDA Compact III issues...

Any help would be great....
I have a MDA Compact III issue when trying to upgrade to the ARTEMIS TOUCH 2.1 or 2.0 software
Unfortunatly, my pda was at 49% charge when i first tried, so stage one got to the end, then told me to charge my fone more and ended.
Thus i charge the fone to 75% and re-started. However, upon reconnecting the fone to commence the restart, the USB device was not recognised.
After removing the Active Sync and indeed the USB Driver from the PC and re-installing it, the conenction was re-established, however, it now often drops the connection. Plugging away, i tried the install Step 1 once more, and upon getting to 100% in the cmd part, and then progressing through the wizard, whereby the PDA displayed the progress bar reachinbg 100% (of the unlock stage) the PDA then reboots, and the connection is lost...and doesnt re-establish itself....and then the wizard reports Error [270] : Update Error The image file is corrupted. Please check your update Utility
Now, i have tried various sources for the software, and indeed tried both 2.0 and 2.1.....
Now i have a PDA that intermittantly drops its USB connection (and needs the USB removed and re-added on the PC) and is now slower than it was, plus never got to step 2 to get the software on iot.....
Can anyone help? Else i have a broken phone so to speak.....
Thanks alot in advance
Paul
paulcharles1 said:
Any help would be great....
I have a MDA Compact III issue when trying to upgrade to the ARTEMIS TOUCH 2.1 or 2.0 software
Unfortunatly, my pda was at 49% charge when i first tried, so stage one got to the end, then told me to charge my fone more and ended.
Thus i charge the fone to 75% and re-started. However, upon reconnecting the fone to commence the restart, the USB device was not recognised.
After removing the Active Sync and indeed the USB Driver from the PC and re-installing it, the conenction was re-established, however, it now often drops the connection. Plugging away, i tried the install Step 1 once more, and upon getting to 100% in the cmd part, and then progressing through the wizard, whereby the PDA displayed the progress bar reachinbg 100% (of the unlock stage) the PDA then reboots, and the connection is lost...and doesnt re-establish itself....and then the wizard reports Error [270] : Update Error The image file is corrupted. Please check your update Utility
Now, i have tried various sources for the software, and indeed tried both 2.0 and 2.1.....
Now i have a PDA that intermittantly drops its USB connection (and needs the USB removed and re-added on the PC) and is now slower than it was, plus never got to step 2 to get the software on iot.....
Can anyone help? Else i have a broken phone so to speak.....
Thanks alot in advance
Paul
Click to expand...
Click to collapse
well, I'll just try to give you some suggestions as I don't know much about MDA Compact III ,it does not fall in the category of wizard,it's a Magician device and I'm a wizard k-jam user. anyhow as a general of upgrading is to have your battery fully charged or atleast must have more than 70% charge.cuz during flashing in RUU upgrade mode,it does not charge,so if while during flash something goes wrong or it takes more time to flash,it shud have enough power to go through the whole process.if it does not have enough power to complete the process,it fails to flash properely and thus have a bad flash creating problems.so same has happened with u, you have a bad flash
well in wizards we have certain methods to revive the device or recharge the battery,i have no idea about your device,but can only suggest get the battery charge,secondly your usb connectivity problem is also due to the bad flash,cuz as there is no OS info on the device,it wont be able to establish the connection,which windows are you using,try to upgrade with winxp sp2 and active synchronize ver 4.5
as i have no idea about Magician upgrading method so wont comment further,but advise you to look in the below thread,it might be helpful,cuz its about Magician MDA Compact III
As your posting in the wring forum you might not get much help here,ok
http://forum.xda-developers.com/forumdisplay.php?f=276
good luck
thanks
thanks for the reply. Got it working - used 2.0 to unlock it, and 2.1 for the actual rom upgrade...

O2 Xda Bluetooth Problems - System related - Reset Info, advise Required.

Good evening .
I have been trying to solve a problem that i have with my o2 xda. The problem is that the Bluetooth device is not working, it won’t even start, and I tried to turn it on from the communications manager but nothing. I tried to turn it on from the settings/communications/Bluetooth/turn Bluetooth make it visible to devices, but also nothing.
It turns on when I soft reset the device a few times, than sometimes it comes back on with the Bluetooth on, blue light flashing, but I’m unable to get it to pair with any devices. Sometimes my laptop will pick up the signal for a few seconds, but it is not able to sink with device.
I have tried everything I could think of, even have done some hard resets but nothing.
Someone told me to do an Artemis reset. So I downloaded the 4.02 with cube zip that I found around this website, but since I have never done such a procedure, in fact this is my first time with windows mobile, so I didn’t want to mess it up.
I read in this forums that third party applications can cause sometimes this problems because of driver contamination , my device did have lots of extra apps so that could be the problem .
In any case I’m not an expert, not even close especially with this system, so any help / suggestions / diagnostics / instructions, will be greatly appreciated.
The device is an o2 xda with built in gps, running windows mobile 6.1.
ROM Athemis Touch 4.02 WWe
Rom date : 4/8/8
Radio Version : 03.08.90
Protocol Version : 4.1.13.52
CPU: OMAP850
Speed: 201MHz
Ram: 64MB
Flash Size 128Mb
Data Bus 16bits
Storage size 44.74MB
And if the best solution is to do this artemis reset, i will really appreciate some instructions on how to exactly do this task, and if there is any known issues of this procedure killing the phone? , since sometimes with this types of "resets / flashes” this type of devices sometimes dies! So any help will be appreciated.
Thanks a lot.
Hope Corporation .

Categories

Resources