Hello,
I'm interested to know more about wired headset.
I need it for answering when ride my moto. (this is why I don't need BT headset - but I have it)
Well, here in My country i didn't found a headset for Uni, because they are too rare.. and Uni have an 3,5mm jack, not 2,5mm as used in lot of gsm phones.
So, if anyone has skematiks, how to build headset for Uni from other type of stereo headset, I would apreciate it.
Thanks in advance.
Basically, you can just buy a normal headset, then replace only the jack. All headsets (should) have the same impendance(did I spell that right?), so no modification to the headset itself should be needed.
Just get a 3.5mm 3-channel(not the general one, you need the extra channel for the mic...but I guess you already know that) jack from an electronics store, cut off the original, identify the wires used(using a multimeter, or linking it up to another cable playing music), and splice on the new 3.5 mm one used. Just be sure to insulate the wire joints well so they won't accidentally short-circuit.
There: one 3.5mm headset, ready for use. Maybe slap on some cosmetics to the joint, so it won't look that ugly and homemade(a heat-shrink tube should do the trick, along with some padding to give it a some taper like those on factory-made jacks.
Good luck with your MacGyvering, mate!
Very thank you..
Your idea is super.. the only thing is that I never seen a 3,5mm jack with 3 chanells.. but I will search for it..
After I will do the trick will post back the results.
P.S. as subject of meditation.. did you ever seen another phone model which use a 3,5mm jack at headset?
Related
Just bought a car...
Added a little Brodit powered cradle for the Universal + GPS device.
Now I want to have it talk sexily to me through the car speakers... how might I go about doing this?
I've not really seen a car kit for the Jaguar XJ6, but I suppose this would be a good bet?
Thanks!
Ferg.
Hey, I've got a '97 Jag XJ, I had to make my carkit from separate bits. Don't have the Universal but Imate Jam- principle is the same I guess
Check out my post here:
http://forum.xda-developers.com/viewtopic.php?t=36123&highlight=
Charges my device as well as outputting all sound to car speakers.
Nice one sh,
Mine's a 97 too. Bloody nice beast.
I'll check out your instructions, although am I right in thinking this doesn't have a microphone or anything? I'm new to car kits etc so excuse my ignorance, but does this not hinder the thing a bit?
What does this setup NOT allow you to do?
Thanks again,
Ferg.
Well because I was too tight to buy a full carkit- I made my own (yes I do own the Jag- matter of principle for me!)
Well I've haven't spoken much about the audio side of things in that post... but all I've got is a 3.5mm to RCA cable going into the back of my car stereo.
There is also a 2.5 to 3.5mm adapter to accept the connection on the JAM. Now, you can get these adapters with built-in mics:
http://cgi.ebay.co.uk/2-5mm-to-3-5m...714269100QQcategoryZ14419QQrdZ1QQcmdZViewItem
I don't need it because I have my personal bluetooth kit when in car. So thats the only thing 'missing' if you like- although I've setup it up so I can change this adapter for any type that has 3.5mm on one end.
Send me a link to the holder that you've got- I take it doesn't have an audio out on it?
i made up my own too for the charmer, dont own a jag and havent wired it into the stereo but have stashed a set of "ipod" type speakers under the dash instead.
not wanting to play audio but just wanting to have handsfree use of phone and amplified audio from sat nav.
not running it through the sterao also means the missus and kids are happy with the radio/cd playing and i still get to hear the satnav guidance.
i bought a couple of incar mics and soldered the whole lot up onto a butchered wired headset (the one that came with the charmer)
details http://www.modaco.com/hardwired-incar-handsfree-the-diy-way-t240297.html
although i still havent got round to putting up pics yet
Can anyone recomend a replacement for the standard stero handsfree kit that comes with the MDA Pro.
I've seen these http://www.mobilefun.co.uk/product/10098.htm, but was wondering if anyone knew of any better ones?
I'm also looking for such a headset. The one on your links looks nice, but is there a volume control on it? I can't see that.
The one in mobilefun.co.uk is just the same as the one came from the box.
There is no other alternative so far I could find....
Though I found one (and I ordered already) from
http://pc-mobile.net/pqtaa.htm
that is for a 3.5mm headphone/mic jack.
So, I will post again if this really fits the Universal....GOOD LUCK!!!
Cheers,
Yeah, the headset fits without any problem.
That is the same as the HP Ipaq 54xx/55xx/63xx/65xx, Toshiba e75x/80x.
Although its a bit expensive, USD33 including postage....
Cheers,
Just out of curiousity, what happened to your hands free kit that came with the unit, guys?
The original one comes with the package is excellent except that it is too lengthy and the pair of earphones always messes with others.
I would like to have a single lead earphone that I can change to stereo when I want.
So, the one that I just got is perfect but it is quite easily to be damage....
Cheers,
:twisted: :twisted: My over excited dog snagged them with a paw when I got home from work and I think she snapped the cable inside the sheathing.
Wired headset with headband with wires
Can anyone recommend a headset for the Universal that
IS NOT BLUETOOTH
Has a headband with good sized speakers, not earbuds and dangly wires
IS NOT BLUETOOTH
Microphone, PTT switch, volume
and isn't bluetooth? i.e. it's wired to the 4 pole jack?
Thanks
Nick
Hi Chris,
Thanks for the info!
I have one of this headset that I bought few years ago for my XDA/Wallaby (with the 2.5mm plug). Yes, its very easy to be damaged (very delicate) but yet mine is still functional until now. Some part of the wire is already torn and I have to put some tape on it.
I use it mainly to connect my XDA/Wallaby to my car stereo system.
Thanks that you share this info, now I know that there is a suitable version for the Universal as well.
Do you mind to confirm back that the headset indeed works perfectly with the Universal:
1. The call answer button
2. The microphone
3. Volume control
4. The stereo jack
I will definately get one if you can help clarify that every point is working fine. Thanks in advance.
Yeah. Everything is fine altough the answer key need more practices.
Good to hear that the info is usefual.
Cheers,
Thanks Chris!
The answer button, you just press it once to pick up a call right?
What special practice do you need?
I sticked my old one (for the XDA) in my car dashboard near the stereo system. So when the phone rings, I just press it once and the call then will be in the car speakers. The microphone is not that great, ppl usually complaint me that my voice is so low, but guess what, they indeed can hear me.
lie_ui said:
So when the phone rings, I just press it once and the call then will be in the car speakers. The microphone is not that great, ppl usually complaint me that my voice is so low, but guess what, they indeed can hear me.
Click to expand...
Click to collapse
This is exactly what I'm trying to set up in my car,how do I do it? I tried using a splitter (one 3.5 mm male plug with two female 3.5mm openings) and running one end to my car stereo, and the audio from the call comes through the car speakers nicely but I can't use either the mic from the included (in the box) headset for voice nor will the device's mic work...
Anyone interested in this topic to advice to make our own Headset
Count me in
I would be interested. The headset supplied is not very good: the earpieces don't stay in place to get the best sound and the wires are to 'wirey', ie they're not soft enough, and they don't lay straight.
I had seen before someone had taken the Nokia hands-free headphones (similar to the Universals, with a central piece with a mic and button on) and they manages to fit a tiny 2.5mm stereo socket in it, so any standard headphones would plug in. But on the Universals, I don't think there's room.
www.remtrak.com sell 4-way Jack Plugs (3.5MM Angled or Straight) so we could feasibly manufacture our own, with the corrct pin out.
L, R, GND, Mic - But which is which?!
I have an old 80's BT Viscount Handset removed from it's phone base and itching for headset duties. . .
shaju said:
Anyone interested in this topic to advice to make our own Headset
Click to expand...
Click to collapse
Instead of making one how about one of these?
http://pc-mobile.net/pxuaa.htm
Matt
I don't see how that helps me hook up a Pokia, Novophone, or connect my own home-made devices. But good link for Non-Geeks!
Any adaptors that will allow me to use proper 3.5 inch headphone jack in place of the mini USB ones ( i dont like the in ear phones) checked ebay and couldnt see anything?
you want get one of these http://www.expansys.com/p.aspx?i=142090 - Mike
Ouch, that thing is both horribly badly designed and prohibitively expensive- it's going to stick out what looks like an inch by itself, most headphone plugs will add another inch on top of that- I need something that fits flush with the bottom of the phone (comes out at a right angle) AND supplies an input for the charger. One can only dream!
The orbit would make a great on-mains Wifi internet radio if such a gubbin existed- hook up some speakers, start TCPMP, sorted!
in which case if you don't like wires stop messing around and get a set of A2DP compatible headphones - the quality is very good, but far more costly than a cable addaptor - the choice is yours - Mike
Might have been worth while if I didn't use an iPod for all my portable audio needs- have you seen any A2DP compatible speakers around?
Looks like there are hacks out there, but no official products, the combination really would just turn the Orbit into an incredibly expensive Wifi radio! But where's the fun in just going out and buying a proper one!
Have a look at the products made by Parrot there are a few Bluetooth audio add on boxes, I fail to see the relevance to WiFi?? as the A2DP profile is Bluetooth - it even works on the T-Mobile MDA-CIII which has no WiFi - Mike
I say wifi radio because I listen to internet radio stations around the house using the Orbit, and the ol' tinternet comes via the wifi doohickey!
A2DP is, of course, a bluetooth profile and would be the method over which I get decent sounding audio from the Orbit to some speakers whilst still having the Orbit plugged into mains so the battery doesn't get sucked dry... that said I think the Orbit will last a good few hours streaming internet radio, although I have yet to put that to the test.
My other solution would be, as mentioned above, an adaptor that allows both the charger AND headset to be plugged in- I can't see this as being technically impossible.
With a brief cursory investigation I have discovered, I think, that the headset uses a proprietary 6-pin connection on the opposite side of the mini-usb connector. The headphones do not use the 4-pin standard mini-usb connector on the other side, but a connector that uses both should be reasonably simple to produce. Ergo it should be childs play for a third party to produce an Artemis dock that contains not only a connection to USB but a standard 3.5mm amplified microphone socket alongside a standard 3.5mm amplified stero audio jack... not to mention a button on the front of the dock for picking up calls and a volume slider if you really wanted them.
Call me crazy, but I want one of those!
You could try this
http://www.expansys.com/htc/p_htc_item.aspx?i=145066
Might do the trick even if it is a bit long
Rich
Dear lord! You've made my day! Hmmm, a little jiggery pokery and I might even be able to incorporate that into a dock but it'll be fantastic for charging and listening to net radio at work- takes that little extra load off my desktop PC.
Cheers!
Glad I could help
richiev4 said:
You could try this
http://www.expansys.com/htc/p_htc_item.aspx?i=145066
Might do the trick even if it is a bit long
Rich
Click to expand...
Click to collapse
Hi,
Does anyone know if the above would work with a set of mini stereo speakers with a 3.5mm headphone jack (like the walkman speakers i used to have, back in the day...) to listen to the FM radio while charging the phone from mains? Or would you still need the headphones plugged into get any FM reception?
Daft question maybe, but I wondered whether the device would just use the speaker wires as an antenna instead of the headphone wires?
It will work fine, I am going to use mine to connect my orbit to my home stereo and charge it at the same time.
Rich
2.5mm 3 pole jack plug
Hi,
Anybody know of an Artemis mini usb to 2.5mm 3 pole jack plug adapter which allows the connection to deliver audio and microphone capability ?
I would like to connet my Artemis/Orbit to the Autocom intercom system on my motorcycle . This uses a lead with a 2.5mm jack plug at the phone end and a 3.5mm jack at the Autocom system end. Both are 3 pole.
Thanks
P.S. hope you don't mind me jumping in your postings
http://www.expansys.com/s.aspx
try doing a search for "2.5mm"
A very good Items for the Artemis on EbaY :
look :
http://cgi.ebay.fr/FOR-ORANGE-SPV-E...ryZ14419QQssPageNameZWDVWQQrdZ1QQcmdZViewItem
2.5mm 3 pole jack plug adatper
I think I've found exactly what I'm looking for at:
http://igonemobile.com/products/html/61315310.html
I've got one on order and I'll let you know if it works.
cegmawr said:
Hi,
Anybody know of an Artemis mini usb to 2.5mm 3 pole jack plug adapter which allows the connection to deliver audio and microphone capability ?
I would like to connet my Artemis/Orbit to the Autocom intercom system on my motorcycle . This uses a lead with a 2.5mm jack plug at the phone end and a 3.5mm jack at the Autocom system end. Both are 3 pole.
Thanks
P.S. hope you don't mind me jumping in your postings
Click to expand...
Click to collapse
Is this so you can listen to music from the Orbit? I've had difficulty on my bike with this...music cuts out and wont restart after phone call is over. In the end, I bought the Autocom bluetooth dongle and now bluetooth the Orbit to the bike. I get phone calls and GPS just fine, but I use a wired iPod for music.
cegmawr said:
I think I've found exactly what I'm looking for at:
http://igonemobile.com/products/html/61315310.html
I've got one on order and I'll let you know if it works.
Click to expand...
Click to collapse
Does this support the Artemis? It isn't in the list....
There was a posting for the mini USB PinOut some Time ago. Look in the wiki Section to find it. Here is what they showed up with.
Maybe This will Help someone to build their own Adapter or whatsoever.
Greetings
Jabami
so what was the general concensus with using Autocom? Did the 2.5mm jack work?
I want to avoid using the bluetooth option on autocom, since I might just as well go for a Scala bluetooth headset instead if the jack doesnt work...
Hi,
I plan on using my desire in the car and playing music through my car stereo's aux input. But I dont really want to be picking up the phone to skip forward and back through tracks. The headset that ships with the phone has great inline controls that work with spotify. So I was wondering if anyone knows of a company that makes a cable that has a 3.5mm jack at both ends (i.e. one end into the phone, the other into the car stereo) but also has inline controls. I could then find a way of mounting the inline control somewhere on the dash.
Any advice is greatly appreciated.
Paddy
I have done this in the past by cutting the headphone ends off a cable and then soldering this to a 3.5mm jack plug available from electronics shops etc, not too much of a job to do, but will prob mean you have to find another htc headset with the controls if you want to keep your original headset
Haven't seen this no, but it should be easy to fix.
Either just solder the cable yourself, or just buy a 3,5 to 3,5 cable and insert it. Should solve your issues. Just ordered the Griffin SmartTalk which has inline controls and a 3,5mm jack output myself, it had good reviews for the iPhone and should work well with the my Desire aswell.
Zappza said:
Just ordered the Griffin SmartTalk which has inline controls and a 3,5mm jack output myself, it had good reviews for the iPhone and should work well with the my Desire aswell.
Click to expand...
Click to collapse
Let us know how you get on with it please.