noob needed help - 8525, TyTN, MDA Vario II, JasJam ROM Development

my hermes got "no gsm" , after i upgrade it to wm6
so i read the "wiki"...i found that i bricked my radio rom
SPL HTC_BOOT Boot OS? No GSM? KITL Diagnostic
Any Any Yes Yes --- bricked while flashing
radio, OS can boot
Solution
1. Flash Hard-SPL
2.Flash any radio in NBH format
Do both steps using SSPL+ActiveSync
i am matched with this situation
but i got confuse with the step 2
should i use the Radio 1.43.00.00(ftp://xda:[email protected]/Uploads/Hermes/Radio 1.43.00.00.zip)
or (ftp://xda:[email protected]a-developers.com/Uploads/Hermes/HERM_Radio_Only_1.43.00.00_CustomRUU.rar)

kuetsum said:
my hermes got "no gsm" , after i upgrade it to wm6
so i read the "wiki"...i found that i bricked my radio rom
SPL HTC_BOOT Boot OS? No GSM? KITL Diagnostic
Any Any Yes Yes --- bricked while flashing
radio, OS can boot
Solution
1. Flash Hard-SPL
2.Flash any radio in NBH format
Do both steps using SSPL+ActiveSync
i am matched with this situation
but i got confuse with the step 2
should i use the Radio 1.43.00.00(ftp://xda:[email protected]/Uploads/Hermes/Radio%201.43.00.00.zip)
or (ftp://xda:[email protected]/Uploads/Hermes/HERM_Radio_Only_1.43.00.00_CustomRUU.rar)
Click to expand...
Click to collapse
use the radio 1.43 (first option you have there) ftp://xda:[email protected]/Uploads/Hermes/Radio 1.43.00.00.zip)

walshieau said:
use the radio 1.43 (first option you have there) ftp://xda:[email protected]/Uploads/Hermes/Radio 1.43.00.00.zip)
Click to expand...
Click to collapse
I got a bigger problem..
my pc suddenly shutdown....while upgrading the rom..
my hermes is stuck in the bootloader screen
it can detect the usb sync
but the upgrade program cant find my hermes with and error
what should i do now?
T_T

I'd recommend you check out the WIKI for upgrade problems HERE. Also there's a section on what to do if you've bricked your phone HERE.
Hope this helps

Related

Universal RUU - CID Checking bypassed

Hi, after speaking to Midget_1990, I have patched the RUU for the Universal to allow flashing with any CID on your phone, this is the official Universal RUU (with a slight GUI mod by someone Midget_1990 mentioned)
so have at it... enjoy.
thanks, was just about to upload it
thanks,
just downloaded and have a try
allway said:
thanks,
just downloaded and have a try
Click to expand...
Click to collapse
it does work... just has the minor caveat that it'll try to flash a Universal when it's not actually plugged in... so try not to be a complete plank with it.
Olipro said:
it does work... just has the minor caveat that it'll try to flash a Universal when it's not actually plugged in... so try not to be a complete plank with it.
Click to expand...
Click to collapse
i have flashed my universal with the new RUU.
It works fine.
Olipro
Is it possible that you will make a HardSPL for Universal?
We still have no way to recover bricked radio...
we were discussing that earlier. the nogsm shows when the radio bootloader is not written to the device properly for whatever reason. its still early days but it may be possible to create a new radio bootloader that cant be overwritten so that problem wont occur. however it wont fix thoses who allready ahve the problem.
Skwyk said:
Olipro
Is it possible that you will make a HardSPL for Universal?
We still have no way to recover bricked radio...
Click to expand...
Click to collapse
ok, if you are flashing a radio, and you brick your radio, but not the radio bootloader, then you should be able to recover by reflashing.
if you brick the Radio bootloader, then unfortunately, there is no way for you to recover from this; possibly the only way of recovery is directly accessing the radio chip pins via whatever interface it is... perhaps i2c? and flashing on a radio BL again through a separate interface... meaning you then need a radio bootloader binary in the correct format.
Olipro said:
ok, if you are flashing a radio, and you brick your radio, but not the radio bootloader, then you should be able to recover by reflashing.
Click to expand...
Click to collapse
Not in 100% of the cases... there are some situations where the radio bootloader is intact, but the radio is screwed, this causes all bootloader commands that require radio seclevel to be queried to hang the device (like 'task 32' or 'info 2'), thus not being able to flash it with the usual RUUs.
If this happens, it can easily be fixed with hermflasher by flashing the raw radio without prior authenticating to bootloader.
Olipro!!! am having No GSM here!!!
Dear Dr. PDAs
My Universal is suffering for bad blocks of Radio ROM i guess.
it Says NO GSM when boots.
Boots WIN CE very well
can't flash radio rom.
Please tell if we could have HardSPL for Universal or is there any other way to recover it...
waiting.
farehmani
hi everyone i m in need of new rom for my XDA Exec Universal plz help me as i m ver new.
V1640 and flash rom radio problem
hello,
On my V1640 my radio rom is version :0.00.00, and I can't flash it with a newradio rom. It is probably a CID Lock problem, How works Universal RUU ?
Is there a tutorial for flashing with Universal RUU ?
thanks
Regards
Has anyone got anywhere to fix problems with radio mess ups I have an O2 XDA Exec and loads 2.05 ok but error when flashing any Radio. Tried all I can find but no luck
simpleparab said:
hi everyone i m in need of new rom for my XDA Exec Universal plz help me as i m ver new.
Click to expand...
Click to collapse
Try to serch forum
Or, for lasy people try my folder blow
Flashing radio rom Ok !!!
I flashed the radio rom on another PC.... It works fine.
Try this..good luck
Flashing the O2 original ROm with this RUU
Hi,
Can i use this RUU combined with the original ROM from O2 to flash?
My current ROM:
ROM 1.13.82
Radio 1.04.02
ExtROM 1.13.188
New ROM available:
ROM 1.30.107
Radio 1.09.00
ExtROM 1.30.162
I have to use the bootloader mode to flash the new ROM because my XDA Exec has problem on connection with my PC via Active Sync. My Xda just dont sync with my PC where there is no connection established.
Hopefully someone can tell me what is this RUU? Whats the different than the original?
bejoa said:
Flashing radio rom Ok !!!
I flashed the radio rom on another PC.... It works fine.
Try this..good luck
Click to expand...
Click to collapse
this is the second time ppl have been able to flash no GSM Universals by using a nother PC. What was the spec of this pc and what was installed and Not installed in it.? I really want to unbrick my Universsal
I flashed my universal on a Laptop :
Gericom Select 2580+
AMD 2500+, 512 Mo ram, 80 Gb HD,
Windows XP Home SP2 pack
ActiveSync 4.2
Universal RUU
nothing special installed...
Good luck
bejoa,
what was the boot loader version of ur universal?
It is version 1.0

pls help - i can't flash my rom

Dear bros,
Please help! i can't flash my rom to LVSW 20070507
my computer has installed zip and .Net2 already.
and i follow the instruction to upgrade, then it suddently said that i need to do recovery.
Then i also follow the steps and re-start my Hermes, it doesn't return to bootloader and reboot normally. Then i click skip on mu computer and then re-upgrade again, but the prcoess just repeats and repeats to ask me to do recovery.
Can anyone tell me which steps i have omitted????
my IPL - 1.01
SPL - 1.40 Olipro
Rom version - 3.22.200.4
Protocol version - 32.50.7018.00H
pls help me!
thanks in advance!
Read this : http://forum.xda-developers.com/showthread.php?t=299462
Sounds like you've made a brick - but probably recoverable... First we need more information...
1. Are you SuperCID?
2. Did your computer or phone crash or become disconnected during the original flash?
3. What error number is dosplayed when you try to flash?
4. When you boot the phone does it show NO GSM at the bottom right? (This may only display quickly so watch the boot process carefully), or does it show a radio ROM version such as 1.27.0.0?
5. Are you running Vista?
When you get this sort of info you need to move your question to the 'Dead Hermes....' thread. I'd also suggest reading a lot of it (even though it is long).
karay215 said:
Dear bros,
Please help! i can't flash my rom to LVSW 20070507
my computer has installed zip and .Net2 already.
and i follow the instruction to upgrade, then it suddently said that i need to do recovery.
Then i also follow the steps and re-start my Hermes, it doesn't return to bootloader and reboot normally. Then i click skip on mu computer and then re-upgrade again, but the prcoess just repeats and repeats to ask me to do recovery.
Can anyone tell me which steps i have omitted????
my IPL - 1.01
SPL - 1.40 Olipro
Rom version - 3.22.200.4
Protocol version - 32.50.7018.00H
pls help me!
thanks in advance!
Click to expand...
Click to collapse
ach2 said:
Sounds like you've made a brick - but probably recoverable... First we need more information...
1. Are you SuperCID?
YES, I am superCID
2. Did your computer or phone crash or become disconnected during the original flash?
No
3. What error number is dosplayed when you try to flash?
it's ERROR 302, update error
4. When you boot the phone does it show NO GSM at the bottom right?
nth happened, just a normal reboot and the phone is just as normal as before
(This may only display quickly so watch the boot process carefully), or does it show a radio ROM version such as 1.27.0.0?
5. Are you running Vista?
No, i am running WIN XP Sp2
When you get this sort of info you need to move your question to the 'Dead Hermes....' thread. I'd also suggest reading a lot of it (even though it is long).
Click to expand...
Click to collapse
AND i have read the above link so many times and i have followed all the steps, but don't know what happened....
pls help!
thanks!!!
karay215 said:
AND i have read the above link so many times and i have followed all the steps, but don't know what happened....
pls help!
thanks!!!
Click to expand...
Click to collapse
Answer the questions then, don't just skip by them hoping by some miracle someone will know what your PDA is suffering from and give you the answer. What guide did you follow?
Fix from LegolastheElf​
1.40.oli has a bug (because the original BL it was based on had a bug)...
You need to upgrade to Hardspl 2.10, then flash LVSW.
hope it works for you
Even though this beginner submitted a really vague problem, it was resolved without insults. Hooray!
man, my thoughts exactly!
thanks bro~!
but i even can't flash to Hard SPL v.7
the problem is the same....
it asks me to recover again and again.....
karay215 said:
thanks bro~!
but i even can't flash to Hard SPL v.7
the problem is the same....
it asks me to recover again and again.....
Click to expand...
Click to collapse
you need to put the (HardSPL) nbh on your sd card as HERMIMG.nbh and then execute sspl on your device, it should upgrade to HardSPL then

Hard SPL Problems

i'm trying to upgrade to VP3g's rom and every time i install the latest version of hard spl it says its not detectable or it says unknown version use safe spl. i follow the mrvanx guide everytime,...... whats wrong???????????????????
nothing, go ahead and continue. I'm sure everything will be fine. It's happened to me several times with different Roms but I had no problems flashing.
choose spl version, if hard spl v7 choose 2.10 then continue
kazuya_gonzalez said:
choose spl version, if hard spl v7 choose 2.10 then continue
Click to expand...
Click to collapse
i bricked my phone..............
edited , double post
Symbian_Black said:
i bricked my phone..............
Click to expand...
Click to collapse
are u sure have hard spl v 7? (2.10 olipro?)
i also have a problem that cannot detect my version..
but i choose version 2.10.. and it works for me for upgrade any rom..
I don't what you did but if you have HardSPL on your device then you haven't bricked it. Put it into Bootloader Mode (Tri color screen) and connect it to your computer. Get a Rom , try Schaps, and run the RUU Wrapper. If you have HardSPL on it then you should have no problems.
i have also this problem but i klick the version of my spl and it works
aint nffin wrong laddie
all will be fine
if it dont auto detect it will default to safe
but check the next screen to see if it reads correct

Urgent! My diamond has hardware problem and need to fallback to stock ROM and SPL.

Hi,
My Diamond has no response on the screen, so I think I need to return to factory for repairing. However I have difficulties in falling back to stock ROM and SPL.
From the Wiki:
---------------
STEP BY STEP HOW TO RETURN TO STOCK SPL - FOR WARRANTY REASONS ONLY!
0. be sure to first restore stock OS, and stock radio. stock SPL is always to be done last!!
...
-----------------
I can't flash my ROM to latest HK WWE CSL ROM (2.03) as it just stopped at 0%. I'm using SPL-1.30.OliNex.
Questions:
0) Why? Any step I've missed? I've just copied the .NBH from HTC official ROM download. Should I get the .NBH from the Wiki instead?
1) Should I flash to v1.93 (the very beginning of the ROM)?
2) Must the RADIO be flashed back as well? or the above Stock ROM has included the RADIO already?
3) Anyone can give me a reference on the step-by-step in details...
Thanks!
Please help...
F810
Questions:
f810 said:
0) Why? Any step I've missed? I've just copied the .NBH from HTC official ROM download. Should I get the .NBH from the Wiki instead?
Click to expand...
Click to collapse
If the latest was the offical from the site then you could use that - as you are having issues flashing this with 1.30 HSPL, I would suggest updating that to 1.40
f810 said:
1) Should I flash to v1.93 (the very beginning of the ROM)?
Click to expand...
Click to collapse
This might be a easier option and should work woth the 1.30 HSPL
f810 said:
2) Must the RADIO be flashed back as well? or the above Stock ROM has included the RADIO already?
Click to expand...
Click to collapse
This is recommended
f810 said:
3) Anyone can give me a reference on the step-by-step in details...
Click to expand...
Click to collapse
Its really straight forward like the WiKi suggests
This Thread may help
Thanks a lot.
Re Q3, so do you mean if I extracted the stock NBH, it's only OS but not including RADIO? If so, I will get the RADIO from wiki page later. Would you please clarify for me?
After your information, I think the steps in Wiki are clear. Thanks.
If this is HK ROM is the one you have downloaded from HTC PAGE then it has a radio included
Since my Diamond is totally malfunction in the touch screen, I can't response to all the confirmation & prompts...
I've failed to install Stock ROM and tried your recommendation on upgrading to HSPL 1.40. There was a confirmation on running the program in my Diamond and I can't press YES and now my diamond is just like bricked.
I've also tried pressing VOL DOWN + Reset to connect the Diamond via USB. The ROM Update Utility has "successfully" update the HSPL, but actually when I hard reset it and found it's still running 1.30... Can I just use this approach to fallback to Factory status??
Anyone has good idea on how to fallback to Factory Stock ROM, RADIO and SPL, provided that my screen has totally no response to me?
PLEASE...PLEASE...PLEASE help.
You will not be able to update olipros Hard SPL in bootloader mode as the SPL is protected and the 1.30 will prevent this although show its been done.
What you will need to do then is just load a 1.93 ROM from boot loader. the were some in that link i posted earlier. as to reverting to the default SPL - you may be luck not to need the screen for any confirmation. but running a new SPL to overwrite Oli's you will need to use windows and the RRU
I've tried to load 1.93 ROM to my diamond but failed on OliNex 1.30. The link in modmydiamond.info on OliNex 1.40 Signed seems not correct, as it's still 1.30 after flashed. I've then flashed UNSIGNED 1.40 OliNex SPL (also downloaded from modmydiamond.info) and now flashing the 1.93 ROM in progress from bootloader.
I will flash the Stock SPL through the Bootloader after that...I hope I can successfully fallback and get it repair...
Last question (I hope), the stock SPL should be 1.37 so I want to confirm whether it can boot 1.93 ROM.
Thanks a lot!
Because these Unsigned HARD SPL 's are write protected.....you will fail all the time. Not sure if stock SPL can undue the write protection but if you still get stuck after you try then in order to bypass write protection I know Jump SPL allows for this.
band27 said:
Because these Unsigned HARD SPL 's are write protected.....you will fail all the time. Not sure if stock SPL can undue the write protection but if you still get stuck after you try then in order to bypass write protection I know Jump SPL allows for this.
Click to expand...
Click to collapse
you're right. When I flash the Stock SPL, it is "successful" but actually it doesn't update the SPL (i.e yet running OliNex 1.40). Where can I get the Jump SPL?
Here you go....I did a search
Hi,
Sorry to use this thread but im also trying to install back to my original Diamond ROM and am currently using the rom developed by Diamond Project (1.93.456.2WWE) and i kept flashing it back using Signed V1.93 RUU and apprently the Diamond project words still keep showing out when i start my phone!
How do i completely remove the Diamond Project thing? Thank you!
Read this............Scroll to Post #39
http://forum.xda-developers.com/showthread.php?t=400950&page=4
band27 said:
Here you go....I did a search
Click to expand...
Click to collapse
I also got that but it's not win32 program... I believe it's running on the Diamond. But I've hard reset, and never able to setup as it's screen was not functioning now...
kawatsu said:
Hi,
Sorry to use this thread but im also trying to install back to my original Diamond ROM and am currently using the rom developed by Diamond Project (1.93.456.2WWE) and i kept flashing it back using Signed V1.93 RUU and apprently the Diamond project words still keep showing out when i start my phone!
How do i completely remove the Diamond Project thing? Thank you!
Click to expand...
Click to collapse
That ROM had a different boot image - so you need to replace that by flashing another splash .NBH file using RUU.
Original splash can be found HERE
and if needed CUSTOM RUU HERE
Just un-zip these and put the splash file in the same folder as the Custom RUU and run the RUU - the flash should take a few seconds and viola - bye bye Diamond project splash.
f810 said:
I've tried to load 1.93 ROM to my diamond but failed on OliNex 1.30. The link in modmydiamond.info on OliNex 1.40 Signed seems not correct, as it's still 1.30 after flashed. I've then flashed UNSIGNED 1.40 OliNex SPL (also downloaded from modmydiamond.info) and now flashing the 1.93 ROM in progress from bootloader.
I will flash the Stock SPL through the Bootloader after that...I hope I can successfully fallback and get it repair...
Last question (I hope), the stock SPL should be 1.37 so I want to confirm whether it can boot 1.93 ROM.
Thanks a lot!
Click to expand...
Click to collapse
I think as long as the SPL is changed and the ROM is of the original language the I think it should be OK to send back like that
f810 said:
you're right. When I flash the Stock SPL, it is "successful" but actually it doesn't update the SPL (i.e yet running OliNex 1.40). Where can I get the Jump SPL?
Click to expand...
Click to collapse
As said before; you should be able to successfully run the stock SPL using RUU - if you are trying this via bootloader it will not work.
Which is the original SPL?? 1.23, 1.34 or 1.37? I do recall taking a picture of the original SPL when i 1st got the Diamond for days like that but i just can't find it now
I'm bought it from Malaysia. Anybody can help me confirm this??
R3PUBL1K said:
As said before; you should be able to successfully run the stock SPL using RUU - if you are trying this via bootloader it will not work.
Click to expand...
Click to collapse
I've tried to connect to ActiveSync successfully although the Initial Setup wizard on my Diamond. I've then run the RUU from RUU-SSPL-withoutNBH.zip and put the stock SPL .NBH file into the extracted directory. It can retrieve my device info, and when I confirm the update of ROM, after 3-5 sec it said about connection failure. I can browse the Internal Storage at the moment yet.
I've then tried similar thing using the Custom RUU inside the package diamond-hspl-1.34.zip. This time I can see 100% update. When I press VolDown and reset, the SPL is still v1.40 ONliEx.
What's wrong with my procedures above?
f810 said:
I've tried to connect to ActiveSync successfully although the Initial Setup wizard on my Diamond. I've then run the RUU from RUU-SSPL-withoutNBH.zip and put the stock SPL .NBH file into the extracted directory. It can retrieve my device info, and when I confirm the update of ROM, after 3-5 sec it said about connection failure. I can browse the Internal Storage at the moment yet.
I've then tried similar thing using the Custom RUU inside the package diamond-hspl-1.34.zip. This time I can see 100% update. When I press VolDown and reset, the SPL is still v1.40 ONliEx.
What's wrong with my procedures above?
Click to expand...
Click to collapse
I think I miss the step of running the SSPL-Manual.exe because of my screen is not responding... Anyway for me to put it into the Windows Startup Folder?? When I use ActiveSync I can't see Windows directory.
Please...please...I miss this step only...
f810 said:
I think I miss the step of running the SSPL-Manual.exe because of my screen is not responding... Anyway for me to put it into the Windows Startup Folder?? When I use ActiveSync I can't see Windows directory.
Please...please...I miss this step only...
Click to expand...
Click to collapse
Can anyone help??

[TUT] HOW-TO restore Diamond to stock for warranty

Due to a hardware problem in my Diamond I needed to restore it to manufacturer default. I didn't find a guide to this and since I've done the research anyway I thought I'd put together this little tutorial as the information was somewhat scattered around the forum. I hope this guide will be of use for the community.
My phone was originally branded and sim-locked by 3. After I was through with it, it was SIM-unlocked, security unlocked and had HSPL, custom ROM and a radio ported from another device. The steps below is what I did to restore it to stock. All steps might not be neccessary for you. This procedure might also work for other devices than the Diamond, but of course you need other versions of SPL, ROM etc.
1. Backup everything on your phone to your computer - use activesync, PIMbackup etc and make a copy of your Internal Storage.
2. Make a hard reset (hold vol down + enter and soft reset) and chose to format moviNAND. This step is only neccessary if you want to wipe your Internal Storage before you send the device in for repair, but I recommend it.
3. Go to www.htc.com and download the latest stock ROM (includes stock radio and SPL). You find it under Support and you enter your s/n to get the correct stock ROM for your device, complete with branding for your operator. You can also find stock ROMS here: http://forum.xda-developers.com/showthread.php?t=471699
4. Flash the stock ROM. Now you have stock ROM and Radio on your device. Stock SPL will not be installed until you've replaced HSPL with an older stock SPL and flashed ROM again.
5. Get RUU-SSPL and stock SPL from HERE:
http://forum.xda-developers.com/showpost.php?p=2324829&postcount=39. I used the stock 1.93 SPL. Some instructions and info about restoring stock SPL is in the linked post by cmonex and due credit goes to her. I will repeat some of that info to keep this guide step-by-step. EDIT: Stock SPL 2.03 can be found here: http://forum.xda-developers.com/showpost.php?p=3359191&postcount=390
6. Put the .nbh file from the SPL you downloaded into the same folder as the extracted contents of RUU-SSPL-withoutNBH.zip and run the RUU. This flashes an old stock SPL.
7. Flash your stock ROM from step 3 again. This step is neccessary to get the correct stock SPL on your device, eg. the one that corresponds with the stock ROM you've downloaded in step 3. It was not installed in step 4, because then you still had HSPL. In step 6 you've installed a stock SPL and now the correct stock SPL will flash along with the stock ROM. After this step I got SPL 2.03 on my Diamond.
8. Remove the Security Unlock from your device using the instructions and Security Relocker by Olinex from this post by cmonex: http://forum.xda-developers.com/showpost.php?p=3299516&postcount=492
Now, my Diamond is still SIM-unlocked. I have not managed to find any info about how to restore the SIM-lock, but it is hopefully not neccessary for warranty. As far as I can tell, the unlock doesn't show anywhere, but of course all they need to do is to try a SIM-card from another operator...
If anyone has info about how to restore SIM-lock, then I'll update this guide with that info.
good job...
moderator make this "sticky"
3dward87 said:
good job...
moderator make this "sticky"
Click to expand...
Click to collapse
I second that, it contains links to stock ROMs, that'll hopefully stop a million topics about it lol.
This does not work for me.. However i have a problem. the touch screen of my device is not working.. so i can't get pass the allign screen part .. and for somereason the ruu won't connect to phone when it is at tha part so i can't install the spl.. the only way i can do that i through bootloader and it flashes fine but when i then look in bootloader to see the spl it still shows 1.40 olinex..
Da9L said:
This does not work for me.. However i have a problem. the touch screen of my device is not working.. so i can't get pass the allign screen part .. and for somereason the ruu won't connect to phone when it is at tha part so i can't install the spl.. the only way i can do that i through bootloader and it flashes fine but when i then look in bootloader to see the spl it still shows 1.40 olinex..
Click to expand...
Click to collapse
You're right, I tried it too. Flashing SPL through bootloader doesn't work.
You can try using JumpSPL instead, I've attached it in this post. I don't think JumpSPL will require any screen prompts on your Diamond. You can read instructions.txt in the zip, but it's just really the .bat file so you get an idea of what it's doing. Run the .bat, press enter at the prompts and run the RUU for your stock SPL instead of HSPL when asked. At your own risk, I have not tried this myself.
where can i read more information about jumpspl, how it works and everything?
eranyanay said:
where can i read more information about jumpspl, how it works and everything?
Click to expand...
Click to collapse
Look in the Xda-wiki, search and google, and not just in the Diamond section.
sticky please
this needs to be a sticky topic.
losdrivare said:
You're right, I tried it too. Flashing SPL through bootloader doesn't work.
You can try using JumpSPL instead, I've attached it in this post. I don't think JumpSPL will require any screen prompts on your Diamond. You can read instructions.txt in the zip, but it's just really the .bat file so you get an idea of what it's doing. Run the .bat, press enter at the prompts and run the RUU for your stock SPL instead of HSPL when asked. At your own risk, I have not tried this myself.
Click to expand...
Click to collapse
I have just tried it and it gets stuck where it should run the JumpSPL.exe on the device. After a few minutes it comes with an error:
"ERROR: CreateProcess failed with Errorcode = 30123
- UNKNOWNERROR: 0x000075ab"
This is not good I just think its wierd that because of a broken screen it is impossible for me to get the stock spl flashed back on.
Da9L said:
I have just tried it and it gets stuck where it should run the JumpSPL.exe on the device. After a few minutes it comes with an error:
"ERROR: CreateProcess failed with Errorcode = 30123
- UNKNOWNERROR: 0x000075ab"
This is not good I just think its wierd that because of a broken screen it is impossible for me to get the stock spl flashed back on.
Click to expand...
Click to collapse
Sorry to hear it and I'm afraid I'm out of ideas. After all, my little tutorial is primarily aimed at those whose Diamonds have working screens...
On another note, my Diamond came back from warranty repair and the repair shop had not noticed anything that would void my warranty. In the meantime I got myself a Topaz and now I've sold my Diamond, but I'll be checking this thread from time to time.
Hey thanks bro..!! I need to give mine for reparing..
I have a hardware problem with the reset button.. Do you think I should flash my diamond back to stock? (I don't think they'll check the software right?)
donsalari said:
Hey thanks bro..!! I need to give mine for reparing..
I have a hardware problem with the reset button.. Do you think I should flash my diamond back to stock? (I don't think they'll check the software right?)
Click to expand...
Click to collapse
I would restore it to stock anyway. Some workshops actually look for excuses/reasons why the warranty won't apply so I say you'd definitly be taking a risk if you didn't.
losdrivare said:
I would restore it to stock anyway. Some workshops actually look for excuses/reasons why the warranty won't apply so I say you'd definitly be taking a risk if you didn't.
Click to expand...
Click to collapse
Very true!!! Ok cool... Flashing back to stock!!
Thanks..
Damn.. Hmm anyway then i will have to try the risk and sending it in with hardspl on it.. ! I Hope they won't see it.
Da9L said:
Damn.. Hmm anyway then i will have to try the risk and sending it in with hardspl on it.. ! I Hope they won't see it.
Click to expand...
Click to collapse
Another idea: maybe you can find some a VNC program that also works the "other way" with windows mobile, so that you can get a window on your PC with the screen of your device?
Hi. I'm an orange user and i dont know what SPL i should use to send back to warranty!
DOes anyone can recommend it please?
My Orange ROM is RUU_Diamond_HTC_WWE_1.93.405.1_Radio_Signed_Diamon d_52.29.25.12_1.00.25.05_Ship
UPDATE - i flashed the new rom and i tried to put the original SPL, however it still showing 1.40 Olinex in the bootloader and it still says security unlocked.
Any help please...
Hi I m singapore user i dont know what is the original spl 1.23 ??? i 4get leh can u tell me
bro i try 1.23.000 that version are u sure this is offical stockspl
as i remember it shld be SSPL not SPL somemore when running the tri-boot colour is diffferent from the offical 1
1 . Press volume up restore factory default bla bla bla ..
2 . Press volume down restore factory default and format the internal storage
3 . Press any button to cancel
Where is 2 n 3 ??? gone oridi
herpez said:
Hi. I'm an orange user and i dont know what SPL i should use to send back to warranty!
DOes anyone can recommend it please?
My Orange ROM is RUU_Diamond_HTC_WWE_1.93.405.1_Radio_Signed_Diamon d_52.29.25.12_1.00.25.05_Ship
UPDATE - i flashed the new rom and i tried to put the original SPL, however it still showing 1.40 Olinex in the bootloader and it still says security unlocked.
Any help please...
Click to expand...
Click to collapse
k3nnyboiboi said:
Hi I m singapore user i dont know what is the original spl 1.23 ??? i 4get leh can u tell me
Click to expand...
Click to collapse
If you manage to install ANY stock SPL and then flash the correct ROM for your country and operator then you automatically get the correct SPL too, since stock ROMs include SPL. If you go to htc.com and type in your s/n then you automatically get the latest ROM for your device and operator.
k3nnyboiboi said:
bro i try 1.23.000 that version are u sure this is offical stockspl
as i remember it shld be SSPL not SPL somemore when running the tri-boot colour is diffferent from the offical 1
1 . Press volume up restore factory default bla bla bla ..
2 . Press volume down restore factory default and format the internal storage
3 . Press any button to cancel
Where is 2 n 3 ??? gone oridi
Click to expand...
Click to collapse
I only link to the SPLs provided by olipro and cmonex in the hard-SPL thread. If you need closer info about SPLs I suggest you ask there. I only tried to revert back to stock SPL 1.93 myself and it worked just like described in first post.
Thanks Op
Managed to restore it no problem, but took ages

Categories

Resources