pls help - i can't flash my rom - 8525, TyTN, MDA Vario II, JasJam ROM Development

Dear bros,
Please help! i can't flash my rom to LVSW 20070507
my computer has installed zip and .Net2 already.
and i follow the instruction to upgrade, then it suddently said that i need to do recovery.
Then i also follow the steps and re-start my Hermes, it doesn't return to bootloader and reboot normally. Then i click skip on mu computer and then re-upgrade again, but the prcoess just repeats and repeats to ask me to do recovery.
Can anyone tell me which steps i have omitted????
my IPL - 1.01
SPL - 1.40 Olipro
Rom version - 3.22.200.4
Protocol version - 32.50.7018.00H
pls help me!
thanks in advance!

Read this : http://forum.xda-developers.com/showthread.php?t=299462

Sounds like you've made a brick - but probably recoverable... First we need more information...
1. Are you SuperCID?
2. Did your computer or phone crash or become disconnected during the original flash?
3. What error number is dosplayed when you try to flash?
4. When you boot the phone does it show NO GSM at the bottom right? (This may only display quickly so watch the boot process carefully), or does it show a radio ROM version such as 1.27.0.0?
5. Are you running Vista?
When you get this sort of info you need to move your question to the 'Dead Hermes....' thread. I'd also suggest reading a lot of it (even though it is long).
karay215 said:
Dear bros,
Please help! i can't flash my rom to LVSW 20070507
my computer has installed zip and .Net2 already.
and i follow the instruction to upgrade, then it suddently said that i need to do recovery.
Then i also follow the steps and re-start my Hermes, it doesn't return to bootloader and reboot normally. Then i click skip on mu computer and then re-upgrade again, but the prcoess just repeats and repeats to ask me to do recovery.
Can anyone tell me which steps i have omitted????
my IPL - 1.01
SPL - 1.40 Olipro
Rom version - 3.22.200.4
Protocol version - 32.50.7018.00H
pls help me!
thanks in advance!
Click to expand...
Click to collapse

ach2 said:
Sounds like you've made a brick - but probably recoverable... First we need more information...
1. Are you SuperCID?
YES, I am superCID
2. Did your computer or phone crash or become disconnected during the original flash?
No
3. What error number is dosplayed when you try to flash?
it's ERROR 302, update error
4. When you boot the phone does it show NO GSM at the bottom right?
nth happened, just a normal reboot and the phone is just as normal as before
(This may only display quickly so watch the boot process carefully), or does it show a radio ROM version such as 1.27.0.0?
5. Are you running Vista?
No, i am running WIN XP Sp2
When you get this sort of info you need to move your question to the 'Dead Hermes....' thread. I'd also suggest reading a lot of it (even though it is long).
Click to expand...
Click to collapse
AND i have read the above link so many times and i have followed all the steps, but don't know what happened....
pls help!
thanks!!!

karay215 said:
AND i have read the above link so many times and i have followed all the steps, but don't know what happened....
pls help!
thanks!!!
Click to expand...
Click to collapse
Answer the questions then, don't just skip by them hoping by some miracle someone will know what your PDA is suffering from and give you the answer. What guide did you follow?

Fix from LegolastheElf​
1.40.oli has a bug (because the original BL it was based on had a bug)...
You need to upgrade to Hardspl 2.10, then flash LVSW.
hope it works for you

Even though this beginner submitted a really vague problem, it was resolved without insults. Hooray!

man, my thoughts exactly!

thanks bro~!
but i even can't flash to Hard SPL v.7
the problem is the same....
it asks me to recover again and again.....

karay215 said:
thanks bro~!
but i even can't flash to Hard SPL v.7
the problem is the same....
it asks me to recover again and again.....
Click to expand...
Click to collapse
you need to put the (HardSPL) nbh on your sd card as HERMIMG.nbh and then execute sspl on your device, it should upgrade to HardSPL then

Related

My First Brick..... :eek:

Hi guys. I have installed loads of ROMs onto my trusty hermes yet today, when trying to flash DuttyThroys Ultra Ultra Lite rom this happened: i downloaded ROM and installed it, it seemed to install fine, got to 100% and then came up with error message stating that Image File was corrupt. Now my hermes is stuck on the multicoloured bootloader screen?!?!?!? I have SPL 2.10. Hard SPL V7 HERM 100 IPL 1.04 (Dont know which of these is relevant to anythin?) .I have read the WIKI on repairing bricks but for my problem it says to reflash any nbh without radio. How is this possible if i cant get my pc to connect to my hermes???
Tried the method of turning off usb connection in active sync, removing battery, reconnecting to usb and running mitty (command SET 14 0) but nothing happens. Mitty says CMD error and active sync doesnt reopen the connection like the guide says! Man i hate this cuz i have now become one of those annoying noobs who has bricked their phone and hassles everyone for help!!!!
Have also tried to flash from sd card but nothing happens, flicks to white screen with LOADING... on it for 2 secons then flicks back to that wonderful multicoloured screen of joy!
Any help will be appreciated guys, cant live without my hermes!!!
Welcome to the fuc... nightmare world of the brick,i'mma in your same situation,now my Tytn is a piece of white stone,and it seems there's no reason to bring it back to live!
I can't stay without my Tytn i do a lot of things with it,Skype,SIP calls,Mail,Messenger,Memo,Internet......i'm in totally despair!!!
you should be able to just reflash a known good rom.
hfam95 said:
you should be able to just reflash a known good rom.
Click to expand...
Click to collapse
Brilliant story! both compelling and rich. But i have already explained that my pc doesnt recognise my hermes so how do you RECOMMEND i flash??
IT could be interesting to make the minimal effort to go and read the wiki.
anyway:
http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
Better than just cry.
MarcWhittle said:
Brilliant story! both compelling and rich. But i have already explained that my pc doesnt recognise my hermes so how do you RECOMMEND i flash??
Click to expand...
Click to collapse
With the microsd card...
right, its looking good. managed to begin flashing (bar has stopped for ages but having read this is normal im not so scared!) using the SD method. Where my device wasnt superCID i had to use the matching ROM (Orange) to my CID (which incidently i dont know, just downloaded both Orange ROMs).
While im waiting ill try and help you TETSUO! (Im a noob so probably cant!)
Is your device SuperCID??? tell me as much as you can about your device SPL etc
dude, if u read my post u would have seen that i have tried SD method once (sing Black 3.5 not ORANGE ROM), im not crying and im grateful for any help but when i get advice such as 'flash a rom' im gonna be pissed!
And i have read ALL the page on unbricking!!!
It worked!!
One more question, as i have installed a stock Orange ROM do i now need to reinstall HardSPL v7??
Are you on a Win XP or a Vista PC?
XP dude, sorry should have said! and thanks
i went into bootloader, still says 2.10 olipro but when i try to update to new ROM (Black X RC)and pick autodetect it says it says unknown version, use SSPL. it never used to say this so i assume i need to install HardSPL 7 again???
with the tri colour sceen, when you plug the usb cable in does it go from serial to USB ?
what OS have you got ?
just my 2 cents hope it helps.
dude, i have got past that problem and have managed to install an Orange ROM onto it. i only need to know ow whether to install HardSPL v7 again!
sorry slooooooooooooooooow typing
good question hope there an answer,
MarcWhittle said:
dude, i have got past that problem and have managed to install an Orange ROM onto it. i only need to know ow whether to install HardSPL v7 again!
Click to expand...
Click to collapse
just saw your post if ur device is hardspl you just need to supercid your device, If your spl is still showing hardspl and its coming as a error that normally happens to me as well just manually click spl 2.10 and tick (is it hardspl?}
To recap, i have now managed to flash a stock Orange ROM from SD card ( i think the reason it didnt work first time with SD is because device isnt SuperCID and i was trying to flash Black RC, soon as i used Orange ROM (my device is M3100) it worked. I am now back to a fully operational device. I wish to go back to Black but when i AutoDetect what bootloader i have it recommeds SSPL method. Before all my problems it would always automatically pick 2.10?? Does this mean i need to install HardSPL v7 again??
it was HardSPL v7 before all these problems, but im a noob so dont know if it still is?? would installing Orange ROM from SD Card remove HardSPL?? Bootloader still shows SPL as 2.10 oli
MarcWhittle said:
it was HardSPL v7 before all these problems, but im a noob so dont know if it still is?? would installing Orange ROM from SD Card remove HardSPL?? Bootloader still shows SPL as 2.10 oli
Click to expand...
Click to collapse
If you only flash the orange os.nb only then your hardspl wouldnt have changed so its safe to flash your device just manually choose.
If you want to flash hardspl again then do it on a precaution method
Mark,
First of all well done for getting yourself out of a hole. It seems quite difficult to ask for help these days without being shot to pieces even when you have first tried to help yourself by doing all the right things, which is more than can be said for some who come on here asking for help. So well done again.
Re your question, I would reflash Hard SPL anyway to be sure; however before you do that go to the Mr Vanx's guide on hard SPL (forgot the link but type in www.mrvanx.org and you should be taken there) and follow his instructions.
Good luck.
WB

Urgent! My diamond has hardware problem and need to fallback to stock ROM and SPL.

Hi,
My Diamond has no response on the screen, so I think I need to return to factory for repairing. However I have difficulties in falling back to stock ROM and SPL.
From the Wiki:
---------------
STEP BY STEP HOW TO RETURN TO STOCK SPL - FOR WARRANTY REASONS ONLY!
0. be sure to first restore stock OS, and stock radio. stock SPL is always to be done last!!
...
-----------------
I can't flash my ROM to latest HK WWE CSL ROM (2.03) as it just stopped at 0%. I'm using SPL-1.30.OliNex.
Questions:
0) Why? Any step I've missed? I've just copied the .NBH from HTC official ROM download. Should I get the .NBH from the Wiki instead?
1) Should I flash to v1.93 (the very beginning of the ROM)?
2) Must the RADIO be flashed back as well? or the above Stock ROM has included the RADIO already?
3) Anyone can give me a reference on the step-by-step in details...
Thanks!
Please help...
F810
Questions:
f810 said:
0) Why? Any step I've missed? I've just copied the .NBH from HTC official ROM download. Should I get the .NBH from the Wiki instead?
Click to expand...
Click to collapse
If the latest was the offical from the site then you could use that - as you are having issues flashing this with 1.30 HSPL, I would suggest updating that to 1.40
f810 said:
1) Should I flash to v1.93 (the very beginning of the ROM)?
Click to expand...
Click to collapse
This might be a easier option and should work woth the 1.30 HSPL
f810 said:
2) Must the RADIO be flashed back as well? or the above Stock ROM has included the RADIO already?
Click to expand...
Click to collapse
This is recommended
f810 said:
3) Anyone can give me a reference on the step-by-step in details...
Click to expand...
Click to collapse
Its really straight forward like the WiKi suggests
This Thread may help
Thanks a lot.
Re Q3, so do you mean if I extracted the stock NBH, it's only OS but not including RADIO? If so, I will get the RADIO from wiki page later. Would you please clarify for me?
After your information, I think the steps in Wiki are clear. Thanks.
If this is HK ROM is the one you have downloaded from HTC PAGE then it has a radio included
Since my Diamond is totally malfunction in the touch screen, I can't response to all the confirmation & prompts...
I've failed to install Stock ROM and tried your recommendation on upgrading to HSPL 1.40. There was a confirmation on running the program in my Diamond and I can't press YES and now my diamond is just like bricked.
I've also tried pressing VOL DOWN + Reset to connect the Diamond via USB. The ROM Update Utility has "successfully" update the HSPL, but actually when I hard reset it and found it's still running 1.30... Can I just use this approach to fallback to Factory status??
Anyone has good idea on how to fallback to Factory Stock ROM, RADIO and SPL, provided that my screen has totally no response to me?
PLEASE...PLEASE...PLEASE help.
You will not be able to update olipros Hard SPL in bootloader mode as the SPL is protected and the 1.30 will prevent this although show its been done.
What you will need to do then is just load a 1.93 ROM from boot loader. the were some in that link i posted earlier. as to reverting to the default SPL - you may be luck not to need the screen for any confirmation. but running a new SPL to overwrite Oli's you will need to use windows and the RRU
I've tried to load 1.93 ROM to my diamond but failed on OliNex 1.30. The link in modmydiamond.info on OliNex 1.40 Signed seems not correct, as it's still 1.30 after flashed. I've then flashed UNSIGNED 1.40 OliNex SPL (also downloaded from modmydiamond.info) and now flashing the 1.93 ROM in progress from bootloader.
I will flash the Stock SPL through the Bootloader after that...I hope I can successfully fallback and get it repair...
Last question (I hope), the stock SPL should be 1.37 so I want to confirm whether it can boot 1.93 ROM.
Thanks a lot!
Because these Unsigned HARD SPL 's are write protected.....you will fail all the time. Not sure if stock SPL can undue the write protection but if you still get stuck after you try then in order to bypass write protection I know Jump SPL allows for this.
band27 said:
Because these Unsigned HARD SPL 's are write protected.....you will fail all the time. Not sure if stock SPL can undue the write protection but if you still get stuck after you try then in order to bypass write protection I know Jump SPL allows for this.
Click to expand...
Click to collapse
you're right. When I flash the Stock SPL, it is "successful" but actually it doesn't update the SPL (i.e yet running OliNex 1.40). Where can I get the Jump SPL?
Here you go....I did a search
Hi,
Sorry to use this thread but im also trying to install back to my original Diamond ROM and am currently using the rom developed by Diamond Project (1.93.456.2WWE) and i kept flashing it back using Signed V1.93 RUU and apprently the Diamond project words still keep showing out when i start my phone!
How do i completely remove the Diamond Project thing? Thank you!
Read this............Scroll to Post #39
http://forum.xda-developers.com/showthread.php?t=400950&page=4
band27 said:
Here you go....I did a search
Click to expand...
Click to collapse
I also got that but it's not win32 program... I believe it's running on the Diamond. But I've hard reset, and never able to setup as it's screen was not functioning now...
kawatsu said:
Hi,
Sorry to use this thread but im also trying to install back to my original Diamond ROM and am currently using the rom developed by Diamond Project (1.93.456.2WWE) and i kept flashing it back using Signed V1.93 RUU and apprently the Diamond project words still keep showing out when i start my phone!
How do i completely remove the Diamond Project thing? Thank you!
Click to expand...
Click to collapse
That ROM had a different boot image - so you need to replace that by flashing another splash .NBH file using RUU.
Original splash can be found HERE
and if needed CUSTOM RUU HERE
Just un-zip these and put the splash file in the same folder as the Custom RUU and run the RUU - the flash should take a few seconds and viola - bye bye Diamond project splash.
f810 said:
I've tried to load 1.93 ROM to my diamond but failed on OliNex 1.30. The link in modmydiamond.info on OliNex 1.40 Signed seems not correct, as it's still 1.30 after flashed. I've then flashed UNSIGNED 1.40 OliNex SPL (also downloaded from modmydiamond.info) and now flashing the 1.93 ROM in progress from bootloader.
I will flash the Stock SPL through the Bootloader after that...I hope I can successfully fallback and get it repair...
Last question (I hope), the stock SPL should be 1.37 so I want to confirm whether it can boot 1.93 ROM.
Thanks a lot!
Click to expand...
Click to collapse
I think as long as the SPL is changed and the ROM is of the original language the I think it should be OK to send back like that
f810 said:
you're right. When I flash the Stock SPL, it is "successful" but actually it doesn't update the SPL (i.e yet running OliNex 1.40). Where can I get the Jump SPL?
Click to expand...
Click to collapse
As said before; you should be able to successfully run the stock SPL using RUU - if you are trying this via bootloader it will not work.
Which is the original SPL?? 1.23, 1.34 or 1.37? I do recall taking a picture of the original SPL when i 1st got the Diamond for days like that but i just can't find it now
I'm bought it from Malaysia. Anybody can help me confirm this??
R3PUBL1K said:
As said before; you should be able to successfully run the stock SPL using RUU - if you are trying this via bootloader it will not work.
Click to expand...
Click to collapse
I've tried to connect to ActiveSync successfully although the Initial Setup wizard on my Diamond. I've then run the RUU from RUU-SSPL-withoutNBH.zip and put the stock SPL .NBH file into the extracted directory. It can retrieve my device info, and when I confirm the update of ROM, after 3-5 sec it said about connection failure. I can browse the Internal Storage at the moment yet.
I've then tried similar thing using the Custom RUU inside the package diamond-hspl-1.34.zip. This time I can see 100% update. When I press VolDown and reset, the SPL is still v1.40 ONliEx.
What's wrong with my procedures above?
f810 said:
I've tried to connect to ActiveSync successfully although the Initial Setup wizard on my Diamond. I've then run the RUU from RUU-SSPL-withoutNBH.zip and put the stock SPL .NBH file into the extracted directory. It can retrieve my device info, and when I confirm the update of ROM, after 3-5 sec it said about connection failure. I can browse the Internal Storage at the moment yet.
I've then tried similar thing using the Custom RUU inside the package diamond-hspl-1.34.zip. This time I can see 100% update. When I press VolDown and reset, the SPL is still v1.40 ONliEx.
What's wrong with my procedures above?
Click to expand...
Click to collapse
I think I miss the step of running the SSPL-Manual.exe because of my screen is not responding... Anyway for me to put it into the Windows Startup Folder?? When I use ActiveSync I can't see Windows directory.
Please...please...I miss this step only...
f810 said:
I think I miss the step of running the SSPL-Manual.exe because of my screen is not responding... Anyway for me to put it into the Windows Startup Folder?? When I use ActiveSync I can't see Windows directory.
Please...please...I miss this step only...
Click to expand...
Click to collapse
Can anyone help??

flash T-mobile rom to Touch Diamond ROM's

I have a t-mobile MDA IV(HTC Touch Diamond) and want to upgrade to other Rom's but without succes.
Rom-versie: 1.37.114.3 NLD
Radio 1.00.25.03
what do i have to do so i can use other rom's?
DO I have to unlock CID lock firts and if yes i can not find the program to unlick it.
Please help me I am a starting hobby'st for touch diamond.
thank you.
Dont be afraid of research
read the upgrading guide here in the diamond forum it will answer all of ur questions. We all begin some where at the bottom!
cihan said:
I have a t-mobile MDA IV(HTC Touch Diamond) and want to upgrade to other Rom's but without succes.
Rom-versie: 1.37.114.3 NLD
Radio 1.00.25.03
what do i have to do so i can use other rom's?
DO I have to unlock CID lock firts and if yes i can not find the program to unlick it.
Please help me I am a starting hobby'st for touch diamond.
thank you.
Click to expand...
Click to collapse
What I did was to flash to a stock HTC ROM first them, went from there!
Ankleman said:
What I did was to flash to a stock HTC ROM first them, went from there!
Click to expand...
Click to collapse
can you tell me witch rom you flashe with?
kwambewright said:
read the upgrading guide here in the diamond forum it will answer all of ur questions. We all begin some where at the bottom!
Click to expand...
Click to collapse
I hace tried like it's described in the manual and no succes, it stucks at 0%:
that was the reason to sk for help!
A. Upgrading to HardSPL (Bible page)
There are several HardSPL editions available for the Diamond. While I have decided to go with the HardSPL described in this guide, the majority of Chefs indicate clearly in the ROM thread what version of HardSPL is recommended to go with their cooked ROM.
IMPORTANT!
Make sure you have the prerequisites!
1. Download OliNex Unsigned Hard-SPL (Developers Edition) from here;
2. Unzip the files from the archive to any new folder;
3. Run the executable (in most cases it is ROMUpdateUtility.exe, but it also can be ROM.exe or any other name, recognize it by the icon);
4. If you understand the caution and risks, check the box and click Next;
5. Read carefully and follow all directions;
6. If you completed all steps indicated, check the box and click Next;
7. Next screen will show current version on device and by clicking Update you will see the version to be flashed;
8. Click Next when ready;
9. Your device might ask you for confirmation on launching a program. Just tap Yes! Your device will display a completely black screen. A Progress bar will appear on your computer screen. Be patient while your device is being updated. Do not interact with device in any way, do not unplug cable, do not turn off device or computer!
10. When upgrading is finished, your device will automatically soft reset. Click the ‘Finish’ button to exit the RUU.
To verify if you indeed have correct HardSPL on your device, enter Bootloader by pushing the reset button while holding volume down key on the side.
It should display*:
* In case of another HardSPL, the version number would differ!

[TUT] HOW-TO restore Diamond to stock for warranty

Due to a hardware problem in my Diamond I needed to restore it to manufacturer default. I didn't find a guide to this and since I've done the research anyway I thought I'd put together this little tutorial as the information was somewhat scattered around the forum. I hope this guide will be of use for the community.
My phone was originally branded and sim-locked by 3. After I was through with it, it was SIM-unlocked, security unlocked and had HSPL, custom ROM and a radio ported from another device. The steps below is what I did to restore it to stock. All steps might not be neccessary for you. This procedure might also work for other devices than the Diamond, but of course you need other versions of SPL, ROM etc.
1. Backup everything on your phone to your computer - use activesync, PIMbackup etc and make a copy of your Internal Storage.
2. Make a hard reset (hold vol down + enter and soft reset) and chose to format moviNAND. This step is only neccessary if you want to wipe your Internal Storage before you send the device in for repair, but I recommend it.
3. Go to www.htc.com and download the latest stock ROM (includes stock radio and SPL). You find it under Support and you enter your s/n to get the correct stock ROM for your device, complete with branding for your operator. You can also find stock ROMS here: http://forum.xda-developers.com/showthread.php?t=471699
4. Flash the stock ROM. Now you have stock ROM and Radio on your device. Stock SPL will not be installed until you've replaced HSPL with an older stock SPL and flashed ROM again.
5. Get RUU-SSPL and stock SPL from HERE:
http://forum.xda-developers.com/showpost.php?p=2324829&postcount=39. I used the stock 1.93 SPL. Some instructions and info about restoring stock SPL is in the linked post by cmonex and due credit goes to her. I will repeat some of that info to keep this guide step-by-step. EDIT: Stock SPL 2.03 can be found here: http://forum.xda-developers.com/showpost.php?p=3359191&postcount=390
6. Put the .nbh file from the SPL you downloaded into the same folder as the extracted contents of RUU-SSPL-withoutNBH.zip and run the RUU. This flashes an old stock SPL.
7. Flash your stock ROM from step 3 again. This step is neccessary to get the correct stock SPL on your device, eg. the one that corresponds with the stock ROM you've downloaded in step 3. It was not installed in step 4, because then you still had HSPL. In step 6 you've installed a stock SPL and now the correct stock SPL will flash along with the stock ROM. After this step I got SPL 2.03 on my Diamond.
8. Remove the Security Unlock from your device using the instructions and Security Relocker by Olinex from this post by cmonex: http://forum.xda-developers.com/showpost.php?p=3299516&postcount=492
Now, my Diamond is still SIM-unlocked. I have not managed to find any info about how to restore the SIM-lock, but it is hopefully not neccessary for warranty. As far as I can tell, the unlock doesn't show anywhere, but of course all they need to do is to try a SIM-card from another operator...
If anyone has info about how to restore SIM-lock, then I'll update this guide with that info.
good job...
moderator make this "sticky"
3dward87 said:
good job...
moderator make this "sticky"
Click to expand...
Click to collapse
I second that, it contains links to stock ROMs, that'll hopefully stop a million topics about it lol.
This does not work for me.. However i have a problem. the touch screen of my device is not working.. so i can't get pass the allign screen part .. and for somereason the ruu won't connect to phone when it is at tha part so i can't install the spl.. the only way i can do that i through bootloader and it flashes fine but when i then look in bootloader to see the spl it still shows 1.40 olinex..
Da9L said:
This does not work for me.. However i have a problem. the touch screen of my device is not working.. so i can't get pass the allign screen part .. and for somereason the ruu won't connect to phone when it is at tha part so i can't install the spl.. the only way i can do that i through bootloader and it flashes fine but when i then look in bootloader to see the spl it still shows 1.40 olinex..
Click to expand...
Click to collapse
You're right, I tried it too. Flashing SPL through bootloader doesn't work.
You can try using JumpSPL instead, I've attached it in this post. I don't think JumpSPL will require any screen prompts on your Diamond. You can read instructions.txt in the zip, but it's just really the .bat file so you get an idea of what it's doing. Run the .bat, press enter at the prompts and run the RUU for your stock SPL instead of HSPL when asked. At your own risk, I have not tried this myself.
where can i read more information about jumpspl, how it works and everything?
eranyanay said:
where can i read more information about jumpspl, how it works and everything?
Click to expand...
Click to collapse
Look in the Xda-wiki, search and google, and not just in the Diamond section.
sticky please
this needs to be a sticky topic.
losdrivare said:
You're right, I tried it too. Flashing SPL through bootloader doesn't work.
You can try using JumpSPL instead, I've attached it in this post. I don't think JumpSPL will require any screen prompts on your Diamond. You can read instructions.txt in the zip, but it's just really the .bat file so you get an idea of what it's doing. Run the .bat, press enter at the prompts and run the RUU for your stock SPL instead of HSPL when asked. At your own risk, I have not tried this myself.
Click to expand...
Click to collapse
I have just tried it and it gets stuck where it should run the JumpSPL.exe on the device. After a few minutes it comes with an error:
"ERROR: CreateProcess failed with Errorcode = 30123
- UNKNOWNERROR: 0x000075ab"
This is not good I just think its wierd that because of a broken screen it is impossible for me to get the stock spl flashed back on.
Da9L said:
I have just tried it and it gets stuck where it should run the JumpSPL.exe on the device. After a few minutes it comes with an error:
"ERROR: CreateProcess failed with Errorcode = 30123
- UNKNOWNERROR: 0x000075ab"
This is not good I just think its wierd that because of a broken screen it is impossible for me to get the stock spl flashed back on.
Click to expand...
Click to collapse
Sorry to hear it and I'm afraid I'm out of ideas. After all, my little tutorial is primarily aimed at those whose Diamonds have working screens...
On another note, my Diamond came back from warranty repair and the repair shop had not noticed anything that would void my warranty. In the meantime I got myself a Topaz and now I've sold my Diamond, but I'll be checking this thread from time to time.
Hey thanks bro..!! I need to give mine for reparing..
I have a hardware problem with the reset button.. Do you think I should flash my diamond back to stock? (I don't think they'll check the software right?)
donsalari said:
Hey thanks bro..!! I need to give mine for reparing..
I have a hardware problem with the reset button.. Do you think I should flash my diamond back to stock? (I don't think they'll check the software right?)
Click to expand...
Click to collapse
I would restore it to stock anyway. Some workshops actually look for excuses/reasons why the warranty won't apply so I say you'd definitly be taking a risk if you didn't.
losdrivare said:
I would restore it to stock anyway. Some workshops actually look for excuses/reasons why the warranty won't apply so I say you'd definitly be taking a risk if you didn't.
Click to expand...
Click to collapse
Very true!!! Ok cool... Flashing back to stock!!
Thanks..
Damn.. Hmm anyway then i will have to try the risk and sending it in with hardspl on it.. ! I Hope they won't see it.
Da9L said:
Damn.. Hmm anyway then i will have to try the risk and sending it in with hardspl on it.. ! I Hope they won't see it.
Click to expand...
Click to collapse
Another idea: maybe you can find some a VNC program that also works the "other way" with windows mobile, so that you can get a window on your PC with the screen of your device?
Hi. I'm an orange user and i dont know what SPL i should use to send back to warranty!
DOes anyone can recommend it please?
My Orange ROM is RUU_Diamond_HTC_WWE_1.93.405.1_Radio_Signed_Diamon d_52.29.25.12_1.00.25.05_Ship
UPDATE - i flashed the new rom and i tried to put the original SPL, however it still showing 1.40 Olinex in the bootloader and it still says security unlocked.
Any help please...
Hi I m singapore user i dont know what is the original spl 1.23 ??? i 4get leh can u tell me
bro i try 1.23.000 that version are u sure this is offical stockspl
as i remember it shld be SSPL not SPL somemore when running the tri-boot colour is diffferent from the offical 1
1 . Press volume up restore factory default bla bla bla ..
2 . Press volume down restore factory default and format the internal storage
3 . Press any button to cancel
Where is 2 n 3 ??? gone oridi
herpez said:
Hi. I'm an orange user and i dont know what SPL i should use to send back to warranty!
DOes anyone can recommend it please?
My Orange ROM is RUU_Diamond_HTC_WWE_1.93.405.1_Radio_Signed_Diamon d_52.29.25.12_1.00.25.05_Ship
UPDATE - i flashed the new rom and i tried to put the original SPL, however it still showing 1.40 Olinex in the bootloader and it still says security unlocked.
Any help please...
Click to expand...
Click to collapse
k3nnyboiboi said:
Hi I m singapore user i dont know what is the original spl 1.23 ??? i 4get leh can u tell me
Click to expand...
Click to collapse
If you manage to install ANY stock SPL and then flash the correct ROM for your country and operator then you automatically get the correct SPL too, since stock ROMs include SPL. If you go to htc.com and type in your s/n then you automatically get the latest ROM for your device and operator.
k3nnyboiboi said:
bro i try 1.23.000 that version are u sure this is offical stockspl
as i remember it shld be SSPL not SPL somemore when running the tri-boot colour is diffferent from the offical 1
1 . Press volume up restore factory default bla bla bla ..
2 . Press volume down restore factory default and format the internal storage
3 . Press any button to cancel
Where is 2 n 3 ??? gone oridi
Click to expand...
Click to collapse
I only link to the SPLs provided by olipro and cmonex in the hard-SPL thread. If you need closer info about SPLs I suggest you ask there. I only tried to revert back to stock SPL 1.93 myself and it worked just like described in first post.
Thanks Op
Managed to restore it no problem, but took ages

How do I bring back my Desire to work?

Hi
I´m in trouble with my Desire and need professional help.
It´s a (was a?) 093.0001 with root and s-off
I´ve installed Leedroid V3.07 (Gingerbread) incl. Custom HBoot for data++ and the Radio 32.56.00.32U_5.17.05.08
I´ve tried to flash it back to original by using the orig. 2.2 Stock Rom from HTC. As far as I know should this be enough to bring it back to original.
Now there is the following problem:
The update breaks with the message, I´ve got to use an other RUU. The phone hangs with a black screen and triangles in it.
I can not start it in BL mode. It hangs with a partition failure.
Is this a fullbrick or is there a way to fix it? Does the radio make this problems? How can i create a higher radio number to overflash it?
What woulda real specialist do now?
Thanks for help...
[email protected] said:
Hi
I´m in trouble with my Desire and need professional help.
It´s a (was a?) 093.0001 with root and s-off
I´ve installed Leedroid V3.07 (Gingerbread) incl. Custom HBoot for data++ and the Radio 32.56.00.32U_5.17.05.08
I´ve tried to flash it back to original by using the orig. 2.2 Stock Rom from HTC. As far as I know should this be enough to bring it back to original.
Now there is the following problem:
The update breaks with the message, I´ve got to use an other RUU. The phone hangs with a black screen and triangles in it.
I can not start it in BL mode. It hangs with a partition failure.
http://forum.xda-developers.com/showthread.php?t=695
Is this a fullbrick or is there a way to fix it? Does the radio make this problems? How can i create a higher radio number to overflash it?
What woulda real specialist do now?
Thanks for help...
Click to expand...
Click to collapse
Hi Patrick,
This happens usually with branded phones. In this thread you'll have to find the appropriate RUU, the RUU designed for your phone's original carrier. Did you make a goldcard ?
No, I did not make a goldcard.
I thought, Goldcard is not longer needed, so I dind´t make one...
But I´m a step closer (or did I make a sep back?)
I had acces via fastboot and tried to flash an other stock ROM via fastbootcommander...
Now I have the old HBOOT 0.93.0001 and my old radio. I´n not root anymore, and s-on is now printed in the display - but the flash stops with an partition failure again...
Is the partition failure the point to search for branded roms?
[email protected] said:
No, I did not make a goldcard.
I thought, Goldcard is not longer needed, so I dind´t make one...
But I´m a step closer (or did I make a sep back?)
I had acces via fastboot and tried to flash an other stock ROM via fastbootcommander...
Now I have the old HBOOT 0.93.0001 and my old radio. I´n not root anymore, and s-on is now printed in the display - but the flash stops with an partition failure again...
Is the partition failure the point to search for branded roms?
Click to expand...
Click to collapse
Do you have any idea if your phone is branded ?
No, I have no idea... bevore I start rooting i did not have seen any signs for a branding.
Mostly the desire shows an own startlogo from the carrier, isn´t it?
My problem is, the update is starting, but it aborts at ~50% with this failure...
All other updates won´t start, just this one RUU goes up to 50 percent...
[email protected] said:
No, I have no idea... bevore I start rooting i did not have seen any signs for a branding.
Mostly the desire shows an own startlogo from the carrier, isn´t it?
Click to expand...
Click to collapse
I didn't see any ROM for a German provider. Which RUU did you try to flash ?
paul.c said:
I didn't see any ROM for a German provider. Which RUU did you try to flash ?
Click to expand...
Click to collapse
I try this one:
RUU_Bravo_Froyo_HTC_WWE_2.29.405.5_Radio_32.49.00.32U_5.11.05.27_release_159811_signed
Is there a way to dump a firmware from a running desire?
[email protected] said:
I try this one:
RUU_Bravo_Froyo_HTC_WWE_2.29.405.5_Radio_32.49.00.32U_5.11.05.27_release_159811_signed
Is there a way to dump a firmware from a running desire?
Click to expand...
Click to collapse
I see. How does the error sound exactly ?
Maybe this RUU would help: http://shipped-roms.com/download.ph...io_32.30.00.28U_4.05.00.11_release_121684.exe
Edit: check this out: http://oxygenrom.com/viewtopic.php?f=5&t=190
Edit: this is a slightly older WWE RUU: http://shipped-roms.com/download.ph...9.00.32U_5.11.05.27_release_151783_signed.exe
this rom does nor work for me... I tried it a few times theis night...
The Error sounds [Error 131] - This Rom Update Utility can not update this Android Phone - Get the right ROM Update Utility Program and try again.
Sorry, I´m not very good in translating things, but Error 131 is the Problem for now...
Bevore this it told me there was a partition failure (step 6)...
[email protected] said:
this rom does nor work for me... I tried it a few times theis night...
The Error sounds [Error 131] - This Rom Update Utility can not update this Android Phone - Get the right ROM Update Utility Program and try again.
Sorry, I´m not very good in translating things, but Error 131 is the Problem for now...
Bevore this it told me there was a partition failure (step 6)...
Click to expand...
Click to collapse
Have you installed HTC Sync and drivers ?
I have installed the correct drivers, HTC Sync is not installed anymore...
I wonder that I have no access to my bootloader, just this black screen. But if I pull off the cable from my desire, i have the white bootloader screen, just without any entrys...
[email protected] said:
I have installed the correct drivers, HTC Sync is not installed anymore...
I wonder that I have no access to my bootloader, just this black screen. But if I pull off the cable from my desire, i have the white bootloader screen, just without any entrys...
Click to expand...
Click to collapse
You need HTC Sync. Start your phone in fastboot (back button + power), connect you phone and run RUU.
I´ve tried it a serval times, as admin, without admin rights, various combinations of rights and versions and have everytime the same problem...
I cann not see the phone starting in fastboot, even if I try to boot, the phone hangs with this black pic...
If I disconnect the cable from the phone I see the white page, but the last Entry is ruu, nothing more... there is nothing I can navigate to.
[email protected] said:
I´ve tried it a serval times, as admin, without admin rights, various combinations of rights and versions and have everytime the same problem...
I cann not see the phone starting in fastboot, even if I try to boot, the phone hangs with this black pic...
If I disconnect the cable from the phone I see the white page, but the last Entry is ruu, nothing more... there is nothing I can navigate to.
Click to expand...
Click to collapse
Try this: http://forum.xda-developers.com/showthread.php?t=921398&highlight=create+goldcard
Hey [email protected] . . 1st check if your pc is recognising your phone.
Connect to pc and check in device manager what is it showing.. should be adb or bootloader interface.. if not try to install adb driver...
than once its done.
try to run this RUU
http://shipped-roms.com/download.ph...9.00.32U_5.11.05.27_release_151783_signed.exe
basically error 131 is for CID.. so you will require a goldcard for that.. just try your luck .. remove both memory card and simcard.. and run the RUU..
Let us know the results
Allright everybody - It works! Feels like birthday @ christmas together, including a final blowjob and a cold beer togeter
What did I do? I´ve created a new goldcard on a second desire, used this card and started the final RUU again - That was all... Little think, big Impression
I thought all the time, the goldcard was specific for the telephone, but it was specially for the memory card.
Thanks a lot for all of your help! I know, there were many help for this stupid guy
But you all have saved the live of my desire... Thanks
[email protected] said:
Allright everybody - It works! Feels like birthday @ christmas together, including a final blowjob and a cold beer togeter
What did I do? I´ve created a new goldcard on a second desire, used this card and started the final RUU again - That was all... Little think, big Impression
I thought all the time, the goldcard was specific for the telephone, but it was specially for the memory card.
Thanks a lot for all of your help! I know, there were many help for this stupid guy
But you all have saved the live of my desire... Thanks
Click to expand...
Click to collapse
I'm glad for you. This is how you learn, stupidity has nothing to do with it.
paul.c said:
I'm glad for you. This is how you learn, stupidity has nothing to do with it.
Click to expand...
Click to collapse
Yes, you´re right... I´ve tryes a lot, I´ve learned even more tonight...
OK, second shot - I´m going to root & s-off my phone again...
[email protected] said:
Yes, you´re right... I´ve tryes a lot, I´ve learned even more tonight...
OK, second shot - I´m going to root & s-off my phone again...
Click to expand...
Click to collapse
Don't forget your glodcard. Keep it safe.

Categories

Resources