Related
Hallo everbody.
I'd really be glad, if you could help my with my problem:
I currently have bepe's german WM6 ROM v. 0.5 installed on my P3600. Now, the problem is, that I cannot flash anything anymore. When I start any rom update, the device enters boot loader, the progress bar gradually counts to 100% (a little faster, than I remember it doing before). At 100% the device turns off, but doesn't reboot itself. The rom update utility reports a success. When I then restart the device, everything is as before, without any changes.
My installed Hard SPL is SPL-9.99.CP. I tried to flash Olipro's new SPL without any luck. The SPL remains SPL-9.99.CP.
I don't know what to do any more...
have you installed Hard SPL by Oli 1.30????
if yes, downgrade to 1.20 version
psxsnake said:
have you installed Hard SPL by Oli 1.30????
if yes, downgrade to 1.20 version
Click to expand...
Click to collapse
Problem is, I have SPL-9.99.CP installed. It seems, that I even cannot flash to another SPL any more. I just tried to flash Oli 1.30 without any luck.
paranoid2007 said:
Problem is, I have SPL-9.99.CP installed. It seems, that I even cannot flash to another SPL any more. I just tried to flash Oli 1.30 without any luck.
Click to expand...
Click to collapse
SPL 9.99.CP will show with all HARD-SPLs I believe. Try to Flash HARD SPL 1.2 - and then try flashing again.
Lots of people could not flash anything with HARD SPL 1.3 flashed.
nealed said:
SPL 9.99.CP will show with all HARD-SPLs I believe. Try to Flash HARD SPL 1.2 - and then try flashing again.
Lots of people could not flash anything with HARD SPL 1.3 flashed.
Click to expand...
Click to collapse
Could you point me to SPL v. 1.2? I can't find it via the forum search.
nealed said:
SPL 9.99.CP will show with all HARD-SPLs I believe.
Click to expand...
Click to collapse
No you are wrong! SPL 9.99.CP is DES HARD-SPL and CP mean CrashProof.
IPL x.x.50xx is show with every HARD-SPL.
SPL 9.99.CP is okay! Have you tried to flash a original WM5 Rom?
sammy_deluxe said:
No you are wrong! SPL 9.99.CP is DES HARD-SPL and CP mean CrashProof.
IPL x.x.50xx is show with every HARD-SPL.
SPL 9.99.CP is okay! Have you tried to flash a original WM5 Rom?
Click to expand...
Click to collapse
No. If it might help, I'll try. Can you point me to where I can get an original german WM5 Rom?
Ok, found the original ROM Update from the HTC site. Flashed it. This time the device rebooted by itself. Result: I am still stuck with the bepe ROM 0.5. Updating did nothing!
paranoid2007 said:
Ok, found the original ROM Update from the HTC site. Flashed it. This time the device rebooted by itself. Result: I am still stuck with the bepe ROM 0.5. Updating did nothing!
Click to expand...
Click to collapse
try this way! http://wiki.xda-developers.com/index.php?pagename=Trinity_SDCardFlashing
sammy_deluxe said:
try this way! http://wiki.xda-developers.com/index.php?pagename=Trinity_SDCardFlashing
Click to expand...
Click to collapse
Doesn't work. Whenever I try to start Hard SPL, the bootloader shows up for about 5 seconds. Then the screen slowly starts fading to dark grey, so that I can't read anything on the display. Then nothing more happens.
try goin into the bootloader screen on the device first rather that using the update tool first.. this should work
steveecourt said:
try goin into the bootloader screen on the device first rather that using the update tool first.. this should work
Click to expand...
Click to collapse
OMG this worked! Thanks a million. Strangely enough, I tried it this morning without luck.
I also have SPL 9.99 CP and if you put a rom on the flash card it just seems to ignore the file and goes backk into bootloader
steveecourt said:
I also have SPL 9.99 CP and if you put a rom on the flash card it just seems to ignore the file and goes backk into bootloader
Click to expand...
Click to collapse
I have the same SPL but I had never flashed a rom from Flash card.. Could you explain more in the deep how it works? did it once with older Rom's?
Hi,
My Diamond has no response on the screen, so I think I need to return to factory for repairing. However I have difficulties in falling back to stock ROM and SPL.
From the Wiki:
---------------
STEP BY STEP HOW TO RETURN TO STOCK SPL - FOR WARRANTY REASONS ONLY!
0. be sure to first restore stock OS, and stock radio. stock SPL is always to be done last!!
...
-----------------
I can't flash my ROM to latest HK WWE CSL ROM (2.03) as it just stopped at 0%. I'm using SPL-1.30.OliNex.
Questions:
0) Why? Any step I've missed? I've just copied the .NBH from HTC official ROM download. Should I get the .NBH from the Wiki instead?
1) Should I flash to v1.93 (the very beginning of the ROM)?
2) Must the RADIO be flashed back as well? or the above Stock ROM has included the RADIO already?
3) Anyone can give me a reference on the step-by-step in details...
Thanks!
Please help...
F810
Questions:
f810 said:
0) Why? Any step I've missed? I've just copied the .NBH from HTC official ROM download. Should I get the .NBH from the Wiki instead?
Click to expand...
Click to collapse
If the latest was the offical from the site then you could use that - as you are having issues flashing this with 1.30 HSPL, I would suggest updating that to 1.40
f810 said:
1) Should I flash to v1.93 (the very beginning of the ROM)?
Click to expand...
Click to collapse
This might be a easier option and should work woth the 1.30 HSPL
f810 said:
2) Must the RADIO be flashed back as well? or the above Stock ROM has included the RADIO already?
Click to expand...
Click to collapse
This is recommended
f810 said:
3) Anyone can give me a reference on the step-by-step in details...
Click to expand...
Click to collapse
Its really straight forward like the WiKi suggests
This Thread may help
Thanks a lot.
Re Q3, so do you mean if I extracted the stock NBH, it's only OS but not including RADIO? If so, I will get the RADIO from wiki page later. Would you please clarify for me?
After your information, I think the steps in Wiki are clear. Thanks.
If this is HK ROM is the one you have downloaded from HTC PAGE then it has a radio included
Since my Diamond is totally malfunction in the touch screen, I can't response to all the confirmation & prompts...
I've failed to install Stock ROM and tried your recommendation on upgrading to HSPL 1.40. There was a confirmation on running the program in my Diamond and I can't press YES and now my diamond is just like bricked.
I've also tried pressing VOL DOWN + Reset to connect the Diamond via USB. The ROM Update Utility has "successfully" update the HSPL, but actually when I hard reset it and found it's still running 1.30... Can I just use this approach to fallback to Factory status??
Anyone has good idea on how to fallback to Factory Stock ROM, RADIO and SPL, provided that my screen has totally no response to me?
PLEASE...PLEASE...PLEASE help.
You will not be able to update olipros Hard SPL in bootloader mode as the SPL is protected and the 1.30 will prevent this although show its been done.
What you will need to do then is just load a 1.93 ROM from boot loader. the were some in that link i posted earlier. as to reverting to the default SPL - you may be luck not to need the screen for any confirmation. but running a new SPL to overwrite Oli's you will need to use windows and the RRU
I've tried to load 1.93 ROM to my diamond but failed on OliNex 1.30. The link in modmydiamond.info on OliNex 1.40 Signed seems not correct, as it's still 1.30 after flashed. I've then flashed UNSIGNED 1.40 OliNex SPL (also downloaded from modmydiamond.info) and now flashing the 1.93 ROM in progress from bootloader.
I will flash the Stock SPL through the Bootloader after that...I hope I can successfully fallback and get it repair...
Last question (I hope), the stock SPL should be 1.37 so I want to confirm whether it can boot 1.93 ROM.
Thanks a lot!
Because these Unsigned HARD SPL 's are write protected.....you will fail all the time. Not sure if stock SPL can undue the write protection but if you still get stuck after you try then in order to bypass write protection I know Jump SPL allows for this.
band27 said:
Because these Unsigned HARD SPL 's are write protected.....you will fail all the time. Not sure if stock SPL can undue the write protection but if you still get stuck after you try then in order to bypass write protection I know Jump SPL allows for this.
Click to expand...
Click to collapse
you're right. When I flash the Stock SPL, it is "successful" but actually it doesn't update the SPL (i.e yet running OliNex 1.40). Where can I get the Jump SPL?
Here you go....I did a search
Hi,
Sorry to use this thread but im also trying to install back to my original Diamond ROM and am currently using the rom developed by Diamond Project (1.93.456.2WWE) and i kept flashing it back using Signed V1.93 RUU and apprently the Diamond project words still keep showing out when i start my phone!
How do i completely remove the Diamond Project thing? Thank you!
Read this............Scroll to Post #39
http://forum.xda-developers.com/showthread.php?t=400950&page=4
band27 said:
Here you go....I did a search
Click to expand...
Click to collapse
I also got that but it's not win32 program... I believe it's running on the Diamond. But I've hard reset, and never able to setup as it's screen was not functioning now...
kawatsu said:
Hi,
Sorry to use this thread but im also trying to install back to my original Diamond ROM and am currently using the rom developed by Diamond Project (1.93.456.2WWE) and i kept flashing it back using Signed V1.93 RUU and apprently the Diamond project words still keep showing out when i start my phone!
How do i completely remove the Diamond Project thing? Thank you!
Click to expand...
Click to collapse
That ROM had a different boot image - so you need to replace that by flashing another splash .NBH file using RUU.
Original splash can be found HERE
and if needed CUSTOM RUU HERE
Just un-zip these and put the splash file in the same folder as the Custom RUU and run the RUU - the flash should take a few seconds and viola - bye bye Diamond project splash.
f810 said:
I've tried to load 1.93 ROM to my diamond but failed on OliNex 1.30. The link in modmydiamond.info on OliNex 1.40 Signed seems not correct, as it's still 1.30 after flashed. I've then flashed UNSIGNED 1.40 OliNex SPL (also downloaded from modmydiamond.info) and now flashing the 1.93 ROM in progress from bootloader.
I will flash the Stock SPL through the Bootloader after that...I hope I can successfully fallback and get it repair...
Last question (I hope), the stock SPL should be 1.37 so I want to confirm whether it can boot 1.93 ROM.
Thanks a lot!
Click to expand...
Click to collapse
I think as long as the SPL is changed and the ROM is of the original language the I think it should be OK to send back like that
f810 said:
you're right. When I flash the Stock SPL, it is "successful" but actually it doesn't update the SPL (i.e yet running OliNex 1.40). Where can I get the Jump SPL?
Click to expand...
Click to collapse
As said before; you should be able to successfully run the stock SPL using RUU - if you are trying this via bootloader it will not work.
Which is the original SPL?? 1.23, 1.34 or 1.37? I do recall taking a picture of the original SPL when i 1st got the Diamond for days like that but i just can't find it now
I'm bought it from Malaysia. Anybody can help me confirm this??
R3PUBL1K said:
As said before; you should be able to successfully run the stock SPL using RUU - if you are trying this via bootloader it will not work.
Click to expand...
Click to collapse
I've tried to connect to ActiveSync successfully although the Initial Setup wizard on my Diamond. I've then run the RUU from RUU-SSPL-withoutNBH.zip and put the stock SPL .NBH file into the extracted directory. It can retrieve my device info, and when I confirm the update of ROM, after 3-5 sec it said about connection failure. I can browse the Internal Storage at the moment yet.
I've then tried similar thing using the Custom RUU inside the package diamond-hspl-1.34.zip. This time I can see 100% update. When I press VolDown and reset, the SPL is still v1.40 ONliEx.
What's wrong with my procedures above?
f810 said:
I've tried to connect to ActiveSync successfully although the Initial Setup wizard on my Diamond. I've then run the RUU from RUU-SSPL-withoutNBH.zip and put the stock SPL .NBH file into the extracted directory. It can retrieve my device info, and when I confirm the update of ROM, after 3-5 sec it said about connection failure. I can browse the Internal Storage at the moment yet.
I've then tried similar thing using the Custom RUU inside the package diamond-hspl-1.34.zip. This time I can see 100% update. When I press VolDown and reset, the SPL is still v1.40 ONliEx.
What's wrong with my procedures above?
Click to expand...
Click to collapse
I think I miss the step of running the SSPL-Manual.exe because of my screen is not responding... Anyway for me to put it into the Windows Startup Folder?? When I use ActiveSync I can't see Windows directory.
Please...please...I miss this step only...
f810 said:
I think I miss the step of running the SSPL-Manual.exe because of my screen is not responding... Anyway for me to put it into the Windows Startup Folder?? When I use ActiveSync I can't see Windows directory.
Please...please...I miss this step only...
Click to expand...
Click to collapse
Can anyone help??
I know you guys most be tired of this but im still a lil confused about all this since i have searched around and i have still to know how to return the stock SPL...now i know theres alot of post that show how but what i need to do is find out one which i dont have to use my phone:
What i mean is....i dont have to copy SSManual.bat to my fun and run it from my phone...because i have to return my phone to HTC for warranty reasons but i cannot get passed the align screen configuration at boot since my touch is messed up (p.s. i can still flash and active sync)...
what i need to know is a way to return to the stock SPL without using the phone (except for Active Sync)...
p.s. if i have the ASIA WWE HK ROM on the SPL would be 1.34 or 1.93?
thank you!!
[SOLVED]
Basically, thanks to the ppl in this thread for helping.....since i couldnt get passed my align screen cause of hardware problems with my screen i couldnt access the sspl-manual in order to revert to stock spl so what i did is i flash my phone with Dia duit 1.4 which has no welcome screen or align screen so i could go thru to the phone then performed the sspl manual and reverted to the 1.93 spl (my version)and afterwards i flash my phone with the Asia HTC wwe orginal romhttp://forum.xda-developers.com/showthread.php?t=410720 ......i know ure supposed to first flash orginal rom and then the stock spl but i took a chance and it worked...THANKS u guys keep up the good work and now its up to HTC to fix my hardware....Hoping its on warranty
By the way right now im on Olinex 1.40
thank you again!!!
can't you install the hardspl through bootloader mode?
Unfortunately no, everytime i do either i get an error [202] or it goes straight to 100% but then when i check with the vol - and reset button it shows olinex 1.40
did anybody ever try to send it without reverting back to the stock spl ?
emy09 said:
did anybody ever try to send it without reverting back to the stock spl ?
Click to expand...
Click to collapse
Try to install a rom which don't have to align the screen. then you copy the file you wants from the phone.
Good luck
does anybody know of a rom like that that exists cause that sounds like a pretty good idea!!
hi
i had your problem and has olinex 1.40 anld like to restore hard spl
first you should install original rom on your device
then install original hard spl ( i try it )
download rom 1.93 WWE from the htc site (it should be 1.93)
then hard spl with it (copy sspl manual om your device run it then restart you device run it again then connect it to pc and run ruu
hard spl : http://rapidshare.com/files/215819452/1.93_Original.rar.html
sorry my English is not good
http://forum.xda-developers.com/showthread.php?t=493719
emy09 said:
does anybody know of a rom like that that exists cause that sounds like a pretty good idea!!
Click to expand...
Click to collapse
i think the new rom of suiller (diadiut 1.4) would do. you don't need to screen align after flashing.
azera_2000 said:
hi
i had your problem and has olinex 1.40 anld like to restore hard spl
first you should install original rom on your device
then install original hard spl ( i try it )
download rom 1.93 WWE from the htc site (it should be 1.93)
then hard spl with it (copy sspl manual om your device run it then restart you device run it again then connect it to pc and run ruu
hard spl : http://rapidshare.com/files/215819452/1.93_Original.rar.html
sorry my English is not good
Click to expand...
Click to collapse
I appreciate the help but the problem is that i cannot get passed the align screen of the first boot which means i cant run sspl manual since i cannot in the files from my phone.....also if i do flash the Dia duit 1.4 rom which does not boot with the align screen or welcome screen, dont i have to flash the original rom before putting the stock SPL !!.....thank you guys for the info
Due to a hardware problem in my Diamond I needed to restore it to manufacturer default. I didn't find a guide to this and since I've done the research anyway I thought I'd put together this little tutorial as the information was somewhat scattered around the forum. I hope this guide will be of use for the community.
My phone was originally branded and sim-locked by 3. After I was through with it, it was SIM-unlocked, security unlocked and had HSPL, custom ROM and a radio ported from another device. The steps below is what I did to restore it to stock. All steps might not be neccessary for you. This procedure might also work for other devices than the Diamond, but of course you need other versions of SPL, ROM etc.
1. Backup everything on your phone to your computer - use activesync, PIMbackup etc and make a copy of your Internal Storage.
2. Make a hard reset (hold vol down + enter and soft reset) and chose to format moviNAND. This step is only neccessary if you want to wipe your Internal Storage before you send the device in for repair, but I recommend it.
3. Go to www.htc.com and download the latest stock ROM (includes stock radio and SPL). You find it under Support and you enter your s/n to get the correct stock ROM for your device, complete with branding for your operator. You can also find stock ROMS here: http://forum.xda-developers.com/showthread.php?t=471699
4. Flash the stock ROM. Now you have stock ROM and Radio on your device. Stock SPL will not be installed until you've replaced HSPL with an older stock SPL and flashed ROM again.
5. Get RUU-SSPL and stock SPL from HERE:
http://forum.xda-developers.com/showpost.php?p=2324829&postcount=39. I used the stock 1.93 SPL. Some instructions and info about restoring stock SPL is in the linked post by cmonex and due credit goes to her. I will repeat some of that info to keep this guide step-by-step. EDIT: Stock SPL 2.03 can be found here: http://forum.xda-developers.com/showpost.php?p=3359191&postcount=390
6. Put the .nbh file from the SPL you downloaded into the same folder as the extracted contents of RUU-SSPL-withoutNBH.zip and run the RUU. This flashes an old stock SPL.
7. Flash your stock ROM from step 3 again. This step is neccessary to get the correct stock SPL on your device, eg. the one that corresponds with the stock ROM you've downloaded in step 3. It was not installed in step 4, because then you still had HSPL. In step 6 you've installed a stock SPL and now the correct stock SPL will flash along with the stock ROM. After this step I got SPL 2.03 on my Diamond.
8. Remove the Security Unlock from your device using the instructions and Security Relocker by Olinex from this post by cmonex: http://forum.xda-developers.com/showpost.php?p=3299516&postcount=492
Now, my Diamond is still SIM-unlocked. I have not managed to find any info about how to restore the SIM-lock, but it is hopefully not neccessary for warranty. As far as I can tell, the unlock doesn't show anywhere, but of course all they need to do is to try a SIM-card from another operator...
If anyone has info about how to restore SIM-lock, then I'll update this guide with that info.
good job...
moderator make this "sticky"
3dward87 said:
good job...
moderator make this "sticky"
Click to expand...
Click to collapse
I second that, it contains links to stock ROMs, that'll hopefully stop a million topics about it lol.
This does not work for me.. However i have a problem. the touch screen of my device is not working.. so i can't get pass the allign screen part .. and for somereason the ruu won't connect to phone when it is at tha part so i can't install the spl.. the only way i can do that i through bootloader and it flashes fine but when i then look in bootloader to see the spl it still shows 1.40 olinex..
Da9L said:
This does not work for me.. However i have a problem. the touch screen of my device is not working.. so i can't get pass the allign screen part .. and for somereason the ruu won't connect to phone when it is at tha part so i can't install the spl.. the only way i can do that i through bootloader and it flashes fine but when i then look in bootloader to see the spl it still shows 1.40 olinex..
Click to expand...
Click to collapse
You're right, I tried it too. Flashing SPL through bootloader doesn't work.
You can try using JumpSPL instead, I've attached it in this post. I don't think JumpSPL will require any screen prompts on your Diamond. You can read instructions.txt in the zip, but it's just really the .bat file so you get an idea of what it's doing. Run the .bat, press enter at the prompts and run the RUU for your stock SPL instead of HSPL when asked. At your own risk, I have not tried this myself.
where can i read more information about jumpspl, how it works and everything?
eranyanay said:
where can i read more information about jumpspl, how it works and everything?
Click to expand...
Click to collapse
Look in the Xda-wiki, search and google, and not just in the Diamond section.
sticky please
this needs to be a sticky topic.
losdrivare said:
You're right, I tried it too. Flashing SPL through bootloader doesn't work.
You can try using JumpSPL instead, I've attached it in this post. I don't think JumpSPL will require any screen prompts on your Diamond. You can read instructions.txt in the zip, but it's just really the .bat file so you get an idea of what it's doing. Run the .bat, press enter at the prompts and run the RUU for your stock SPL instead of HSPL when asked. At your own risk, I have not tried this myself.
Click to expand...
Click to collapse
I have just tried it and it gets stuck where it should run the JumpSPL.exe on the device. After a few minutes it comes with an error:
"ERROR: CreateProcess failed with Errorcode = 30123
- UNKNOWNERROR: 0x000075ab"
This is not good I just think its wierd that because of a broken screen it is impossible for me to get the stock spl flashed back on.
Da9L said:
I have just tried it and it gets stuck where it should run the JumpSPL.exe on the device. After a few minutes it comes with an error:
"ERROR: CreateProcess failed with Errorcode = 30123
- UNKNOWNERROR: 0x000075ab"
This is not good I just think its wierd that because of a broken screen it is impossible for me to get the stock spl flashed back on.
Click to expand...
Click to collapse
Sorry to hear it and I'm afraid I'm out of ideas. After all, my little tutorial is primarily aimed at those whose Diamonds have working screens...
On another note, my Diamond came back from warranty repair and the repair shop had not noticed anything that would void my warranty. In the meantime I got myself a Topaz and now I've sold my Diamond, but I'll be checking this thread from time to time.
Hey thanks bro..!! I need to give mine for reparing..
I have a hardware problem with the reset button.. Do you think I should flash my diamond back to stock? (I don't think they'll check the software right?)
donsalari said:
Hey thanks bro..!! I need to give mine for reparing..
I have a hardware problem with the reset button.. Do you think I should flash my diamond back to stock? (I don't think they'll check the software right?)
Click to expand...
Click to collapse
I would restore it to stock anyway. Some workshops actually look for excuses/reasons why the warranty won't apply so I say you'd definitly be taking a risk if you didn't.
losdrivare said:
I would restore it to stock anyway. Some workshops actually look for excuses/reasons why the warranty won't apply so I say you'd definitly be taking a risk if you didn't.
Click to expand...
Click to collapse
Very true!!! Ok cool... Flashing back to stock!!
Thanks..
Damn.. Hmm anyway then i will have to try the risk and sending it in with hardspl on it.. ! I Hope they won't see it.
Da9L said:
Damn.. Hmm anyway then i will have to try the risk and sending it in with hardspl on it.. ! I Hope they won't see it.
Click to expand...
Click to collapse
Another idea: maybe you can find some a VNC program that also works the "other way" with windows mobile, so that you can get a window on your PC with the screen of your device?
Hi. I'm an orange user and i dont know what SPL i should use to send back to warranty!
DOes anyone can recommend it please?
My Orange ROM is RUU_Diamond_HTC_WWE_1.93.405.1_Radio_Signed_Diamon d_52.29.25.12_1.00.25.05_Ship
UPDATE - i flashed the new rom and i tried to put the original SPL, however it still showing 1.40 Olinex in the bootloader and it still says security unlocked.
Any help please...
Hi I m singapore user i dont know what is the original spl 1.23 ??? i 4get leh can u tell me
bro i try 1.23.000 that version are u sure this is offical stockspl
as i remember it shld be SSPL not SPL somemore when running the tri-boot colour is diffferent from the offical 1
1 . Press volume up restore factory default bla bla bla ..
2 . Press volume down restore factory default and format the internal storage
3 . Press any button to cancel
Where is 2 n 3 ??? gone oridi
herpez said:
Hi. I'm an orange user and i dont know what SPL i should use to send back to warranty!
DOes anyone can recommend it please?
My Orange ROM is RUU_Diamond_HTC_WWE_1.93.405.1_Radio_Signed_Diamon d_52.29.25.12_1.00.25.05_Ship
UPDATE - i flashed the new rom and i tried to put the original SPL, however it still showing 1.40 Olinex in the bootloader and it still says security unlocked.
Any help please...
Click to expand...
Click to collapse
k3nnyboiboi said:
Hi I m singapore user i dont know what is the original spl 1.23 ??? i 4get leh can u tell me
Click to expand...
Click to collapse
If you manage to install ANY stock SPL and then flash the correct ROM for your country and operator then you automatically get the correct SPL too, since stock ROMs include SPL. If you go to htc.com and type in your s/n then you automatically get the latest ROM for your device and operator.
k3nnyboiboi said:
bro i try 1.23.000 that version are u sure this is offical stockspl
as i remember it shld be SSPL not SPL somemore when running the tri-boot colour is diffferent from the offical 1
1 . Press volume up restore factory default bla bla bla ..
2 . Press volume down restore factory default and format the internal storage
3 . Press any button to cancel
Where is 2 n 3 ??? gone oridi
Click to expand...
Click to collapse
I only link to the SPLs provided by olipro and cmonex in the hard-SPL thread. If you need closer info about SPLs I suggest you ask there. I only tried to revert back to stock SPL 1.93 myself and it worked just like described in first post.
Thanks Op
Managed to restore it no problem, but took ages
So as you can figure out from the thread title I have a problem flashing my htc diamond.
I have installed a HardSPL version 1.30 OliNex, I can confirm that becouse on the three color screen there is a text saying "1.30 OliNex".
I still have the original ROM that comes with the phone when I bought it, so this meant to be my first flashing.
I want to flash the phone with this rom http://forum.xda-developers.com/showthread.php?t=593678 it is a WM 6.5 based ROM.
Because in the ROM package there wasn't a ROMUpdateUtility.exe I used it from other ROM package.
Connected via ActiveSync and followed the wizard. The phone reset and there came a gray screen with a progress bar. Now both progress bars on the phone and on the PC screen remain 0% and after a wile RUU finished with 262 ERROR Connection error, see the attached picture.
After that I tried to flash it from Internal Storage. A followed the steps according the procedure, and after the three colored screen it came the gray screen with "Loading..." message. I waited for almost 30 minutes and nothing happened.
What seems to be the problem?
I assumed about firewall disabling the connection. But I turned off the firewall and again the same story.
Then somewhere I found that there is incompatibility with the RUU and HardSPL version, but tried to flash with the same RUU that I used when I was installing HardSPL.
Then I tough that the problem is about flashing unsigned ROM on a signed HSPL, but it is not that the ROM is signed.
I am afraid to use MTTY so I don't brick my phone, because this is my first time flashing a Diamond.
I'm confused What seems to be the problem?
Any help can be welcomed.
Could this be indication of a hardware problem? When waiting for the "Loading..." message disappear the back cover warms a little.
Thanks.
1. Did you use the RUU from my thread?
2. NEVER USE AN H-SPL RUU TO FLASH ANYTHING OTHER THAN H-SPL!
3. is this a CMDA phone. IE, what network are you on?
Well no I didn't use the RUU from your thread, I've used a RUU from other ROM package.
This is not a CDMA phone I'm on T-Mobile Macedonia network. And the phone looks like this
On other Macedonian forum they told me it is a hardware problem. Can this be true?
So what do you think about my problem?
Well no I didn't use the RUU from your thread, I've used a RUU from other ROM package.
This is not a CDMA phone I'm on T-Mobile Macedonia network. And the phone looks like this
On other Macedonian forum they told me it is a hardware problem. Can this be true?
So what do you think about my problem?
EDIT: I did tried the RUU you recommended in your thread but it's the same.
I think it is in the PDA.
Configure active sync, and uncheck "allow usb connection" and try again.
For updating from internal storage you must have to copy the rom to the root of internal storage with a special name, ""diamimg.nbh"
Hmmm..
What he said... and...
Should have used one of the earlier SPLs. you only need to use the latest one if you are having problems with the older versions. I have the same diamond and used an early SPL.
Upgrade the radio rom first and go with a rom that's version 6.1 not 6.5 as most 6.5 roms now pack the Sense application.. (IMO Non-Sense, Senseless (Not enought ram or responsiveness))
Old roms here
http://forum.xda-developers.com/showthread.php?t=470757
Give olinex some cash for his Diamond Unlocker as this is the surefire way to fix it.
johnyboy_ said:
Configure active sync, and uncheck "allow usb connection" and try again.
For updating from internal storage you must have to copy the rom to the root of internal storage with a special name, ""diamimg.nbh"
Click to expand...
Click to collapse
The connection between PC and PDA is made, because as I said there is a progress bar on the phone screen too.
djfuego said:
What he said... and...
Should have used one of the earlier SPLs. you only need to use the latest one if you are having problems with the older versions. I have the same diamond and used an early SPL.
Upgrade the radio rom first and go with a rom that's version 6.1 not 6.5 as most 6.5 roms now pack the Sense application.. (IMO Non-Sense, Senseless (Not enought ram or responsiveness))
Old roms here
http://forum.xda-developers.com/showthread.php?t=470757
Give olinex some cash for his Diamond Unlocker as this is the surefire way to fix it.
Click to expand...
Click to collapse
As I understand you, you are saying to install later version of Hard SPL right?
So to install a new version of Hard SPL I just need to do the same procedure as the first time, or I have to uninstall the previous one?
And please help me which version of Hard SPL is safest to install? I'm afraid of the developer versions or maybe they aren't so scary
Are you a 100% positive it is the HardSPL?
djandreski said:
And please help me which version of Hard SPL is safest to install? I'm afraid of the developer versions or maybe they aren't so scary
Are you a 100% positive it is the HardSPL?
Click to expand...
Click to collapse
Presuming from your post, you are using a signed Olinex SPL, i doubt that the rom has been signed be OliNex, the only difference with Dev is you can flash any Rom, flash the Dev one from my thread, nothing to be afraid of
Good Luck
Badwolve1
What are the steps of installing new SPL?
Do I just need to do the same procedure as the first time, or I have to uninstall the previous one(somehow)?
UPDATE: I did it, I successfully flashed my Diamond PDA! It seams that the problem was in the SPL I installed 1.40 OliNex Unsigned and it flashed like a charm. Thanks guys for the help. Now this thread can be closed, or do I have to close it myself.
Great!
Glad it all worked out