Universal RUU - CID Checking bypassed - JASJAR, XDA Exec, MDA Pro Software Upgrading

Hi, after speaking to Midget_1990, I have patched the RUU for the Universal to allow flashing with any CID on your phone, this is the official Universal RUU (with a slight GUI mod by someone Midget_1990 mentioned)
so have at it... enjoy.

thanks, was just about to upload it

thanks,
just downloaded and have a try

allway said:
thanks,
just downloaded and have a try
Click to expand...
Click to collapse
it does work... just has the minor caveat that it'll try to flash a Universal when it's not actually plugged in... so try not to be a complete plank with it.

Olipro said:
it does work... just has the minor caveat that it'll try to flash a Universal when it's not actually plugged in... so try not to be a complete plank with it.
Click to expand...
Click to collapse
i have flashed my universal with the new RUU.
It works fine.

Olipro
Is it possible that you will make a HardSPL for Universal?
We still have no way to recover bricked radio...

we were discussing that earlier. the nogsm shows when the radio bootloader is not written to the device properly for whatever reason. its still early days but it may be possible to create a new radio bootloader that cant be overwritten so that problem wont occur. however it wont fix thoses who allready ahve the problem.

Skwyk said:
Olipro
Is it possible that you will make a HardSPL for Universal?
We still have no way to recover bricked radio...
Click to expand...
Click to collapse
ok, if you are flashing a radio, and you brick your radio, but not the radio bootloader, then you should be able to recover by reflashing.
if you brick the Radio bootloader, then unfortunately, there is no way for you to recover from this; possibly the only way of recovery is directly accessing the radio chip pins via whatever interface it is... perhaps i2c? and flashing on a radio BL again through a separate interface... meaning you then need a radio bootloader binary in the correct format.

Olipro said:
ok, if you are flashing a radio, and you brick your radio, but not the radio bootloader, then you should be able to recover by reflashing.
Click to expand...
Click to collapse
Not in 100% of the cases... there are some situations where the radio bootloader is intact, but the radio is screwed, this causes all bootloader commands that require radio seclevel to be queried to hang the device (like 'task 32' or 'info 2'), thus not being able to flash it with the usual RUUs.
If this happens, it can easily be fixed with hermflasher by flashing the raw radio without prior authenticating to bootloader.

Olipro!!! am having No GSM here!!!
Dear Dr. PDAs
My Universal is suffering for bad blocks of Radio ROM i guess.
it Says NO GSM when boots.
Boots WIN CE very well
can't flash radio rom.
Please tell if we could have HardSPL for Universal or is there any other way to recover it...
waiting.
farehmani

hi everyone i m in need of new rom for my XDA Exec Universal plz help me as i m ver new.

V1640 and flash rom radio problem
hello,
On my V1640 my radio rom is version :0.00.00, and I can't flash it with a newradio rom. It is probably a CID Lock problem, How works Universal RUU ?
Is there a tutorial for flashing with Universal RUU ?
thanks
Regards

Has anyone got anywhere to fix problems with radio mess ups I have an O2 XDA Exec and loads 2.05 ok but error when flashing any Radio. Tried all I can find but no luck

simpleparab said:
hi everyone i m in need of new rom for my XDA Exec Universal plz help me as i m ver new.
Click to expand...
Click to collapse
Try to serch forum
Or, for lasy people try my folder blow

Flashing radio rom Ok !!!
I flashed the radio rom on another PC.... It works fine.
Try this..good luck

Flashing the O2 original ROm with this RUU
Hi,
Can i use this RUU combined with the original ROM from O2 to flash?
My current ROM:
ROM 1.13.82
Radio 1.04.02
ExtROM 1.13.188
New ROM available:
ROM 1.30.107
Radio 1.09.00
ExtROM 1.30.162
I have to use the bootloader mode to flash the new ROM because my XDA Exec has problem on connection with my PC via Active Sync. My Xda just dont sync with my PC where there is no connection established.
Hopefully someone can tell me what is this RUU? Whats the different than the original?

bejoa said:
Flashing radio rom Ok !!!
I flashed the radio rom on another PC.... It works fine.
Try this..good luck
Click to expand...
Click to collapse
this is the second time ppl have been able to flash no GSM Universals by using a nother PC. What was the spec of this pc and what was installed and Not installed in it.? I really want to unbrick my Universsal

I flashed my universal on a Laptop :
Gericom Select 2580+
AMD 2500+, 512 Mo ram, 80 Gb HD,
Windows XP Home SP2 pack
ActiveSync 4.2
Universal RUU
nothing special installed...
Good luck

bejoa,
what was the boot loader version of ur universal?

It is version 1.0

Related

noob needed help

my hermes got "no gsm" , after i upgrade it to wm6
so i read the "wiki"...i found that i bricked my radio rom
SPL HTC_BOOT Boot OS? No GSM? KITL Diagnostic
Any Any Yes Yes --- bricked while flashing
radio, OS can boot
Solution
1. Flash Hard-SPL
2.Flash any radio in NBH format
Do both steps using SSPL+ActiveSync
i am matched with this situation
but i got confuse with the step 2
should i use the Radio 1.43.00.00(ftp://xda:[email protected]/Uploads/Hermes/Radio 1.43.00.00.zip)
or (ftp://xda:[email protected]a-developers.com/Uploads/Hermes/HERM_Radio_Only_1.43.00.00_CustomRUU.rar)
kuetsum said:
my hermes got "no gsm" , after i upgrade it to wm6
so i read the "wiki"...i found that i bricked my radio rom
SPL HTC_BOOT Boot OS? No GSM? KITL Diagnostic
Any Any Yes Yes --- bricked while flashing
radio, OS can boot
Solution
1. Flash Hard-SPL
2.Flash any radio in NBH format
Do both steps using SSPL+ActiveSync
i am matched with this situation
but i got confuse with the step 2
should i use the Radio 1.43.00.00(ftp://xda:[email protected]/Uploads/Hermes/Radio%201.43.00.00.zip)
or (ftp://xda:[email protected]/Uploads/Hermes/HERM_Radio_Only_1.43.00.00_CustomRUU.rar)
Click to expand...
Click to collapse
use the radio 1.43 (first option you have there) ftp://xda:[email protected]/Uploads/Hermes/Radio 1.43.00.00.zip)
walshieau said:
use the radio 1.43 (first option you have there) ftp://xda:[email protected]/Uploads/Hermes/Radio 1.43.00.00.zip)
Click to expand...
Click to collapse
I got a bigger problem..
my pc suddenly shutdown....while upgrading the rom..
my hermes is stuck in the bootloader screen
it can detect the usb sync
but the upgrade program cant find my hermes with and error
what should i do now?
T_T
I'd recommend you check out the WIKI for upgrade problems HERE. Also there's a section on what to do if you've bricked your phone HERE.
Hope this helps

Help no gsm can flash to any rom without radio

Help
Have read as much info as i can about bricked phone.
Have no radio working shows no gsm on boot
It apears that i can flash to any rom with out a radio, if i flash to one that includes it its stops at 11 - 13% and comes up with an error message 262.
have olipro 2.30 and hardslp7
if i try to flash radiio rom only it wont and stays at 0% until errror message 262
so its a 1a
but not having any luck
please help as this was my dads phone
its an orange spv3100/ herms 100
try reinstalling a stock rom. might work but if you cant install a radio it looks like you have a nice pda but not a phone anymore...
No Not really
The only reason i was having to reflash the phone was that it was locking up all the time, even having flashed the phone it was having problems with Tom Tom.
Please HELLP!
Can some one please advise me on this situation,
is there any way of sorting this out?
stock orange m3100 rom wont flash
Just tried standard orange m3100 rom
it stops at 12% and wont continue,
seems any rom with a radio wont flash past 12/13%
any radio free rom is fine
it wont flash radio only roms
PLEASE HELP
Have you tried flashing radio only?
photoscubaman said:
Just tried standard orange m3100 rom
it stops at 12% and wont continue,
seems any rom with a radio wont flash past 12/13%
any radio free rom is fine
it wont flash radio only roms
PLEASE HELP
Click to expand...
Click to collapse
Have tried radio only roms,
they wont work at all and stays at 0%
have olivpro 2.30 and hardspl7
thought this was ment to prevent bricking?
no, it improves chances of recovering a brick but wont stop it from happening. It loks like your radio is corrupted. You might have to bite the bullet and tell your dad his phone no longer works... sorry for the bad news...
have you tried flashing a rom with radio included through yur sd card. had same issue and this worked for me.
If ya can't install a radio, sounds like your stuck with a pda and not a phone.
Have you tried a number or radio's?
As ultramag69 says
no, it improves chances of recovering a brick but wont stop it from happening. It loks like your radio is corrupted. You might have to bite the bullet and tell your dad his phone no longer works... sorry for the bad news...
Click to expand...
Click to collapse
using hardsplv7 improves chances of recovering, but nothing is 100%
If you flash your phone with manufacturers rom and get everything back to original, see if orange or manufacturer will fix it under warranty or insurance. THIS IS A LAST RESORT AS IF THEY DIG DEEP AND KNOW YOU HAVE MESSED WITH PHONE, THEY'LL DO NOTHING FOR YOU!!!
Personally I have returned phone once due to not being able to receive or make calls. I flashed original rom etc but forgot to put original radio back on. They never noticed and I got my phone back fixed. But this is a BIG RISK.
have now managed to get spl 1.01 on the phone
trying to change to spl 1.04 and reflashing!
however now when i task 32
it has
level FF not Level 0???
any ideas??
shamless bump
Isnt there anybody that can help me?
please
photoscubaman said:
have now managed to get spl 1.01 on the phone
trying to change to spl 1.04 and reflashing!
however now when i task 32
it has
level FF not Level 0???
any ideas??
Click to expand...
Click to collapse
Ditto.
Is there anyway of fixing the corrupted radio? is there no way to "re-write" the radio bootloader?
obviously the radio bootloaders have changed over the different versions of the roms so why cant we "re-construct" the bootloaders in this fashion?
Referring to :HERMES Bootloader 1.01 MFG (WIKI) I cant use the "Flashing SPL-1.04 again" method because my radio is corrupted, so, I lose SuperCID, and don't have access to the lnb command; is there a SPL-1.04.nbS that we can use?!
If there is, would it allow us to use a radio of that version? or is this mute?
I've read several threads and the wiki several times, but, it seems this corrupted radio issue is something new that the wiki's are partially addressing, or, whatever has caused the radio to suddenly become corrupt requires a new method to fix it.
I know i've said I've read the forums, wiki, but perhaps I've missed something? Any assistance is appreciated!
I was wondering if any body had spl 1.04 on their mini sd card?
the method were you just transfer over to the mini card and click on it.
i managed to change my boot loader to version 1.01 this way.
if i can change it to 1.04 can i flash to radio with out it stopping.
thanks
just solved exact problem
Hi
i have been dealing with the same problem for 4.5 hours finally with the help of wiki and pof 's posts i managed to unbrick radio.
first of all i tried almost evceryting. i finally succeed by reseting radio sector. i used mtty to gel into hermes and used commands of one of pof's posts for erasing radio sector.
i dont remember the link but google xda for it. then i flashed tweaked version wich is inclueded in unlocker by pof i aborted the operation in unlocking phase then installed hardspl7
i can use my phone now radio version is 1.10 sth but i didnt tried to install newer radio ( too tired :=) )
i hope it is usefull if anything not clear PM me or write here....
PS:Many many thanx to pof...
bartan
bartan said:
Hi
i have been dealing with the same problem for 4.5 hours finally with the help of wiki and pof 's posts i managed to unbrick radio.
first of all i tried almost evceryting. i finally succeed by reseting radio sector. i used mtty to gel into hermes and used commands of one of pof's posts for erasing radio sector.
i dont remember the link but google xda for it. then i flashed tweaked version wich is inclueded in unlocker by pof i aborted the operation in unlocking phase then installed hardspl7
i can use my phone now radio version is 1.10 sth but i didnt tried to install newer radio ( too tired :=) )
i hope it is usefull if anything not clear PM me or write here....
PS:Many many thanx to pof...
bartan
Click to expand...
Click to collapse
This link you speak of is of high importance!! what were the commands? what was the link?
http://forum.xda-developers.com/archive/index.php/t-280372.html
but after installing radio 1.47 it happened again in one call.
still in square one ....
No SD-card install works (stucks in GSM)
no shipped rom works
i want to ask if there is anyway to erase the whole radio sector ??
rerase command did not work on my hermes may be pof has some solution to this.
bartan
After lots and lots of reading the wiki's and forums over and over again I believe I may have solved the radio corruption problem on my 8525.
Just to let everyone know that I've tried flashing several SPL's; 1.01 MFG, 1.04, 1.10 Oli, 2.10 Oli, 2.60 Oli. Back and forth between the versions but finally I stayed put at 1.10.
I have/had a type 1a brick, but, not from flashing, everything was working great and then it just died. I tried Method 1 of Problem 5: Device shows NO GSM when booting more times then i would like to remember, however, nothing worked. When i tried a Radio only flash it failed at 0% and when i tried a FULL RUU it failed at 12/13% (GSM.nb). Convinced I had a $500 paper weight I got angry tried Method 2 of Problem 5 (see above link) ... strangely on the first try i was able to see the radio (1.40.30.00) and the protocol version as well...
I then thought this was too good to be true and then soft-reset my phone; BAM! "NO GSM".... I tried several times and then finally got the version readouts again... So i soft-reset into bootloader mode
Code:
typed: info 2
returned: HTCS
typed: task 32
returned: Level = 0
typed: rtask b
returned: AT-Command Interpreter ready <--------- YES!!!
I was then able to get enter the AT/Radio Commands so i did what anyone else would do.... FLASH ANOTHER RADIO!!!
I flashed the Radio from HTC_Hermes_SIM_Unlock_v2a and it just finished... I got an error at the end, and after the soft-reset the version stayed 1.40.30.00, but once booted into WM6.1 it immediately picked up the 3G signal... I hope this lasts longer then others have reported.
Should i try to flash another radio that is radio_bootloader 108???
*sigh* ... froze in WM6.1 reset then "No GSM" again... so then i tried HTC_Hermes_SIM_CID_Unlock_v3a but it failed because I kept getting No GSM; so i did the battery trick to get version info's then ran the .bat as instructed and it perfomed the unlock; this time it reflected the radio 1.16.0.0
since I know what it takes to get the radio to flash, i'm trying RUU_Hermes_CINGULAR_WWE_3.62.502.3_6275_1.54.07.00_108_UOOS_SVN05_Ship.exe ..... i mean what do i have to lose right?
[EDIT] it worked... so lets see what happens.... [/EDIT]
[EDIT2] Radio is 1.54.07.00 & Protocol is 32.86u.7020.23H ... so it looks like its perm now... I've been able to send and recieve calls now too.... [/EDIT2]
after several hours of usage, radio no longer responds and WM becomes unstable and after a soft-reset I get "No GSM" ...
Question to Olipro, Des, pof:
Is it possible to log the beginning bootup screen to see what exactly triggers the "No GSM" vs the radio/protocol versions?!?! there has to be something that were missing... it would seem ever since radio 108 this problems have arisen... comments?

Problem to flash Radio

Hello,
I am trying to flash my Diamond radio with RUU and radio 10.0.25.05 and my ROM is bElite v0.95 Premium.
I have flashed my ROM without problem but i can't manage to flash my radio. Eadch time i am launching flash process for radio, the process is beginning but stops at 0% and it fails because of a connection problem (error 262)
Could someone tells me what is the problem and helps me?
I have searche d everywhere in the forum. I ve heard about a unsigned and signed SPL. Maybe it's the same trick about RUU and I haven t got the good one...? Could someone just give me a link to the radio version 10.0.25.05 and to the Diamond Custom RUU I could use?
I am afraid to brick my phone...
Thanks for you answer
Please...
Does someone can help me?
it seems my problem can come from vista drivers. I foud a topic :
http://mahmood1.com/upgrade_pocket_pc_ruu_in_vista.aspx
But even folowing the instructions my update is still locked at 0% and tells me an error 262.
I ve done the whole instructions and installed the old driver but no matters. Somebody knows a way to solve my problem?
cdfr31 said:
Hello,
I am trying to flash my Diamond radio with RUU and radio 10.0.25.05 and my ROM is bElite v0.95 Premium.
I have flashed my ROM without problem but i can't manage to flash my radio. Eadch time i am launching flash process for radio, the process is beginning but stops at 0% and it fails because of a connection problem (error 262)
Could someone tells me what is the problem and helps me?
I have searche d everywhere in the forum. I ve heard about a unsigned and signed SPL. Maybe it's the same trick about RUU and I haven t got the good one...? Could someone just give me a link to the radio version 10.0.25.05 and to the Diamond Custom RUU I could use?
I am afraid to brick my phone...
Thanks for you answer
Click to expand...
Click to collapse
Using signed Hard-SPL?
Use this this to flash your radio : http://htcroms.aplace4u.biz/signed/radio/Diamond_Radio_1.00.25.05.rar
Hi Corian,
Thnaks to you I ve finaly flashed my radio!
Your trick was the good one.
Now I am trying to install a new rom casue i dont like the 0.95 bepe elite.
I have exactly the same problem with every flash i am attempting. It stays at 0% and tells me a 262 error.
My SPL is olinex 1.30.
Could you tell me whats the best and if you can give me the link to download the good files.
I d like to install an official HTC Rom and maybe for this i have to change the SPL?
Thanks for your great help.
HI,
Finally I have solved all py problems.
The problem was coming from the hard SPL I had installed.
I ve managed to change the hard spl which wasn t possible. I had to force the mode bootloadrer and then the hard spl was flashed and replaced by 1.40 Olinex unsigned.
Then I flashed rom and radio and splash screen without any problem.
In fact the whole thing about drvier Vista wasn t the problem I think.
Thanks to Corian who helped me to identify the source of the problem : incompatibility with hard spl taking only signed things.

Urgent! My diamond has hardware problem and need to fallback to stock ROM and SPL.

Hi,
My Diamond has no response on the screen, so I think I need to return to factory for repairing. However I have difficulties in falling back to stock ROM and SPL.
From the Wiki:
---------------
STEP BY STEP HOW TO RETURN TO STOCK SPL - FOR WARRANTY REASONS ONLY!
0. be sure to first restore stock OS, and stock radio. stock SPL is always to be done last!!
...
-----------------
I can't flash my ROM to latest HK WWE CSL ROM (2.03) as it just stopped at 0%. I'm using SPL-1.30.OliNex.
Questions:
0) Why? Any step I've missed? I've just copied the .NBH from HTC official ROM download. Should I get the .NBH from the Wiki instead?
1) Should I flash to v1.93 (the very beginning of the ROM)?
2) Must the RADIO be flashed back as well? or the above Stock ROM has included the RADIO already?
3) Anyone can give me a reference on the step-by-step in details...
Thanks!
Please help...
F810
Questions:
f810 said:
0) Why? Any step I've missed? I've just copied the .NBH from HTC official ROM download. Should I get the .NBH from the Wiki instead?
Click to expand...
Click to collapse
If the latest was the offical from the site then you could use that - as you are having issues flashing this with 1.30 HSPL, I would suggest updating that to 1.40
f810 said:
1) Should I flash to v1.93 (the very beginning of the ROM)?
Click to expand...
Click to collapse
This might be a easier option and should work woth the 1.30 HSPL
f810 said:
2) Must the RADIO be flashed back as well? or the above Stock ROM has included the RADIO already?
Click to expand...
Click to collapse
This is recommended
f810 said:
3) Anyone can give me a reference on the step-by-step in details...
Click to expand...
Click to collapse
Its really straight forward like the WiKi suggests
This Thread may help
Thanks a lot.
Re Q3, so do you mean if I extracted the stock NBH, it's only OS but not including RADIO? If so, I will get the RADIO from wiki page later. Would you please clarify for me?
After your information, I think the steps in Wiki are clear. Thanks.
If this is HK ROM is the one you have downloaded from HTC PAGE then it has a radio included
Since my Diamond is totally malfunction in the touch screen, I can't response to all the confirmation & prompts...
I've failed to install Stock ROM and tried your recommendation on upgrading to HSPL 1.40. There was a confirmation on running the program in my Diamond and I can't press YES and now my diamond is just like bricked.
I've also tried pressing VOL DOWN + Reset to connect the Diamond via USB. The ROM Update Utility has "successfully" update the HSPL, but actually when I hard reset it and found it's still running 1.30... Can I just use this approach to fallback to Factory status??
Anyone has good idea on how to fallback to Factory Stock ROM, RADIO and SPL, provided that my screen has totally no response to me?
PLEASE...PLEASE...PLEASE help.
You will not be able to update olipros Hard SPL in bootloader mode as the SPL is protected and the 1.30 will prevent this although show its been done.
What you will need to do then is just load a 1.93 ROM from boot loader. the were some in that link i posted earlier. as to reverting to the default SPL - you may be luck not to need the screen for any confirmation. but running a new SPL to overwrite Oli's you will need to use windows and the RRU
I've tried to load 1.93 ROM to my diamond but failed on OliNex 1.30. The link in modmydiamond.info on OliNex 1.40 Signed seems not correct, as it's still 1.30 after flashed. I've then flashed UNSIGNED 1.40 OliNex SPL (also downloaded from modmydiamond.info) and now flashing the 1.93 ROM in progress from bootloader.
I will flash the Stock SPL through the Bootloader after that...I hope I can successfully fallback and get it repair...
Last question (I hope), the stock SPL should be 1.37 so I want to confirm whether it can boot 1.93 ROM.
Thanks a lot!
Because these Unsigned HARD SPL 's are write protected.....you will fail all the time. Not sure if stock SPL can undue the write protection but if you still get stuck after you try then in order to bypass write protection I know Jump SPL allows for this.
band27 said:
Because these Unsigned HARD SPL 's are write protected.....you will fail all the time. Not sure if stock SPL can undue the write protection but if you still get stuck after you try then in order to bypass write protection I know Jump SPL allows for this.
Click to expand...
Click to collapse
you're right. When I flash the Stock SPL, it is "successful" but actually it doesn't update the SPL (i.e yet running OliNex 1.40). Where can I get the Jump SPL?
Here you go....I did a search
Hi,
Sorry to use this thread but im also trying to install back to my original Diamond ROM and am currently using the rom developed by Diamond Project (1.93.456.2WWE) and i kept flashing it back using Signed V1.93 RUU and apprently the Diamond project words still keep showing out when i start my phone!
How do i completely remove the Diamond Project thing? Thank you!
Read this............Scroll to Post #39
http://forum.xda-developers.com/showthread.php?t=400950&page=4
band27 said:
Here you go....I did a search
Click to expand...
Click to collapse
I also got that but it's not win32 program... I believe it's running on the Diamond. But I've hard reset, and never able to setup as it's screen was not functioning now...
kawatsu said:
Hi,
Sorry to use this thread but im also trying to install back to my original Diamond ROM and am currently using the rom developed by Diamond Project (1.93.456.2WWE) and i kept flashing it back using Signed V1.93 RUU and apprently the Diamond project words still keep showing out when i start my phone!
How do i completely remove the Diamond Project thing? Thank you!
Click to expand...
Click to collapse
That ROM had a different boot image - so you need to replace that by flashing another splash .NBH file using RUU.
Original splash can be found HERE
and if needed CUSTOM RUU HERE
Just un-zip these and put the splash file in the same folder as the Custom RUU and run the RUU - the flash should take a few seconds and viola - bye bye Diamond project splash.
f810 said:
I've tried to load 1.93 ROM to my diamond but failed on OliNex 1.30. The link in modmydiamond.info on OliNex 1.40 Signed seems not correct, as it's still 1.30 after flashed. I've then flashed UNSIGNED 1.40 OliNex SPL (also downloaded from modmydiamond.info) and now flashing the 1.93 ROM in progress from bootloader.
I will flash the Stock SPL through the Bootloader after that...I hope I can successfully fallback and get it repair...
Last question (I hope), the stock SPL should be 1.37 so I want to confirm whether it can boot 1.93 ROM.
Thanks a lot!
Click to expand...
Click to collapse
I think as long as the SPL is changed and the ROM is of the original language the I think it should be OK to send back like that
f810 said:
you're right. When I flash the Stock SPL, it is "successful" but actually it doesn't update the SPL (i.e yet running OliNex 1.40). Where can I get the Jump SPL?
Click to expand...
Click to collapse
As said before; you should be able to successfully run the stock SPL using RUU - if you are trying this via bootloader it will not work.
Which is the original SPL?? 1.23, 1.34 or 1.37? I do recall taking a picture of the original SPL when i 1st got the Diamond for days like that but i just can't find it now
I'm bought it from Malaysia. Anybody can help me confirm this??
R3PUBL1K said:
As said before; you should be able to successfully run the stock SPL using RUU - if you are trying this via bootloader it will not work.
Click to expand...
Click to collapse
I've tried to connect to ActiveSync successfully although the Initial Setup wizard on my Diamond. I've then run the RUU from RUU-SSPL-withoutNBH.zip and put the stock SPL .NBH file into the extracted directory. It can retrieve my device info, and when I confirm the update of ROM, after 3-5 sec it said about connection failure. I can browse the Internal Storage at the moment yet.
I've then tried similar thing using the Custom RUU inside the package diamond-hspl-1.34.zip. This time I can see 100% update. When I press VolDown and reset, the SPL is still v1.40 ONliEx.
What's wrong with my procedures above?
f810 said:
I've tried to connect to ActiveSync successfully although the Initial Setup wizard on my Diamond. I've then run the RUU from RUU-SSPL-withoutNBH.zip and put the stock SPL .NBH file into the extracted directory. It can retrieve my device info, and when I confirm the update of ROM, after 3-5 sec it said about connection failure. I can browse the Internal Storage at the moment yet.
I've then tried similar thing using the Custom RUU inside the package diamond-hspl-1.34.zip. This time I can see 100% update. When I press VolDown and reset, the SPL is still v1.40 ONliEx.
What's wrong with my procedures above?
Click to expand...
Click to collapse
I think I miss the step of running the SSPL-Manual.exe because of my screen is not responding... Anyway for me to put it into the Windows Startup Folder?? When I use ActiveSync I can't see Windows directory.
Please...please...I miss this step only...
f810 said:
I think I miss the step of running the SSPL-Manual.exe because of my screen is not responding... Anyway for me to put it into the Windows Startup Folder?? When I use ActiveSync I can't see Windows directory.
Please...please...I miss this step only...
Click to expand...
Click to collapse
Can anyone help??

official spl downgrade

can someone tell me, if i can flash officialy some lower version of spl than 0.88?
ftoz said:
can someone tell me, if i can flash officialy some lower version of spl than 0.88?
Click to expand...
Click to collapse
yeah, you can flash Stock SPL Restore 084 or Stock SPL Restore 087 that there at http://forum.xda-developers.com/showpost.php?p=4363807&postcount=1
yeah, but hardspl, relockers and all flom link dont work for me. I have latest rom and spl 0.88, thats seems problem. I try it many times, on many PC, on many cables, on many systems. Dont work. I have only 2 ideas that can help. Downgrade spl with original flasher, but dont know, if exist. Move custom rom to ogiginal flash directory with original ID. I someone has idea to unlock it, please help.
ftoz said:
yeah, but hardspl, relockers and all flom link dont work for me. I have latest rom and spl 0.88, thats seems problem. I try it many times, on many PC, on many cables, on many systems. Dont work. I have only 2 ideas that can help. Downgrade spl with original flasher, but dont know, if exist. Move custom rom to ogiginal flash directory with original ID. I someone has idea to unlock it, please help.
Click to expand...
Click to collapse
Why are you trying to relock?
What are you actually trying to do?
It looks like you've already tried this. If <<< that didn't work, not sure what to tell you mate.
Hi there, first poster so bare with me.
I had problems installing the H-SPL too. Then at last after trying and trying I thought by myself, maybe there could be a version (security) problem using an official 0.88 SPL rom update which doesn't work with the HSPL 0.88 version.
So what I did I looked around for any official ROM update (downgrade) version and also for the official SPL included.
I found the following HTC site (mind the spaces): www.htc.com/uk/help/htc-touch-pro2/#download
So I guess the H-SPL (version 0.88) isn't able to unlock official 0.88 spl's.

Categories

Resources