Help no gsm can flash to any rom without radio - 8525, TyTN, MDA Vario II, JasJam ROM Development

Help
Have read as much info as i can about bricked phone.
Have no radio working shows no gsm on boot
It apears that i can flash to any rom with out a radio, if i flash to one that includes it its stops at 11 - 13% and comes up with an error message 262.
have olipro 2.30 and hardslp7
if i try to flash radiio rom only it wont and stays at 0% until errror message 262
so its a 1a
but not having any luck
please help as this was my dads phone
its an orange spv3100/ herms 100

try reinstalling a stock rom. might work but if you cant install a radio it looks like you have a nice pda but not a phone anymore...

No Not really
The only reason i was having to reflash the phone was that it was locking up all the time, even having flashed the phone it was having problems with Tom Tom.
Please HELLP!

Can some one please advise me on this situation,
is there any way of sorting this out?

stock orange m3100 rom wont flash
Just tried standard orange m3100 rom
it stops at 12% and wont continue,
seems any rom with a radio wont flash past 12/13%
any radio free rom is fine
it wont flash radio only roms
PLEASE HELP

Have you tried flashing radio only?

photoscubaman said:
Just tried standard orange m3100 rom
it stops at 12% and wont continue,
seems any rom with a radio wont flash past 12/13%
any radio free rom is fine
it wont flash radio only roms
PLEASE HELP
Click to expand...
Click to collapse
Have tried radio only roms,
they wont work at all and stays at 0%
have olivpro 2.30 and hardspl7
thought this was ment to prevent bricking?

no, it improves chances of recovering a brick but wont stop it from happening. It loks like your radio is corrupted. You might have to bite the bullet and tell your dad his phone no longer works... sorry for the bad news...

have you tried flashing a rom with radio included through yur sd card. had same issue and this worked for me.

If ya can't install a radio, sounds like your stuck with a pda and not a phone.
Have you tried a number or radio's?
As ultramag69 says
no, it improves chances of recovering a brick but wont stop it from happening. It loks like your radio is corrupted. You might have to bite the bullet and tell your dad his phone no longer works... sorry for the bad news...
Click to expand...
Click to collapse
using hardsplv7 improves chances of recovering, but nothing is 100%
If you flash your phone with manufacturers rom and get everything back to original, see if orange or manufacturer will fix it under warranty or insurance. THIS IS A LAST RESORT AS IF THEY DIG DEEP AND KNOW YOU HAVE MESSED WITH PHONE, THEY'LL DO NOTHING FOR YOU!!!
Personally I have returned phone once due to not being able to receive or make calls. I flashed original rom etc but forgot to put original radio back on. They never noticed and I got my phone back fixed. But this is a BIG RISK.

have now managed to get spl 1.01 on the phone
trying to change to spl 1.04 and reflashing!
however now when i task 32
it has
level FF not Level 0???
any ideas??

shamless bump
Isnt there anybody that can help me?
please

photoscubaman said:
have now managed to get spl 1.01 on the phone
trying to change to spl 1.04 and reflashing!
however now when i task 32
it has
level FF not Level 0???
any ideas??
Click to expand...
Click to collapse
Ditto.
Is there anyway of fixing the corrupted radio? is there no way to "re-write" the radio bootloader?
obviously the radio bootloaders have changed over the different versions of the roms so why cant we "re-construct" the bootloaders in this fashion?
Referring to :HERMES Bootloader 1.01 MFG (WIKI) I cant use the "Flashing SPL-1.04 again" method because my radio is corrupted, so, I lose SuperCID, and don't have access to the lnb command; is there a SPL-1.04.nbS that we can use?!
If there is, would it allow us to use a radio of that version? or is this mute?
I've read several threads and the wiki several times, but, it seems this corrupted radio issue is something new that the wiki's are partially addressing, or, whatever has caused the radio to suddenly become corrupt requires a new method to fix it.
I know i've said I've read the forums, wiki, but perhaps I've missed something? Any assistance is appreciated!

I was wondering if any body had spl 1.04 on their mini sd card?
the method were you just transfer over to the mini card and click on it.
i managed to change my boot loader to version 1.01 this way.
if i can change it to 1.04 can i flash to radio with out it stopping.
thanks

just solved exact problem
Hi
i have been dealing with the same problem for 4.5 hours finally with the help of wiki and pof 's posts i managed to unbrick radio.
first of all i tried almost evceryting. i finally succeed by reseting radio sector. i used mtty to gel into hermes and used commands of one of pof's posts for erasing radio sector.
i dont remember the link but google xda for it. then i flashed tweaked version wich is inclueded in unlocker by pof i aborted the operation in unlocking phase then installed hardspl7
i can use my phone now radio version is 1.10 sth but i didnt tried to install newer radio ( too tired :=) )
i hope it is usefull if anything not clear PM me or write here....
PS:Many many thanx to pof...
bartan

bartan said:
Hi
i have been dealing with the same problem for 4.5 hours finally with the help of wiki and pof 's posts i managed to unbrick radio.
first of all i tried almost evceryting. i finally succeed by reseting radio sector. i used mtty to gel into hermes and used commands of one of pof's posts for erasing radio sector.
i dont remember the link but google xda for it. then i flashed tweaked version wich is inclueded in unlocker by pof i aborted the operation in unlocking phase then installed hardspl7
i can use my phone now radio version is 1.10 sth but i didnt tried to install newer radio ( too tired :=) )
i hope it is usefull if anything not clear PM me or write here....
PS:Many many thanx to pof...
bartan
Click to expand...
Click to collapse
This link you speak of is of high importance!! what were the commands? what was the link?

http://forum.xda-developers.com/archive/index.php/t-280372.html
but after installing radio 1.47 it happened again in one call.
still in square one ....
No SD-card install works (stucks in GSM)
no shipped rom works
i want to ask if there is anyway to erase the whole radio sector ??
rerase command did not work on my hermes may be pof has some solution to this.
bartan

After lots and lots of reading the wiki's and forums over and over again I believe I may have solved the radio corruption problem on my 8525.
Just to let everyone know that I've tried flashing several SPL's; 1.01 MFG, 1.04, 1.10 Oli, 2.10 Oli, 2.60 Oli. Back and forth between the versions but finally I stayed put at 1.10.
I have/had a type 1a brick, but, not from flashing, everything was working great and then it just died. I tried Method 1 of Problem 5: Device shows NO GSM when booting more times then i would like to remember, however, nothing worked. When i tried a Radio only flash it failed at 0% and when i tried a FULL RUU it failed at 12/13% (GSM.nb). Convinced I had a $500 paper weight I got angry tried Method 2 of Problem 5 (see above link) ... strangely on the first try i was able to see the radio (1.40.30.00) and the protocol version as well...
I then thought this was too good to be true and then soft-reset my phone; BAM! "NO GSM".... I tried several times and then finally got the version readouts again... So i soft-reset into bootloader mode
Code:
typed: info 2
returned: HTCS
typed: task 32
returned: Level = 0
typed: rtask b
returned: AT-Command Interpreter ready <--------- YES!!!
I was then able to get enter the AT/Radio Commands so i did what anyone else would do.... FLASH ANOTHER RADIO!!!
I flashed the Radio from HTC_Hermes_SIM_Unlock_v2a and it just finished... I got an error at the end, and after the soft-reset the version stayed 1.40.30.00, but once booted into WM6.1 it immediately picked up the 3G signal... I hope this lasts longer then others have reported.
Should i try to flash another radio that is radio_bootloader 108???

*sigh* ... froze in WM6.1 reset then "No GSM" again... so then i tried HTC_Hermes_SIM_CID_Unlock_v3a but it failed because I kept getting No GSM; so i did the battery trick to get version info's then ran the .bat as instructed and it perfomed the unlock; this time it reflected the radio 1.16.0.0
since I know what it takes to get the radio to flash, i'm trying RUU_Hermes_CINGULAR_WWE_3.62.502.3_6275_1.54.07.00_108_UOOS_SVN05_Ship.exe ..... i mean what do i have to lose right?
[EDIT] it worked... so lets see what happens.... [/EDIT]
[EDIT2] Radio is 1.54.07.00 & Protocol is 32.86u.7020.23H ... so it looks like its perm now... I've been able to send and recieve calls now too.... [/EDIT2]

after several hours of usage, radio no longer responds and WM becomes unstable and after a soft-reset I get "No GSM" ...
Question to Olipro, Des, pof:
Is it possible to log the beginning bootup screen to see what exactly triggers the "No GSM" vs the radio/protocol versions?!?! there has to be something that were missing... it would seem ever since radio 108 this problems have arisen... comments?

Related

URGENT help on Hard SPL screen

Hello,
I executed the Hard SPL cab and went into bootloader or some sort of a multi colored screen which says IPL - 0.50 Trin100 and underneath it says SPL 3.03.0000. It connects to my computer and says USB but when I attempt to flash the new WM6 rom which I just downloaded from the rapidshare it resets the machine and continues to remain on this screen of multi colored stuff. I cannot seem to get out of it no matter what I do. What do i need to do to abort the multi colored screen or allow it to flash my HTC trinity with the Dopod WM6 rom?
Thanks,
Gilbert
PS: please don't shoot me if this was discussed elsewhere. i searched and could not fine anyting
happened to me yesterday.
with this screen install AGAIN the hard....
see
http://forum.xda-developers.com/showthread.php?t=316113
and
http://forum.xda-developers.com/showthread.php?t=312499 -page 45
How? I try to execute again the Hard SPL file and it gives me an error and says close window on PC.
Thanks,
Gilbert
it keeps giving me error in connection and i think i bricked my phone i tried to reinstall several times and i get the same results. Poor me.
Same hapen to me, then ive tried to instal over it a another rom and it came to life.
if you're in the bootloader already, try and run the RUU (update program) again on your pc after reconnecting your device.. if that doesn't work, please give details of the error. I don't think you're bricked yet
racerx_ said:
if you're in the bootloader already, try and run the RUU (update program) again on your pc after reconnecting your device.. if that doesn't work, please give details of the error. I don't think you're bricked yet
Click to expand...
Click to collapse
Thanks for your help. I get Error 260:
The update utility cannot connect to your pda. please check usb is connected. click exit to quit.
When I try to run the upgrade alone in XP it starts at 1% then resets the bootloader.
Thanks,
Gilbert
k which upgrade are you running? still trying to get hard spl working, or running the Dopod WM6 upgrade?
*i've been having some troubles upgrading today too, with the WM6.. scary times ha*
racerx_ said:
k which upgrade are you running? still trying to get hard spl working, or running the Dopod WM6 upgrade?
*i've been having some troubles upgrading today too, with the WM6.. scary times ha*
Click to expand...
Click to collapse
I am trying to upgrade the
RUU_Trinity_DOPODASIA_WWE_3.00.707.17_6275_1.46.00.11_108_Ship but i also tried to reflash the 1.23 HTC rom with GPS to see if it would flash since my device is an HTC trinity and not dopod but the same thing keeps happening.
Try to flash PDAVIET version, my came to life doing this
have you tried to flash any other ROM? I was stuck with the same thing, but managed to flash a cooked ROM..
what's your bootloader showing?
if you fail to flash any other ROM, i think you need to try the stack overfow exploit posted here.. http://forum.xda-developers.com/showthread.php?t=308691&highlight=error+206
it's a bit technical, but i think it's your best bet if all else fails.. Pof might be able to help you over there
No matter what i do, what rom i try to flash i get the same damn error message: Error 260 - Connection!!! I am connected so I don't what is wrong with it. I will try some more then decide to take a hammer and break it into 1000 peices.
Thanks.
racerx_ said:
have you tried to flash any other ROM? I was stuck with the same thing, but managed to flash a cooked ROM..
what's your bootloader showing?
if you fail to flash any other ROM, i think you need to try the stack overfow exploit posted here.. http://forum.xda-developers.com/showthread.php?t=308691&highlight=error+206
it's a bit technical, but i think it's your best bet if all else fails.. Pof might be able to help you over there
Click to expand...
Click to collapse
My bootloader is showing the following:
Trin100
IPL-0.50
Trin100
SPL-3.03.0000
Thanks for all your help.
hmmm... i'm not familiar with that SPL number... unless somehow that got halfway updated with the WM6 update.
I think you better head to that thread and try the stack exploit. Did you try loading a cooked ROM to see what happens?
that is it. i give up. i am not experienced in messing with codes. i am going to retire the device for good and use a regular phone. this is crap. thanks for ur help.
oh, that is the SPL version of the new ROM... i guess you weren't using hard spl when you tried to flash it?
ha, well don't give up too quick.. that's one expensive retired device you've got there.
Just keep cool and you should try to install an official Rom to downgrade this SPL !!
Gilbert said:
I will try some more then decide to take a hammer and break it into 1000 peices.
Thanks.
Click to expand...
Click to collapse
Help!
My bootloader is showing the following:
Trin100
IPL-1.00
Trin100
SPL-9.99.CP
When upgrading with the new released WM6 ROM, it keeps failing at 28%
Please help!
best bet for you, is load a different ROM now. Either cooked or official. That will get your device out of crash-proof spl bootloader.
Once the ROM is loaded, if you want to try the official wm6 again, run SSPL first and see if it'll work for you
p.s. i pm'd you my handphone number in case you've got trouble still..
Gilbert said:
My bootloader is showing the following:
Trin100
IPL-0.50
Trin100
SPL-3.03.0000
Thanks for all your help.
Click to expand...
Click to collapse
Hi Gilbert,
Im having exactly the same problem as you. Right now im in the middle of flashing it back down to WM5 (its working at the moment at 17%).
Hopefully after this i will be able to flash back to WM6 (Most probably will go back to AX3L for now).
Hope this helps you out (im quite stressed about it too!)
Edit: I have just finished flashing to Official WM5, now flashing back to AX3L WM6. It works!

My First Brick..... :eek:

Hi guys. I have installed loads of ROMs onto my trusty hermes yet today, when trying to flash DuttyThroys Ultra Ultra Lite rom this happened: i downloaded ROM and installed it, it seemed to install fine, got to 100% and then came up with error message stating that Image File was corrupt. Now my hermes is stuck on the multicoloured bootloader screen?!?!?!? I have SPL 2.10. Hard SPL V7 HERM 100 IPL 1.04 (Dont know which of these is relevant to anythin?) .I have read the WIKI on repairing bricks but for my problem it says to reflash any nbh without radio. How is this possible if i cant get my pc to connect to my hermes???
Tried the method of turning off usb connection in active sync, removing battery, reconnecting to usb and running mitty (command SET 14 0) but nothing happens. Mitty says CMD error and active sync doesnt reopen the connection like the guide says! Man i hate this cuz i have now become one of those annoying noobs who has bricked their phone and hassles everyone for help!!!!
Have also tried to flash from sd card but nothing happens, flicks to white screen with LOADING... on it for 2 secons then flicks back to that wonderful multicoloured screen of joy!
Any help will be appreciated guys, cant live without my hermes!!!
Welcome to the fuc... nightmare world of the brick,i'mma in your same situation,now my Tytn is a piece of white stone,and it seems there's no reason to bring it back to live!
I can't stay without my Tytn i do a lot of things with it,Skype,SIP calls,Mail,Messenger,Memo,Internet......i'm in totally despair!!!
you should be able to just reflash a known good rom.
hfam95 said:
you should be able to just reflash a known good rom.
Click to expand...
Click to collapse
Brilliant story! both compelling and rich. But i have already explained that my pc doesnt recognise my hermes so how do you RECOMMEND i flash??
IT could be interesting to make the minimal effort to go and read the wiki.
anyway:
http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
Better than just cry.
MarcWhittle said:
Brilliant story! both compelling and rich. But i have already explained that my pc doesnt recognise my hermes so how do you RECOMMEND i flash??
Click to expand...
Click to collapse
With the microsd card...
right, its looking good. managed to begin flashing (bar has stopped for ages but having read this is normal im not so scared!) using the SD method. Where my device wasnt superCID i had to use the matching ROM (Orange) to my CID (which incidently i dont know, just downloaded both Orange ROMs).
While im waiting ill try and help you TETSUO! (Im a noob so probably cant!)
Is your device SuperCID??? tell me as much as you can about your device SPL etc
dude, if u read my post u would have seen that i have tried SD method once (sing Black 3.5 not ORANGE ROM), im not crying and im grateful for any help but when i get advice such as 'flash a rom' im gonna be pissed!
And i have read ALL the page on unbricking!!!
It worked!!
One more question, as i have installed a stock Orange ROM do i now need to reinstall HardSPL v7??
Are you on a Win XP or a Vista PC?
XP dude, sorry should have said! and thanks
i went into bootloader, still says 2.10 olipro but when i try to update to new ROM (Black X RC)and pick autodetect it says it says unknown version, use SSPL. it never used to say this so i assume i need to install HardSPL 7 again???
with the tri colour sceen, when you plug the usb cable in does it go from serial to USB ?
what OS have you got ?
just my 2 cents hope it helps.
dude, i have got past that problem and have managed to install an Orange ROM onto it. i only need to know ow whether to install HardSPL v7 again!
sorry slooooooooooooooooow typing
good question hope there an answer,
MarcWhittle said:
dude, i have got past that problem and have managed to install an Orange ROM onto it. i only need to know ow whether to install HardSPL v7 again!
Click to expand...
Click to collapse
just saw your post if ur device is hardspl you just need to supercid your device, If your spl is still showing hardspl and its coming as a error that normally happens to me as well just manually click spl 2.10 and tick (is it hardspl?}
To recap, i have now managed to flash a stock Orange ROM from SD card ( i think the reason it didnt work first time with SD is because device isnt SuperCID and i was trying to flash Black RC, soon as i used Orange ROM (my device is M3100) it worked. I am now back to a fully operational device. I wish to go back to Black but when i AutoDetect what bootloader i have it recommeds SSPL method. Before all my problems it would always automatically pick 2.10?? Does this mean i need to install HardSPL v7 again??
it was HardSPL v7 before all these problems, but im a noob so dont know if it still is?? would installing Orange ROM from SD Card remove HardSPL?? Bootloader still shows SPL as 2.10 oli
MarcWhittle said:
it was HardSPL v7 before all these problems, but im a noob so dont know if it still is?? would installing Orange ROM from SD Card remove HardSPL?? Bootloader still shows SPL as 2.10 oli
Click to expand...
Click to collapse
If you only flash the orange os.nb only then your hardspl wouldnt have changed so its safe to flash your device just manually choose.
If you want to flash hardspl again then do it on a precaution method
Mark,
First of all well done for getting yourself out of a hole. It seems quite difficult to ask for help these days without being shot to pieces even when you have first tried to help yourself by doing all the right things, which is more than can be said for some who come on here asking for help. So well done again.
Re your question, I would reflash Hard SPL anyway to be sure; however before you do that go to the Mr Vanx's guide on hard SPL (forgot the link but type in www.mrvanx.org and you should be taken there) and follow his instructions.
Good luck.
WB

My Herm200 can ony be flashed to Black Satin

Every other rom that I try either fails at 12% or 82%. I cant use HardSPLv7 or HardSPL. I've reached my the conclusion that my device will for ever be bricked. I started out with a No GSM error and I end up with Black Satin which is really stable but it doesnt help that I have no radio flashed to it. I refuse to cut my loses. Anyone that can be helpful I would greatly appreciate it!!!
Herm200
Black Statin
no radio NoGSM error
IPL-1.04
SPL- 2.10.olipro
Thank you C Brown
Have you tried flashing the HTC Official Rom with radio?
Try flashing back to the official ROM from your carrier...and the flash different ROM
Sounds like the Radio has been corupted.
Have you checked here
http://http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
I'm thinking you need to flash a radio back onto your device. Most if not all of the Cooked Roms recently don't have a Radio included. So, try upgrading the radio. From what I know, flashing a Rom with HardSPL on your device is fairly safe but the Radio is where things can go wrong.
Maybe you should visit the Hermes Upgrading forum and ask the guys there, look at the Sticky's.
I wonder how you lost the Radio? Did you try to upgrade it or did it just disappear?
I bought the phone bricked it had a No GSM error soo I figured I could fix it. Ive been working with wizards for sometime and I've never been able to not recover one. So Ive tried about 4 different radios all of which either fail for error 260 or 262. I've tried from both the os and bootloader. I had schaps newest rom and black satin and both of which ran fine but still no radio. Every OEM base rom I've tried fails at 82% its strange. I've read on other message boards that the only fix is to swap the boards. I dont believe that. I also tried Mtty's set 14 0
task 8 with no avail. I'm thinking if I down grade to WM5 and find a stable radio any radio for that matter and try to work up the ladder back to WM6.
Herm200
IPL-1.04
SPL-2.10.olipro
Black Satin rom
GSM error so no radio
Try using the V3 Unlock then flash it may help.
http://forum.xda-developers.com/showthread.php?t=293665
Also its HTC branded its a straight TYTN its not bound to any carrier. So it should be sim unlocked but hopefully the Cid can be unlocked which could be the hang up during rom and radio changes. Thank you all for you advice all of it will be noted and tried out later today.
So I successfully Flashed Pandora to my phone but still no radio

diamond won't upgrade to 1.93 hspl

I have a gsm diamond (from t-mobile uk) and have flashed it to 1.34 hspl to use the new 25.16 radio and dutty's v3.1 both are working fine however I can't *upgrade* (i know it's not an upgrade per se) to hspl 1.93. it's stuck on 1.34.
using customruu it goes through the normal motions and on screen shows it to 100% then restarts etc, but after i check by going into the bootloader it hasn't updated. I have looked about and search for some time now and don't see anyone expericencing quite the same thing.
any ideas??
paulmurphy777 said:
I have a gsm diamond (from t-mobile uk) and have flashed it to 1.34 hspl to use the new 25.16 radio and dutty's v3.1 both are working fine however I can't *upgrade* (i know it's not an upgrade per se) to hspl 1.93. it's stuck on 1.34.
using customruu it goes through the normal motions and on screen shows it to 100% then restarts etc, but after i check by going into the bootloader it hasn't updated. I have looked about and search for some time now and don't see anyone expericencing quite the same thing.
any ideas??
Click to expand...
Click to collapse
...unfortunately no ideas, just the same problem described here already: http://forum.xda-developers.com/showthread.php?p=2927161#post2927161
paulmurphy777 said:
I have a gsm diamond (from t-mobile uk) and have flashed it to 1.34 hspl to use the new 25.16 radio and dutty's v3.1 both are working fine however I can't *upgrade* (i know it's not an upgrade per se) to hspl 1.93. it's stuck on 1.34.
using customruu it goes through the normal motions and on screen shows it to 100% then restarts etc, but after i check by going into the bootloader it hasn't updated. I have looked about and search for some time now and don't see anyone expericencing quite the same thing.
any ideas??
Click to expand...
Click to collapse
I have the exact same issue... I tired updating it from 1.24 to 1.93 and it restarted like it updated it. But when I go into boot loader its still got the old hardspl.
Does anyone know why??
I have tried searching around for a solution but no luck
I'm no noob and i've flashed 100's of times across many fones and unbricked a few with some careful reading but this seems very odd and stupidly simple. No idea what i'm missing.... only thing i can think to try is to flash from internal storage, but i would think this unwise with the hardspl as I thought hardspl would control access to the internal storage like some sort of bios perhaps?!
Same here
Hey guys,
Does anyone knows what is the resolution for this? I having the same problem as well.
Hi guys!
HSPL blocks write attempts to the SPL-part of the nand! You need to run SSPL from windows mobile and then flash the HSPL-Version you want. This is pretty much the only way to override that write-protection!
cheers
chris
gladiac said:
Hi guys!
HSPL blocks write attempts to the SPL-part of the nand! You need to run SSPL from windows mobile and then flash the HSPL-Version you want. This is pretty much the only way to override that write-protection!
cheers
chris
Click to expand...
Click to collapse
i have almost same problem but the only difference that my Diamond don't have hardspl on it and whenever i try to flash any hardspl phone stops at 0% and stays there for a long time....I want to change my Diamonds language...So can anyone suggest me solution.....I have already posted here on forum but no answer yet!
http://forum.xda-developers.com/showthread.php?t=749664
Another little question that how i can flash hardspl via internal storage and where its root???Root is the device path which we seen as drive in computer when we use mass storage or any other?
gladiac said:
Hi guys!
HSPL blocks write attempts to the SPL-part of the nand! You need to run SSPL from windows mobile and then flash the HSPL-Version you want. This is pretty much the only way to override that write-protection!
cheers
chris
Click to expand...
Click to collapse
Thank you. used this and it worked
Hi everybody,
got yesterday another diamond, after mine died some time ago. It has 193 spl and I cannot upgrade to olinex spl. It runs through everything, but upon reboot it still has the original 193 spl. Any ideas? I really need to flash, mine speaks Dutch and I want it in English. Please help. Kind regards. Ben

[Q] ROM Update stays at 0% - help needed

Dear All,
this time, I have a problem and need your help, please.
I just bought a new (used, but not by me ) HTC Touch Diamond. Hard-SPL (1.37 from whoever) was installed.
First MTTY'ed the device - with success (set 14 0, task 29, task 8)
Wanted to install OliNex 1.40 first
Started ROM-Update, everything went fine, screen of Diamond changed into "bar display" - but stays there with 0%
Tried several flashes (OliNex, ROM, Radio - everything the same)
Does anybody have a hint for me what to do? Identifier seems ok, DIAM100 is shown in intial bootloader screen (three color-screen)
I appreciate any hint.
With kind regards from Switzerland - Christoph
Radio
Downgrade your radio to one below 1.02.XXX before flashing the unlocked radio
Full instructions to unlock your diamond are here
http://forum.xda-developers.com/showthread.php?t=749201
Once you have done this, you can flash any ROM you like
Dear Dave,
thank you very much for your support.
Unfortunately it didn't help but showed everytime the same picture - stuck in the bar at 0% and doesn't do anything.
I tried STEP 1, STEP 2 and downgrading to radio 1.00.25.05 (but actually I don't know which is actually installed, as the Diamond never reaches the Touch Diamond page with ROM & HW Info, it stucks in the Touch Diamond page with no information at all, if started not in Bootloader mode)
It seems to me that the bootloader itself could be corrupted or the model number (shows DIAM100 in Bootloader) is somewhat corrupted, as I know that the internal storage consists of more digits (like DIAM10000 or so) - and a way to fix it with MTTY? But I can't find a description of the MTTY tasks of the Diamond.
Any more Idea?
Thank you Dave, and all the others who read and think, in advance.
X
Can you get into Bootloader mode by holding down
Volume down button + Back button (Bottom right button) + Press reset with the pen
Then keep pressed the first two buttons and let go of reset, keep hold of the first two buttons until it reaches the bootloader mode
If you can do this, then reboot and put the radio onto the storage card (4GB one) and enter bootloader mode, then folllow instructions on that screen to flash the radio, and you can do the same for the rom
It sounds to me like maybe you have not managed to flash the HardSPL properly
Hi Dave!
Thanks for your quick reaction.
Yes, I can anter bootloader mode. But nothing more. Flash is not possible. Hard-SPL was the first thing I tried to flash but it also remained at 0%
How can I put files on the internal storage card from within bootloader mode? (Phone is not booting, ONLY bootloader mode is accessible...) I never encountered this before...
But I can reach the phone with MTTY.. can I access the storage card through this?
X
Have your tried different HardSPL versions ?
Im not sure what is wrong... if you are in Bootloader mode, and the USB drivers are installed and you have activesync running on the PC it should update no problem
I would make sure all the above is true, and attempt different HardSPLs
I think that is the issue as you wont be able to flash an unlocked radio or custom rom without HardSPL being flashed first
Here is another version you could try
http://selfmod.net/how-to-hard-spl-a-htc-diamond/
EDIT - And I dont know if there is a way to access the storage card from MTTY or bootloader, my guess is that you wont be able to
Also, this is a GSM Diamond right ? Not a CDMA ? (UK Networks are GSM)
CDMA flash is here
http://forum.ppcgeeks.com/cdma-diam...ond_c-cdma-sspl-hardspl-package-here-now.html
Hi Dave!
Yes, it's GSM. Thanks for your help and the links provided - it didn't help.
I tried various Hard-SPLs: OliNex 1.20, 1.30, 1.37, 1.40 and 1.93 (developers)
Result - all the same: standstill at 0%
I've seen in MTTY that I have an "upload" menu item - but need there the start address and command line for Diamond plus to know what it is meant for, I will try to find out... and if there is some new know-how out of this, I will post it here, in order that future GENERATIONS may find it *laugh*
Dave? THANKS!
Kindest regards from Switzerland - Christoph
X
Ok, lol Another possible !
Maybe your friend flashed a Signed HardSPL which means you can only flash Signed radios and roms until you flash another unsigned HardSPL
If the Radio you are trying to downgrade to is unsigned that could explain the issue... try and find a Signed radio below version 1.02.XXX and try to flash that, then try to flash to another Unsigned HardSPL, if the radio flash goes ok.
------------
Update stops at 0%
Short answer: You're running the normal HardSPL and you're trying to flash an unsigned (not signed by olinex) ROM. You need the developer version which fixes the 0% issue. Link is at the bottom of this post. Read on to understand the difference between Standard/Developer Edition!
Long answer: First you need to understand that there are two definitions of "signed". HTC and the mobile operators sign ROMs so that the RUU flash utility allows them to be flashed. Usually this is what the word "signed" in the filename means.
Then there is another definition of signed: The developers of HardSPL introduced their own signing process. They want to ensure that people flashing cooked ROMs can rely on a certain quality standard. The normal version of HardSPL will only allow ROMs signed by OliNex to be flashed. If the ROM you are about to flash is signed, it will say so in the thread you got it from. If it isn't signed, you will need the developer version of HardSPL. That one will allow any ROM to be flashed. Get it at the bottom of this posting.
A note on this: The signing process by olinex makes sure that the ROM you're about to flash won't brick your device. It doesn't mean all other ROMs are necessarily evil.
-----------
Some help on 0% flash hangs
http://forum.xda-developers.com/showthread.php?t=409425
I`ll have a look into uploading from MTTY as I have never tried that.. sounds a good feature if you can though for dead phones and such !
good luck.. again lol
magicdave26 said:
Ok, lol Another possible !
Maybe your friend flashed a Signed HardSPL which means you can only flash Signed radios and roms until you flash another unsigned HardSPL
If the Radio you are trying to downgrade to is unsigned that could explain the issue... try and find a Signed radio below version 1.02.XXX and try to flash that, then try to flash to another Unsigned HardSPL, if the radio flash goes ok.
------------
Update stops at 0%
Short answer: You're running the normal HardSPL and you're trying to flash an unsigned (not signed by olinex) ROM. You need the developer version which fixes the 0% issue. Link is at the bottom of this post. Read on to understand the difference between Standard/Developer Edition!
Long answer: First you need to understand that there are two definitions of "signed". HTC and the mobile operators sign ROMs so that the RUU flash utility allows them to be flashed. Usually this is what the word "signed" in the filename means.
Then there is another definition of signed: The developers of HardSPL introduced their own signing process. They want to ensure that people flashing cooked ROMs can rely on a certain quality standard. The normal version of HardSPL will only allow ROMs signed by OliNex to be flashed. If the ROM you are about to flash is signed, it will say so in the thread you got it from. If it isn't signed, you will need the developer version of HardSPL. That one will allow any ROM to be flashed. Get it at the bottom of this posting.
A note on this: The signing process by olinex makes sure that the ROM you're about to flash won't brick your device. It doesn't mean all other ROMs are necessarily evil.
-----------
Some help on 0% flash hangs
http://forum.xda-developers.com/showthread.php?t=409425
I`ll have a look into uploading from MTTY as I have never tried that.. sounds a good feature if you can though for dead phones and such !
good luck.. again lol
Click to expand...
Click to collapse
This is the answer. I used to have the same problem because when I bought my diamond I thought everything runs the same as the TyTN but ...
So to cut this story short, almost 90% of the 0% bar situations are because U R not using signed roms. However if Ya want to then use the unsigned HardSPL.
Hi Dave & Nazgul,
it seems that my case belonst to the non-90%
Of course I tried all this, but I have THREE diamonds - two were branded by the Swiss Swisscom (this is, in fact, the same image as the German Vodafone branding), one was the original HTC version
I'm flashing Diamonds since two years though.
My fault this time was, that I THOUGHT, this new one were HardSPL'ed, but it wasn't - and formatted the device using MTTY without Hard-SPL.
After that I had the above mentioned situation.
NO Hard-SPL was flashable - as written above - also noth the unsigned developer 1.93 edition - it always remained at 0%
I managed in the meantime to flash the original Vodafone/Swisscom ROM. So I have back the device in the official configuration (HTC Swisscom 1.97 package http://www.swisscom-mobile.ch/scm/d...pa=0x0x147x18x0x0x0x0x0&odg=SoftwareAndManual)
But - this uses Radio 1.08.xxx and I would like to downgrade because I think, Dave's hint above to use a radio before 1.02.xxx would be worth a try.
BUT - I STILL can't flash anything. Neither ANY Hard-SPL nor any Radio version nor any ROM.
The bar remains at 0%
I tried to find the original (first edition) of the Swisscom ROM Package, which used the Radio 1.00.25.05 - and then to try Dave's proposed steps.. but I can't find it anymore - all you can find is the "latest" package...
So I would still appreciate any help to be able to flash. Ok, now at least, I have a usable phone... but... I wanted to use it (as the other two) for ROM development testing, so who wants to have a PHONE!?!?
Kind regards from Switzerland - Christoph
Here is your radios
Sorry for the short post, I have a really bad hangover lol
http://forum.xda-developers.com/showthread.php?t=407956
Morn' Dave!
I tried them all - none of them was flashable... same 0%-bar.
I thought of having the V 1.00 complete official Swisscom-Pack and as part of it, the radio 1.00.25.05, which is included. Seems to me, that the c(complete) official ROM pack is flashable.
THEN I could re-try to flash Hard-SPL (with then installed radio below 1.02.xxx)
Hangover? What's this?
Christoph21x said:
Morn' Dave!
I tried them all - none of them was flashable... same 0%-bar.
I thought of having the V 1.00 complete official Swisscom-Pack and as part of it, the radio 1.00.25.05, which is included. Seems to me, that the c(complete) official ROM pack is flashable.
THEN I could re-try to flash Hard-SPL (with then installed radio below 1.02.xxx)
Hangover? What's this?
Click to expand...
Click to collapse
YEa that might work, it is almost certain the issue is the HARDSpl being either not flashed, or flashed with a signed version
Good luck !!
And the hangover is nearly gone... I cured yesterdays with more alcohol lol
Have you tried these UNSIGNED dev HARDspls ?
http://forum.xda-developers.com/showthread.php?t=400950
Hi Dave - GOT IT, solved
The "secret" was to flash noit from withi boot loader but from within Win Mobile with ActiveSync/Windows Device Center connected.
Then say "Yes" when "enterbootloader.exe" was asked to be installed/invoked.
Then the Device rebooted, flashed Hrd-SPL 1.40 correctly - and everything else onwards went fine.
Thanks a lot for your assitance, Dave and others.
Kind regards from Switzerland - Christoph
Ah.. I thought you were already using the Activesync and CustomRUU to flash it with !
Yes, the ROMs and Radios can be flashed from the storage card, but the Hard SPL needs to be done from Activesync / CUstomRUU
Pleased you got it working anyway

Categories

Resources