Related
Hi guys. I have installed loads of ROMs onto my trusty hermes yet today, when trying to flash DuttyThroys Ultra Ultra Lite rom this happened: i downloaded ROM and installed it, it seemed to install fine, got to 100% and then came up with error message stating that Image File was corrupt. Now my hermes is stuck on the multicoloured bootloader screen?!?!?!? I have SPL 2.10. Hard SPL V7 HERM 100 IPL 1.04 (Dont know which of these is relevant to anythin?) .I have read the WIKI on repairing bricks but for my problem it says to reflash any nbh without radio. How is this possible if i cant get my pc to connect to my hermes???
Tried the method of turning off usb connection in active sync, removing battery, reconnecting to usb and running mitty (command SET 14 0) but nothing happens. Mitty says CMD error and active sync doesnt reopen the connection like the guide says! Man i hate this cuz i have now become one of those annoying noobs who has bricked their phone and hassles everyone for help!!!!
Have also tried to flash from sd card but nothing happens, flicks to white screen with LOADING... on it for 2 secons then flicks back to that wonderful multicoloured screen of joy!
Any help will be appreciated guys, cant live without my hermes!!!
Welcome to the fuc... nightmare world of the brick,i'mma in your same situation,now my Tytn is a piece of white stone,and it seems there's no reason to bring it back to live!
I can't stay without my Tytn i do a lot of things with it,Skype,SIP calls,Mail,Messenger,Memo,Internet......i'm in totally despair!!!
you should be able to just reflash a known good rom.
hfam95 said:
you should be able to just reflash a known good rom.
Click to expand...
Click to collapse
Brilliant story! both compelling and rich. But i have already explained that my pc doesnt recognise my hermes so how do you RECOMMEND i flash??
IT could be interesting to make the minimal effort to go and read the wiki.
anyway:
http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
Better than just cry.
MarcWhittle said:
Brilliant story! both compelling and rich. But i have already explained that my pc doesnt recognise my hermes so how do you RECOMMEND i flash??
Click to expand...
Click to collapse
With the microsd card...
right, its looking good. managed to begin flashing (bar has stopped for ages but having read this is normal im not so scared!) using the SD method. Where my device wasnt superCID i had to use the matching ROM (Orange) to my CID (which incidently i dont know, just downloaded both Orange ROMs).
While im waiting ill try and help you TETSUO! (Im a noob so probably cant!)
Is your device SuperCID??? tell me as much as you can about your device SPL etc
dude, if u read my post u would have seen that i have tried SD method once (sing Black 3.5 not ORANGE ROM), im not crying and im grateful for any help but when i get advice such as 'flash a rom' im gonna be pissed!
And i have read ALL the page on unbricking!!!
It worked!!
One more question, as i have installed a stock Orange ROM do i now need to reinstall HardSPL v7??
Are you on a Win XP or a Vista PC?
XP dude, sorry should have said! and thanks
i went into bootloader, still says 2.10 olipro but when i try to update to new ROM (Black X RC)and pick autodetect it says it says unknown version, use SSPL. it never used to say this so i assume i need to install HardSPL 7 again???
with the tri colour sceen, when you plug the usb cable in does it go from serial to USB ?
what OS have you got ?
just my 2 cents hope it helps.
dude, i have got past that problem and have managed to install an Orange ROM onto it. i only need to know ow whether to install HardSPL v7 again!
sorry slooooooooooooooooow typing
good question hope there an answer,
MarcWhittle said:
dude, i have got past that problem and have managed to install an Orange ROM onto it. i only need to know ow whether to install HardSPL v7 again!
Click to expand...
Click to collapse
just saw your post if ur device is hardspl you just need to supercid your device, If your spl is still showing hardspl and its coming as a error that normally happens to me as well just manually click spl 2.10 and tick (is it hardspl?}
To recap, i have now managed to flash a stock Orange ROM from SD card ( i think the reason it didnt work first time with SD is because device isnt SuperCID and i was trying to flash Black RC, soon as i used Orange ROM (my device is M3100) it worked. I am now back to a fully operational device. I wish to go back to Black but when i AutoDetect what bootloader i have it recommeds SSPL method. Before all my problems it would always automatically pick 2.10?? Does this mean i need to install HardSPL v7 again??
it was HardSPL v7 before all these problems, but im a noob so dont know if it still is?? would installing Orange ROM from SD Card remove HardSPL?? Bootloader still shows SPL as 2.10 oli
MarcWhittle said:
it was HardSPL v7 before all these problems, but im a noob so dont know if it still is?? would installing Orange ROM from SD Card remove HardSPL?? Bootloader still shows SPL as 2.10 oli
Click to expand...
Click to collapse
If you only flash the orange os.nb only then your hardspl wouldnt have changed so its safe to flash your device just manually choose.
If you want to flash hardspl again then do it on a precaution method
Mark,
First of all well done for getting yourself out of a hole. It seems quite difficult to ask for help these days without being shot to pieces even when you have first tried to help yourself by doing all the right things, which is more than can be said for some who come on here asking for help. So well done again.
Re your question, I would reflash Hard SPL anyway to be sure; however before you do that go to the Mr Vanx's guide on hard SPL (forgot the link but type in www.mrvanx.org and you should be taken there) and follow his instructions.
Good luck.
WB
Hello to anyone who can help me...
i am posting this thread after searching this forum for answers to my problem, and i could not find the answers...
I have the Diamond (DIAM100) with Original SPL 1.37.000 and GER Stock Rom installed.
My Upgrade goal is HardSPL 1.38 Signed (Olinex) / DiamondProject V2 GER / radio .05
I try to upgrade SPL, Radio and Rom according to several guides in this forum, but nothing seems to work for me.
I tried using the RUU Program with HardSPL, tried Diamond CustomRUU, tried manual Bootloader access, everytime the Upgrade Software stays at 0% (on the phone also) and after about 5 minutes i get ERROR [262].
Luckily, i haven't bricked my diamond yet, it always came back to life again.
i can confirm, that the device enters bootloader mode, then changes to grey screen with progress bar. But that is all.
Maybe it is a Vista issue, maybe not.
But all i get is ERROR [262]: Update Error
Suggestions, anyone?
Thanks in advance for any serious help...
______________________________________
HTC TD DIAM100
MDA Compact I (Magician, unmodified)
MDA VarioII (Hermes, running Schaps 3.54GER, thanks Schaps great ROM)
I get EXACTLY the same... i've tried everything (except a hammer) to fix it.
I'm running
Rom: 1.37.707.1 wwe
Radio: 1.00.25.03
Proto: 52.26a.25.09h
I'm also using Vista 32
(all fresh out of the HTC box)
http://forum.xda-developers.com/showthread.php?p=2338991
Are you running Vista X64 coz i had the same error in it ..
try to flash it with xp!
udayrulz said:
Are you running Vista X64 coz i had the same error in it ..
Click to expand...
Click to collapse
... Running Vista Ultimate 32bit, but not sure if that will make a difference...
I will try to get hands on XP computer tonite....
You can always try running the RUU update utility in WinXP32 compat mode.
What Hard SPL ar eyou using???.... usually the problem...
you will need Developer edition if the ROM is not signed.
developer edition worked for me on Vista 32. Thanks guys!
OK
I ran a Hard-SPL (from the dev thread) Diamond-OliNex
This completed and did whatever it did and i had to do the basic setup on the phone again.
I have now got the radio ending .06 from this thread this thread and cant get it to work with the OilNex Hard SPL or the 1.34 listed in that thread.
I'm back to square one where Error 262 Update error is occuring.
I'm tring to flash the radio as the O/S i have appears to be running sweet but its having web issues that appear to be DNS/Connection related.
This needs an idiots guide like the other phones have .... 'coz i'm an idiot and I can't do it.
Monty Burns said:
OK
I ran a Hard-SPL (from the dev thread) Diamond-OliNex
This completed and did whatever it did and i had to do the basic setup on the phone again.
I have now got the radio ending .06 from this thread this thread and cant get it to work with the OilNex Hard SPL or the 1.34 listed in that thread.
I'm back to square one where Error 262 Update error is occuring.
I'm tring to flash the radio as the O/S i have appears to be running sweet but its having web issues that appear to be DNS/Connection related.
This needs an idiots guide like the other phones have .... 'coz i'm an idiot and I can't do it.
Click to expand...
Click to collapse
Yeah, but for me the problem still is to get ANY HardSPL on the Diamond in the first place.
I was trying to put HardSPL 1.38_Signed to the phone...
Adwinp: thanks for the advice, but did not work either...
As far as i can tell, this may be a problem with the USB driver from the Windows mobility center software...
I will try on real XP and give you feedback tomorrow.
thanks guys.
Doctor_Who said:
...
I was trying to put HardSPL 1.38_Signed to the phone...
...
Click to expand...
Click to collapse
The developer edition i.e. unsigned worked for me.
I am currently going through the stages in the wiki VERY closely. Dont know if they will work :/
Doctor_Who said:
Hello to anyone who can help me...
i am posting this thread after searching this forum for answers to my problem, and i could not find the answers...
I have the Diamond (DIAM100) with Original SPL 1.37.000 and GER Stock Rom installed.
My Upgrade goal is HardSPL 1.38 Signed (Olinex) / DiamondProject V2 GER / radio .05
I try to upgrade SPL, Radio and Rom according to several guides in this forum, but nothing seems to work for me.
I tried using the RUU Program with HardSPL, tried Diamond CustomRUU, tried manual Bootloader access, everytime the Upgrade Software stays at 0% (on the phone also) and after about 5 minutes i get ERROR [262].
Luckily, i haven't bricked my diamond yet, it always came back to life again.
i can confirm, that the device enters bootloader mode, then changes to grey screen with progress bar. But that is all.
Maybe it is a Vista issue, maybe not.
But all i get is ERROR [262]: Update Error
Suggestions, anyone?
Thanks in advance for any serious help...
______________________________________
HTC TD DIAM100
MDA Compact I (Magician, unmodified)
MDA VarioII (Hermes, running Schaps 3.54GER, thanks Schaps great ROM)
Click to expand...
Click to collapse
I had the exact same problems. I tried every possible combination of Hard SPL and ROMs. Here is what worked for me in the end (no problems since):
1. install newest .Net 3.5 on windows PC (don't know if this has anything to do with my problems but after installing everything started working fine)
2. install Unsigned HardSPL (developer edition): http://forum.xda-developers.com/showthread.php?t=400950
3. install chosen ROM / Radio ROM with RUU (Rom Updater Utility): http://forum.xda-developers.com/showthread.php?t=396073
After flashing a ROM the device makes a hard reset so you should backup your data first! http://forum.xda-developers.com/showthread.php?t=299705
good luck!
Finally it worked, also thanks to all who replied in this thread.
So i like to share my experience in this:
1. first i downloaded all SPL and Radio i could find, then i looked for GER language Rom. Quickly decided for DPT V2.
2. First attempt to flash failed completely on a Vista PC (32 Bit Ultimate)
3. Back home, moved all the downloaded files to my XP SP2 PC..
4. Noticed: DiamondCustomRUU would not start in XP, got error message saying "... could not be initialized", so i tried the standard RUU instead, with the shortcut of manually putting the PDA into Bootloader mode...
5. Sucessfully flashed HardSPL 1.38 on the Diamond, and the device rebooted with Hard reset.
6. Next i tried to upgrade Radio to .05 Version... Failed, stuck a 0%
7. Changed SPL to 1.40 (Unsigned), now the Radio could be flashed. Seems that Radio Files are Unsigned?
8. Flashed DPT V2. Success.
But still wondered about the unsigned Radio file...
Again, thank you all
-------------
Hello i have a HTC orange Touch Diamond and i want to update the ROM as it is terrible. I am not that technical. can someone please explain what i need to do from scratch.
Thank you
I suggest your search the forum...
hello newbie
yes use the search button...it works really well
You first need to flash your diamond with one of the hard spl on this site and after you've done that you can take your pick from any of the roms on here
sorry guys i did look just didnt understand much. I am trying to use Hard SPL just cant get it to work.
same here
I have an orange htc Diamond and would really apreciate which files wouldwork. Everything I have tried stay's at Zero and ends up in an error.
Any help would be greatly ppreciated
root directory
to use hard spl i have to put a file in the root directory! but what is the root directory?
Hi James, your failing at 0% most likely because the SPL your using will not allow unsigned ROM's. Look for another SPL, one with developer edition in the title is good and works quite well for me.
I have an Orange also, the first thing to do is install the SPL then flash the radio (.05 is good) then get a new ROM!
Hope this helps
i think i broke my phone!!!!!
lol
i put the 2 files sspl and jump into my Diamond then i run sspl from my diamond and my phone resets.
The background image flashs a bit now. I still cant update the ROM and ideas what im doing wrong?
james soules said:
i think i broke my phone!!!!!
lol
i put the 2 files sspl and jump into my Diamond then i run sspl from my diamond and my phone resets.
The background image flashs a bit now. I still cant update the ROM and ideas what im doing wrong?
Click to expand...
Click to collapse
You need to do the following
1. Download the Unsigned HardSPL 1.24 from here http://forum.xda-developers.com/showthread.php?t=408621 and extract to a folder on your PC. Make sure you have Active sync installed and setup with your Diamond. Run the Updater in the 1.24 folder. Once the Phone reboots reconnect with active sync.
2. Download any of the ROMS on here and run the ROM to flash the phone.
Thats it !!!!!
Topboy
as i go to add a ROM i get a error saying the application failed to initialize properly ( 0xc0000135) click OK to terminate
Or check www.modmydiamond.info for easy to understand information
i get the above error as i try to add RUU
Hard SPL won't work
Hello,
From what I've read on the forum and also on www.modmydiamond.info, I gather I need to go through the Hard SPL step before installing any ROM.
However, after trying 2 different SPLs (hard_spl.120 and diamond_hspl_1.24) it still doesn't work.
I'm stuck at 0%.
Thanks
Read here....
As an alternative to the other threads try this one:
http://forum.xda-developers.com/showthread.php?t=416211
Its about the most comprehensive writeup I've seen to quickly and easily get your Diamond set from HardSPL to Radios to ROM's
Also read the WiKi's section at the top of the forum......
Query on Orange htc Upgrade ROM.
Hi There,
I have recently purchased a htc diamond, it was originally an Orange unit but is unblocked.The ROM version is 1.37 but I wish to flash to 1.93.I have the Orange released version of the 1.93 as htc wont support me direct.Question is, if I do this will the unit revert back to being Orange??ie.....does this flash the radio back?? or will it remained unblocked??
Thanks in advance...
james soules said:
Hello i have a HTC orange Touch Diamond and i want to update the ROM as it is terrible. I am not that technical. can someone please explain what i need to do from scratch.
Thank you
Click to expand...
Click to collapse
thxthxthxthx
So as you can figure out from the thread title I have a problem flashing my htc diamond.
I have installed a HardSPL version 1.30 OliNex, I can confirm that becouse on the three color screen there is a text saying "1.30 OliNex".
I still have the original ROM that comes with the phone when I bought it, so this meant to be my first flashing.
I want to flash the phone with this rom http://forum.xda-developers.com/showthread.php?t=593678 it is a WM 6.5 based ROM.
Because in the ROM package there wasn't a ROMUpdateUtility.exe I used it from other ROM package.
Connected via ActiveSync and followed the wizard. The phone reset and there came a gray screen with a progress bar. Now both progress bars on the phone and on the PC screen remain 0% and after a wile RUU finished with 262 ERROR Connection error, see the attached picture.
After that I tried to flash it from Internal Storage. A followed the steps according the procedure, and after the three colored screen it came the gray screen with "Loading..." message. I waited for almost 30 minutes and nothing happened.
What seems to be the problem?
I assumed about firewall disabling the connection. But I turned off the firewall and again the same story.
Then somewhere I found that there is incompatibility with the RUU and HardSPL version, but tried to flash with the same RUU that I used when I was installing HardSPL.
Then I tough that the problem is about flashing unsigned ROM on a signed HSPL, but it is not that the ROM is signed.
I am afraid to use MTTY so I don't brick my phone, because this is my first time flashing a Diamond.
I'm confused What seems to be the problem?
Any help can be welcomed.
Could this be indication of a hardware problem? When waiting for the "Loading..." message disappear the back cover warms a little.
Thanks.
1. Did you use the RUU from my thread?
2. NEVER USE AN H-SPL RUU TO FLASH ANYTHING OTHER THAN H-SPL!
3. is this a CMDA phone. IE, what network are you on?
Well no I didn't use the RUU from your thread, I've used a RUU from other ROM package.
This is not a CDMA phone I'm on T-Mobile Macedonia network. And the phone looks like this
On other Macedonian forum they told me it is a hardware problem. Can this be true?
So what do you think about my problem?
Well no I didn't use the RUU from your thread, I've used a RUU from other ROM package.
This is not a CDMA phone I'm on T-Mobile Macedonia network. And the phone looks like this
On other Macedonian forum they told me it is a hardware problem. Can this be true?
So what do you think about my problem?
EDIT: I did tried the RUU you recommended in your thread but it's the same.
I think it is in the PDA.
Configure active sync, and uncheck "allow usb connection" and try again.
For updating from internal storage you must have to copy the rom to the root of internal storage with a special name, ""diamimg.nbh"
Hmmm..
What he said... and...
Should have used one of the earlier SPLs. you only need to use the latest one if you are having problems with the older versions. I have the same diamond and used an early SPL.
Upgrade the radio rom first and go with a rom that's version 6.1 not 6.5 as most 6.5 roms now pack the Sense application.. (IMO Non-Sense, Senseless (Not enought ram or responsiveness))
Old roms here
http://forum.xda-developers.com/showthread.php?t=470757
Give olinex some cash for his Diamond Unlocker as this is the surefire way to fix it.
johnyboy_ said:
Configure active sync, and uncheck "allow usb connection" and try again.
For updating from internal storage you must have to copy the rom to the root of internal storage with a special name, ""diamimg.nbh"
Click to expand...
Click to collapse
The connection between PC and PDA is made, because as I said there is a progress bar on the phone screen too.
djfuego said:
What he said... and...
Should have used one of the earlier SPLs. you only need to use the latest one if you are having problems with the older versions. I have the same diamond and used an early SPL.
Upgrade the radio rom first and go with a rom that's version 6.1 not 6.5 as most 6.5 roms now pack the Sense application.. (IMO Non-Sense, Senseless (Not enought ram or responsiveness))
Old roms here
http://forum.xda-developers.com/showthread.php?t=470757
Give olinex some cash for his Diamond Unlocker as this is the surefire way to fix it.
Click to expand...
Click to collapse
As I understand you, you are saying to install later version of Hard SPL right?
So to install a new version of Hard SPL I just need to do the same procedure as the first time, or I have to uninstall the previous one?
And please help me which version of Hard SPL is safest to install? I'm afraid of the developer versions or maybe they aren't so scary
Are you a 100% positive it is the HardSPL?
djandreski said:
And please help me which version of Hard SPL is safest to install? I'm afraid of the developer versions or maybe they aren't so scary
Are you a 100% positive it is the HardSPL?
Click to expand...
Click to collapse
Presuming from your post, you are using a signed Olinex SPL, i doubt that the rom has been signed be OliNex, the only difference with Dev is you can flash any Rom, flash the Dev one from my thread, nothing to be afraid of
Good Luck
Badwolve1
What are the steps of installing new SPL?
Do I just need to do the same procedure as the first time, or I have to uninstall the previous one(somehow)?
UPDATE: I did it, I successfully flashed my Diamond PDA! It seams that the problem was in the SPL I installed 1.40 OliNex Unsigned and it flashed like a charm. Thanks guys for the help. Now this thread can be closed, or do I have to close it myself.
Great!
Glad it all worked out
Dear All,
this time, I have a problem and need your help, please.
I just bought a new (used, but not by me ) HTC Touch Diamond. Hard-SPL (1.37 from whoever) was installed.
First MTTY'ed the device - with success (set 14 0, task 29, task 8)
Wanted to install OliNex 1.40 first
Started ROM-Update, everything went fine, screen of Diamond changed into "bar display" - but stays there with 0%
Tried several flashes (OliNex, ROM, Radio - everything the same)
Does anybody have a hint for me what to do? Identifier seems ok, DIAM100 is shown in intial bootloader screen (three color-screen)
I appreciate any hint.
With kind regards from Switzerland - Christoph
Radio
Downgrade your radio to one below 1.02.XXX before flashing the unlocked radio
Full instructions to unlock your diamond are here
http://forum.xda-developers.com/showthread.php?t=749201
Once you have done this, you can flash any ROM you like
Dear Dave,
thank you very much for your support.
Unfortunately it didn't help but showed everytime the same picture - stuck in the bar at 0% and doesn't do anything.
I tried STEP 1, STEP 2 and downgrading to radio 1.00.25.05 (but actually I don't know which is actually installed, as the Diamond never reaches the Touch Diamond page with ROM & HW Info, it stucks in the Touch Diamond page with no information at all, if started not in Bootloader mode)
It seems to me that the bootloader itself could be corrupted or the model number (shows DIAM100 in Bootloader) is somewhat corrupted, as I know that the internal storage consists of more digits (like DIAM10000 or so) - and a way to fix it with MTTY? But I can't find a description of the MTTY tasks of the Diamond.
Any more Idea?
Thank you Dave, and all the others who read and think, in advance.
X
Can you get into Bootloader mode by holding down
Volume down button + Back button (Bottom right button) + Press reset with the pen
Then keep pressed the first two buttons and let go of reset, keep hold of the first two buttons until it reaches the bootloader mode
If you can do this, then reboot and put the radio onto the storage card (4GB one) and enter bootloader mode, then folllow instructions on that screen to flash the radio, and you can do the same for the rom
It sounds to me like maybe you have not managed to flash the HardSPL properly
Hi Dave!
Thanks for your quick reaction.
Yes, I can anter bootloader mode. But nothing more. Flash is not possible. Hard-SPL was the first thing I tried to flash but it also remained at 0%
How can I put files on the internal storage card from within bootloader mode? (Phone is not booting, ONLY bootloader mode is accessible...) I never encountered this before...
But I can reach the phone with MTTY.. can I access the storage card through this?
X
Have your tried different HardSPL versions ?
Im not sure what is wrong... if you are in Bootloader mode, and the USB drivers are installed and you have activesync running on the PC it should update no problem
I would make sure all the above is true, and attempt different HardSPLs
I think that is the issue as you wont be able to flash an unlocked radio or custom rom without HardSPL being flashed first
Here is another version you could try
http://selfmod.net/how-to-hard-spl-a-htc-diamond/
EDIT - And I dont know if there is a way to access the storage card from MTTY or bootloader, my guess is that you wont be able to
Also, this is a GSM Diamond right ? Not a CDMA ? (UK Networks are GSM)
CDMA flash is here
http://forum.ppcgeeks.com/cdma-diam...ond_c-cdma-sspl-hardspl-package-here-now.html
Hi Dave!
Yes, it's GSM. Thanks for your help and the links provided - it didn't help.
I tried various Hard-SPLs: OliNex 1.20, 1.30, 1.37, 1.40 and 1.93 (developers)
Result - all the same: standstill at 0%
I've seen in MTTY that I have an "upload" menu item - but need there the start address and command line for Diamond plus to know what it is meant for, I will try to find out... and if there is some new know-how out of this, I will post it here, in order that future GENERATIONS may find it *laugh*
Dave? THANKS!
Kindest regards from Switzerland - Christoph
X
Ok, lol Another possible !
Maybe your friend flashed a Signed HardSPL which means you can only flash Signed radios and roms until you flash another unsigned HardSPL
If the Radio you are trying to downgrade to is unsigned that could explain the issue... try and find a Signed radio below version 1.02.XXX and try to flash that, then try to flash to another Unsigned HardSPL, if the radio flash goes ok.
------------
Update stops at 0%
Short answer: You're running the normal HardSPL and you're trying to flash an unsigned (not signed by olinex) ROM. You need the developer version which fixes the 0% issue. Link is at the bottom of this post. Read on to understand the difference between Standard/Developer Edition!
Long answer: First you need to understand that there are two definitions of "signed". HTC and the mobile operators sign ROMs so that the RUU flash utility allows them to be flashed. Usually this is what the word "signed" in the filename means.
Then there is another definition of signed: The developers of HardSPL introduced their own signing process. They want to ensure that people flashing cooked ROMs can rely on a certain quality standard. The normal version of HardSPL will only allow ROMs signed by OliNex to be flashed. If the ROM you are about to flash is signed, it will say so in the thread you got it from. If it isn't signed, you will need the developer version of HardSPL. That one will allow any ROM to be flashed. Get it at the bottom of this posting.
A note on this: The signing process by olinex makes sure that the ROM you're about to flash won't brick your device. It doesn't mean all other ROMs are necessarily evil.
-----------
Some help on 0% flash hangs
http://forum.xda-developers.com/showthread.php?t=409425
I`ll have a look into uploading from MTTY as I have never tried that.. sounds a good feature if you can though for dead phones and such !
good luck.. again lol
magicdave26 said:
Ok, lol Another possible !
Maybe your friend flashed a Signed HardSPL which means you can only flash Signed radios and roms until you flash another unsigned HardSPL
If the Radio you are trying to downgrade to is unsigned that could explain the issue... try and find a Signed radio below version 1.02.XXX and try to flash that, then try to flash to another Unsigned HardSPL, if the radio flash goes ok.
------------
Update stops at 0%
Short answer: You're running the normal HardSPL and you're trying to flash an unsigned (not signed by olinex) ROM. You need the developer version which fixes the 0% issue. Link is at the bottom of this post. Read on to understand the difference between Standard/Developer Edition!
Long answer: First you need to understand that there are two definitions of "signed". HTC and the mobile operators sign ROMs so that the RUU flash utility allows them to be flashed. Usually this is what the word "signed" in the filename means.
Then there is another definition of signed: The developers of HardSPL introduced their own signing process. They want to ensure that people flashing cooked ROMs can rely on a certain quality standard. The normal version of HardSPL will only allow ROMs signed by OliNex to be flashed. If the ROM you are about to flash is signed, it will say so in the thread you got it from. If it isn't signed, you will need the developer version of HardSPL. That one will allow any ROM to be flashed. Get it at the bottom of this posting.
A note on this: The signing process by olinex makes sure that the ROM you're about to flash won't brick your device. It doesn't mean all other ROMs are necessarily evil.
-----------
Some help on 0% flash hangs
http://forum.xda-developers.com/showthread.php?t=409425
I`ll have a look into uploading from MTTY as I have never tried that.. sounds a good feature if you can though for dead phones and such !
good luck.. again lol
Click to expand...
Click to collapse
This is the answer. I used to have the same problem because when I bought my diamond I thought everything runs the same as the TyTN but ...
So to cut this story short, almost 90% of the 0% bar situations are because U R not using signed roms. However if Ya want to then use the unsigned HardSPL.
Hi Dave & Nazgul,
it seems that my case belonst to the non-90%
Of course I tried all this, but I have THREE diamonds - two were branded by the Swiss Swisscom (this is, in fact, the same image as the German Vodafone branding), one was the original HTC version
I'm flashing Diamonds since two years though.
My fault this time was, that I THOUGHT, this new one were HardSPL'ed, but it wasn't - and formatted the device using MTTY without Hard-SPL.
After that I had the above mentioned situation.
NO Hard-SPL was flashable - as written above - also noth the unsigned developer 1.93 edition - it always remained at 0%
I managed in the meantime to flash the original Vodafone/Swisscom ROM. So I have back the device in the official configuration (HTC Swisscom 1.97 package http://www.swisscom-mobile.ch/scm/d...pa=0x0x147x18x0x0x0x0x0&odg=SoftwareAndManual)
But - this uses Radio 1.08.xxx and I would like to downgrade because I think, Dave's hint above to use a radio before 1.02.xxx would be worth a try.
BUT - I STILL can't flash anything. Neither ANY Hard-SPL nor any Radio version nor any ROM.
The bar remains at 0%
I tried to find the original (first edition) of the Swisscom ROM Package, which used the Radio 1.00.25.05 - and then to try Dave's proposed steps.. but I can't find it anymore - all you can find is the "latest" package...
So I would still appreciate any help to be able to flash. Ok, now at least, I have a usable phone... but... I wanted to use it (as the other two) for ROM development testing, so who wants to have a PHONE!?!?
Kind regards from Switzerland - Christoph
Here is your radios
Sorry for the short post, I have a really bad hangover lol
http://forum.xda-developers.com/showthread.php?t=407956
Morn' Dave!
I tried them all - none of them was flashable... same 0%-bar.
I thought of having the V 1.00 complete official Swisscom-Pack and as part of it, the radio 1.00.25.05, which is included. Seems to me, that the c(complete) official ROM pack is flashable.
THEN I could re-try to flash Hard-SPL (with then installed radio below 1.02.xxx)
Hangover? What's this?
Christoph21x said:
Morn' Dave!
I tried them all - none of them was flashable... same 0%-bar.
I thought of having the V 1.00 complete official Swisscom-Pack and as part of it, the radio 1.00.25.05, which is included. Seems to me, that the c(complete) official ROM pack is flashable.
THEN I could re-try to flash Hard-SPL (with then installed radio below 1.02.xxx)
Hangover? What's this?
Click to expand...
Click to collapse
YEa that might work, it is almost certain the issue is the HARDSpl being either not flashed, or flashed with a signed version
Good luck !!
And the hangover is nearly gone... I cured yesterdays with more alcohol lol
Have you tried these UNSIGNED dev HARDspls ?
http://forum.xda-developers.com/showthread.php?t=400950
Hi Dave - GOT IT, solved
The "secret" was to flash noit from withi boot loader but from within Win Mobile with ActiveSync/Windows Device Center connected.
Then say "Yes" when "enterbootloader.exe" was asked to be installed/invoked.
Then the Device rebooted, flashed Hrd-SPL 1.40 correctly - and everything else onwards went fine.
Thanks a lot for your assitance, Dave and others.
Kind regards from Switzerland - Christoph
Ah.. I thought you were already using the Activesync and CustomRUU to flash it with !
Yes, the ROMs and Radios can be flashed from the storage card, but the Hard SPL needs to be done from Activesync / CUstomRUU
Pleased you got it working anyway