Hello,
It seems that flat cable which connects the slide-out screen is broken: the touch-screen doesn't work, and there's a white lines all over the screen while opening the device.
I've made a call to my local service center and they said that I need to change the whole touch screen because the cable is glued to it.
Is it right? Is there another way to fix the device rather paying $300 for a new screen?
i have also the same problem For my PDA2K , my flat cable which is comming from the screen under the slider is broken ,, half of the cable , i have the orange cable ,, is there any way to fix it
Thanks
Related
it just stopped working just like that...then i reflashed it n im stuck in the first screen where it says "tap to start" n i cant even tap now...anyone has any idea of how i can fix it at home...cuz its a lot of hassle to send it abroad...thank u
touch screen replacement
I had the same problem on my Universal and opened it to find out what happened.
I found the cable connecting the LCD and touch screen completely twisted.
Someone has played with it turning the screen in the same direction for many times without unscrewing it every time.
I manged to fix it partially soldering some wires that had gone loose.
Some wires were impossible to handle so I need a new wiring cable (it's a bunch of single ultra-tiny wires).
Now screen, mike and headpiece work again, but not the touch screen.
Do you have any idea if such a spare part can be found anywhere?
Possibly that would solve also your problem.
Who can have spare-parts?
Mario
Hmm....
Actually, not only the flex cable is originally twisted and looks funny out of the factory, you cannot turn the screen in the same direction more than it should be turned (e.g. from opened clamshell it only goes 180 degrees clockwise and cannot be turned anti-clockwise other than returning into its original position), it is stopped from turning by the way the hinge is designed. It is done specifically to prevent just the thing you described.
Generally even when some wires detach, the cable still performs fine, as the wires are not isolated and bunched together, as long as they do not detach from the connector itself. The fraying can happen when the flex cable is reinserted into the main case too roughly or one time too many, as the opening is fairly small and both cables need to be bent a certain way to fit through and pulled through in a particular sequence. Your problem could be caused by a faulty digitizer, it is connected to an LCD and if LCD performs fine, yet you lost sensitivity, the problem is not with your flex cable.
Cables can be purchased on Ebay. And so can digitizers (they are around $17-$20, but you need soldering to get them fitted to your LCD).
Hi dear developers!
I got a Touch Pro 2 from a friend, it's a GSM device he bought in Germany (O2). I changed a few parts but messed the main flex cable. The part from the power button is not connected anymore, a clean cut through, no repairs possible as far i think. So i bought a new one over ebay from Hong Kong. The seller told me it's for a GSM device BUT the cables do not look the same. The production date is 2008 and the damaged one was produced 2009. I built everything together and now the big surprise:
Phone boots normally but when the Home screen appears, it is always in landscape mode. No matter if the phone is closed or the keyboard open. I can only change the screen over advanced tools, but after soft reset again only landscape mode. The buttons for calling also do not work (those two down on the screen when you want to call someone or end a call ---> no reaction).
A hard reset and new ROM (energy) didn't change anything. By the way, the keyboard only fires up after pressing a button. Before it automatically lightened up after sliding.
What the hell is wrong now, did the send me a CDMA cable? Where is the difference ? Please help me i do not want to spent another 30 bucks again for a proper flex cable.
Edit: I disassembled the phone again and took a closer look on the flex cable: the lower part (with the LCD connection etc) looks quite same except for 3 or 4 transistors and their position on the PCB. The upper part with the earpice looks way different. The positioning of the single parts is not the same. But how can that interfere ? Guess there is no problem with the mainboard or the LCD (which is brand new).
Here are some pictures
h**p//img28.imageshack.us/img28/1514/image2sh
h**p://img849.imageshack.us/img849/8167/img1609m.jpg
OK, i solved the problem. The guy who sold the flex cable sent me a older one as I described. This thing was fully responsible for the errors. Bought a new one and everything works fine now^^ So if you ever want to change your Flex cable take good care which one you buy (especially on ebay!)
Btw: The display and the digitizer are glued and IF you want to replace any of those two, do yourself the favor and buy the complete bundle !!! I made the mistake and tried to replace the digitizer and cracked the display. There is no way as far as I can say, that you can manage this.
Bye
Can u post the seller info? Im in the same situation w a different phone... Thanks
Hi guys i have a problem
I can access different function through the MANUAL KEYS like settings, wireless , sound , display, and all the programs, but digitizer itself seems to be frozen.So i was wondering what is most common problem for that i presume flex cable or digitizer but digitizer is in good condition so what can it be ?
So cable 1 or 2?
1.http://www.ebay.com/itm/SLIDE-SLIDE...246?pt=LH_DefaultDomain_0&hash=item1e708e88f6
2.http://www.ebay.com/itm/New-Replace...363534?pt=PDA_Accessories&hash=item1c299ee54e
I had damaged flex cable, and touch screen was still working, but screen was showing TV static all the time.
PS: This link
http://www.ebay.com/itm/SLIDE-SLIDE...ultDomain_0&hash=item1e708e88f6#ht_1606wt_952
Second one is analog touch cable.
To me digitizer doesnt work but analog works ?Which cable is that?
anyone?
whenever I slide out my gamepad my phone does not change the screen mode from portrait to landscape, neither does the xperia play launcher starts or the screen gets unlocked.
sometimes the screen automatically changes the screen mode from portrait to landscape as if the gamepad has been slid out when it isn't.
also games like PES 2012 don't detect the gamepad anymore used to work earlier.
what is the exact problem?
I asked a local mobile repair shop and he says strip of slider (flex cable) must be changed but it isn't available anywhere in my area. if this is correct then I may order the flex cable online.
what do you guys have to say?
To the OP:
My replacement glass+digitizer didn't have adhesive behind the connector like the original so every time the phone would take a hit the screen would go blank. I'd have to take it all apart and reseat the connector. Sometimes the cable that connects to it would twist out a little bit on its own during reassembly and I'd have to do it again. Not I use precisely cut tape or hot glue when I do one (careful of the slide rails). Though my problem usually manifested as a blank screen, twice it manifested as an unresponsive digitizer.
I'd check my connection first.
bodygaurd said:
whenever I slide out my gamepad my phone does not change the screen mode from portrait to landscape, neither does the xperia play launcher starts or the screen gets unlocked.
sometimes the screen automatically changes the screen mode from portrait to landscape as if the gamepad has been slid out when it isn't.
also games like PES 2012 don't detect the gamepad anymore used to work earlier.
what is the exact problem?
I asked a local mobile repair shop and he says strip of slider (flex cable) must be changed but it isn't available anywhere in my area. if this is correct then I may order the flex cable online.
what do you guys have to say?
Click to expand...
Click to collapse
I responded to your PM. Yes, all the parts involved are available online. The slide board has two metal fingers inside a rail/slot that the bracket joining the two halves slides in. I don't know what the second one is for because all functions seem to react to the first one making or breaking a connection, but it could be causing the problem just as easily. These springy conductive fingers connect through the same flex cable as the switches that the face buttons press (Back, Home, Menu, Search) using some kind of conductive adhesive backing. That part is only a few bucks online, so it may be worth replacing just that to see. Unfortunately, the slider assembly is expensive (at least $20) but the slider + earpiece/camera + slide cable + switches is a comparative value at only a few bucks more.
idk but can any one explain to me why does my xperia play flex cable damage so easily i don't even use the game pad cuz this is like the 3rd time i'm replacing the cable
well the 2nd time i replaced the hole middle slider with flex cable and other stuff already installed and nw that cable is broken
i don't even know what to do anymore
RealMcoy said:
idk but can any one explain to me why does my xperia play flex cable damage so easily i don't even use the game pad cuz this is like the 3rd time i'm replacing the cable
well the 2nd time i replaced the hole middle slider with flex cable and other stuff already installed and nw that cable is broken
i don't even know what to do anymore
Click to expand...
Click to collapse
Maybe you slide the phone too fast or you push it too strong . My advice is you hold the screen while sliding it , gently and slowly . It may sound cheeky but ... I've been doing that since I first got my phone . And I never had any problem with the flex cable .
thats hw i always do it but i think that this cable damaged by the amount of sliding i did because i changed my digitizer as well (complete with sensors installed) and the proximity gave me some problems
so i had to slide up and dwn when calling to keep my screen alive
i think that damaged my brand new middle slide plate complete with all cables installed (including flex )
. .
Hi
Some time ago i had custom rom on my Xperia Play, but flex cable from screen died and i replaced it.
After that, my phone freezed on Lupud kernel logo, vibrate and nothing more. No recovery etc.
Today i flashed it through flashtool to stock rom, and it started, logo "sony ericsson" pop up and after few minutes it dissapeared.
Now if i push power button i se some "snow, mozaic" on screen.
I don't really know what do next. I thought it's kernel compatibility problem, but know it look like damaged flex cable.
But kernel logo looks perfectly, only on rom something is broken.
I will appreciate any help.
IMHO, i think it's flex cable again.
I had also had similar problem.
1st and 2nd flex replacement went without problem
3rd was just black screen. It did vibrate, but nothing was on screen.
4th was half working (it show/stay on lupus logo and 1 in 10 tries it boot into rom but without touchscreen working)
5th was working on first try
It is hit&miss logic. Maybe it's problem with crappy quality, maybe it is problem with zif connectors on slider flex cable.
Try your flex cable again, but this time, first insert flex cable that goes from front camera/proximity sensor into zif connector of slider flex cable, and see how much actually is "good connection". Then press slider flex cable into possition and compare to your previous observation. If it's even 1/2 of mm away, it could be bad connection (flex from camera is not inserted fully in zif connector). Best position to be sure is that front camera flex have a very small "belly" (curved shape).
It looks like your 4th cable. I will try mounting it few times and order new one.
Now i realized, that "snow/mozaic" shows after screen shut down to save energy.
P.S.
For those from the future which will looking for solution for problem similar to mine.
Yes, it worked. Flex cable can work and don't in the same time.